[SOLVED] 10.04 unable to set resolutions on non-EDID monitor [Archive]

View Full Version : [SOLVED] 10.04 unable to set resolutions on non-EDID monitor

jdneate

September 23rd, 2011, 02:03 PM

I would be grateful for any help ..........

I did a clean install of 10.04.03 from an alternate cd last week. It works fine but I have been trying to get the monitor to work at higher resolution - 1024x768.

The computer is old - the driver card is nVidia ( but I have not installed the recommended driver ); the monitor is an old Proview CY565 which I suspect does not have EDID.

I have listed my efforts below ....

1 I printed out the display/driver configurations as suggested by MAFoLLfen....
--------------------------------------------------------------------------
jdn@jdneate:~$ sudo hwinfo--monitor 26: None 00.0: 10000 Monitor
[Created at fb.71]
Unique ID: rdCR.EY_qmtb9YY0
Hardware Class: monitor
Model: "Generic Monitor"
Vendor: "Generic"
Device: "Monitor"
Resolution: 640x480@60Hz
Driver Info #0:
Max. Resolution: 640x480
Vert. Sync Range: 50-70 Hz
Hor. Sync Range: 31-33 kHz
Config Status: cfg=new, avail=yes, need=no, active=unknown

jdn@jdneate:~$ sudo hwinfo --framebuffer
02: None 00.0: 11001 VESA Framebuffer
[Created at bios.464]
Unique ID: rdCR.9X2tz5+Fif6
Hardware Class: framebuffer
Model: "NVidia NV11 (GeForce2) Board"
Vendor: "NVidia Corporation"
Device: "NV11 (GeForce2) Board"
SubVendor: "NVidia"
SubDevice:
Revision: "Chip Rev B2"
Memory Size: 32 MB
Memory Range: 0xe0000000-0xe1ffffff (rw)
Mode 0x0300: 640x400 (+640), 8 bits
Mode 0x0301: 640x480 (+640), 8 bits
Mode 0x0303: 800x600 (+800), 8 bits
Mode 0x0305: 1024x768 (+1024), 8 bits
Mode 0x0307: 1280x1024 (+1280), 8 bits
Mode 0x030e: 320x200 (+640), 16 bits
Mode 0x030f: 320x200 (+1280), 24 bits
Mode 0x0311: 640x480 (+1280), 16 bits
Mode 0x0312: 640x480 (+2560), 24 bits
Mode 0x0314: 800x600 (+1600), 16 bits
Mode 0x0315: 800x600 (+3200), 24 bits
Mode 0x0317: 1024x768 (+204, 16 bits
Mode 0x0318: 1024x768 (+4096), 24 bits
Mode 0x031a: 1280x1024 (+2560), 16 bits
Mode 0x0330: 320x200 (+320), 8 bits
Mode 0x0331: 320x400 (+320), 8 bits
Mode 0x0332: 320x400 (+640), 16 bits
Mode 0x0333: 320x400 (+1280), 24 bits
Mode 0x0334: 320x240 (+320), 8 bits
Mode 0x0335: 320x240 (+640), 16 bits
Mode 0x0336: 320x240 (+1280), 24 bits
Mode 0x033d: 640x400 (+1280), 16 bits
Mode 0x033e: 640x400 (+2560), 24 bits
Mode 0x0345: 1600x1200 (+1600), 8 bits
Mode 0x0346: 1600x1200 (+3200), 16 bits
Config Status: cfg=new, avail=yes, need=no, active=unknown
jdn@jdneate:~$
--------------------------------------------------------------------------
2 The Proview monitor has max resolution of 1024x768 at 75Hz.
Horizontal frequency 31 - 60 kHz
Vertical frequency 60 - 75 Hz

--------------------------------------------------------------------------

3 I listed files in /etc/X11/ but no xorg.conf shown. So I attempted to generate one without success

--------------------------------------------------------------------------
jdn@jdneate:~$ sudo Xorg -configure
[sudo] password for jdn:

Fatal server error:
Server is already active for display 0
If this server is no longer running, remove /tmp/.X0-lock
and start again.
Please consult the The X.Org Foundation support
at http://wiki.x.org
for help.

ddxSigGiveUp: Closing log
jdn@jdneate:~$
--------------------------------------------------------------------------

4 I have used xrandr to try to change resolution temporarily. I can change between resolutions which are already configured but I can not configure a new resolution ( addmode )

--------------------------------------------------------------------------
admin@jdneate:~$ sudo xrandr
[sudo] password for admin:
Screen 0: minimum 640 x 480, current 800 x 600, maximum 800 x 600
default connected 800x600+0+0 0mm x 0mm
800x600 61.0*
640x480 60.0
admin@jdneate:~$ cvt 1024 768
# 1024x768 59.92 Hz (CVT 0.79M3) hsync: 47.82 kHz; pclk: 63.50 MHz
Modeline "1024x768_60.00" 63.50 1024 1072 1176 1328 768 771 775 798 -hsync +vsync
admin@jdneate:~$ xrandr --newmode "1024x768_60.00" 63.50 1024 1072 1176 1328 768 771 775 798 -hsync +vsync
admin@jdneate:~$ xrandr --addmode default 1024x768
xrandr: cannot find mode "1024x768"
admin@jdneate:~$ xrandr --output default --mode 1024x768
xrandr: cannot find mode 1024x768
admin@jdneate:~$

--------------------------------------------------------------------------

5 I have tried stopping X and generating an xorg.config using CTRL-ALT-F1

sudo service gdm stop
sudo X -configure

At which point there is a screen full of text ending in "number of created screens does not match the number of detected devices; configuration failed.

--------------------------------------------------------------------------

6 I think the following is the relevant part of the kern.log

--------------------------------------------------------------------------

jdneate kernel: [ 12.721117] uvcvideo: Found UVC 1.00 device <unnamed> (046d:0825)
Sep 23 09:13:58 jdneate kernel: [ 12.767741] type=1505 audit(1316765637.880:2): operation="profile_load" pid=589 name="/sbin/dhclient3"
Sep 23 09:13:58 jdneate kernel: [ 12.799853] type=1505 audit(1316765637.912:3): operation="profile_load" pid=589 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
Sep 23 09:13:58 jdneate kernel: [ 12.801171] type=1505 audit(1316765637.916:4): operation="profile_load" pid=589 name="/usr/lib/connman/scripts/dhclient-script"
Sep 23 09:13:58 jdneate kernel: [ 12.821016] input: UVC Camera (046d:0825) as /devices/pci0000:00/0000:00:1e.0/0000:02:01.2/usb1/1-2/1-2:1.0/input/input6
Sep 23 09:13:58 jdneate kernel: [ 12.821185] usbcore: registered new interface driver uvcvideo
Sep 23 09:13:58 jdneate kernel: [ 12.821193] USB Video Class driver (v0.1.0)
Sep 23 09:13:58 jdneate kernel: [ 13.054419] pci 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
Sep 23 09:13:58 jdneate kernel: [ 13.098503] [drm] nouveau 0000:01:00.0: Detected an NV10 generation card (0x011100b2)
Sep 23 09:13:58 jdneate kernel: [ 13.098580] [drm] Initialized nouveau 0.0.15 20090420 for 0000:01:00.0 on minor 0
Sep 23 09:13:58 jdneate kernel: [ 13.127135] vga16fb: initializing
Sep 23 09:13:58 jdneate kernel: [ 13.127152] vga16fb: mapped to 0xc00a0000
Sep 23 09:13:58 jdneate kernel: [ 13.127770] fb0: VGA16 VGA frame buffer device
Sep 23 09:13:59 jdneate kernel: [ 13.969351] type=1505 audit(1316765639.084:5): operation="profile_load" pid=729 name="/usr/share/gdm/guest-session/Xsession"
Sep 23 09:13:59 jdneate kernel: [ 14.071660] type=1505 audit(1316765639.184:6): operation="profile_replace" pid=733 name="/sbin/dhclient3"
Sep 23 09:13:59 jdneate kernel: [ 14.101876] type=1505 audit(1316765639.216:7): operation="profile_replace" pid=733 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
Sep 23 09:13:59 jdneate kernel: [ 14.102439] type=1505 audit(1316765639.216:8): operation="profile_replace" pid=733 name="/usr/lib/connman/scripts/dhclient-script"
Sep 23 09:13:59 jdneate kernel: [ 14.153119] ENS1371 0000:02:02.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
Sep 23 09:13:59 jdneate kernel: [ 14.469396] type=1505 audit(1316765639.584:9): operation="profile_load" pid=737 name="/usr/bin/evince"
Sep 23 09:13:59 jdneate kernel: [ 14.512996] Console: switching to colour frame buffer device 80x30
Sep 23 09:13:59 jdneate kernel: [ 14.523686] eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
Sep 23 09:13:59 jdneate kernel: [ 14.600226] type=1505 audit(1316765639.716:10): operation="profile_load" pid=737 name="/usr/bin/evince-previewer"
Sep 23 09:13:59 jdneate kernel: [ 14.698587] type=1505 audit(1316765639.812:11): operation="profile_load" pid=737 name="/usr/bin/evince-thumbnailer"
Sep 23 09:14:00 jdneate kernel: [ 15.009947] 3:3:1: cannot set freq 16000 to ep 0x86
Sep 23 09:14:01 jdneate kernel: [ 16.050663] 3:3:2: cannot set freq 24000 to ep 0x86
Sep 23 09:14:02 jdneate kernel: [ 17.048343] 3:3:3: cannot set freq 32000 to ep 0x86
Sep 23 09:14:03 jdneate kernel: [ 18.048136] 3:3:4: cannot set freq 48000 to ep 0x86
Sep 23 09:14:03 jdneate kernel: [ 18.066617] usbcore: registered new interface driver snd-usb-audio
Sep 23 09:14:03 jdneate kernel: [ 18.550109] [TTM] Zone kernel: Available graphics memory: 440310 kiB.
Sep 23 09:14:03 jdneate kernel: [ 18.550117] [TTM] Zone highmem: Available graphics memory: 772058 kiB.
Sep 23 09:14:03 jdneate kernel: [ 18.550147] [drm] nouveau 0000:01:00.0: 32 MiB VRAM
Sep 23 09:14:03 jdneate kernel: [ 18.550270] agpgart-intel 0000:00:00.0: AGP 2.0 bridge
Sep 23 09:14:03 jdneate kernel: [ 18.550299] agpgart-intel 0000:00:00.0: putting AGP V2 device into 4x mode
Sep 23 09:14:03 jdneate kernel: [ 18.550329] pci 0000:01:00.0: putting AGP V2 device into 4x mode
Sep 23 09:14:03 jdneate kernel: [ 18.550369] [drm] nouveau 0000:01:00.0: 64 MiB GART (aperture)
Sep 23 09:14:03 jdneate kernel: [ 18.550692] [drm] nouveau 0000:01:00.0: Allocating FIFO number 0
Sep 23 09:14:03 jdneate kernel: [ 18.551205] [drm] nouveau 0000:01:00.0: nouveau_channel_alloc: initialised FIFO 0
Sep 23 09:14:03 jdneate kernel: [ 18.551232] [drm] nouveau 0000:01:00.0: PFIFO_CACHE_ERROR - Ch 0/0 Mthd 0x0180 Data 0x80000006
Sep 23 09:14:03 jdneate kernel: [ 18.551244] [drm] nouveau 0000:01:00.0: PFIFO_CACHE_ERROR - Ch 0/0 Mthd 0x0180 Data 0x80000006
Sep 23 09:14:03 jdneate kernel: [ 18.551602] [drm] nouveau 0000:01:00.0: nouveau_channel_free: freeing fifo 0
Sep 23 09:14:03 jdneate kernel: [ 18.552383] [drm] nouveau 0000:01:00.0: RAMHT entry not found. ch=0, handle=0x8000000e
Sep 23 09:14:03 jdneate kernel: [ 18.552818] [drm] nouveau 0000:01:00.0: RAMHT entry not found. ch=0, handle=0x80000006
Sep 23 09:14:03 jdneate kernel: [ 18.553250] [drm] nouveau 0000:01:00.0: RAMHT entry not found. ch=0, handle=0x80000004
Sep 23 09:14:03 jdneate kernel:

