I use 3.2.0-24-generic-phc. I can install/load the emc2103 -module @ startup or with modprobe. It even shows up with lsmod, but nothing happens. Or is there some way I can use it? Maybe its somehow possible to manually edit the cip IDs so that ID ID 0x4501 is recognized as emc2103?
The problem is just that my notebook really heats up, so I want the fan to run faster. Even @ 80°C it just runs with 50% speed.
Last edited by sebl; May 27th, 2012 at 07:46 PM.
What's the output from the sensors command? Sorry, can't help with fan speed. Maybe someone else can.
Did you look at the lm-sensors FAQ?
lm-sensors FAQ
Last edited by akernan; May 27th, 2012 at 09:09 PM.
sensors only shows temperatures:
With or withour the emc2103 driver loadedacpitz-virtual-0
Adapter: Virtual device
temp1: +48.0°C (crit = +105.0°C)
temp2: +37.4°C (crit = +110.0°C)
temp3: +62.0°C (crit = +110.0°C)
temp4: +57.0°C (crit = +90.0°C)
temp5: +57.0°C (crit = +105.0°C)
coretemp-isa-0000
Adapter: ISA adapter
Core 0: +62.0°C (high = +105.0°C, crit = +105.0°C)
Core 1: +63.0°C (high = +105.0°C, crit = +105.0°C)
@sebl Did you check your fan for dust? (In the category "Answers that are not related to lm-sensors".) With notebooks you often only need to lift the keyboard to reach/clean the fan. The heatsink can be dusty too, but it's more difficult to reach. Use a new/clean paintbrush, old toothbrush or compressed air (you can buy it in spraypaint-like cans).
For the CPU temperature you can ignore the acpitz-virtual-0 temps, I've found them not to be accurate. It's the coretemp-isa-0000 temps you need to keep an eye on.
My netbook went over 70°C a few days ago. In the sun, air temps just under 30°C And I didn't even make the machine work that hard.
I am a bit confused. I feel like I installed and setup lm-sensors on Ubuntu 12.04 and Arch Linux in exactly the same way, but running sensors gives me much more output on Arch than it does on Precise. It seems like something is not working on Precise or I have done something wrong.
Also, when I try to start or restart service module-init-tools, it just immediately replies that it is in status "stop/waiting". My guess is that this is where my problem lies.
Here is my output on Ubuntu 12.04:
Here is the sensors output from Arch Linux:coretemp-isa-0000
Adapter: ISA adapter
Physical id 0: +37.0°C (high = +80.0°C, crit = +98.0°C)
Core 0: +35.0°C (high = +80.0°C, crit = +98.0°C)
Core 1: +37.0°C (high = +80.0°C, crit = +98.0°C)
Core 2: +35.0°C (high = +80.0°C, crit = +98.0°C)
Core 3: +38.0°C (high = +80.0°C, crit = +98.0°C)
What is wrong on Ubuntu?radeon-pci-0100
Adapter: PCI adapter
temp1: +60.0 C
coretemp-isa-0000
Adapter: ISA adapter
Physical id 0: +39.0 C (high = +80.0 C, crit = +98.0 C)
Core 0: +39.0 C (high = +80.0 C, crit = +98.0 C)
Core 1: +37.0 C (high = +80.0 C, crit = +98.0 C)
Core 2: +36.0 C (high = +80.0 C, crit = +98.0 C)
Core 3: +39.0 C (high = +80.0 C, crit = +98.0 C)
it8728-isa-0290
Adapter: ISA adapter
in0: +1.04 V (min = +0.00 V, max = +3.06 V)
in1: +2.04 V (min = +0.00 V, max = +3.06 V)
in2: +2.93 V (min = +0.00 V, max = +3.06 V)
in3: +2.98 V (min = +0.00 V, max = +3.06 V)
in4: +0.00 V (min = +0.00 V, max = +3.06 V) ALARM
in5: +0.74 V (min = +0.00 V, max = +3.06 V)
in6: +1.54 V (min = +0.00 V, max = +3.06 V)
3VSB: +3.36 V (min = +0.00 V, max = +6.12 V)
Vbat: +3.29 V
fan1: 1421 RPM (min = 0 RPM)
fan2: 0 RPM (min = 0 RPM)
fan3: 1231 RPM (min = 0 RPM)
fan4: 0 RPM (min = 0 RPM)
temp1: +39.0 C (low = +127.0 C, high = +127.0 C) sensor = thermistor
temp2: +25.0 C (low = +127.0 C, high = +127.0 C) sensor = thermistor
temp3: +28.0 C (low = +127.0 C, high = +127.0 C) sensor = thermistor
intrusion0: ALARM
Tim
PS - Never mind. I need to go to post 1 and work my way through all that beginning info. But, I didn't need to do anything like all that on Arch. Sorry.
