Hi,
Since yesterday, after the latest kernel upgrade from 2.6.31-24 to -25, I have no wireless networking anymore. Now I have been left in the dark before by Ubuntu so I'm not saying I'm surprised here
just glad there is always this marvellous community that has answers most of the time...
My wireless is a ZyXel ZyAIR G-100 PCMCIA card which worked out of the box on 9.10 but since Ubuntu 10.04 I had to install linux-backports-modules-wireless-lucid-generic which was actually a meta package depending on linux-backports-modules-wireless-2.6.32-24-generic
Along with the kernel update, linux-backports-modules-wireless-lucid-generic upgraded to version 2.6.32.25.27 but it currently (suddenly?) depends on linux-backports-modules-compat-wireless-2.6.34-2.6.32-25-generic... (notice the 2 differences!)
The old linux-backports-modules-wireless is still installed but I guess the new linux-backports-modules-compat-wireless is being used now. I notice that there is a linux-backports-modules-wireless-2.6.35-lucid-generic available but it conflicts with linux-backports-modules-wireless-lucid-generic so I hesitate to install that one and loose my networking completely (I have no eth available, just wlan!) like I have had before...
DMESG when I boot with kernel 2.6.32-24 (and working wlan0):
DMESG when I boot with kernel 2.6.32-25 (and no wlan0):Code:... [ 27.740133] pcmcia_socket pcmcia_socket0: pccard: CardBus card inserted into slot 0 [ 27.740201] pci 0000:03:00.0: reg 10 32bit mmio: [0x000000-0x001fff] [ 27.740291] pci 0000:03:00.0: supports D1 D2 [ 27.740295] pci 0000:03:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 27.740302] pci 0000:03:00.0: PME# disabled [ 27.821823] cfg80211: Calling CRDA to update world regulatory domain [ 27.870641] cfg80211: World regulatory domain updated: [ 27.870647] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 27.870651] (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 27.870655] (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 27.870658] (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 27.870661] (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 27.870664] (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 27.905196] p54pci 0000:03:00.0: enabling device (0000 -> 0002) [ 27.905212] p54pci 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 27.905229] p54pci 0000:03:00.0: setting latency timer to 64 [ 27.932591] phy0: p54 detected a LM86 firmware [ 27.932596] p54: rx_mtu reduced from 3240 to 2376 [ 27.932600] phy0: FW rev 2.13.12.0 - Softmac protocol 5.9 [ 27.932603] phy0: cryptographic accelerator WEP:YES, TKIP:YES, CCMP:YES ... [ 28.817832] phy0: hwaddr 00:a0:c5:92:72:f4, MAC:isl3890 RF:Frisbee [ 28.827085] phy0: Selected rate control algorithm 'minstrel' [ 28.828114] Registered led device: p54-phy0::assoc [ 28.828140] Registered led device: p54-phy0::tx [ 28.828163] Registered led device: p54-phy0::rx [ 28.828189] Registered led device: p54-phy0::radio [ 28.828201] p54pci 0000:03:00.0: is registered as 'phy0' ...
Anybody an idea how to get my wireless card working again under 2.6.32-25 and up?Code:... [ 27.490116] pcmcia_socket pcmcia_socket0: pccard: CardBus card inserted into slot 0 [ 27.490185] pci 0000:03:00.0: reg 10 32bit mmio: [0x000000-0x001fff] [ 27.490273] pci 0000:03:00.0: supports D1 D2 [ 27.490276] pci 0000:03:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 27.490283] pci 0000:03:00.0: PME# disabled ...
Thanks![]()



Adv Reply


Bookmarks