Hello,
I've just installed Ubuntu 18.04.1 to a server with Supermicro Motherboard X11SSH-TF with Graphics Aspeed AST2400 BMC build in and during boot up graphics get slow.
I've recorded video example.
During boot up is changed resolution (not possible to calibrate lcd) and everything is slowed down. LCD is connected with VGA cable (no other connector on motherboard).
When I tried to install Aspeed driver, this message is returned:
Code:
Can't find proper X Window Version, Please update driver manually!!
Also Ubuntu Server installer was "bigger" than the screen.
Any idea?
lshw:
Code:
*-pci
description: PCI bridge
product: AST1150 PCI-to-PCI Bridge
vendor: ASPEED Technology, Inc.
physical id: 0
bus info: pci@0000:02:00.0
version: 03
width: 32 bits
clock: 33MHz
capabilities: pci msi pm pciexpress normal_decode bus_master cap_list
resources: ioport:e000(size=4096) memory:de000000-df0fffff
*-display
description: VGA compatible controller
product: ASPEED Graphics Family
vendor: ASPEED Technology, Inc.
physical id: 0
bus info: pci@0000:03:00.0
version: 30
width: 32 bits
clock: 33MHz
capabilities: pm msi vga_controller bus_master cap_list rom
configuration: driver=ast latency=0
resources: irq:18 memory:de000000-deffffff memory:df000000-df01ffff ioport:e000(size=128) memory:c0000-dffff
dmesg:
Code:
[ 9.593618] ata2.00: Enabling discard_zeroes_data
[ 11.182667] AVX2 version of gcm_enc/dec engaged.
[ 11.182667] AES CTR mode by8 optimization enabled
[ 12.141034] sdb: sdb1
[ 12.141037] sda: sda1
[ 12.141177] ata1.00: Enabling discard_zeroes_data
[ 12.144946] sd 0:0:0:0: [sda] supports TCG Opal
[ 12.144948] sd 0:0:0:0: [sda] Attached SCSI disk
[ 12.501827] ata2.00: Enabling discard_zeroes_data
[ 12.576187] sd 1:0:0:0: [sdb] supports TCG Opal
[ 12.644806] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 12.712732] dca service started, version 1.12.1
[ 12.784242] ixgbe: Intel(R) 10 Gigabit PCI Express Network Driver - version 5.1.0-k
[ 12.784676] [drm] Using P2A bridge for configuration
[ 12.784687] [drm] AST 2400 detected
[ 12.784777] [drm] Analog VGA only
[ 12.784890] [drm] dram MCLK=408 Mhz type=1 bus_width=16 size=01000000
[ 12.784953] [TTM] Zone kernel: Available graphics memory: 16380210 kiB
[ 12.784954] [TTM] Zone dma32: Available graphics memory: 2097152 kiB
[ 12.784954] [TTM] Initializing pool allocator
[ 12.784964] [TTM] Initializing DMA pool allocator
[ 13.036775] checking generic (de000000 6c0000) vs hw (de000000 1000000)
[ 13.036775] fb: switching to astdrmfb from VESA VGA
[ 13.299132] md/raid1:md0: active with 2 out of 2 mirrors
[ 13.304440] md0: detected capacity change from 0 to 499970473984
[ 13.311544] random: fast init done
[ 13.761199] ixgbe: Copyright (c) 1999-2016 Intel Corporation.
[ 13.761261] Console: switching to colour dummy device 80x25
[ 13.761405] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[ 13.761455] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[ 13.761458] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[ 13.761486] fbcon: astdrmfb (fb0) is primary device
[ 14.504339] ixgbe 0000:04:00.0: Multiqueue Enabled: Rx Queue count = 8, Tx Queue count = 8 XDP Queue count = 0
[ 14.547375] ixgbe 0000:04:00.0: PCI Express bandwidth of 32GT/s available
[ 14.547376] ixgbe 0000:04:00.0: (Speed:8.0GT/s, Width: x4, Encoding Loss:<2%)
[ 14.576058] ixgbe 0000:04:00.0: MAC: 4, PHY: 0, PBA No: 020A00-000
[ 14.576059] ixgbe 0000:04:00.0: ac:1f:6b:6a:a8:7e
[ 14.741565] ixgbe 0000:04:00.0: Intel(R) 10 Gigabit Network Connection
[ 15.304828] Console: switching to colour frame buffer device 240x67
[ 15.483836] ixgbe 0000:04:00.1: Multiqueue Enabled: Rx Queue count = 8, Tx Queue count = 8 XDP Queue count = 0
[ 15.526960] ixgbe 0000:04:00.1: PCI Express bandwidth of 32GT/s available
[ 15.526961] ixgbe 0000:04:00.1: (Speed:8.0GT/s, Width: x4, Encoding Loss:<2%)
[ 15.555653] ixgbe 0000:04:00.1: MAC: 4, PHY: 0, PBA No: 020A00-000
[ 15.555654] ixgbe 0000:04:00.1: ac:1f:6b:6a:a8:7f
[ 15.720304] ixgbe 0000:04:00.1: Intel(R) 10 Gigabit Network Connection
Bookmarks