Last edited by ratcheer; June 9th, 2012 at 08:48 PM. Reason: Add Arch Linux output
Cyberpower PC, Core i5 2500 3.3 gHz, 8GB DDR3, ATI 6770 1GB, Samsung BX 2440 LED 1080p, 1 TB SATA III, 2 TB SATA III, Siduction Linux 64-bit
See the preceding post. Now, I have followed post #1 instructions and I get the same results. It seems to find another sensor, but it does not include it in the stuff it says to add to /etc/modules. It only says to add coretemp, which is already there.
So, it finds a "Chip `ITE IT8728F Super IO Sensors' (confidence: 9)", but then says there is no driver for it. Apparently, the driver is found and used in lm-sensors on Arch Linux. Is there a way to find and load this driver on Ubuntu?Just press ENTER to continue:
Driver `to-be-written':
* ISA bus, address 0x290
Chip `ITE IT8728F Super IO Sensors' (confidence: 9)
Driver `coretemp':
* Chip `Intel digital thermal sensor' (confidence: 9)
Note: there is no driver for ITE IT8728F Super IO Sensors yet.
Check http://www.lm-sensors.org/wiki/Devices for updates.
To load everything that is needed, add this to /etc/modules:
#----cut here----
# Chip drivers
coretemp
#----cut here----
If you have some drivers built into your kernel, the list above will
contain too many modules. Skip the appropriate ones!
Also, there is a module it87.ko in my drivers folder, but if I try to modprobe it, it responds that it does not exist. ???
Tim
PS - Later [SOLVED]
Downloaded newer driver from http://khali.linux-fr.org/devel/misc/it87/
Ran make, make install, modprobe it87
sensors now returns all the info expected
coretemp-isa-0000
Adapter: ISA adapter
Physical id 0: +39.0°C (high = +80.0°C, crit = +98.0°C)
Core 0: +36.0°C (high = +80.0°C, crit = +98.0°C)
Core 1: +38.0°C (high = +80.0°C, crit = +98.0°C)
Core 2: +37.0°C (high = +80.0°C, crit = +98.0°C)
Core 3: +39.0°C (high = +80.0°C, crit = +98.0°C)
it8728-isa-0290
Adapter: ISA adapter
in0: +1.04 V (min = +0.00 V, max = +3.06 V)
in1: +2.04 V (min = +0.00 V, max = +3.06 V)
in2: +2.98 V (min = +0.00 V, max = +3.06 V)
in3: +2.96 V (min = +0.00 V, max = +3.06 V)
in4: +0.00 V (min = +0.00 V, max = +3.06 V) ALARM
in5: +0.74 V (min = +0.00 V, max = +3.06 V)
in6: +1.54 V (min = +0.00 V, max = +3.06 V)
3VSB: +3.36 V (min = +0.00 V, max = +6.12 V)
Vbat: +3.29 V
fan1: 1412 RPM (min = 0 RPM)
fan2: 0 RPM (min = 0 RPM)
fan3: 1247 RPM (min = 0 RPM)
fan4: 0 RPM (min = 0 RPM)
temp1: +40.0°C (low = +127.0°C, high = +127.0°C) sensor = thermistor
temp2: +25.0°C (low = +127.0°C, high = +127.0°C) sensor = thermistor
temp3: +29.0°C (low = +127.0°C, high = +127.0°C) sensor = thermistor
intrusion0: ALARM
Last edited by ratcheer; June 10th, 2012 at 03:08 PM. Reason: Add solution
Cyberpower PC, Core i5 2500 3.3 gHz, 8GB DDR3, ATI 6770 1GB, Samsung BX 2440 LED 1080p, 1 TB SATA III, 2 TB SATA III, Siduction Linux 64-bit
Recently I got the feeling that lm-sensors (or coretemp) CPU temperature readings are way off.
I'm currently running kernel 3.2.0-30-generic and 3.2.0-31-generic on two different machines. My older Core2 machine ran Linux Mint 9 before and temperatures were well below 40C when idle. Now they are in the 50s.
On my new machine with an Intel 3930K CPU I also noticed higher temperature readings, but I can't remember exactly when it started (meaning which kernel update or lm-sensors update produced the problem).
Anyone noticed something similar? I believe the CPU temperatures reported by lm-sensors are some 15-20C higher than the actual temperature, or at least how the BIOS reads the temperature.
