Broadcom BCM57785

[ksjenka]

I'm new to linux, so don't be really hard on me. I bought a new laptop - Acer Aspire v3-571g intel-corei3-3110M. I tried to install different linux distros: pear os, elementary os luna and ubuntu finally. In all cases it says "Connected" to my wired internet, but actually the internet isn't working. I really don't know what to. On my old Acer laptop installed Ubuntu and the internet works like a charm. Maybe I have to install ethernet drivers? Please, help me.
I set up outputs that I saw in other threads is most requested for help, but I'm not sure what those commands mean:



ifconfig
eth0 Link encap:Ethernet HWaddr b8:88:e3:a3:f6:25
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Interrupt:16


lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:218 errors:0 dropped:0 overruns:0 frame:0
TX packets:218 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:18634 (18.6 KB) TX bytes:18634 (18.6 KB)


wlan0 Link encap:Ethernet HWaddr 68:94:23:1e:e2:51
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)


sudo lshw -C network
[sudo] password for ksenia:
*-network
description: Ethernet interface
product: NetLink BCM57785 Gigabit Ethernet PCIe
vendor: Broadcom Corporation
physical id: 0
bus info: pci@0000:02:00.0
logical name: eth0
version: 10
serial: b8:88:e3:a3:f6:25
capacity: 1Gbit/s
width: 64 bits
clock: 33MHz
capabilities: pm msi msix pciexpress bus_master cap_list rom ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.128 firmware=sb latency=0 link=no multicast=yes port=twisted pair
resources: irq:16 memory:b3430000-b343ffff memory:b3440000-b344ffff memory:b3450000-b34507ff
*-network
description: Wireless interface
product: AR9462 Wireless Network Adapter
vendor: Atheros Communications Inc.
physical id: 0
bus info: pci@0000:03:00.0
logical name: wlan0
version: 01
serial: 68:94:23:1e:e2:51
width: 64 bits
clock: 33MHz
capabilities: pm msi pciexpress bus_master cap_list rom ethernet physical wireless
configuration: broadcast=yes driver=ath9k driverversion=3.8.0-19-generic firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11abgn
resources: irq:17 memory:b3500000-b357ffff memory:9fc00000-9fc0ffff




sudo lspci
00:00.0 Host bridge: Intel Corporation 3rd Gen Core processor DRAM Controller (rev 09)
00:01.0 PCI bridge: Intel Corporation Xeon E3-1200 v2/3rd Gen Core processor PCI Express Root Port (rev 09)
00:02.0 VGA compatible controller: Intel Corporation 3rd Gen Core processor Graphics Controller (rev 09)
00:14.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB xHCI Host Controller (rev 04)
00:16.0 Communication controller: Intel Corporation 7 Series/C210 Series Chipset Family MEI Controller #1 (rev 04)
00:1a.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #2 (rev 04)
00:1b.0 Audio device: Intel Corporation 7 Series/C210 Series Chipset Family High Definition Audio Controller (rev 04)
00:1c.0 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 1 (rev c4)
00:1c.1 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 2 (rev c4)
00:1d.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #1 (rev 04)
00:1f.0 ISA bridge: Intel Corporation HM77 Express Chipset LPC Controller (rev 04)
00:1f.2 SATA controller: Intel Corporation 7 Series Chipset Family 6-port SATA Controller [AHCI mode] (rev 04)
00:1f.3 SMBus: Intel Corporation 7 Series/C210 Series Chipset Family SMBus Controller (rev 04)
01:00.0 VGA compatible controller: NVIDIA Corporation GK107M [GeForce GT 640M] (rev a1)
02:00.0 Ethernet controller: Broadcom Corporation NetLink BCM57785 Gigabit Ethernet PCIe (rev 10)
02:00.1 SD Host controller: Broadcom Corporation NetXtreme BCM57765 Memory Card Reader (rev 10)
02:00.2 System peripheral: Broadcom Corporation Device 16be (rev 10)
02:00.3 System peripheral: Broadcom Corporation Device 16bf (rev 10)
03:00.0 Network controller: Atheros Communications Inc. AR9462 Wireless Network Adapter (rev 01)


lspci -nn | grep 0200
02:00.0 Ethernet controller [0200]: Broadcom Corporation NetLink BCM57785 Gigabit Ethernet PCIe [14e4:16b5] (rev 10)










