Hi there. Long talk made short, problem im facing with looks like this:
Tried manual (static) ip settings also, with no luck and different duplex speed options with autoneg off/on, but seems like its somekind driver problem?! (Sadly, I`m new to linux and not understanding all of this yet).
cable/router/n.card are tested and OK - were working under Windows XP with no problems.
This terminal output is made with livecd (ubuntu 8.10 - also tested 6.10, 8.06, centOS 5.2 - as installed or livecd - everytime same problem. So now, I want to get network working with livecd`s before installing anything again on hdd. Windows hdd was removed that time.)
Terminal output:
Code:# ubuntu@ubuntu:~$ dmesg | grep 8139 [ 3.631942] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004) [ 4.280361] 8139cp 0000:01:07.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip [ 4.280368] 8139cp 0000:01:07.0: Try the "8139too" driver instead. [ 4.284116] 8139too Fast Ethernet driver 0.9.28 [ 4.284423] 8139too 0000:01:07.0: PCI INT A -> Link[APC3] -> GSI 18 (level, high) -> IRQ 18 [ 4.285237] eth0: RealTek RTL8139 at 0xc400, 00:40:95:30:62:5e, IRQ 18 [ 4.285240] eth0: Identified 8139 chip type 'RTL-8139C' # ubuntu@ubuntu:~$ lspci | grep 8139 01:07.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) # ubuntu@ubuntu:~$ lsmod | grep 8139 8139too 31616 0 8139cp 27520 0 mii 13440 2 8139too,8139cp # ubuntu@ubuntu:~$ lspci -vv 00:00.0 Host bridge: nVidia Corporation nForce2 IGP2 (rev c1) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Region 0: Memory at e0000000 (32-bit, prefetchable) [size=128M] Capabilities: <access denied> Kernel driver in use: agpgart-nvidia Kernel modules: nvidia-agp 00:00.1 RAM memory: nVidia Corporation nForce2 Memory Controller 0 (rev c1) Subsystem: nVidia Corporation Device 0c17 Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:00.2 RAM memory: nVidia Corporation nForce2 Memory Controller 4 (rev c1) Subsystem: nVidia Corporation Device 0c17 Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:00.3 RAM memory: nVidia Corporation nForce2 Memory Controller 3 (rev c1) Subsystem: nVidia Corporation Device 0c17 Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:00.4 RAM memory: nVidia Corporation nForce2 Memory Controller 2 (rev c1) Subsystem: nVidia Corporation Device 0c17 Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:00.5 RAM memory: nVidia Corporation nForce2 Memory Controller 5 (rev c1) Subsystem: nVidia Corporation Device 0c17 Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:01.0 ISA bridge: nVidia Corporation nForce2 ISA Bridge (rev a4) Subsystem: nVidia Corporation Device 0c11 Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Capabilities: <access denied> 00:01.1 SMBus: nVidia Corporation nForce2 SMBus (MCP) (rev a2) Subsystem: nVidia Corporation Device 0c11 Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin A routed to IRQ 11 Region 0: I/O ports at e400 [size=32] Capabilities: <access denied> Kernel driver in use: nForce2_smbus Kernel modules: i2c-nforce2 00:02.0 USB Controller: nVidia Corporation nForce2 USB Controller (rev a4) (prog-if 10) Subsystem: nVidia Corporation Device 0c11 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (750ns min, 250ns max) Interrupt: pin A routed to IRQ 21 Region 0: Memory at eb001000 (32-bit, non-prefetchable) [size=4K] Capabilities: <access denied> Kernel driver in use: ohci_hcd Kernel modules: ohci-hcd 00:02.1 USB Controller: nVidia Corporation nForce2 USB Controller (rev a4) (prog-if 10) Subsystem: nVidia Corporation Device 0c11 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (750ns min, 250ns max) Interrupt: pin B routed to IRQ 20 Region 0: Memory at eb002000 (32-bit, non-prefetchable) [size=4K] Capabilities: <access denied> Kernel driver in use: ohci_hcd Kernel modules: ohci-hcd 00:02.2 USB Controller: nVidia Corporation nForce2 USB Controller (rev a4) (prog-if 20) Subsystem: nVidia