--------------------------------------------------------------------------

I gather that 10.04 has "Kernel Mode Setting" - Suspending/Modifying this sounds frightening so I was hoping to permanently fix some xrandr commands in the start configuration but ...............

Any help greatly welcomed bearing in mind I am not too techy

realzippy

September 23rd, 2011, 02:36 PM

Try a basic xorg.conf with monitor data added:

gksudo gedit /etc/X11/xorg.conf

paste in:

Section "Device"
Identifier "Configured Video Device"
Driver "nouveau"
EndSection

Section "Monitor"
Identifier "Configured Monitor"
HorizSync 31-60
VertRefresh 56-76
EndSection

Section "Screen"
Identifier "Default Screen"
Monitor "Configured Monitor"
Device "Configured Video Device"
EndSection

jdneate

September 23rd, 2011, 07:08 PM

MAFoElffen

September 23rd, 2011, 08:07 PM

Hi realzippy --- thanks for the interest .... as I said I am not that techy but have crafted an xorg based on your reply and one which worked with the monitor on 8.04. As I said, i am not that techy ( although my techiness has grown significantly in the last two weeks )

I would be grateful if you could cast your eyes over the following for any obvious errors ....

Section "Device"
Identifier "Configured Video Device"
Driver "nouveau"
EndSection

Section "Monitor"
Identifier "Configured Monitor"
HorizSync 31-60
VertRefresh 60-75
# 1024x768 59.92 Hz (CVT 0.79M3) hsync: 47.82 kHz; pclk: 63.50 MHz
Modeline "1024x768_60.00" 63.50 1024 1072 1176 1328 768 771 775 798 -hsync +vsync
# 800x600 59.86 Hz (CVT 0.48M3) hsync: 37.35 kHz; pclk: 38.25 MHz
Modeline "800x600_60.00" 38.25 800 832 912 1024 600 603 607 624 -hsync +vsync
# 640x480 59.38 Hz (CVT 0.31M3) hsync: 29.69 kHz; pclk: 23.75 MHz
Modeline "640x480_60.00" 23.75 640 664 720 800 480 483 487 500 -hsync +vsync
Gamma 1.0

EndSection

Section "Screen"
Identifier "Default Screen"
Monitor "Configured Monitor"
Device "Configured Video Device"
Defaultdepth 24
Subsection "Display"
Depth 24
Virtual 1024 768
Modes "1024x768@60" "800x600@60" "640x480@60"
EndSubSection
EndSection
What is the best way of trying it and the consequence if it doesn't work - I could delete the file but would I be able to get into the terminal to do this ?

Many thanks
Here's some EDID Instructions I wrote in my graphics sticky in Post #275 (http://ubuntuforums.org/showpost.php?p=10907238&postcount=275).

Look where your Mode declarations are in the Monitor Section above? What are highlighted is your "mode names." These are just ID or variable names and must be matched in spelling and case when you reference them... Keep this in mind.

Now look in the Monitor Section above and use the color coding to reference the respective modes. You have an "@" character for each instead of "_". What those characters should be to correct this is a space character... When I do it, I use a space (" ") there, so it matches up and is consistent with mode names that would be generated by a box that is connected to a monitor that stores EDID data. Look at this example:

Section "ServerLayout"
Identifier "layout1"
Screen "screen1"
EndSection

Section "Device"
Identifier "device1"
VendorName "nVidia Corporation"
BoardName "NVIDIA GeForce 6100 and later"
Driver "nvidia"
Option "DPMS" "false"
Option "DynamicTwinView" "false"
Option "AddARGBGLXVisuals"
EndSection

Section "Monitor"
Identifier "monitor1"
VendorName "PnP laptop"
ModelName "2036"
HorizSync 30-83
VertRefresh 55-75
Modeline "1280x1024 75.00" 138.54 1280 1368 1504 1728 1024 1025 1028 1069 -HSync +Vsync
Option "PreferredMode" "1280x1024 75.00"
EndSection

Section "Screen"
Identifier "screen1"
Device "device1"
Monitor "monitor1"
DefaultColorDepth 24
Subsection "Display"
Depth 24
Modes "1280x1024" "1024x768" "800x600" "640x480"
EndSubsection
EndSection

Section "ServerFlags"
Option "DontZap" "1"
AllowMouseOpenFail
EndSection

So yours should resemble:

Section "Device"
Identifier "Configured Video Device"
Driver "nouveau"
EndSection

Section "Monitor"
Identifier "Configured Monitor"
HorizSync 31-60
VertRefresh 60-75
Modeline "1024x768 60.00" 63.50 1024 1072 1176 1328 768 771 775 798 -hsync +vsync
Modeline "800x600 60.00" 38.25 800 832 912 1024 600 603 607 624 -hsync +vsync
Modeline "640x480 60.00" 23.75 640 664 720 800 480 483 487 500 -hsync +vsync
Option "PreferredMode" "1024x768 60.00"
Gamma 1.0
EndSection

Section "Screen"
Identifier "Default Screen"
Monitor "Configured Monitor"
Device "Configured Video Device"
Defaultdepth 24
Subsection "Display"
Depth 24
Virtual 1024 768
Modes "1024x768" "800x600" "640x480"
EndSubSection
EndSection
After you sent your info... You do know that the Xorg NV driver supports your card, right? And since Ubuntu version 11.04, the Ubuntu Additional Drivers > Nouveau Experiment 3D driver for Nvidia is one of the best drivers I've tested for the older Legacy NVidia Cards!!! You have other options...

jdneate

September 23rd, 2011, 09:08 PM

Thanks for comments ...... I am away tomorrow. So I will try it on Sunday and see what happens.

jdneate

September 25th, 2011, 12:49 PM

Well I have just tried it and (sadly) it comes back with an error message at start up .... Ubuntu is running in low graphics mode. the following errors were encountered. You may need to update your configuration to solve this

(EE) (drm) KMS not enabled
(EE) no devices detected.

This is the /etc/X11/xorg.conf

spe@jdneate:~$ cat /etc/X11/xorg.conf
Section "Device"
Identifier "Configured Video Device"
Driver "nouveau"
EndSection

Section "Monitor"
Identifier "Configured Monitor"
HorizSync 31-60
VertRefresh 60-75
Modeline "1024x768 60.00" 63.50 1024 1072 1176 1328 768 771 775 798 -hsync +vsync
Modeline "800x600 60.00" 38.25 800 832 912 1024 600 603 607 624 -hsync +vsync
Modeline "640x480 60.00" 23.75 640 664 720 800 480 483 487 500 -hsync +vsync
Option "PreferredMode" "1024x768 60.00"
Gamma 1.0

EndSection

Section "Screen"
Identifier "Default Screen"
Monitor "Configured Monitor"
Device "Configured Video Device"
Defaultdepth 24
Subsection "Display"
Depth 24
Virtual 1024 768
Modes "1024x768 60.00" "800x600 60.00" "640x480 60.00"
EndSubSection
EndSection
spe@jdneate:~$

-------------------------------------------------------------------

Note - I had "finger trouble" in creating the xorg.conf file and didn't notice that I had typed gksudo gedit /etc/X11.xorg.conf and created it in there. I corrected my mistake by deleting the contents of this folder but it would not allow me to delete the file completely.

