Search:

Type: Posts; User: s-bodet; Keyword(s):

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    257

    [kubuntu] Last Yakkety packages update

    Hi all,

    I'm running Yakkety and the last update broke lots of things :
    - mysqld still eating more than 100 MB of memory (known issue, tried several workarounds without success),
    - cannot launch...
  2. [SOLVED] Re: Problem at fixing the "ndiswrapper module not found" problem

    Hi,



    you probably don't have the right kernel header package.



    should correct this error message.
  3. Replies
    18
    Views
    2,551

    [ubuntu] Re: Networking - Forwarding Issues

    Hi,

    that should work, no need to enable NAT onto your Ubuntu server.

    What are the hosts onto the LAN ? What's their routing table ?

    Steve
  4. Replies
    1
    Views
    571

    Re: Forwarding data From ETH0 to BR0

    Since your virtual machines are in a RFC1918 address space (ie non routed over the Internet), you'll need to perform IP translation somewhere.
    I then notice the /32 on your eth0:0, it means you'll...
  5. Replies
    1
    Views
    354

    [ubuntu] Re: routing and forwarding problem

    Hi,

    it's a straightforward topology, it should work.
    You will need to masquerade if the upstream router has no entry for the eth2 subnet in its routing table.

    Steve
  6. Re: Make things work in spite of a bad router? Two vlans same hardware, no 802.1q

    From a pure TCP/IP prospective, both IP source and destination have no clue they're onto the same cable therefore packets should go through their local IP gateway (the AT&T gawteway).

    You should...
  7. Replies
    2
    Views
    1,530

    Re: two isp and iptables prerouting

    This command adds a default route in the main routing table.

    To stay consistent with your design, you would need the following commands :


    ip route add default via xx.yy.47.137 table uplink1...
  8. Replies
    6
    Views
    1,733

    Re: ubuntu router: ping works but not http

    It means your client sends IP packets with the DF bit set.
    Then the Cisco 2100 sends an ICMP T3,C4 when it needs to forward an IP packet larger than the MTU of the outgoing interface.

    I would...
  9. [ubuntu] Re: Proxy-arp settings for multiple network cards

    Hi,

    If you want the eth0 & eth1 IP subnets to access the Internet, you just need to enable SNAT in your server.
    Pretty sure Google will help :-)

    Steve
  10. [SOLVED] Re: VRRP not passing LDAPS traffic on port 636

    Hi,

    not sure that would work by default.

    A VRRP address is a very special address (there's no entry in /etc/network/interfaces for example). As such, a VRRP address has no direct access to the...
  11. Replies
    3,405
    Views
    328,595

    Sticky: Re: Welcome to the Forums - Introduce yourself here

    Hi All !

    Greetings from Europe ):P

    I'm Steve, leaving in France and working in the IT industry (switching/routing stuff).

    Crossed Linux a couple of years ago :P
    I like the Ubuntu distro...
  12. Replies
    12
    Views
    10,342

    Re: How to install Ndiswrapper

    Hi,

    I've been struggling against the AE2500 as well :-(

    The post here after

    http://ubuntuforums.org/showthread.php?t=1805830&p=11811107#post11811107

    was my starting point...
  13. Replies
    3
    Views
    416

    [ubuntu] Re: Routes Not Switching Back.

    Hi,

    until we don't know more on how you configured the routing stuff, it's not easy to help...

    How do you trigger the backup ?

    Steve
  14. Replies
    3
    Views
    808

    [ubuntu] Re: Network Between vLANs

    Assuming your interfaces are eth0 (10.10.200.254/24), eth1 (10.10.203.254/23), eth2 (10.10.206.254/24) correctly configured in /etc/network/interfaces

    1) Edit /etc/default/isc-dhcp-server to let...
Results 1 to 14 of 14