Thanks to all who are helping people here:)

[praseodym]

Hi,

is the driver loaded?


lsmod
please also check:


cat /etc/network/interfaces
cat /etc/resolv.conf
route -n
Is wireless working? If yes, install this package and show additionally:


sudo apt-get install ethtool
sudo ethtool eth0

[ksjenka]

OK, that's the info I got:



lsmod
Module Size Used by
snd_hda_codec_hdmi 36913 1
snd_hda_codec_realtek 78399 1
parport_pc 28152 0
ppdev 17073 0
bnep 18036 2
rfcomm 42641 0
bluetooth 228619 10 bnep,rfcomm
joydev 17377 0
coretemp 13355 0
kvm_intel 132891 0
kvm 443165 1 kvm_intel
ghash_clmulni_intel 13259 0
cryptd 20373 1 ghash_clmulni_intel
acer_wmi 32467 0
sparse_keymap 13890 1 acer_wmi
snd_hda_intel 39619 3
snd_hda_codec 136453 3 snd_hda_codec_realtek,snd_hda_codec_hdmi,snd_hda_i ntel
snd_hwdep 13602 1 snd_hda_codec
snd_pcm 97451 3 snd_hda_codec_hdmi,snd_hda_codec,snd_hda_intel
snd_page_alloc 18710 2 snd_pcm,snd_hda_intel
snd_seq_midi 13324 0
snd_seq_midi_event 14899 1 snd_seq_midi
snd_rawmidi 30180 1 snd_seq_midi
uvcvideo 80847 0
snd_seq 61554 2 snd_seq_midi_event,snd_seq_midi
videobuf2_vmalloc 13056 1 uvcvideo
snd_seq_device 14497 3 snd_seq,snd_rawmidi,snd_seq_midi
videobuf2_memops 13202 1 videobuf2_vmalloc
videobuf2_core 40513 1 uvcvideo
snd_timer 29425 2 snd_pcm,snd_seq
videodev 129260 2 uvcvideo,videobuf2_core
nouveau 939088 0
arc4 12615 2
mac_hid 13205 0
i915 600351 3
microcode 22881 0
ath9k 149924 0
ath9k_common 14055 1 ath9k
ath9k_hw 413680 2 ath9k_common,ath9k
ath 23827 3 ath9k_common,ath9k,ath9k_hw
mxm_wmi 13021 1 nouveau
ttm 83187 1 nouveau
mac80211 606457 1 ath9k
wmi 19070 3 acer_wmi,mxm_wmi,nouveau
video 19390 3 i915,acer_wmi,nouveau
drm_kms_helper 49394 2 i915,nouveau
drm 286313 6 ttm,i915,drm_kms_helper,nouveau
cfg80211 510937 3 ath,ath9k,mac80211
psmouse 95870 0
serio_raw 13215 0
snd 68876 16 snd_hda_codec_realtek,snd_hwdep,snd_timer,snd_hda_ codec_hdmi,snd_pcm,snd_seq,snd_rawmidi,snd_hda_cod ec,snd_hda_intel,snd_seq_device
i2c_algo_bit 13413 2 i915,nouveau
mei 41158 0
soundcore 12680 1 snd
lpc_ich 17061 0
lp 17759 0
parport 46345 3 lp,ppdev,parport_pc
sdhci_pci 18590 0
sdhci 32522 1 sdhci_pci
tg3 153796 0
ahci 25731 4
libahci 31364 1 ahci
ptp 18621 1 tg3
pps_core 14080 1 ptp




cat /etc/network/interfaces
# interfaces(5) file used by ifup(8) and ifdown(8)
auto lo
iface lo inet loopback


cat /etc/resolv.conf
# Dynamic resolv.conf(5) file for glibc resolver(3) generated by resolvconf(8)
# DO NOT EDIT THIS FILE BY HAND -- YOUR CHANGES WILL BE OVERWRITTEN
nameserver 127.0.1.1


route -n
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
0.0.0.0 172.16.31.253 0.0.0.0 UG 0 0 0 eth0
169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 eth0
172.16.16.0 0.0.0.0 255.255.240.0 U 1 0 0 eth0




sudo apt-get install ethtool
[sudo] password for ksenia:
Reading package lists... Done
Building dependency tree
Reading state information... Done
Package ethtool is not available, but is referred to by another package.
This may mean that the package is missing, has been obsoleted, or
is only available from another source


E: Package 'ethtool' has no installation candidate




I don't have a wireless connection, I only can see the users in list that are connected to wi-fi network. But to be sure I did the last command.