------------------------------------------------------------------------------------

Any advice gratefully received !!!!!!!

jdneate

September 25th, 2011, 01:03 PM

Forgot to mention in above post

System>Preferences>Monitor>Resolutions only shows the two lower resolutions but not the 1024x768.

I also tried Modes line in the xorg.conf with just the resolution excluding the "60.0" frequency.

realzippy

September 25th, 2011, 01:20 PM

1.The nouveau driver does not support modelines (afaik)
2.You seem to have disabled KMS.Did you edit "nomodeset" somewhere ?

jdneate

September 25th, 2011, 01:55 PM

Hi Realzippy

1 The nouveau driver does not support modelines (afaik) ----- what is the significance ??? If it doesn't should I replace "nouveau" by "default" in the "device" section of the xorg.conf ?
2 I specified NOMODESET to run the alternate CD when loading the system. I haven't edited it (as far as I know !).

Thanks

realzippy

September 25th, 2011, 02:15 PM

Hi jdneate,
the nouveau driver should be best choice for your card.
We could go on with that....but:
...as MAFoElffen suggested:
...since Ubuntu version 11.04, the Ubuntu Additional Drivers > Nouveau Experimental 3D driver...
might be worth a test.
(afaik it is nouveau/gallium)
Is that "experimental driver" offered in your system?
Can you check this out 1rst?

jdneate

September 25th, 2011, 02:22 PM

Hi realzippy
I had a quick play before i got your reply. I replaced "nouveau" by "default" in the driver section.

Error message on start up different ..

EE failed to load module "default" (module does not exist,0)

I will replace "default" by "experimental" and try again.
EE no drivers available.

realzippy

September 25th, 2011, 02:31 PM

Wait,
can't you have (please!!) a look at "additional drivers" before
you continue to edit xorg.conf randomly?
(which makes no sense...)

jdneate

September 25th, 2011, 02:37 PM

Tried "experimental driver" and " experimental" in the xorg.conf but driver not recognised message on restart.

jdneate

September 25th, 2011, 02:40 PM

Just picked up this message .... apologies for my lack of knowledge but how do I find whether I have the "additional drivers" ?? Thanks for your guidance

realzippy

September 25th, 2011, 02:45 PM

When installing the experimental driver via "additional drivers" you
should need no xorg.conf.
I do not know if a xorg.conf will "disturb" the experimental driver.
So can you please do the following (and anything else)? :

sudo mv /etc/X11/xorg.conf /etc/X11/xorg.conf.old
Then uninstall the experimental driver via additional drivers
(if you have not already).
Then reboot.
After reboot,post output from

cat /var/log/Xorg.0.log

Please try nothing until I have answered then.

realzippy

September 25th, 2011, 02:48 PM

Just picked up this message .... apologies for my lack of knowledge but how do I find whether I have the "additional drivers" ?? Thanks for your guidance

run in terminal

jockey-gtk

A window should open offering drivers...

jdneate

September 25th, 2011, 02:50 PM

Hi Realzippy

Apologies --- but what do you mean by this

"Then uninstall the experimental driver via additional drivers
(if you have not already)."

Thanks

realzippy

September 25th, 2011, 02:58 PM

I thought you already had tried the experimental driver offered in additional driver.

Ok,let's start again (from the beginning) step-by-step:

Open a terminal,run:

jockey-gtk

What happens?

jdneate

September 25th, 2011, 03:11 PM

Realzippy

This Xorg.0.log from administration>log file viewer

----------------------------------------------------------------------------

X.Org X Server 1.7.6
Release Date: 2010-03-17
X Protocol Version 11, Revision 0
Build Operating System: Linux 2.6.24-27-server i686 Ubuntu
Current Operating System: Linux jdneate 2.6.32-33-generic #72-Ubuntu SMP Fri Jul 29 21:08:37 UTC 2011 i686
Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.32-33-generic root=UUID=f5596863-aaea-4446-b6db-40e3bc0947ab ro nomodeset quiet splash
Build Date: 08 March 2011 08:22:50AM
xorg-server 2:1.7.6-2ubuntu7.6 (For technical support please see http://www.ubuntu.com/support)
Current version of pixman: 0.16.4
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Sun Sep 25 15:00:26 2011
(==) Using config directory: "/usr/lib/X11/xorg.conf.d"
(==) No Layout section. Using the first Screen section.
(==) No screen section available. Using defaults.
(**) |-->Screen "Default Screen Section" (0)
(**) | |-->Monitor "<default monitor>"
(==) No monitor specified for screen "Default Screen Section".
Using a default monitor configuration.
(==) Automatically adding devices
(==) Automatically enabling devices
(WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist.
Entry deleted from font path.
(==) FontPath set to:
/usr/share/fonts/X11/misc,
/usr/share/fonts/X11/100dpi/:unscaled,
/usr/share/fonts/X11/75dpi/:unscaled,
/usr/share/fonts/X11/Type1,
/usr/share/fonts/X11/100dpi,
/usr/share/fonts/X11/75dpi,
/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType,
built-ins
(==) ModulePath set to "/usr/lib/xorg/extra-modules,/usr/lib/xorg/modules"
(II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
(II) Loader magic: 0x81f1e80
(II) Module ABI versions:
X.Org ANSI C Emulation: 0.4
X.Org Video Driver: 6.0
X.Org XInput driver : 7.0
X.Org Server Extension : 2.0
(++) using VT number 7

