Hi,
I am new to Linux, my monitor couldn't be recognized, tried couple ways to add resolution, it doesn't work, hope someone could help me out here.
Code:cvt 1680 1050 # 1680x1050 59.95 Hz (CVT 1.76MA) hsync: 65.29 kHz; pclk: 146.25 MHz Modeline "1680x1050_60.00" 146.25 1680 1784 1960 2240 1050 1053 1059 1089 -hsync +vsync xrandr --newmode "1680x1050_60.00" 146.25 1680 1784 1960 2240 1050 1053 1059 1089 -hsync +vsync xrandr --addmode DVI-D-0 "1680x1050_60.00" X Error of failed request: BadMatch (invalid parameter attributes) Major opcode of failed request: 140 (RANDR) Minor opcode of failed request: 18 (RRAddOutputMode) Serial number of failed request: 35 Current serial number in output stream: 36Code:xrandr Screen 0: minimum 8 x 8, current 1984 x 768, maximum 16384 x 16384 VGA-0 connected primary 1024x768+0+0 (normal left inverted right x axis y axis) 304mm x 228mm 1024x768 60.00*+ 75.03 70.07 800x600 75.00 72.19 60.32 56.25 640x480 75.00 72.81 59.95 59.94 DVI-D-0 connected 960x540+1024+101 (normal left inverted right x axis y axis) 0mm x 0mm 960x540 59.82*+ 864x486 59.92 59.57 640x480 59.94 480x270 59.82 432x243 59.92 59.57 320x240 60.05 HDMI-0 disconnected (normal left inverted right x axis y axis) Mode 0 (0x2c0) 146.250MHz -HSync +VSync h: width 1680 start 1784 end 1960 total 2240 skew 0 clock 65.29KHz v: height 1050 start 1053 end 1059 total 1089 clock 59.95Hz Mode 1680 (0x2ce) 146.250MHz -HSync +VSync h: width 1680 start 1784 end 1960 total 2240 skew 0 clock 65.29KHz v: height 1050 start 1053 end 1059 total 1089 clock 59.95HzCode:lspci -vk | grep -iA15 vga 01:00.0 VGA compatible controller: NVIDIA Corporation GK208 [GeForce GT 710B] (rev a1) (prog-if 00 [VGA controller]) Subsystem: Micro-Star International Co., Ltd. [MSI] GK208B [GeForce GT 710] Flags: bus master, fast devsel, latency 0, IRQ 31 Memory at f9000000 (32-bit, non-prefetchable) [size=16M] Memory at e0000000 (64-bit, prefetchable) [size=128M] Memory at ee000000 (64-bit, prefetchable) [size=32M] I/O ports at bf00 [size=128] [virtual] Expansion ROM at 000c0000 [disabled] [size=128K] Capabilities: <access denied> Kernel driver in use: nvidia Kernel modules: nvidiafb, nouveau, nvidia_drm, nvidia 01:00.1 Audio device: NVIDIA Corporation GK208 HDMI/DP Audio Controller (rev a1) Subsystem: Micro-Star International Co., Ltd. [MSI] GK208 HDMI/DP Audio Controller Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at faffc000 (32-bit, non-prefetchable) [size=16K]Code:sudo get-edid | parse-edid This is read-edid version 3.0.2. Prepare for some fun. Attempting to use i2c interface No EDID on bus 0 No EDID on bus 1 No EDID on bus 2 No EDID on bus 3 No EDID on bus 4 No EDID on bus 5 No EDID on bus 6 No EDID on bus 7 No EDID on bus 10 2 potential busses found: 8 9 Will scan through until the first EDID is found. Pass a bus number as an option to this program to go only for that one. 256-byte EDID successfully retrieved from i2c bus 8 Looks like i2c was successful. Have a good day. WARNING: Checksum failed Trying to continue... Section "Monitor" Identifier "VX2235wm" ModelName "VX2235wm" VendorName "VSC" # Monitor Manufactured week 5 of 2007 # EDID version 1.3 # Digital Display DisplaySize 470 300 Gamma 2.20 Option "DPMS" "true" Horizsync 30-82 VertRefresh 50-75 # Maximum pixel clock is 150MHz #Not giving standard mode: 1680x1050, 60Hz #Not giving standard mode: 1600x1200, 60Hz #Not giving standard mode: 1440x900, 60Hz #Not giving standard mode: 1400x1050, 60Hz #Not giving standard mode: 1280x1024, 60Hz #Not giving standard mode: 1280x960, 60Hz #Not giving standard mode: 1152x864, 75Hz #Not giving standard mode: 640x400, 70Hz Modeline "Mode 0" 146.25 1680 1784 1960 2240 1050 1053 1059 1089 -hsync +vsync
Adv Reply
Bookmarks