[praseodym]

Which Ubuntu version is it? Please show


uname -a
lsb_release -a

[ksjenka]

Here:



uname -a
Linux ksenia-Aspire-V3-571G 3.8.0-19-generic #29-Ubuntu SMP Wed Apr 17 18:16:28 UTC 2013 x86_64 x86_64 x86_64 GNU/Linux


ksenia@ksenia-Aspire-V3-571G:~$ lsb_release -a
No LSB modules are available.
Distributor ID: Ubuntu
Description: Ubuntu 13.04
Release: 13.04
Codename: raring

[praseodym]

Download this package to "Downloads":

http://de.archive.ubuntu.com/ubuntu/pool/main/e/ethtool/ethtool_3.4.2-1_amd64.deb

Installation via:


sudo dpkg -i ~/Downloads/*.deb
sudo ethtool eth0

[ksjenka]

I assume I had to connect my cable to the new laptop in order to check the last command, which I did (sorry I'm saying those stupid things):



sudo ethtool eth0
[sudo] password for ksenia:
Settings for eth0:
Supported ports: [ TP ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Half 1000baseT/Full
Supported pause frame use: No
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Half 1000baseT/Full
Advertised pause frame use: Symmetric
Advertised auto-negotiation: Yes
Link partner advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
Link partner advertised pause frame use: Symmetric
Link partner advertised auto-negotiation: Yes
Speed: 100Mb/s
Duplex: Full
Port: Twisted Pair
PHYAD: 1
Transceiver: internal
Auto-negotiation: on
MDI-X: on
Supports Wake-on: g
Wake-on: g
Current message level: 0x000000ff (255)
drv probe link timer ifdown ifup rx_err tx_err
Link detected: yes

[ksjenka]

For additional information: I'm currently typing all of my posts on my old laptop, where this wired connection is working; I'm also downloading from there, then I'm putting info on my flash usb; and also all of the output from my new laptop I put on this flash drive in .txt, go back to this old laptop in order to write here.

[praseodym]

Try to deactivate the auto-negotiation of the card:


sudo ethtool -s eth0 speed 100 autoneg off

[ksjenka]

Nope, nothing's changed:(

[praseodym]

nameserver 127.0.1.1
This should read:

nameserver 127.0.0.1

gksudo gedit /etc/resolv.conf
Change the file, save, close the editor and restart the network (or reboot):


sudo /etc/init.d/networking restart

[ksjenka]

It says:



gksudo gedit /etc/resolv.conf
The program 'gksudo' is currently not installed. You can install it by typing:
sudo apt-get install gksu

I tried to use sudo:



ksenia@ksenia-Aspire-V3-571G:~$ sudo gedit /etc/resolv.conf
[sudo] password for ksenia:


(gedit:2518): IBUS-WARNING **: The owner of /home/ksenia/.config/ibus/bus is not root!


But after I changed the file, reboot and opened it again it's still:




nameserver 127.0.1.1


and of course the internet doesn't work still...
How do I install gksudo?

[ksjenka]

Even though I downloaded the .deb package of gksu(http://packages.ubuntu.com/raring/amd64/gksu/download), installed and I had also to download and install this - http://packages.ubuntu.com/raring/amd64/libgksu2-0/download, because there was a message in terminal about this lib - I didn't get the positive result - I changed the resolv.conf file, rebooted and again nothing - and the changes in that file didn't take place - it is:

nameserver 127.0.1.1

instead of: nameserver 127.0.0.1

@praseodym, please help me

[praseodym]

Uninstall this one:


sudo apt-get remove --purge resolvconf
and reboot. If there is nothing inside afterwards, then:


echo -e "nameserver 8.8.8.8\nnameserver 8.8.4.4" | sudo tee -a /etc/resolv.conf
sudo /etc/init.d/networking restart

[ksjenka]

After I executed first command - I couldn't reboot normally, it froze, so I pushed the power off button to force its turning off. When I was booting there was a message (I didn't quite remembered all numbers) somewhat like this :



[8.833423] usb 1-1.1 script descritor 0 read error [-22]
unable to detect USB 1 port



When I did this:



sudo gedit /etc/resolv.conf



it took to that file, where was this:




# Generated by NetworkManager
nameserver 127.0.1.1




So, do I need to execute your last commands?