(--) PCI:*(0:1:0:0) 10de:0111:10b0:0001 nVidia Corporation NV11DDR [GeForce2 MX200] rev 178, Mem @ 0xec000000/16777216, 0xe0000000/134217728, BIOS @ 0x????????/65536
(II) Open ACPI successful (/var/run/acpid.socket)
(II) LoadModule: "extmod"
(II) Loading /usr/lib/xorg/modules/extensions/libextmod.so
(II) Module extmod: vendor="X.Org Foundation"
compiled for 1.7.6, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "dbe"
(II) Loading /usr/lib/xorg/modules/extensions/libdbe.so
(II) Module dbe: vendor="X.Org Foundation"
compiled for 1.7.6, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "glx"
(II) Loading /usr/lib/xorg/modules/extensions/libglx.so
(II) Module glx: vendor="X.Org Foundation"
compiled for 1.7.6, module version = 1.0.0
ABI class: X.Org Server Extension, version 2.0
(==) AIGLX enabled
(II) Loading extension GLX
(II) LoadModule: "record"
(II) Loading /usr/lib/xorg/modules/extensions/librecord.so
(II) Module record: vendor="X.Org Foundation"
compiled for 1.7.6, module version = 1.13.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension RECORD
(II) LoadModule: "dri"
(II) Loading /usr/lib/xorg/modules/extensions/libdri.so
(II) Module dri: vendor="X.Org Foundation"
compiled for 1.7.6, module version = 1.0.0
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension XFree86-DRI
(II) LoadModule: "dri2"
(II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
(II) Module dri2: vendor="X.Org Foundation"
compiled for 1.7.6, module version = 1.1.0
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DRI2
(==) Matched nouveau as autoconfigured driver 0
(==) Matched nv as autoconfigured driver 1
(==) Matched vesa as autoconfigured driver 2
(==) Matched fbdev as autoconfigured driver 3
(==) Assigned the driver to the xf86ConfigLayout
(II) LoadModule: "nouveau"
(II) Loading /usr/lib/xorg/modules/drivers/nouveau_drv.so
(II) Module nouveau: vendor="X.Org Foundation"
compiled for 1.7.6, module version = 0.0.15
Module class: X.Org Video Driver
ABI class: X.Org Video Driver, version 6.0
(II) LoadModule: "nv"
(II) Loading /usr/lib/xorg/modules/drivers/nv_drv.so
(II) Module nv: vendor="X.Org Foundation"
compiled for 1.7.3.901, module version = 2.1.15
Module class: X.Org Video Driver
ABI class: X.Org Video Driver, version 6.0
(II) LoadModule: "vesa"
(II) Loading /usr/lib/xorg/modules/drivers/vesa_drv.so
(II) Module vesa: vendor="X.Org Foundation"
compiled for 1.7.6, module version = 2.3.0
Module class: X.Org Video Driver
ABI class: X.Org Video Driver, version 6.0
(II) LoadModule: "fbdev"
(II) Loading /usr/lib/xorg/modules/drivers/fbdev_drv.so
(II) Module fbdev: vendor="X.Org Foundation"
compiled for 1.7.6, module version = 0.4.1
ABI class: X.Org Video Driver, version 6.0
(II) NOUVEAU driver Date: Wed Feb 10 18:43:39 2010 +0100
(II) NOUVEAU driver for NVIDIA chipset families :
RIVA TNT (NV04)
RIVA TNT2 (NV05)
GeForce 256 (NV10)
GeForce 2 (NV11, NV15)
GeForce 4MX (NV17, NV18)
GeForce 3 (NV20)
GeForce 4Ti (NV25, NV28)
GeForce FX (NV3x)
GeForce 6 (NV4x)
GeForce 7 (G7x)
GeForce 8 (G8x)
(II) NOUVEAU driver Date: Wed Feb 10 18:43:39 2010 +0100
(II) NOUVEAU driver for NVIDIA chipset families :
RIVA TNT (NV04)
RIVA TNT2 (NV05)
GeForce 256 (NV10)
GeForce 2 (NV11, NV15)
GeForce 4MX (NV17, NV18)
GeForce 3 (NV20)
GeForce 4Ti (NV25, NV28)
GeForce FX (NV3x)
GeForce 6 (NV4x)
GeForce 7 (G7x)
GeForce 8 (G8x)
(II) VESA: driver for VESA chipsets: vesa
(II) FBDEV: driver for framebuffer: fbdev
(II) Primary Device is: PCI 01@00:00:0
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 8, (OK)
drmOpenByBusid: Searching for BusID pci:0000:01:00.0
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 8, (OK)
drmOpenByBusid: drmOpenMinor returns 8
drmOpenByBusid: drmGetBusid reports pci:0000:01:00.0
(II) [drm] nouveau interface version: 0.0.15
(EE) [drm] KMS not enabled
(WW) Falling back to old probe method for fbdev
(II) Loading sub module "fbdevhw"
(II) LoadModule: "fbdevhw"
(II) Loading /usr/lib/xorg/modules/linux/libfbdevhw.so
(II) Module fbdevhw: vendor="X.Org Foundation"
compiled for 1.7.6, module version = 0.0.2
ABI class: X.Org Video Driver, version 6.0
(II) Loading sub module "vbe"
(II) LoadModule: "vbe"
(II) Loading /usr/lib/xorg/modules/libvbe.so
(II) Module vbe: vendor="X.Org Foundation"
compiled for 1.7.6, module version = 1.1.0
ABI class: X.Org Video Driver, version 6.0
(II) Loading sub module "int10"
(II) LoadModule: "int10"
(II) Loading /usr/lib/xorg/modules/libint10.so
(II) Module int10: vendor="X.Org Foundation"
compiled for 1.7.6, module version = 1.0.0
ABI class: X.Org Video Driver, version 6.0
(II) VESA(0): initializing int10
(II) VESA(0): Primary V_BIOS segment is: 0xc000
(II) VESA(0): VESA BIOS detected
(II) VESA(0): VESA VBE Version 3.0
(II) VESA(0): VESA VBE Total Mem: 32768 kB
(II) VESA(0): VESA VBE OEM: NVidia
(II) VESA(0): VESA VBE OEM Software Rev: 3.17
(II) VESA(0): VESA VBE OEM Vendor: NVidia Corporation
(II) VESA(0): VESA VBE OEM Product: NV11 (GeForce2) Board
(II) VESA(0): VESA VBE OEM Product Rev: Chip Rev B2
(II) VESA(0): Creating default Display subsection in Screen section
"Default Screen Section" for depth/fbbpp 24/32
(==) VESA(0): Depth 24, (--) framebuffer bpp 32
(==) VESA(0): RGB weight 888
(==) VESA(0): Default visual is TrueColor
(==) VESA(0): Using gamma correction (1.0, 1.0, 1.0)
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"
(II) Module "ddc" already built-in
(II) VESA(0): VESA VBE DDC supported
(II) VESA(0): VESA VBE DDC Level none
(II) VESA(0): VESA VBE DDC transfer in appr. 0 sec.
(II) VESA(0): VESA VBE DDC read failed
(II) VESA(0): VESA VBE PanelID read failed
(II) VESA(0): Searching for matching VESA mode(s):
Mode: 100 (640x400)
ModeAttributes: 0x39f
WinAAttributes: 0x7
WinBAttributes: 0x0
WinGranularity: 64
WinSize: 64
WinASegment: 0xa000
WinBSegment: 0x0
WinFuncPtr: 0xc000956a
BytesPerScanline: 640
XResolution: 640
YResolution: 400
XCharSize: 8
YCharSize: 16
NumberOfPlanes: 1
BitsPerPixel: 8
NumberOfBanks: 1
MemoryModel: 4
BankSize: 0
NumberOfImages: 15
RedMaskSize: 0
RedFieldPosition: 0
GreenMaskSize: 0
GreenFieldPosition: 0
BlueMaskSize: 0
BlueFieldPosition: 0
RsvdMaskSize: 0
RsvdFieldPosition: 0
DirectColorModeInfo: 0
PhysBasePtr: 0xe0000000
LinBytesPerScanLine: 640
BnkNumberOfImagePages: 15
LinNumberOfImagePages: 15
LinRedMaskSize: 0
LinRedFieldPosition: 0
LinGreenMaskSize: 0
LinGreenFieldPosition: 0
LinBlueMaskSize: 0
LinBlueFieldPosition: 0
LinRsvdMaskSize: 0
LinRsvdFieldPosition: 0
MaxPixelClock: 229500000
Mode: 101 (640x480)
ModeAttributes: 0x39f
WinAAttributes: 0x7
WinBAttributes: 0x0
WinGranularity: 64
WinSize: 64
WinASegment: 0xa000
WinBSegment: 0x0
WinFuncPtr: 0xc000956a
BytesPerScanline: 640
XResolution: 640
YResolution: 480
XCharSize: 8
YCharSize: 16
NumberOfPlanes: 1
BitsPerPixel: 8
NumberOfBanks: 1
MemoryModel: 4
BankSize: 0
NumberOfImages: 11
RedMaskSize: 0
RedFieldPosition: 0
GreenMaskSize: 0
GreenFieldPosition: 0
BlueMaskSize: 0
BlueFieldPosition: 0
RsvdMaskSize: 0
RsvdFieldPosition: 0
DirectColorModeInfo: 0
PhysBasePtr: 0xe0000000
LinBytesPerScanLine: 640
BnkNumberOfImagePages: 11
LinNumberOfImagePages: 11
LinRedMaskSize: 0
LinRedFieldPosition: 0
LinGreenMaskSize: 0
LinGreenFieldPosition: 0
LinBlueMaskSize: 0
LinBlueFieldPosition: 0
LinRsvdMaskSize: 0
LinRsvdFieldPosition: 0
MaxPixelClock: 229500000
Mode: 102 (800x600)
ModeAttributes: 0x31f
WinAAttributes: 0x7
WinBAttributes: 0x0
WinGranularity: 64
WinSize: 64
WinASegment: 0xa000
WinBSegment: 0x0
WinFuncPtr: 0xc000956a
BytesPerScanline: 100
XResolution: 800
YResolution: 600
XCharSize: 8
YCharSize: 16
NumberOfPlanes: 4
BitsPerPixel: 4
NumberOfBanks: 1
MemoryModel: 3
BankSize: 0
NumberOfImages: 15
RedMaskSize: 0
RedFieldPosition: 0
GreenMaskSize: 0
GreenFieldPosition: 0
BlueMaskSize: 0
BlueFieldPosition: 0
RsvdMaskSize: 0
RsvdFieldPosition: 0
DirectColorModeInfo: 0
PhysBasePtr: 0x0
LinBytesPerScanLine: 100
BnkNumberOfImagePages: 15
LinNumberOfImagePages: 15
LinRedMaskSize: 0
LinRedFieldPosition: 0
LinGreenMaskSize: 0
LinGreenFieldPosition: 0
LinBlueMaskSize: 0
LinBlueFieldPosition: 0
LinRsvdMaskSize: 0
LinRsvdFieldPosition: 0
MaxPixelClock: 108500000
Mode: 103 (800x600)
ModeAttributes: 0x39f
WinAAttributes: 0x7
WinBAttributes: 0x0
WinGranularity: 64
