Page 6 of 6 FirstFirst ... 456
Results 51 to 55 of 55

Thread: 10.10 RNX-N250PC ralink chip rt3062 driver install need help

  1. #51
    Join Date
    Sep 2005
    Beans
    74

    Re: 10.10 RNX-N250PC ralink chip rt3062 driver install need help

    Hi

    Does anyone know how to stop the ralink driver spamming dmesg ?

    i'm getting lots of

    [ 1235.011512] rt28xx_get_wireless_stats --->
    [ 1235.011517] <--- rt28xx_get_wireless_stats
    [ 1241.012140] MediaState is connected
    [ 1241.012173] ==>rt_ioctl_giwmode(mode=2)
    [ 1241.012189] ==>rt_ioctl_giwfreq 6
    [ 1241.012226] rt28xx_get_wireless_stats --->
    [ 1241.012230] <--- rt28xx_get_wireless_stats

    (and I mean lots)

    is there a way to install modules with less/no debugging ?

  2. #52
    Join Date
    Oct 2007
    Beans
    25

    Re: 10.10 RNX-N250PC ralink chip rt3062 driver install need help

    Chili if you are out there, I could really use your help. I know you will be able to solve this. I think it is trying to use the wrong driver. Here's some info.

    Code:
    $ uname -r
    2.6.38-8-generic
    Code:
    $ lspci -nn | grep 0280
    03:05.0 Network controller [0280]: Ralink corp. Device [1814:3062]
    Code:
    $ dmesg | grep -e rt2 -e rt3
    [    8.811346] rt3562sta: module license 'unspecified' taints kernel.
    [    8.820379] ===> rt2860_probe
    [    8.820408] rt2860 0000:03:05.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
    [    8.821677] @rt2860_probe MAC address: 00:1a:ef:1d:94:22
    [    8.821678] <=== rt2860_probe
    [    9.434123] <==== rt28xx_init, Status=0
    relavent output from ifconfig:
    Code:
    ra0       Link encap:Ethernet  HWaddr 00:1a:ef:1d:94:22  
              inet6 addr: fe80::21a:efff:fe1d:9422/64 Scope:Link
              UP BROADCAST MULTICAST  MTU:1500  Metric:1
              RX packets:4 errors:0 dropped:0 overruns:0 frame:0
              TX packets:42 errors:0 dropped:0 overruns:0 carrier:0
              collisions:0 txqueuelen:1000 
              RX bytes:536 (536.0 B)  TX bytes:0 (0.0 B)
              Interrupt:20
    relavent output from iwconfig:
    Code:
    ra0       Ralink STA  ESSID:""  Nickname:"RT3562STA"
              Mode:Auto  Frequency=2.412 GHz  Access Point: Not-Associated   
              Bit Rate:1 Mb/s   
              RTS thr:off   Fragment thr:off
              Link Quality=10/100  Signal level:0 dBm  Noise level:0 dBm
              Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
              Tx excessive retries:0  Invalid misc:0   Missed beacon:0
    Code:
    $ tail -10 /etc/modules
    # /etc/modules: kernel modules to load at boot time.
    #
    # This file contains the names of kernel modules that should be loaded
    # at boot time, one per line. Lines beginning with "#" are ignored.
    
    lp
    rtc
    rt3562sta
    Code:
    $ tail -6  /etc/modprobe.d/blacklist.conf
    
    # for rosewill wiresless adapter
    blacklist rt2800pci
    blacklist rt2x00lib
    blacklist rt2x00pci
    blacklist rt2800lib
    Code:
    $ iwlist scanning
    lo        Interface doesn't support scanning.
    
    eth0      Interface doesn't support scanning.
    
