Will not install: Asus Usb-ax56 Dual Band Ax1800

**chili555** · March 19th, 2024

Did you try a reboot?

After the reboot, did the module load as expected?

Code:

lsmod | grep 8852au

Was a wireless interface created?

Code:

iwconfig

Does it see networks?

Code:

nmcli device wifi list

PS - The 'getting old' card is hard to play here. I am confident that I have at least a decade on you!

**sgt-mike** · March 20th, 2024

No I didn't reboot did not even think about doing that.

Code:

  mike@bastion:~$ lsmod | grep 8852au
8852au              13557760  0
cfg80211              974848  1 8852au

mike@bastion:~$ iwconfig
lo        no wireless extensions.

eno1      no wireless extensions.

mike@bastion:~$ nmcli device wifi list
mike@bastion:~$

IDK if it makes an difference it is a USB wireless adapter which I'm positive most already know that

**chili555** · March 20th, 2024

Let's see if there are any clues in the message log:

Code:

sudo dmesg | grep 8852

**sgt-mike** · March 20th, 2024

that returns

Code:

mike@bastion:~$ sudo dmesg | grep 8852
[sudo] password for mike: 
[    0.208852] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[   28.996885] 8852au: loading out-of-tree module taints kernel.
[   29.001902] 8852au: module verification failed: signature and/or required key missing - tainting kernel
[   29.024589] usbcore: registered new interface driver rtl8852au

**chili555** · March 20th, 2024

My very favorite kind of problem: everything looks great except it just doesn't work.

Please shut down the computer. Remove the USB wireless. Start the computer. Open a terminal and run:

Code:

tail -f /var/log/syslog

Insert the USB wireless. Capture the output in the terminal and post it here.

Get out of 'tail' with Ctrl+c.

Is it possible that the USB wireless needs a USB 3.0 (or greater) port but it is currently plugged in to a USB 2.0 port?

**praseodym** · March 22nd, 2024

Code:

[   29.001902] 8852au: module verification failed: signature and/or required key missing - tainting kernel

Driver not signed. Deactivate SecureBoot

**sgt-mike** · March 23rd, 2024

Originally Posted by chili555

My very favorite kind of problem: everything looks great except it just doesn't work.

Please shut down the computer. Remove the USB wireless. Start the computer. Open a terminal and run:

Code:

tail -f /var/log/syslog

Insert the USB wireless. Capture the output in the terminal and post it here.

Get out of 'tail' with Ctrl+c.

Is it possible that the USB wireless needs a USB 3.0 (or greater) port but it is currently plugged in to a USB 2.0 port?

Sorry for my delay in posting

I obtained the usb wireless device to use when the media server (or my NFS) was disconnected from a wired connection.
It was/is a nice to have item not required. With that in mind I removed the device driver to get out of the kernal tainted status.

But your last question is a true statement it is a USB 3.0 device plugged into a USB 2.0 port. That could very well be a major part of the problem, even though it's supposed to be backwardly compatible it may not be.

And to praseodym post:

secure boot --- I don't recall setting it up unless it was a default setting from Ubuntu 22.04 server install, and I don't doubt that it is, I'll research that to disable that --- it very well maybe the whole underlying fault
This may take a week or two before I can revisit this small issue (I need to flush a tractor's fuel system, joy oh joy, which means almost complete deck and rear end assembly removal to get to the fuel tank). maybe less.

After reading both post's I'll re-install the driver and do as Chilli stated and capture the output.
Then I'll disable the secure boot if it's enabled after running down the output that Chilli advised.

**declanshanaghy2** · 4 Weeks Ago

Originally Posted by chili555

The correct driver for this device is here: https://github.com/lwfinger/rtl8852au

Code:

$ modinfo 8852au.ko | grep 1997
alias:          usb:v0B05p1997d*dc*dsc*dp*icFFiscFFipFFin*

Post back if you need step-by-step instructions.

I just got this WiFi dongle, which as far as I can figure out is the same one being referred to here.

Because the USB Id's match up:
From the repo: ASUS USB-AX56 with USB ID 0b05:1a62
Fom lsusb: Bus 001 Device 006: ID 0b05:1a62 ASUSTek Computer, Inc.

In this case, im just lucky that the repo README has the USB IDs in the list, a lot of devs don't go to that level of detail.

My question is how did you find this repo?
In the general case...what's the secret sauce for finding a driver?

**jeremy31** · 4 Weeks Ago

Originally Posted by declanshanaghy2

I just got this WiFi dongle, which as far as I can figure out is the same one being referred to here.

Because the USB Id's match up:
From the repo: ASUS USB-AX56 with USB ID 0b05:1a62
Fom lsusb: Bus 001 Device 006: ID 0b05:1a62 ASUSTek Computer, Inc.

In this case, im just lucky that the repo README has the USB IDs in the list, a lot of devs don't go to that level of detail.

My question is how did you find this repo?
In the general case...what's the secret sauce for finding a driver?

We normally do a net search for the USB ID and see where it leads, hopefully we find something that is patched for newer kernels
Sometimes for Realtek wifi you can search the /os_dep/linux/usb_intf.c for part of the USB ID

**declanshanaghy2** · 4 Weeks Ago

Ahhh ****, I ran into issues compiling the module.
I'm on a Raspberry Pi, which has a + in the kernel release version (5.4.79-v7+). apt treats that as a special symbol.
Here's how to install kernel headers for RasPi - apt install raspberrypi-kernel-headers

Next issue I ran into is that my kernel was too old.
The ole apt-get dist-upgrade sledgehammer solved that for me

She's compiling now!