[chili555]

I would love to see:
dmesg | grep -e tg3 -e eth0 > ksj.txtFind the file ksj.txt in your user directory and transfer and post it as before.

[ksjenka]

Sorry for my stupidity: I executed the command and nothing's happened:




ksenia@ksenia-Aspire-V3-571G:~$ dmesg | grep -e tg3 -e eth0 > ksj.txt
ksenia@ksenia-Aspire-V3-571G:~$





Then in home directory I found ksj.txt file (the cable to internet was plugged in to my new laptop):



[ 1.269249] tg3.c:v3.128 (December 03, 2012)
[ 1.296018] tg3 0000:02:00.0 eth0: Tigon3 [partno(BCM57785) rev 57785100] (PCI Express) MAC address b8:88:e3:a3:f6:25
[ 1.296023] tg3 0000:02:00.0 eth0: attached PHY is 57765 (10/100/1000Base-T Ethernet) (WireSpeed[1], EEE[1])
[ 1.296026] tg3 0000:02:00.0 eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
[ 1.296029] tg3 0000:02:00.0 eth0: dma_rwctrl[00000001] dma_mask[64-bit]
[ 8.126735] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 11.199686] tg3 0000:02:00.0: irq 46 for MSI/MSI-X
[ 11.199692] tg3 0000:02:00.0: irq 47 for MSI/MSI-X
[ 11.199695] tg3 0000:02:00.0: irq 48 for MSI/MSI-X
[ 11.199698] tg3 0000:02:00.0: irq 49 for MSI/MSI-X
[ 11.199701] tg3 0000:02:00.0: irq 50 for MSI/MSI-X
[ 11.389997] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 11.390288] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 13.147946] tg3 0000:02:00.0 eth0: Link is up at 100 Mbps, full duplex
[ 13.147951] tg3 0000:02:00.0 eth0: Flow control is on for TX and on for RX
[ 13.147954] tg3 0000:02:00.0 eth0: EEE is disabled
[ 13.147972] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 128.772020] tg3 0000:02:00.0 eth0: Link is down
[ 132.822240] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 3021.199871] tg3 0000:02:00.0 eth0: Link is up at 100 Mbps, full duplex
[ 3021.199877] tg3 0000:02:00.0 eth0: Flow control is on for TX and on for RX
[ 3021.199881] tg3 0000:02:00.0 eth0: EEE is disabled
[ 3021.199901] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready



Hope it'll help to help me, lol:)

[ksjenka]

I read this article - http://havingnoclue.wordpress.com/2012/03/25/lan-working-on-acer-aspire-5750-6872-laptop-with-ubuntu-10-04/
and tried to install the driver, but there was issues:
1. In HOME I created "Ethernet" directory where I extracted linux-3.129d.zip
2. I extracted tg3-3.129d.tar.gz in Ethernet/Sever/Linux/Driver folder and there appeared "tg3-3.129d" folder
3. Opened a terminal and did the following:



ksenia@ksenia-Aspire-V3-571G:~$ cd Ethernet/Server/Linux/Driver/
ksenia@ksenia-Aspire-V3-571G:~/Ethernet/Server/Linux/Driver$ cd tg3-3.129d
ksenia@ksenia-Aspire-V3-571G:~/Ethernet/Server/Linux/Driver/tg3-3.129d$ make
sh makeflags.sh /lib/modules/3.8.0-19-generic/build > tg3_flags.h
make -C /lib/modules/3.8.0-19-generic/build SUBDIRS=/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d modules
make[1]: Entering directory `/usr/src/linux-headers-3.8.0-19-generic'
CC [M] /home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.o
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:288:23: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘__devinitdata’
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:11377:23: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘tg3_timer_init’
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:14766:23: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘tg3_get_eeprom_size’
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:14800:23: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘tg3_get_nvram_size’
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:14833:23: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘tg3_get_nvram_info’
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:14884:23: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘tg3_nvram_get_pagesize’
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:14911:23: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘tg3_get_5752_nvram_info’
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:14952:23: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘tg3_get_5755_nvram_info’
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:15008:23: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘tg3_get_5787_nvram_info’
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:15046:23: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘tg3_get_5761_nvram_info’
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:15121:23: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘tg3_get_5906_nvram_info’
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:15128:23: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘tg3_get_57780_nvram_info’
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:15201:23: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘tg3_get_5717_nvram_info’
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:15279:23: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘tg3_get_5720_nvram_info’
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:15421:23: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘tg3_nvram_init’
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:15492:52: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘__devinitdata’
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:15556:42: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘tg3_lookup_by_subsys’
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:15570:23: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘tg3_get_eeprom_hw_cfg’
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:15783:22: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘tg3_ape_otp_read’
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:15816:22: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘tg3_issue_otp_command’
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:15839:22: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘tg3_read_otp_phycfg’
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:15865:23: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘tg3_phy_init_link_config’
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:15892:22: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘tg3_phy_probe’
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:16011:23: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘tg3_read_vpd’
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:16132:22: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘tg3_fw_img_is_valid’
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:16145:23: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘tg3_read_bc_ver’
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:16197:23: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘tg3_read_hwsb_ver’
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:16213:23: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘tg3_read_sb_ver’
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:16268:23: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘tg3_read_mgmtfw_ver’
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:16320:23: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘tg3_probe_ncsi’
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:16336:23: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘tg3_read_dash_ver’
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:16361:23: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘tg3_read_otp_ver’
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:16386:23: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘tg3_read_fw_ver’
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:16442:35: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘tg3_find_peer’
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:16470:23: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘tg3_detect_asic_rev’
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:16579:22: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘tg3_get_invariants’
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:17436:22: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘tg3_get_device_address’
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:17517:22: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘tg3_calc_dma_bndry’
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:17658:22: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘tg3_do_test_dma’
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:17747:22: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘tg3_test_dma’
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:17943:23: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘tg3_init_bufmgr_config’
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:17999:25: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘tg3_phy_string’
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:18038:25: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘tg3_bus_string’
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:18074:23: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘tg3_init_coal’
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:18105:22: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘tg3_init_one’
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:18625:23: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘tg3_remove_one’
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:18939:12: error: ‘tg3_init_one’ undeclared here (not in a function)
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:18940:2: error: implicit declaration of function ‘__devexit_p’ [-Werror=implicit-function-declaration]
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:18940:25: error: ‘tg3_remove_one’ undeclared here (not in a function)
In file included from /home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.h:13:0,
from /home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:118:
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3_compat.h:969:14: warning: ‘print_mac’ defined but not used [-Wunused-function]
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:548:12: warning: ‘tg3_read32’ defined but not used [-Wunused-function]
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:579:12: warning: ‘tg3_read_indirect_reg32’ defined but not used [-Wunused-function]
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:621:12: warning: ‘tg3_read_indirect_mbox’ defined but not used [-Wunused-function]
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:674:12: warning: ‘tg3_read32_mbox_5906’ defined but not used [-Wunused-function]
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:679:13: warning: ‘tg3_write32_mbox_5906’ defined but not used [-Wunused-function]
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:747:13: warning: ‘tg3_ape_lock_init’ defined but not used [-Wunused-function]
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:1623:12: warning: ‘tg3_mdio_init’ defined but not used [-Wunused-function]
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:1739:13: warning: ‘tg3_mdio_fini’ defined but not used [-Wunused-function]
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:11246:13: warning: ‘tg3_timer’ defined but not used [-Wunused-function]
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:11436:13: warning: ‘tg3_reset_task’ defined but not used [-Wunused-function]
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:14524:27: warning: ‘tg3_ethtool_ops’ defined but not used [-Wunused-variable]
/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.c:16558:13: warning: ‘tg3_10_100_only_device’ defined but not used [-Wunused-function]
cc1: some warnings being treated as errors
make[2]: *** [/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d/tg3.o] Error 1
make[1]: *** [_module_/home/ksenia/Ethernet/Server/Linux/Driver/tg3-3.129d] Error 2
make[1]: Leaving directory `/usr/src/linux-headers-3.8.0-19-generic'
make: *** [default] Error 2