WinSize: 64
WinASegment: 0xa000
WinBSegment: 0x0
WinFuncPtr: 0xc000956a
BytesPerScanline: 800
XResolution: 800
YResolution: 600
XCharSize: 8
YCharSize: 16
NumberOfPlanes: 1
BitsPerPixel: 8
NumberOfBanks: 1
MemoryModel: 4
BankSize: 0
NumberOfImages: 7
RedMaskSize: 0
RedFieldPosition: 0
GreenMaskSize: 0
GreenFieldPosition: 0
BlueMaskSize: 0
BlueFieldPosition: 0
RsvdMaskSize: 0
RsvdFieldPosition: 0
DirectColorModeInfo: 0
PhysBasePtr: 0xe0000000
LinBytesPerScanLine: 800
BnkNumberOfImagePages: 7
LinNumberOfImagePages: 7
LinRedMaskSize: 0
LinRedFieldPosition: 0
LinGreenMaskSize: 0
LinGreenFieldPosition: 0
LinBlueMaskSize: 0
LinBlueFieldPosition: 0
LinRsvdMaskSize: 0
LinRsvdFieldPosition: 0
MaxPixelClock: 229500000
Mode: 104 (1024x768)
ModeAttributes: 0x31f
WinAAttributes: 0x7
WinBAttributes: 0x0
WinGranularity: 64
WinSize: 64
WinASegment: 0xa000
WinBSegment: 0x0
WinFuncPtr: 0xc000956a
BytesPerScanline: 128
XResolution: 1024
YResolution: 768
XCharSize: 8
YCharSize: 16
NumberOfPlanes: 4
BitsPerPixel: 4
NumberOfBanks: 1
MemoryModel: 3
BankSize: 0
NumberOfImages: 7
RedMaskSize: 0
RedFieldPosition: 0
GreenMaskSize: 0
GreenFieldPosition: 0
BlueMaskSize: 0
BlueFieldPosition: 0
RsvdMaskSize: 0
RsvdFieldPosition: 0
DirectColorModeInfo: 0
PhysBasePtr: 0x0
LinBytesPerScanLine: 128
BnkNumberOfImagePages: 7
LinNumberOfImagePages: 7
LinRedMaskSize: 0
LinRedFieldPosition: 0
LinGreenMaskSize: 0
LinGreenFieldPosition: 0
LinBlueMaskSize: 0
LinBlueFieldPosition: 0
LinRsvdMaskSize: 0
LinRsvdFieldPosition: 0
MaxPixelClock: 108500000
Mode: 105 (1024x768)
ModeAttributes: 0x39f
WinAAttributes: 0x7
WinBAttributes: 0x0
WinGranularity: 64
WinSize: 64
WinASegment: 0xa000
WinBSegment: 0x0
WinFuncPtr: 0xc000956a
BytesPerScanline: 1024
XResolution: 1024
YResolution: 768
XCharSize: 8
YCharSize: 16
NumberOfPlanes: 1
BitsPerPixel: 8
NumberOfBanks: 1
MemoryModel: 4
BankSize: 0
NumberOfImages: 4
RedMaskSize: 0
RedFieldPosition: 0
GreenMaskSize: 0
GreenFieldPosition: 0
BlueMaskSize: 0
BlueFieldPosition: 0
RsvdMaskSize: 0
RsvdFieldPosition: 0
DirectColorModeInfo: 0
PhysBasePtr: 0xe0000000
LinBytesPerScanLine: 1024
BnkNumberOfImagePages: 4
LinNumberOfImagePages: 4
LinRedMaskSize: 0
LinRedFieldPosition: 0
LinGreenMaskSize: 0
LinGreenFieldPosition: 0
LinBlueMaskSize: 0
LinBlueFieldPosition: 0
LinRsvdMaskSize: 0
LinRsvdFieldPosition: 0
MaxPixelClock: 229500000
Mode: 106 (1280x1024)
ModeAttributes: 0x31f
WinAAttributes: 0x7
WinBAttributes: 0x0
WinGranularity: 64
WinSize: 64
WinASegment: 0xa000
WinBSegment: 0x0
WinFuncPtr: 0xc000956a
BytesPerScanline: 160
XResolution: 1280
YResolution: 1024
XCharSize: 8
YCharSize: 16
NumberOfPlanes: 4
BitsPerPixel: 4
NumberOfBanks: 1
MemoryModel: 3
BankSize: 0
NumberOfImages: 4
RedMaskSize: 0
RedFieldPosition: 0
GreenMaskSize: 0
GreenFieldPosition: 0
BlueMaskSize: 0
BlueFieldPosition: 0
RsvdMaskSize: 0
RsvdFieldPosition: 0
DirectColorModeInfo: 0
PhysBasePtr: 0x0
LinBytesPerScanLine: 160
BnkNumberOfImagePages: 4
LinNumberOfImagePages: 4
LinRedMaskSize: 0
LinRedFieldPosition: 0
LinGreenMaskSize: 0
LinGreenFieldPosition: 0
LinBlueMaskSize: 0
LinBlueFieldPosition: 0
LinRsvdMaskSize: 0
LinRsvdFieldPosition: 0
MaxPixelClock: 108500000
Mode: 107 (1280x1024)
ModeAttributes: 0x39f
WinAAttributes: 0x7
WinBAttributes: 0x0
WinGranularity: 64
WinSize: 64
WinASegment: 0xa000
WinBSegment: 0x0
WinFuncPtr: 0xc000956a
BytesPerScanline: 1280
XResolution: 1280
YResolution: 1024
XCharSize: 8
YCharSize: 16
NumberOfPlanes: 1
BitsPerPixel: 8
NumberOfBanks: 1
MemoryModel: 4
BankSize: 0
NumberOfImages: 2
RedMaskSize: 0
RedFieldPosition: 0
GreenMaskSize: 0
GreenFieldPosition: 0
BlueMaskSize: 0
BlueFieldPosition: 0
RsvdMaskSize: 0
RsvdFieldPosition: 0
DirectColorModeInfo: 0
PhysBasePtr: 0xe0000000
LinBytesPerScanLine: 1280
BnkNumberOfImagePages: 2
LinNumberOfImagePages: 2
LinRedMaskSize: 0
LinRedFieldPosition: 0
LinGreenMaskSize: 0
LinGreenFieldPosition: 0
LinBlueMaskSize: 0
LinBlueFieldPosition: 0
LinRsvdMaskSize: 0
LinRsvdFieldPosition: 0
MaxPixelClock: 229500000
Mode: 108 (80x60)
ModeAttributes: 0x38f
WinAAttributes: 0x7
WinBAttributes: 0x0
WinGranularity: 32
WinSize: 32
WinASegment: 0xb800
WinBSegment: 0x0
WinFuncPtr: 0xc000956a
BytesPerScanline: 160
XResolution: 80
YResolution: 60
XCharSize: 8
YCharSize: 8
NumberOfPlanes: 1
BitsPerPixel: 4
NumberOfBanks: 1
MemoryModel: 0
BankSize: 0
NumberOfImages: 0
RedMaskSize: 0
RedFieldPosition: 0
GreenMaskSize: 0
GreenFieldPosition: 0
BlueMaskSize: 0
BlueFieldPosition: 0
RsvdMaskSize: 0
RsvdFieldPosition: 0
DirectColorModeInfo: 0
PhysBasePtr: 0xe0000000
LinBytesPerScanLine: 160
BnkNumberOfImagePages: 0
LinNumberOfImagePages: 0
LinRedMaskSize: 0
LinRedFieldPosition: 0
LinGreenMaskSize: 0
LinGreenFieldPosition: 0
LinBlueMaskSize: 0
LinBlueFieldPosition: 0
LinRsvdMaskSize: 0
LinRsvdFieldPosition: 0
MaxPixelClock: 108500000
Mode: 109 (132x25)
ModeAttributes: 0x38f
WinAAttributes: 0x7
WinBAttributes: 0x0
WinGranularity: 32
WinSize: 32
WinASegment: 0xb800
WinBSegment: 0x0
WinFuncPtr: 0xc000956a
BytesPerScanline: 264
XResolution: 132
YResolution: 25
XCharSize: 8
YCharSize: 16
NumberOfPlanes: 1
BitsPerPixel: 4
NumberOfBanks: 1
MemoryModel: 0
BankSize: 0
NumberOfImages: 0
RedMaskSize: 0
RedFieldPosition: 0
GreenMaskSize: 0
GreenFieldPosition: 0
BlueMaskSize: 0
BlueFieldPosition: 0
RsvdMaskSize: 0
RsvdFieldPosition: 0
DirectColorModeInfo: 0
PhysBasePtr: 0xe0000000
LinBytesPerScanLine: 264
BnkNumberOfImagePages: 0
LinNumberOfImagePages: 0
LinRedMaskSize: 0
LinRedFieldPosition: 0
LinGreenMaskSize: 0
LinGreenFieldPosition: 0
LinBlueMaskSize: 0
LinBlueFieldPosition: 0
LinRsvdMaskSize: 0
LinRsvdFieldPosition: 0
MaxPixelClock: 108500000
Mode: 10a (132x43)
ModeAttributes: 0x38f
WinAAttributes: 0x7
WinBAttributes: 0x0
WinGranularity: 32
WinSize: 32
WinASegment: 0xb800
WinBSegment: 0x0
WinFuncPtr: 0xc000956a
BytesPerScanline: 264
XResolution: 132
YResolution: 43
XCharSize: 8
YCharSize: 9
NumberOfPlanes: 1
BitsPerPixel: 4
NumberOfBanks: 1
MemoryModel: 0
BankSize: 0
NumberOfImages: 0
RedMaskSize: 0
RedFieldPosition: 0
GreenMaskSize: 0
GreenFieldPosition: 0
BlueMaskSize: 0
BlueFieldPosition: 0
RsvdMaskSize: 0
RsvdFieldPosition: 0
DirectColorModeInfo: 0
PhysBasePtr: 0xe0000000
LinBytesPerScanLine: 264
BnkNumberOfImagePages: 0
LinNumberOfImagePages: 0
LinRedMaskSize: 0
LinRedFieldPosition: 0
LinGreenMaskSize: 0
LinGreenFieldPosition: 0
LinBlueMaskSize: 0
LinBlueFieldPosition: 0
LinRsvdMaskSize: 0
LinRsvdFieldPosition: 0
MaxPixelClock: 108500000
Mode: 10b (132x50)
ModeAttributes: 0x38f
WinAAttributes: 0x7
WinBAttributes: 0x0
WinGranularity: 32
WinSize: 32
WinASegment: 0xb800
WinBSegment: 0x0
WinFuncPtr: 0xc000956a
BytesPerScanline: 264
XResolution: 132
YResolution: 50
XCharSize: 8
YCharSize: 8
NumberOfPlanes: 1
BitsPerPixel: 4
NumberOfBanks: 1
MemoryModel: 0
BankSize: 0
NumberOfImages: 0
RedMaskSize: 0
RedFieldPosition: 0
GreenMaskSize: 0
GreenFieldPosition: 0
BlueMaskSize: 0
BlueFieldPosition: 0
RsvdMaskSize: 0
RsvdFieldPosition: 0
DirectColorModeInfo: 0
PhysBasePtr: 0xe0000000
LinBytesPerScanLine: 264
BnkNumberOfImagePages: 0
LinNumberOfImagePages: 0
LinRedMaskSize: 0
LinRedFieldPosition: 0
LinGreenMaskSize: 0
LinGreenFieldPosition: 0
LinBlueMaskSize: 0
LinBlueFieldPosition: 0
LinRsvdMaskSize: 0
LinRsvdFieldPosition: 0
MaxPixelClock: 108500000
Mode: 10c (132x60)
ModeAttributes: 0x38f
WinAAttributes: 0x7
WinBAttributes: 0x0
WinGranularity: 32
WinSize: 32
WinASegment: 0xb800
WinBSegment: 0x0
WinFuncPtr: 0xc000956a
BytesPerScanline: 264
XResolution: 132
YResolution: 60
XCharSize: 8
YCharSize: 8
NumberOfPlanes: 1
BitsPerPixel: 4
NumberOfBanks: 1
MemoryModel: 0
BankSize: 0
NumberOfImages: 0
RedMaskSize: 0
RedFieldPosition: 0
GreenMaskSize: 0
GreenFieldPosition: 0
BlueMaskSize: 0
BlueFieldPosition: 0
RsvdMaskSize: 0
RsvdFieldPosition: 0
DirectColorModeInfo: 0
PhysBasePtr: 0xe0000000
LinBytesPerScanLine: 264
BnkNumberOfImagePages: 0
LinNumberOfImagePages: 0
LinRedMaskSize: 0
LinRedFieldPosition: 0
LinGreenMaskSize: 0
LinGreenFieldPosition: 0
LinBlueMaskSize: 0
LinBlueFieldPosition: 0
LinRsvdMaskSize: 0
LinRsvdFieldPosition: 0
MaxPixelClock: 108500000
Mode: 10e (320x200)
ModeAttributes: 0x39f
WinAAttributes: 0x7
WinBAttributes: 0x0
WinGranularity: 64
WinSize: 64