Corporation Device 0c11 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (750ns min, 250ns max) Interrupt: pin C routed to IRQ 22 Region 0: Memory at eb003000 (32-bit, non-prefetchable) [size=256] Capabilities: <access denied> Kernel driver in use: ehci_hcd Kernel modules: ehci-hcd 00:08.0 PCI bridge: nVidia Corporation nForce2 External PCI Bridge (rev a3) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=32 I/O behind bridge: 0000c000-0000cfff Memory behind bridge: ea000000-eaffffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr+ DiscTmrStat- DiscTmrSERREn- Kernel modules: shpchp 00:09.0 IDE interface: nVidia Corporation nForce2 IDE (rev a2) (prog-if 8a [Master SecP PriP]) Subsystem: Device f0de:05b2 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (750ns min, 250ns max) Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [disabled] [size=8] Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [disabled] [size=1] Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [disabled] [size=8] Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [disabled] [size=1] Region 4: I/O ports at f000 [size=16] Capabilities: <access denied> Kernel driver in use: pata_amd Kernel modules: pata_amd 00:1e.0 PCI bridge: nVidia Corporation nForce2 AGP (rev c1) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 Bus: primary=00, secondary=02, subordinate=02, sec-latency=32 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: e8000000-e9ffffff Prefetchable memory behind bridge: c0000000-dfffffff Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Kernel modules: shpchp 01:06.0 Multimedia audio controller: C-Media Electronics Inc CM8738 (rev 10) Subsystem: C-Media Electronics Inc CM8738 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 (500ns min, 6000ns max) Interrupt: pin A routed to IRQ 17 Region 0: I/O ports at c000 [size=256] Capabilities: <access denied> Kernel driver in use: C-Media PCI Kernel modules: snd-cmipci 01:07.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Subsystem: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 (8000ns min, 16000ns max) Interrupt: pin A routed to IRQ 18 Region 0: I/O ports at c400 [size=256] Region 1: Memory at ea000000 (32-bit, non-prefetchable) [size=256] Capabilities: <access denied> Kernel driver in use: 8139too Kernel modules: 8139cp, 8139too 02:00.0 VGA compatible controller: ATI Technologies Inc RV350 AP [Radeon 9600] Subsystem: ATI Technologies Inc RV350 AP [Radeon 9600] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 (2000ns min), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 19 Region 0: Memory at c0000000 (32-bit, prefetchable) [size=256M] Region 1: I/O ports at d000 [size=256] Region 2: Memory at e9000000 (32-bit, non-prefetchable) [size=64K] [virtual] Expansion ROM at e8000000 [disabled] [size=128K] Capabilities: <access denied> Kernel modules: radeonfb 02:00.1 Display controller: ATI Technologies Inc RV350 AP [Radeon 9600] (Secondary) Subsystem: ATI Technologies Inc Device 4151 Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Region 0: Memory at d0000000 (32-bit, prefetchable) [disabled] [size=256M] Region 1: Memory at e9010000 (32-bit, non-prefetchable) [disabled] [size=64K] Capabilities: <access denied> # ubuntu@ubuntu:~$ ifconfig -a eth0 Link encap:Ethernet HWaddr 00:40:95:30:62:5e UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:18 Base address:0xc400 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:304 errors:0 dropped:0 overruns:0 frame:0 TX packets:304 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:20016 (20.0 KB) TX bytes:20016 (20.0 KB) pan0 Link encap:Ethernet HWaddr 32:45:ed:bd:84:2d BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
### edit ###
Today I tried Ubuntu 9,04 and got network working finaly!
# ubuntu@ubuntu:~$ sudo mii-tool eth0 -F 10baseT-FD
# ubuntu@ubuntu:~$ sudo rmmod 8139too
# ubuntu@ubuntu:~$ sudo modprobe 8139too
Adv Reply
Bookmarks