Results 1 to 4 of 4

Thread: Extremely slow network - slow iperf performance

Threaded View

  1. #1
    Join Date
    Oct 2012

    Extremely slow network - slow iperf performance

    Hi all,

    This is my first post to these forums. I've been playing with Ubuntu for a while now and have used these forums to help me out with many problems, unfortunately I cant seem to fix my current problem.

    I've setup a box (HP Proliant Microserver N36L) running Ubuntu Server 64bit 12.04.1 LTS to act mainly as NAS and I'm experiencing extremely slow network speeds.

    I know the various file sharing protocols will be slower than raw speed but my problem seems to stem from the raw speed.

    Firstly my hardware: HP N36L has onboard gigabit lan. Using cat 6 cable connected to 10/100Mb capable router, then wireless to Apple Macbook.

    Right so my network interface is reduced to 100Mb(router) but surely I should still be getting better results with iperf than this:

    Server listening on TCP port 5001
    TCP window size: 85.3 KByte (default)
    [  4] local port 5001 connected with port 56451
    [ ID] Interval       Transfer     Bandwidth
    [  4]  0.0-10.0 sec  13.6 MBytes  11.4 Mbits/sec
    In fairness this result is pretty good I'm usually hitting around 5Mbits/sec

    Here is some more information I think is relevant (cant find any problems in any of it):

    ethtool eth0:
    Settings for eth0:
    	Supported ports: [ TP ]
    	Supported link modes:   10baseT/Half 10baseT/Full 
    	                        100baseT/Half 100baseT/Full 
    	                        1000baseT/Half 1000baseT/Full 
    	Supported pause frame use: No
    	Supports auto-negotiation: Yes
    	Advertised link modes:  10baseT/Half 10baseT/Full 
    	                        100baseT/Half 100baseT/Full 
    	                        1000baseT/Half 1000baseT/Full 
    	Advertised pause frame use: Symmetric
    	Advertised auto-negotiation: Yes
    	Speed: 100Mb/s
    	Duplex: Full
    	Port: Twisted Pair
    	PHYAD: 1
    	Transceiver: internal
    	Auto-negotiation: on
    	MDI-X: Unknown
    	Supports Wake-on: g
    	Wake-on: g
    	Current message level: 0x000000ff (255)
    			       drv probe link timer ifdown ifup rx_err tx_err
    	Link detected: yes
    dmesg | grep eth0:
    [    2.714157] tg3 0000:02:00.0: eth0: Tigon3 [partno(BCM95723) rev 5784100] (PCI Express) MAC address 3c:4a:92:74:2c:2c
    [    2.714222] tg3 0000:02:00.0: eth0: attached PHY is 5784 (10/100/1000Base-T Ethernet) (WireSpeed[1], EEE[0])
    [    2.714271] tg3 0000:02:00.0: eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
    [    2.714317] tg3 0000:02:00.0: eth0: dma_rwctrl[76180000] dma_mask[64-bit]
    [   22.348755] ADDRCONF(NETDEV_UP): eth0: link is not ready
    [   29.196436] ADDRCONF(NETDEV_UP): eth0: link is not ready
    [   30.784099] tg3 0000:02:00.0: eth0: Link is up at 100 Mbps, full duplex
    [   30.784105] tg3 0000:02:00.0: eth0: Flow control is off for TX and off for RX
    [   30.784336] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
    [   40.880052] eth0: no IPv6 routers present
    UPDATED - this might help aswel!

    sudo lshw -C network

           description: Ethernet interface
           product: NetXtreme BCM5723 Gigabit Ethernet PCIe
           vendor: Broadcom Corporation
           physical id: 0
           bus info: pci@0000:02:00.0
           logical name: eth0
           version: 10
           serial: 3c:4a:92:74:2c:2c
           size: 100Mbit/s
           capacity: 1Gbit/s
           width: 64 bits
           clock: 33MHz
           capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation
           configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.121 duplex=full firmware=5723-v3.35 ip= latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s
           resources: irq:42 memory:fe9f0000-fe9fffff
    I'm sure there's something I've missed. At the moment I'm using netatalk to share with my macbook as I understand it's faster than samba but it's pretty much useless to stream videos from at these speeds.

    I very much hope someone out there can help. Every other post out there seems to be someone with good iperf results and poor smb speeds. I've just got terrible iperf results!!!
    Last edited by James2012; October 2nd, 2012 at 11:07 PM. Reason: Including lshw output


Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts