Problems with USP driver "Atmel Corp. AVR ISP mkII"

[ritchie-w]

Hello,

I have a problem with the driver USB driver "Atmel Corp. AVR ISP mkII".

When is connect the programmer, I will have the following usb device availiable.



Bus 002 Device 008: ID 03eb:2104 Atmel Corp. AVR ISP mkII


But after access this device once, via "avrdude" or a VMWare system using the AVR Studio, the driver is gone. I tried this with the kUbuntu 32Bit/64bit Version.

Any help for me ?

R.

[ritchie-w]

Hi,

does somebody may know, what this means, because this messages where log in the system log during trying to connect to the USB programmer.



05.12.2011 22:17:14 XXX kernel [ 2706.061782] usb 2-1.2: new full speed USB device number 9 using ehci_hcd
05.12.2011 22:17:29 XXX kernel [ 2721.090828] usb 2-1.2: device descriptor read/64, error -110
05.12.2011 22:17:44 XXX kernel [ 2736.223606] usb 2-1.2: device descriptor read/64, error -110
05.12.2011 22:17:44 XXX kernel [ 2736.399090] usb 2-1.2: new full speed USB device number 10 using ehci_hcd
05.12.2011 22:17:59 XXX kernel [ 2751.428123] usb 2-1.2: device descriptor read/64, error -110
05.12.2011 22:18:14 XXX kernel [ 2766.560901] usb 2-1.2: device descriptor read/64, error -110
05.12.2011 22:18:15 XXX kernel [ 2766.736398] usb 2-1.2: new full speed USB device number 11 using ehci_hcd
05.12.2011 22:18:25 XXX kernel [ 2777.114542] usb 2-1.2: device not accepting address 11, error -110
05.12.2011 22:18:25 XXX kernel [ 2777.186462] usb 2-1.2: new full speed USB device number 12 using ehci_hcd
05.12.2011 22:18:35 XXX kernel [ 2787.564661] usb 2-1.2: device not accepting address 12, error -110
05.12.2011 22:18:35 XXX kernel [ 2787.564830] hub 2-1:1.0: unable to enumerate USB device on port 2


The following rule file exists for usb devices

/etc/udev/rules.d/80-usbprog.rules
with the following content:


ATTR{idVendor}=="03eb", ATTR{idProduct}=="2104", GROUP="plugdev", MODE="0660" # AVRISP mkII


The command "$ lsusb -s 0013 -vv" gives the following output


Bus 002 Device 013: ID 03eb:2104 Atmel Corp. AVR ISP mkII
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 255 Vendor Specific Class
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x03eb Atmel Corp.
idProduct 0x2104 AVR ISP mkII
bcdDevice 2.00
iManufacturer 1
iProduct 2
iSerial 3
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 32
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Device Status: 0x0000
(Bus Powered)



Any hint to get rid of this problem ?

The programmer works fine with a normal windows XP installation and AVR Studio 5.

I am using the latest kernel version:
Linux XXX 3.0.0-13-generic #22-Ubuntu SMP Wed Nov 2 13:27:26 UTC 2011 x86_64 x86_64 x86_64 GNU/Linux


Greating R.

[ritchie-w]

The supllier told me, that it is a problem of the product.

The "Diamex ALL-AVR Programmer adapter for AVR Controller" does not support the linux OS up to now.

There will work on it (maybe).

Thanks
R.

[Spirail]

This is NOT solved here.
I have had this working on Ubuntu before. But that was last year. I have since upgraded to 11.10 and no such luck these days.


Wish i remember what i did (if that is still valid)

[ritchie-w]

Hi,

you are right, this "Atmel Corp. AVR ISP mkII" is still not working inside my VMware.

I try to use the programmer inside a VMWare under (guest OS) windows, which is running on kubuntu 11.10 (as host os).


I thought after a BIOS Update of the programmer is will work, but it didn't.

Regards
R.