    ra0       Scan completed :
              Cell 01 - Address: 00:1F:90:D4:BC:74
                        Protocol:802.11b/g
                        ESSID:""
                        Mode:Managed
                        Frequency:2.437 GHz (Channel 6)
                        Quality:44/100  Signal level:-72 dBm  Noise level:-77 dBm
                        Encryption key:on
                        Bit Rates:54 Mb/s
                        IE: WPA Version 1
                            Group Cipher : CCMP
                            Pairwise Ciphers (1) : CCMP
                            Authentication Suites (1) : PSK
                        IE: IEEE 802.11i/WPA2 Version 1
                            Group Cipher : CCMP
                            Pairwise Ciphers (1) : CCMP
                            Authentication Suites (1) : PSK
    Code:
    $ lspci -v | tail -8
    
    03:05.0 Network controller: Ralink corp. Device 3062
    	Subsystem: Ralink corp. Device 3062
    	Flags: bus master, slow devsel, latency 32, IRQ 20
    	Memory at ff500000 (32-bit, non-prefetchable) [size=64K]
    	Capabilities: <access denied>
    	Kernel driver in use: rt2860
    	Kernel modules: rt3562sta, rt2800pci
    Code:
    $ modinfo rt2800pci | grep 3062
    alias:          pci:v00001814d00003062sv*sd*bc*sc*i*
    Should it be using rt2860? I would think it should use rt3562sta. My only idea would be to blacklist rt2860 as well.

    When I try to connect to my wireless network it just hangs and then fails to connect. I feel like I am close though.

  3. #53
    Join Date
    Oct 2007
    Beans
    25

    Re: 10.10 RNX-N250PC ralink chip rt3062 driver install need help

    Woo Hoo! I rebooted and re-entered my wireless credentials and it is working.

    Sorry for the unessecary post.

  4. #54
    Join Date
    Aug 2005
    Location
    South Carolina, USA
    Beans
    23,312
    Distro
    Ubuntu 17.04 Zesty Zapus

    Re: 10.10 RNX-N250PC ralink chip rt3062 driver install need help

    The module rt2860sta is not correct for your device:
    Code:
    chili@LAPTOP60:~$ modinfo rt2860sta | grep 3062
    chili@LAPTOP60:~$
    There is no result from this command because the rt2860sta module doesn't claim your device. Verify that it's not loaded:
    Code:
    lsmod | grep rt2
    I see only three problems.
    ra0 Scan completed :
    Cell 01 - Address: 00:1F:90:D4:BC:74
    Protocol:802.11b/g
    ESSID:""
    Mode:Managed
    Frequency:2.437 GHz (Channel 6)
    Quality:44/100 Signal level:-72 dBm Noise level:-77 dBm
    Encryption key:on
    Bit Rates:54 Mb/s
    IE: WPA Version 1
    Group Cipher : CCMP
    Pairwise Ciphers (1) : CCMP
    Authentication Suites (1) : PSK
    IE: IEEE 802.11i/WPA2 Version 1
    Group Cipher : CCMP
    Pairwise Ciphers (1) : CCMP
    Authentication Suites (1) : PSK
    I don't know if it's Network Manager, wpa_supplicant or your driver, but you will probably never connect to a hidden ESSID. As well, you will have great difficulty connecting to a weak signal.

    Do you have the option to set a non-hidden ESSID? Is there a strength setting in your router? Is it dialed up to the maximum? Please see attached.

    Finally, can you choose WPA2 only and not mixed WPA and WPA2 mode?
    Attached Images Attached Images
    "Oh, Ubuntu, you are my favorite Linux-based operating system" --Dr. Sheldon Cooper, Ph.D.

  5. #55
    Join Date
    Aug 2005
    Location
    South Carolina, USA
    Beans
    23,312
    Distro
    Ubuntu 17.04 Zesty Zapus

    Re: 10.10 RNX-N250PC ralink chip rt3062 driver install need help

    Quote Originally Posted by jbrid View Post
    Woo Hoo! I rebooted and re-entered my wireless credentials and it is working.

    Sorry for the unessecary post.
    Awesome! Glad it's working.
    "Oh, Ubuntu, you are my favorite Linux-based operating system" --Dr. Sheldon Cooper, Ph.D.

Page 6 of 6 FirstFirst ... 456

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •