Vodafone K3805-Z Mobile Broadband

[dunbrokin]

I have hte K3805-Z and am trying to get it to work....it seems to be recognised by the Network Manager....but I am not getting through.

usb-devices yields the following:

T: Bus=02 Lev=02 Prnt=02 Port=01 Cnt=01 Dev#= 11 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=02(commc) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=19d2 ProdID=1003 Rev=00.01
S: Manufacturer=Vodafone
S: Product=K3805-z
S: SerialNumber=C7986D8B72DFB07EF2FAE8645D14803D06F92 E84
C: #Ifs=10 Cfg#= 1 Atr=80 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 0 Cls=02(commc) Sub=08 Prot=00 Driver=(none)
I: If#= 1 Alt= 0 #EPs= 1 Cls=02(commc) Sub=02 Prot=01 Driver=cdc_acm
I: If#= 2 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_acm
I: If#= 3 Alt= 0 #EPs= 1 Cls=02(commc) Sub=02 Prot=01 Driver=cdc_acm
I: If#= 4 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_acm
I: If#= 5 Alt= 0 #EPs= 1 Cls=02(commc) Sub=06 Prot=00 Driver=cdc_ether
I: If#= 6 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
I: If#= 7 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
/usr/bin/usb-devices: line 79: printf: 08: invalid octal number
I: If#= 0 Alt= 0 #EPs= 0 Cls=02(commc) Sub=0b Prot=00 Driver=(none)
/usr/bin/usb-devices: line 79: printf: 09: invalid octal number
I: If#= 0 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=(none)

Where do I go from here?

[alexfish]

can have a look at this thread
Vodafone USB

athough a different ID the device looks similar


possible try the script at post #23

where it says

set Vendor "19d2"
set Product "1002"

change to

set Vendor "19d2"
set Product "1003"

this may show the ports but can't confirm .

also can try and find the device produced by lshal
may be something like ttyACM* or /dev

lshal > `pwd`/voda

the file should be in home directory
possible find the device ID's

in the blocks with device ID . also look for lines

linux.sysfs_path =

serial.device =

alexfish

[dunbrokin]

Here is a screen shot.

[alexfish]

HI

yes it shows a connection.....

could post details of a :how to : would be most helpful to others trying to connect

regards

alexfish

[dunbrokin]

HI

yes it shows a connection.....

could post details of a :how to : would be most helpful to others trying to connect

regards

alexfish

At this stage I have done nothing....this shows when I plug in the device...I still cannot get onto the Mobile Network. The problem is not helped by the fact that I do not have mobile reception here at home.

[alexfish]

hi

from the screen shot it looked as if you had a connection / the image is blurry

From what I gather your still looking for a solution

as a update from the other thread , there is a post where the device shows tttACM0

could see if there is dev serial ttyACM

can try

ls -al /dev/serial/by-id

if there is a listing at the end with ttyACM0 or others

then the connection path could be /dev/ttyACM0

with this info could try wvdial

but may need other info from the device : dial command , and or possible the APN

to find the APN's can have a look at this how to

How To : Mobile Broadband Connections [ Ubuntu 10.10 : 10.04 : 9.10 ]

ref post #1

only thing of note is that some connection managers rely on getting info about the device settings
as seen by the system , so therefore setting wvdial to use the correct port will overcome
what other connection managers or modem-managers can't do

alexfish

[dunbrokin]

hi

from the screen shot it looked as if you had a connection / the image is blurry

From what I gather your still looking for a solution

as a update from the other thread , there is a post where the device shows tttACM0

could see if there is dev serial ttyACM

can try

ls -al /dev/serial/by-id

if there is a listing at the end with ttyACM0 or others

then the connection path could be /dev/ttyACM0

with this info could try wvdial

but may need other info from the device : dial command , and or possible the APN

to find the APN's can have a look at this how to

How To : Mobile Broadband Connections [ Ubuntu 10.10 : 10.04 : 9.10 ]

ref post #1

only thing of note is that some connection managers rely on getting info about the device settings
as seen by the system , so therefore setting wvdial to use the correct port will overcome
what other connection managers or modem-managers can't do

alexfish

~$ ls -al /dev/serial/by-id
total 0
drwxr-xr-x 2 root root 80 2011-01-27 13:08 .
drwxr-xr-x 4 root root 80 2011-01-27 13:08 ..
lrwxrwxrwx 1 root root 13 2011-01-27 13:08 usb-Vodafone_K3805-z_C7986D8B72DFB07EF2FAE8645D14803D06F92E84-if01 -> ../../ttyACM0
lrwxrwxrwx 1 root root 13 2011-01-27 13:08 usb-Vodafone_K3805-z_C7986D8B72DFB07EF2FAE8645D14803D06F92E84-if03 -> ../../ttyACM1

However, I have no idea what this means or where I go from here.

[alexfish]

~$ ls -al /dev/serial/by-id
total 0
drwxr-xr-x 2 root root 80 2011-01-27 13:08 .
drwxr-xr-x 4 root root 80 2011-01-27 13:08 ..
lrwxrwxrwx 1 root root 13 2011-01-27 13:08 usb-Vodafone_K3805-z_C7986D8B72DFB07EF2FAE8645D14803D06F92E84-if01 -> ../../ttyACM0
lrwxrwxrwx 1 root root 13 2011-01-27 13:08 usb-Vodafone_K3805-z_C7986D8B72DFB07EF2FAE8645D14803D06F92E84-if03 -> ../../ttyACM1

However, I have no idea what this means or where I go from here.

can have a look here

Vodafone USB

RE;post #36 :: can post results back here

alexfish

[dunbrokin]

pj@pj-indulgence:~$ ls -al /dev/serial/by-id
total 0
drwxr-xr-x 2 root root 80 2011-01-28 12:43 .
drwxr-xr-x 4 root root 80 2011-01-28 12:43 ..
lrwxrwxrwx 1 root root 13 2011-01-28 12:43 usb-Vodafone_K3805-z_C7986D8B72DFB07EF2FAE8645D14803D06F92E84-if01 -> ../../ttyACM0
lrwxrwxrwx 1 root root 13 2011-01-28 12:43 usb-Vodafone_K3805-z_C7986D8B72DFB07EF2FAE8645D14803D06F92E84-if03 -> ../../ttyACM1
pj@pj-indulgence:~$ tr -s "\n" < /dev/ttyACM0
bash: /dev/ttyACM0: Device or resource busy
pj@pj-indulgence:~$

Thanks for your help....I really appreciate it.

[dunbrokin]

The light never comes on on my Vodem.....I am starting to think that this is a wasted effort....has anybody got this to work?