WinASegment: 0xa000
WinBSegment: 0x0
WinFuncPtr: 0xc000956a
BytesPerScanline: 640
XResolution: 320
YResolution: 200
XCharSize: 8
YCharSize: 16
NumberOfPlanes: 1
BitsPerPixel: 16
NumberOfBanks: 1
MemoryModel: 6
BankSize: 0
NumberOfImages: 31
RedMaskSize: 5
RedFieldPosition: 11
GreenMaskSize: 6
GreenFieldPosition: 5
BlueMaskSize: 5
BlueFieldPosition: 0
RsvdMaskSize: 0
RsvdFieldPosition: 0
DirectColorModeInfo: 0
PhysBasePtr: 0xe0000000
LinBytesPerScanLine: 640
BnkNumberOfImagePages: 31
LinNumberOfImagePages: 31
LinRedMaskSize: 5
LinRedFieldPosition: 11
LinGreenMaskSize: 6
LinGreenFieldPosition: 5
LinBlueMaskSize: 5
LinBlueFieldPosition: 0
LinRsvdMaskSize: 0
LinRsvdFieldPosition: 0
MaxPixelClock: 229500000
*Mode: 10f (320x200)
ModeAttributes: 0x39f
WinAAttributes: 0x7
WinBAttributes: 0x0
WinGranularity: 64
WinSize: 64
WinASegment: 0xa000
WinBSegment: 0x0
WinFuncPtr: 0xc000956a
BytesPerScanline: 1280
XResolution: 320
YResolution: 200
XCharSize: 8
YCharSize: 16
NumberOfPlanes: 1
BitsPerPixel: 32
NumberOfBanks: 1
MemoryModel: 6
BankSize: 0
NumberOfImages: 15
RedMaskSize: 8
RedFieldPosition: 16
GreenMaskSize: 8
GreenFieldPosition: 8
BlueMaskSize: 8
BlueFieldPosition: 0
RsvdMaskSize: 8
RsvdFieldPosition: 24
DirectColorModeInfo: 0
PhysBasePtr: 0xe0000000
LinBytesPerScanLine: 1280
BnkNumberOfImagePages: 15
LinNumberOfImagePages: 15
LinRedMaskSize: 8
LinRedFieldPosition: 16
LinGreenMaskSize: 8
LinGreenFieldPosition: 8
LinBlueMaskSize: 8
LinBlueFieldPosition: 0
LinRsvdMaskSize: 8
LinRsvdFieldPosition: 24
MaxPixelClock: 229500000
Mode: 111 (640x480)
ModeAttributes: 0x39f
WinAAttributes: 0x7
WinBAttributes: 0x0
WinGranularity: 64
WinSize: 64
WinASegment: 0xa000
WinBSegment: 0x0
WinFuncPtr: 0xc000956a
BytesPerScanline: 1280
XResolution: 640
YResolution: 480
XCharSize: 8
YCharSize: 16
NumberOfPlanes: 1
BitsPerPixel: 16
NumberOfBanks: 1
MemoryModel: 6
BankSize: 0
NumberOfImages: 5
RedMaskSize: 5
RedFieldPosition: 11
GreenMaskSize: 6
GreenFieldPosition: 5
BlueMaskSize: 5
BlueFieldPosition: 0
RsvdMaskSize: 0
RsvdFieldPosition: 0
DirectColorModeInfo: 0
PhysBasePtr: 0xe0000000
LinBytesPerScanLine: 1280
BnkNumberOfImagePages: 5
LinNumberOfImagePages: 5
LinRedMaskSize: 5
LinRedFieldPosition: 11
LinGreenMaskSize: 6
LinGreenFieldPosition: 5
LinBlueMaskSize: 5
LinBlueFieldPosition: 0
LinRsvdMaskSize: 0
LinRsvdFieldPosition: 0
MaxPixelClock: 229500000
*Mode: 112 (640x480)
ModeAttributes: 0x39f
WinAAttributes: 0x7
WinBAttributes: 0x0
WinGranularity: 64
WinSize: 64
WinASegment: 0xa000
WinBSegment: 0x0
WinFuncPtr: 0xc000956a
BytesPerScanline: 2560
XResolution: 640
YResolution: 480
XCharSize: 8
YCharSize: 16
NumberOfPlanes: 1
BitsPerPixel: 32
NumberOfBanks: 1
MemoryModel: 6
BankSize: 0
NumberOfImages: 2
RedMaskSize: 8
RedFieldPosition: 16
GreenMaskSize: 8
GreenFieldPosition: 8
BlueMaskSize: 8
BlueFieldPosition: 0
RsvdMaskSize: 8
RsvdFieldPosition: 24
DirectColorModeInfo: 0
PhysBasePtr: 0xe0000000
LinBytesPerScanLine: 2560
BnkNumberOfImagePages: 2
LinNumberOfImagePages: 2
LinRedMaskSize: 8
LinRedFieldPosition: 16
LinGreenMaskSize: 8
LinGreenFieldPosition: 8
LinBlueMaskSize: 8
LinBlueFieldPosition: 0
LinRsvdMaskSize: 8
LinRsvdFieldPosition: 24
MaxPixelClock: 229500000
Mode: 114 (800x600)
ModeAttributes: 0x39f
WinAAttributes: 0x7
WinBAttributes: 0x0
WinGranularity: 64
WinSize: 64
WinASegment: 0xa000
WinBSegment: 0x0
WinFuncPtr: 0xc000956a
BytesPerScanline: 1600
XResolution: 800
YResolution: 600
XCharSize: 8
YCharSize: 16
NumberOfPlanes: 1
BitsPerPixel: 16
NumberOfBanks: 1
MemoryModel: 6
BankSize: 0
NumberOfImages: 3
RedMaskSize: 5
RedFieldPosition: 11
GreenMaskSize: 6
GreenFieldPosition: 5
BlueMaskSize: 5
BlueFieldPosition: 0
RsvdMaskSize: 0
RsvdFieldPosition: 0
DirectColorModeInfo: 0
PhysBasePtr: 0xe0000000
LinBytesPerScanLine: 1600
BnkNumberOfImagePages: 3
LinNumberOfImagePages: 3
LinRedMaskSize: 5
LinRedFieldPosition: 11
LinGreenMaskSize: 6
LinGreenFieldPosition: 5
LinBlueMaskSize: 5
LinBlueFieldPosition: 0
LinRsvdMaskSize: 0
LinRsvdFieldPosition: 0
MaxPixelClock: 229500000
*Mode: 115 (800x600)
ModeAttributes: 0x39f
WinAAttributes: 0x7
WinBAttributes: 0x0
WinGranularity: 64
WinSize: 64
WinASegment: 0xa000
WinBSegment: 0x0
WinFuncPtr: 0xc000956a
BytesPerScanline: 3200
XResolution: 800
YResolution: 600
XCharSize: 8
YCharSize: 16
NumberOfPlanes: 1
BitsPerPixel: 32
NumberOfBanks: 1
MemoryModel: 6
BankSize: 0
NumberOfImages: 0
RedMaskSize: 8
RedFieldPosition: 16
GreenMaskSize: 8
GreenFieldPosition: 8
BlueMaskSize: 8
BlueFieldPosition: 0
RsvdMaskSize: 8
RsvdFieldPosition: 24
DirectColorModeInfo: 0
PhysBasePtr: 0xe0000000
LinBytesPerScanLine: 3200
BnkNumberOfImagePages: 0
LinNumberOfImagePages: 0
LinRedMaskSize: 8
LinRedFieldPosition: 16
LinGreenMaskSize: 8
LinGreenFieldPosition: 8
LinBlueMaskSize: 8
LinBlueFieldPosition: 0
LinRsvdMaskSize: 8
LinRsvdFieldPosition: 24
MaxPixelClock: 229500000
Mode: 117 (1024x768)
ModeAttributes: 0x39f
WinAAttributes: 0x7
WinBAttributes: 0x0
WinGranularity: 64
WinSize: 64
WinASegment: 0xa000
WinBSegment: 0x0
WinFuncPtr: 0xc000956a
BytesPerScanline: 2048
XResolution: 1024
YResolution: 768
XCharSize: 8
YCharSize: 16
NumberOfPlanes: 1
BitsPerPixel: 16
NumberOfBanks: 1
MemoryModel: 6
BankSize: 0
NumberOfImages: 0
RedMaskSize: 5
RedFieldPosition: 11
GreenMaskSize: 6
GreenFieldPosition: 5
BlueMaskSize: 5
BlueFieldPosition: 0
RsvdMaskSize: 0
RsvdFieldPosition: 0
DirectColorModeInfo: 0
PhysBasePtr: 0xe0000000
LinBytesPerScanLine: 2048
BnkNumberOfImagePages: 0
LinNumberOfImagePages: 0
LinRedMaskSize: 5
LinRedFieldPosition: 11
LinGreenMaskSize: 6
LinGreenFieldPosition: 5
LinBlueMaskSize: 5
LinBlueFieldPosition: 0
LinRsvdMaskSize: 0
LinRsvdFieldPosition: 0
MaxPixelClock: 229500000
*Mode: 118 (1024x768)
ModeAttributes: 0x39f
WinAAttributes: 0x7
WinBAttributes: 0x0
WinGranularity: 64
WinSize: 64
WinASegment: 0xa000
WinBSegment: 0x0
WinFuncPtr: 0xc000956a
BytesPerScanline: 4096
XResolution: 1024
YResolution: 768
XCharSize: 8
YCharSize: 16
NumberOfPlanes: 1
BitsPerPixel: 32
NumberOfBanks: 1
MemoryModel: 6
BankSize: 0
NumberOfImages: 1
RedMaskSize: 8
RedFieldPosition: 16
GreenMaskSize: 8
GreenFieldPosition: 8
BlueMaskSize: 8
BlueFieldPosition: 0
RsvdMaskSize: 8
RsvdFieldPosition: 24
DirectColorModeInfo: 0
PhysBasePtr: 0xe0000000
LinBytesPerScanLine: 4096
BnkNumberOfImagePages: 1
LinNumberOfImagePages: 1
LinRedMaskSize: 8
LinRedFieldPosition: 16
LinGreenMaskSize: 8
LinGreenFieldPosition: 8
LinBlueMaskSize: 8
LinBlueFieldPosition: 0
LinRsvdMaskSize: 8
LinRsvdFieldPosition: 24
MaxPixelClock: 229500000
Mode: 11a (1280x1024)
ModeAttributes: 0x39f
WinAAttributes: 0x7
WinBAttributes: 0x0
WinGranularity: 64
WinSize: 64
WinASegment: 0xa000
WinBSegment: 0x0
WinFuncPtr: 0xc000956a
BytesPerScanline: 2560
XResolution: 1280
YResolution: 1024
XCharSize: 8
YCharSize: 16
NumberOfPlanes: 1
BitsPerPixel: 16
NumberOfBanks: 1
MemoryModel: 6
BankSize: 0
NumberOfImages: 1
RedMaskSize: 5
RedFieldPosition: 11
GreenMaskSize: 6
GreenFieldPosition: 5
BlueMaskSize: 5
BlueFieldPosition: 0
RsvdMaskSize: 0
RsvdFieldPosition: 0
DirectColorModeInfo: 0
PhysBasePtr: 0xe0000000
LinBytesPerScanLine: 2560
BnkNumberOfImagePages: 1
LinNumberOfImagePages: 1
LinRedMaskSize: 5
LinRedFieldPosition: 11
LinGreenMaskSize: 6
LinGreenFieldPosition: 5
LinBlueMaskSize: 5
LinBlueFieldPosition: 0
LinRsvdMaskSize: 0
LinRsvdFieldPosition: 0
MaxPixelClock: 229500000
Mode: 130 (320x200)
ModeAttributes: 0x39f
WinAAttributes: 0x7
WinBAttributes: 0x0
WinGranularity: 64
WinSize: 64
WinASegment: 0xa000
WinBSegment: 0x0
WinFuncPtr: 0xc000956a
BytesPerScanline: 320
XResolution: 320
YResolution: 200
XCharSize: 8
YCharSize: 16
NumberOfPlanes: 1
BitsPerPixel: 8
NumberOfBanks: 1
MemoryModel: 4
BankSize: 0
NumberOfImages: 63
RedMaskSize: 0
RedFieldPosition: 0
GreenMaskSize: 0
GreenFieldPosition: 0
BlueMaskSize: 0
BlueFieldPosition: 0
RsvdMaskSize: 0
RsvdFieldPosition: 0
DirectColorModeInfo: 0
PhysBasePtr: 0xe0000000
LinBytesPerScanLine: 320
BnkNumberOfImagePages: 63
LinNumberOfImagePages: 63
LinRedMaskSize: 0
LinRedFieldPosition: 0
LinGreenMaskSize: 0
LinGreenFieldPosition: 0
LinBlueMaskSize: 0
LinBlueFieldPosition: 0
LinRsvdMaskSize: 0
LinRsvdFieldPosition: 0
MaxPixelClock: 229500000
Mode: 131 (320x400)
ModeAttributes: 0x39f
WinAAttributes: 0x7
WinBAttributes: 0x0
WinGranularity: 64
WinSize: 64
WinASegment: 0xa000
WinBSegment: 0x0
WinFuncPtr: 0xc000956a
BytesPerScanline: 320
XResolution: 320
YResolution: 400
XCharSize: 8
YCharSize: 16
NumberOfPlanes: 1
BitsPerPixel: 8
NumberOfBanks: 1
MemoryModel: 4
BankSize: 0
NumberOfImages: 31
RedMaskSize: 0
RedFieldPosition: 0
GreenMaskSize: 0
GreenFieldPosition: 0
BlueMaskSize: 0
BlueFieldPosition: 0
RsvdMaskSize: 0
RsvdFieldPosition: 0
DirectColorModeInfo: 0
PhysBasePtr: 0xe0000000
LinBytesPerScanLine: 320
BnkNumberOfImagePages: 31
LinNumberOfImagePages: 31
LinRedMaskSize: 0
LinRedFieldPosition: 0
LinGreenMaskSize: 0
LinGreenFieldPosition: 0
LinBlueMaskSize: 0
LinBlueFieldPosition: 0
LinRsvdMaskSize: 0
LinRsvdFieldPosition: 0
MaxPixelClock: 229500000
Mode: 132 (320x400)
ModeAttributes: 0x39f
WinAAttributes: 0x7
WinBAttributes: 0x0
WinGranularity: 64
WinSize: 64
WinASegment: 0xa000
WinBSegment: 0x0
WinFuncPtr: 0xc000956a
BytesPerScanline: 640
XResolution: 320
YResolution: 400
XCharSize: 8
YCharSize: 16
NumberOfPlanes: 1
BitsPerPixel: 16
NumberOfBanks: 1
MemoryModel: 6
BankSize: 0
NumberOfImages: 15
RedMaskSize: 5
RedFieldPosition: 11
GreenMaskSize: 6
GreenFieldPosition: 5
BlueMaskSize: 5
BlueFieldPosition: 0
RsvdMaskSize: 0
RsvdFieldPosition: 0
DirectColorModeInfo: 0
PhysBasePtr: 0xe0000000
LinBytesPerScanLine: 640
BnkNumberOfImagePages: 15
LinNumberOfImagePages: 15
LinRedMaskSize: 5
LinRedFieldPosition: 11
LinGreenMaskSize: 6
LinGreenFieldPosition: 5
LinBlueMaskSize: 5
LinBlueFieldPosition: 0
LinRsvdMaskSize: 0
LinRsvdFieldPosition: 0
MaxPixelClock: 229500000
*Mode: 133 (320x400)
ModeAttributes: 0x39f
WinAAttributes: 0x7
WinBAttributes: 0x0
WinGranularity: 64
WinSize: 64
WinASegment: 0xa000
WinBSegment: 0x0
WinFuncPtr: 0xc000956a
BytesPerScanline: 1280
XResolution: 320
YResolution: 400
XCharSize: 8
YCharSize: 16
NumberOfPlanes: 1
BitsPerPixel: 32
NumberOfBanks: 1
MemoryModel: 6
BankSize: 0
NumberOfImages: 7
RedMaskSize: 8
RedFieldPosition: 16
GreenMaskSize: 8
GreenFieldPosition: 8
BlueMaskSize: 8
BlueFieldPosition: 0
RsvdMaskSize: 8
RsvdFieldPosition: 24
DirectColorModeInfo: 0
PhysBasePtr: 0xe0000000
LinBytesPerScanLine: 1280
BnkNumberOfImagePages: 7
LinNumberOfImagePages: 7
LinRedMaskSize: 8
LinRedFieldPosition: 16
LinGreenMaskSize: 8
LinGreenFieldPosition: 8
LinBlueMaskSize: 8
LinBlueFieldPosition: 0
LinRsvdMaskSize: 8
LinRsvdFieldPosition: 24
MaxPixelClock: 229500000
Mode: 134 (320x240)
ModeAttributes: 0x39f
WinAAttributes: 0x7
WinBAttributes: 0x0
WinGranularity: 64
WinSize: 64
WinASegment: 0xa000
WinBSegment: 0x0
WinFuncPtr: 0xc000956a
BytesPerScanline: 320
XResolution: 320
YResolution: 240
XCharSize: 8
YCharSize: 16
NumberOfPlanes: 1
BitsPerPixel: 8
NumberOfBanks: 1
MemoryModel: 4
BankSize: 0
NumberOfImages: 31
RedMaskSize: 0
RedFieldPosition: 0
GreenMaskSize: 0
GreenFieldPosition: 0
BlueMaskSize: 0
BlueFieldPosition: 0
RsvdMaskSize: 0
RsvdFieldPosition: 0
DirectColorModeInfo: 0
PhysBasePtr: 0xe0000000
LinBytesPerScanLine: 320
BnkNumberOfImagePages: 31
LinNumberOfImagePages: 31
LinRedMaskSize: 0
LinRedFieldPosition: 0
LinGreenMaskSize: 0
LinGreenFieldPosition: 0
LinBlueMaskSize: 0
LinBlueFieldPosition: 0
LinRsvdMaskSize: 0
LinRsvdFieldPosition: 0
MaxPixelClock: 229500000
Mode: 135 (320x240)
ModeAttributes: 0x39f
WinAAttributes: 0x7
WinBAttributes: 0x0
WinGranularity: 64
WinSize: 64
WinASegment: 0xa000
WinBSegment: 0x0
WinFuncPtr: 0xc000956a
BytesPerScanline: 640
XResolution: 320
YResolution: 240
XCharSize: 8
YCharSize: 16
NumberOfPlanes: 1
BitsPerPixel: 16
NumberOfBanks: 1
MemoryModel: 6
BankSize: 0
NumberOfImages: 20
RedMaskSize: 5
RedFieldPosition: 11
GreenMaskSize: 6
GreenFieldPosition: 5
BlueMaskSize: 5
BlueFieldPosition: 0
RsvdMaskSize: 0
RsvdFieldPosition: 0
DirectColorModeInfo: 0
PhysBasePtr: 0xe0000000
LinBytesPerScanLine: 640
BnkNumberOfImagePages: 20
LinNumberOfImagePages: 20
LinRedMaskSize: 5
LinRedFieldPosition: 11
LinGreenMaskSize: 6
LinGreenFieldPosition: 5
LinBlueMaskSize: 5
LinBlueFieldPosition: 0
LinRsvdMaskSize: 0
LinRsvdFieldPosition: 0
MaxPixelClock: 229500000
*Mode: 136 (320x240)
ModeAttributes: 0x39f
WinAAttributes: 0x7
WinBAttributes: 0x0
WinGranularity: 64
WinSize: 64
WinASegment: 0xa000
WinBSegment: 0x0
WinFuncPtr: 0xc000956a
BytesPerScanline: 1280
XResolution: 320
YResolution: 240
XCharSize: 8
YCharSize: 16
NumberOfPlanes: 1
BitsPerPixel: 32
NumberOfBanks: 1
MemoryModel: 6
BankSize: 0
NumberOfImages: 11
RedMaskSize: 8
RedFieldPosition: 16
GreenMaskSize: 8
GreenFieldPosition: 8
BlueMaskSize: 8
BlueFieldPosition: 0
RsvdMaskSize: 8
RsvdFieldPosition: 24
DirectColorModeInfo: 0
PhysBasePtr: 0xe0000000
LinBytesPerScanLine: 1280
BnkNumberOfImagePages: 11
LinNumberOfImagePages: 11
LinRedMaskSize: 8
LinRedFieldPosition: 16
LinGreenMaskSize: 8
LinGreenFieldPosition: 8
LinBlueMaskSize: 8
LinBlueFieldPosition: 0
LinRsvdMaskSize: 8
LinRsvdFieldPosition: 24
MaxPixelClock: 229500000
Mode: 13d (640x400)
ModeAttributes: 0x39f
WinAAttributes: 0x7
WinBAttributes: 0x0
WinGranularity: 64
WinSize: 64
WinASegment: 0xa000
WinBSegment: 0x0
WinFuncPtr: 0xc000956a
BytesPerScanline: 1280
XResolution: 640
YResolution: 400
XCharSize: 8
YCharSize: 16
NumberOfPlanes: 1
BitsPerPixel: 16
NumberOfBanks: 1
MemoryModel: 6
BankSize: 0
NumberOfImages: 7
RedMaskSize: 5
RedFieldPosition: 11
GreenMaskSize: 6
GreenFieldPosition: 5
BlueMaskSize: 5
BlueFieldPosition: 0
RsvdMaskSize: 0
RsvdFieldPosition: 0
DirectColorModeInfo: 0
PhysBasePtr: 0xe0000000
LinBytesPerScanLine: 1280
BnkNumberOfImagePages: 7
LinNumberOfImagePages: 7
LinRedMaskSize: 5
LinRedFieldPosition: 11
LinGreenMaskSize: 6
LinGreenFieldPosition: 5
LinBlueMaskSize: 5
LinBlueFieldPosition: 0
LinRsvdMaskSize: 0
LinRsvdFieldPosition: 0
MaxPixelClock: 229500000
*Mode: 13e (640x400)
ModeAttributes: 0x39f
WinAAttributes: 0x7
WinBAttributes: 0x0
WinGranularity: 64
WinSize: 64
WinASegment: 0xa000
WinBSegment: 0x0
WinFuncPtr: 0xc000956a
BytesPerScanline: 2560
XResolution: 640
YResolution: 400
XCharSize: 8
YCharSize: 16
NumberOfPlanes: 1
BitsPerPixel: 32
NumberOfBanks: 1
MemoryModel: 6
BankSize: 0
NumberOfImages: 3
RedMaskSize: 8
RedFieldPosition: 16
GreenMaskSize: 8
GreenFieldPosition: 8
BlueMaskSize: 8
BlueFieldPosition: 0
RsvdMaskSize: 8
RsvdFieldPosition: 24
DirectColorModeInfo: 0
PhysBasePtr: 0xe0000000
LinBytesPerScanLine: 2560
BnkNumberOfImagePages: 3
LinNumberOfImagePages: 3
LinRedMaskSize: 8
LinRedFieldPosition: 16
LinGreenMaskSize: 8
LinGreenFieldPosition: 8
LinBlueMaskSize: 8
LinBlueFieldPosition: 0
LinRsvdMaskSize: 8
LinRsvdFieldPosition: 24
MaxPixelClock: 229500000
Mode: 145 (1600x1200)
ModeAttributes: 0x39f
WinAAttributes: 0x7
WinBAttributes: 0x0
WinGranularity: 64
WinSize: 64
WinASegment: 0xa000
WinBSegment: 0x0
WinFuncPtr: 0xc000956a
BytesPerScanline: 1600
XResolution: 1600
YResolution: 1200
XCharSize: 8
YCharSize: 16
NumberOfPlanes: 1
BitsPerPixel: 8
NumberOfBanks: 1
MemoryModel: 4
BankSize: 0
NumberOfImages: 0
RedMaskSize: 0
RedFieldPosition: 0
GreenMaskSize: 0
GreenFieldPosition: 0
BlueMaskSize: 0
BlueFieldPosition: 0
RsvdMaskSize: 0
RsvdFieldPosition: 0
DirectColorModeInfo: 0
PhysBasePtr: 0xe0000000
LinBytesPerScanLine: 1600
BnkNumberOfImagePages: 0
LinNumberOfImagePages: 0
LinRedMaskSize: 0
LinRedFieldPosition: 0
LinGreenMaskSize: 0
LinGreenFieldPosition: 0
LinBlueMaskSize: 0
LinBlueFieldPosition: 0
LinRsvdMaskSize: 0
LinRsvdFieldPosition: 0
MaxPixelClock: 229500000
Mode: 146 (1600x1200)
ModeAttributes: 0x39f
WinAAttributes: 0x7
WinBAttributes: 0x0
WinGranularity: 64
WinSize: 64
WinASegment: 0xa000
WinBSegment: 0x0
WinFuncPtr: 0xc000956a
BytesPerScanline: 3200
XResolution: 1600
YResolution: 1200
XCharSize: 8
YCharSize: 16
NumberOfPlanes: 1
BitsPerPixel: 16
NumberOfBanks: 1
MemoryModel: 6
BankSize: 0
NumberOfImages: 1
RedMaskSize: 5
RedFieldPosition: 11
GreenMaskSize: 6
GreenFieldPosition: 5
BlueMaskSize: 5
BlueFieldPosition: 0
RsvdMaskSize: 0
RsvdFieldPosition: 0
DirectColorModeInfo: 0
PhysBasePtr: 0xe0000000
LinBytesPerScanLine: 3200
BnkNumberOfImagePages: 1
LinNumberOfImagePages: 1
LinRedMaskSize: 5
LinRedFieldPosition: 11
LinGreenMaskSize: 6
LinGreenFieldPosition: 5
LinBlueMaskSize: 5
LinBlueFieldPosition: 0
LinRsvdMaskSize: 0
LinRsvdFieldPosition: 0
MaxPixelClock: 229500000