I didn't execute commands:


insmod tg3.ko

and


make install

because of those errors above.
What did I do wrong?? I don't know how to install it, the README.TXT file instructions apparently aren't enough for me, I'm a total noob.:(

[chili555]

because of those errors above.
What did I do wrong?? I don't know how to install it, the README.TXT file instructions apparently aren't enough for me, I'm a total noob.:(The article was written for Ubuntu 10.04. The package was written for kernel 2.6.xx. You have Ubuntu 13.04 and kernel 3.8. The package has too many dis-similarities from your sleek modern kernel.

Let's try to dig even deeper. Please hook up the ethernet cable. Shut down completely (not reboot). Start the computer and let it try to connect. After a few minutes, run and post:
cat /var/log/syslog | grep -e tg3 -e etwork -e eth0 > ksj2.txtThe file is likely to be quite long so paste it here and give us the link: http://paste.ubuntu.com/

[ksjenka]

OK, I did it, the file is here - http://paste.ubuntu.com/5947511/

[chili555]

Joining mDNS multicast group on interface eth0.IPv4 with address 172.16.26.226.
Aug 4 19:12:58 ksenia-Aspire-V3-571G avahi-daemon[766]: New relevant interface eth0.IPv4 for mDNS.
Aug 4 19:12:58 ksenia-Aspire-V3-571G avahi-daemon[766]: Registering new address record for 172.16.26.226 on eth0.IPv4.So it connected just fine??
ping -c3 8.8.8.8
ifconfigIt looks like you have a dnsmasq issue, but, nonetheless, eth0 connects! Yes? No?

--------

More information: https://bugs.launchpad.net/ubuntu/+source/network-manager/+bug/1048430


Peter: the issue here is that this "error" is expected: on the very first update after boot, dnsmasq will get spawned during the update phase, but is likely not going to be ready yet -- the update will "fail" and fallback to writing the dns names directly to resolv.conf, instead of writing 127.0.1.1 and using dnsmasq. Then when dnsmasq appears on the bus the update is re-tried, and should succeed.

[ksjenka]

Yes it connects immediately after I hook up the cable: message "Connected" appears, but browsers won't work and Software Center too - it says "Server not found" - that's the whole deal - the internet connection exists but there is no actual internet in the same time. I can't figure what's the problem.

[praseodym]

Check now:


cat /etc/resolv.conf
route -n
ping -c 2 $(route -n | grep UG | awk {'print $2'})
ping -c 2 www.ubuntuusers.de
ping -c 2 213.95.41.11

[ksjenka]

This is what I got:




cat /etc/resolv.conf
# Generated by NetworkManager
nameserver 127.0.1.1
ksenia@ksenia-Aspire-V3-571G:~$ route -n
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
0.0.0.0 172.16.31.253 0.0.0.0 UG 0 0 0 eth0
169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 eth0
172.16.16.0 0.0.0.0 255.255.240.0 U 1 0 0 eth0
ksenia@ksenia-Aspire-V3-571G:~$ ping -c 2 $(route -n | grep UG | awk {'print $2'})
PING 172.16.31.253 (172.16.31.253) 56(84) bytes of data.


--- 172.16.31.253 ping statistics ---
2 packets transmitted, 0 received, 100% packet loss, time 1007ms


ksenia@ksenia-Aspire-V3-571G:~$ ping -c 2 www.ubuntuusers.de
ping: unknown host www.ubuntuusers.de
ksenia@ksenia-Aspire-V3-571G:~$ ping -c 2 213.95.41.11
PING 213.95.41.11 (213.95.41.11) 56(84) bytes of data.