Hi guys. This is my konsole output
this is modules:Code:# sensors-detect revision 5984 (2011-07-10 21:22:53 +0200) # System: LENOVO 20091 (laptop) # Board: LENOVO Base Board Product Name This program will help you determine which kernel modules you need to load to use lm_sensors most effectively. It is generally safe and recommended to accept the default answers to all questions, unless you know what you're doing. Some south bridges, CPUs or memory controllers contain embedded sensors. Do you want to scan for them? This is totally safe. (YES/no): y Module cpuid loaded successfully. Silicon Integrated Systems SIS5595... No VIA VT82C686 Integrated Sensors... No VIA VT8231 Integrated Sensors... No AMD K8 thermal sensors... No AMD Family 10h thermal sensors... No AMD Family 11h thermal sensors... No AMD Family 12h and 14h thermal sensors... No AMD Family 15h thermal sensors... No AMD Family 15h power sensors... No Intel digital thermal sensor... Success! (driver `coretemp') Intel AMB FB-DIMM thermal sensor... No VIA C7 thermal sensor... No VIA Nano thermal sensor... No Some Super I/O chips contain embedded sensors. We have to write to standard I/O ports to probe them. This is usually safe. Do you want to scan for Super I/O sensors? (YES/no): y Probing for Super-I/O at 0x2e/0x2f Trying family `National Semiconductor/ITE'... No Trying family `SMSC'... No Trying family `VIA/Winbond/Nuvoton/Fintek'... No Trying family `ITE'... No Probing for Super-I/O at 0x4e/0x4f Trying family `National Semiconductor/ITE'... No Trying family `SMSC'... No Trying family `VIA/Winbond/Nuvoton/Fintek'... No Trying family `ITE'... No Some hardware monitoring chips are accessible through the ISA I/O ports. We have to write to arbitrary I/O ports to probe them. This is usually safe though. Yes, you do have ISA I/O ports even if you do not have any ISA slots! Do you want to scan the ISA I/O ports? (YES/no): y Probing for `National Semiconductor LM78' at 0x290... No Probing for `National Semiconductor LM79' at 0x290... No Probing for `Winbond W83781D' at 0x290... No Probing for `Winbond W83782D' at 0x290... No Lastly, we can probe the I2C/SMBus adapters for connected hardware monitoring devices. This is the most risky part, and while it works reasonably well on most systems, it has been reported to cause trouble on some systems. Do you want to probe the I2C/SMBus adapters now? (YES/no): y Using driver `i2c-i801' for device 0000:00:1f.3: Intel Cougar Point (PCH) Module i2c-i801 loaded successfully. Module i2c-dev loaded successfully. Next adapter: i915 gmbus ssc (i2c-0) Do you want to scan it? (YES/no/selectively): y Next adapter: i915 gmbus vga (i2c-1) Do you want to scan it? (YES/no/selectively): y Next adapter: i915 gmbus panel (i2c-2) Do you want to scan it? (YES/no/selectively): y Client found at address 0x50 Probing for `Analog Devices ADM1033'... yNo Probing for `Analog Devices ADM1034'... No Probing for `SPD EEPROM'... No Probing for `EDID EEPROM'... Yes (confidence 8, not a hardware monitoring chip) Next adapter: i915 gmbus dpc (i2c-3) Do you want to scan it? (YES/no/selectively): Next adapter: i915 gmbus dpb (i2c-4) Do you want to scan it? (YES/no/selectively): y Next adapter: i915 gmbus dpd (i2c-5) Do you want to scan it? (YES/no/selectively): y Next adapter: DPDDC-B (i2c-6) Do you want to scan it? (YES/no/selectively): y Now follows a summary of the probes I have just done. Just press ENTER to continue: Driver `coretemp': * Chip `Intel digital thermal sensor' (confidence: 9) To load everything that is needed, add this to /etc/modules: #----cut here---- # Chip drivers coretemp #----cut here---- If you have some drivers built into your kernel, the list above will contain too many modules. Skip the appropriate ones! Do you want to add these lines automatically to /etc/modules? (yes/NO)y Successful! Monitoring programs won't work until the needed modules are loaded. You may want to run 'service module-init-tools start' to load them. Unloading i2c-dev... OK Unloading i2c-i801... OK Unloading cpuid... OK
and this is my sensors output:Code:# /etc/modules: kernel modules to load at boot time. # # This file contains the names of kernel modules that should be loaded # at boot time, one per line. Lines beginning with "#" are ignored. lp rtc # Generated by sensors-detect on Tue Nov 27 15:57:19 2012 # Chip drivers coretemp
now where is the problem ? Did i something wrong ?Code:acpitz-virtual-0 Adapter: Virtual device temp1: +61.0°C (crit = +127.0°C) coretemp-isa-0000 Adapter: ISA adapter Physical id 0: +60.0°C (high = +86.0°C, crit = +100.0°C) Core 0: +57.0°C (high = +86.0°C, crit = +100.0°C) Core 1: +59.0°C (high = +86.0°C, crit = +100.0°C) Core 2: +57.0°C (high = +86.0°C, crit = +100.0°C) Core 3: +59.0°C (high = +86.0°C, crit = +100.0°C)
Bookmarks