--- 213.95.41.11 ping statistics ---
2 packets transmitted, 0 received, 100% packet loss, time 999ms

[praseodym]

Go to the network-manager profile and change "Automatic (DHCP)" to "Automatic (DHCP), addresses only" and add


8.8.8.8, 8.8.4.4
in the DNS field. restart your network


sudo service network-manager restart

[ksjenka]

I did all of the above - the message is "Disconnected". Though, maybe I should point out that it wasn't "Automatic (DHCP)" it was "Manual", because I manually added all the ip, gateway,dns - see the screenshot - http://imgur.com/c1CO4Ka

[ksjenka]

Please, take a look at this output, maybe it'll help:




lshw -C network ; ip a ; tracepath ya.ru
WARNING: you should run this program as super-user.
*-network
description: Ethernet interface
product: NetLink BCM57785 Gigabit Ethernet PCIe
vendor: Broadcom Corporation
physical id: 0
bus info: pci@0000:02:00.0
logical name: eth0
version: 10
serial: b8:88:e3:a3:f6:25
size: 100Mbit/s
capacity: 1Gbit/s
width: 64 bits
clock: 33MHz
capabilities: bus_master cap_list rom ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.128 duplex=full firmware=sb ip=172.16.26.226 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s
resources: irq:16 memory:b3430000-b343ffff memory:b3440000-b344ffff memory:b3450000-b34507ff
*-network
description: Wireless interface
product: AR9462 Wireless Network Adapter
vendor: Atheros Communications Inc.
physical id: 0
bus info: pci@0000:03:00.0
logical name: wlan0
version: 01
serial: 68:94:23:1e:e2:51
width: 64 bits
clock: 33MHz
capabilities: bus_master cap_list rom ethernet physical wireless
configuration: broadcast=yes driver=ath9k driverversion=3.8.0-19-generic firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11abgn
resources: irq:17 memory:b3500000-b357ffff memory:9fc00000-9fc0ffff
WARNING: output may be incomplete or inaccurate, you should run this program as super-user.
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP qlen 1000
link/ether b8:88:e3:a3:f6:25 brd ff:ff:ff:ff:ff:ff
inet 172.16.26.226/20 brd 172.16.31.255 scope global eth0
inet6 fe80::ba88:e3ff:fea3:f625/64 scope link
valid_lft forever preferred_lft forever
3: wlan0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN qlen 1000
link/ether 68:94:23:1e:e2:51 brd ff:ff:ff:ff:ff:ff
gethostbyname2: Resolver internal error



ksenia@ksenia-Aspire-V3-571G:~$ sudo lshw -C network ; ip a ; tracepath ya.ru
[sudo] password for ksenia:
*-network
description: Ethernet interface
product: NetLink BCM57785 Gigabit Ethernet PCIe
vendor: Broadcom Corporation
physical id: 0
bus info: pci@0000:02:00.0
logical name: eth0
version: 10
serial: b8:88:e3:a3:f6:25
size: 100Mbit/s
capacity: 1Gbit/s
width: 64 bits
clock: 33MHz
capabilities: pm msi msix pciexpress bus_master cap_list rom ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.128 duplex=full firmware=sb ip=172.16.26.226 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s
resources: irq:16 memory:b3430000-b343ffff memory:b3440000-b344ffff memory:b3450000-b34507ff
*-network
description: Wireless interface
product: AR9462 Wireless Network Adapter
vendor: Atheros Communications Inc.
physical id: 0
bus info: pci@0000:03:00.0
logical name: wlan0
version: 01
serial: 68:94:23:1e:e2:51
width: 64 bits
clock: 33MHz
capabilities: pm msi pciexpress bus_master cap_list rom ethernet physical wireless
configuration: broadcast=yes driver=ath9k driverversion=3.8.0-19-generic firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11abgn
resources: irq:17 memory:b3500000-b357ffff memory:9fc00000-9fc0ffff
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP qlen 1000
link/ether b8:88:e3:a3:f6:25 brd ff:ff:ff:ff:ff:ff
inet 172.16.26.226/20 brd 172.16.31.255 scope global eth0
inet6 fe80::ba88:e3ff:fea3:f625/64 scope link
valid_lft forever preferred_lft forever
3: wlan0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN qlen 1000
link/ether 68:94:23:1e:e2:51 brd ff:ff:ff:ff:ff:ff
gethostbyname2: Resolver internal error

[ksjenka]

I solved the problem, I just had to change my MAC-address on new laptop:)))))

[ksjenka]

I really wanna say thank you really much @praseodym and @chili555, you rock!:))))

[chili555]

Glad it's working! Have fun!