(II) VESA(0): Total Memory: 512 64KB banks (32768kB)
(II) VESA(0): <default monitor>: Using default hsync range of 31.50-37.90 kHz
(II) VESA(0): <default monitor>: Using default vrefresh range of 50.00-70.00 Hz
(WW) VESA(0): Unable to estimate virtual size
(II) VESA(0): Not using built-in mode "1024x768" (no mode of this name)
(II) VESA(0): Not using built-in mode "800x600" (no mode of this name)
(II) VESA(0): Not using built-in mode "640x480" (no mode of this name)
(II) VESA(0): Not using built-in mode "640x400" (no mode of this name)
(II) VESA(0): Not using built-in mode "320x400" (no mode of this name)
(II) VESA(0): Not using built-in mode "320x240" (no mode of this name)
(II) VESA(0): Not using built-in mode "320x200" (no mode of this name)
(WW) VESA(0): No valid modes left. Trying less strict filter...
(II) VESA(0): <default monitor>: Using hsync range of 31.50-37.90 kHz
(II) VESA(0): <default monitor>: Using vrefresh range of 50.00-70.00 Hz
(WW) VESA(0): Unable to estimate virtual size
(II) VESA(0): Not using built-in mode "1024x768" (hsync out of range)
(II) VESA(0): Not using built-in mode "640x400" (hsync out of range)
(II) VESA(0): Not using built-in mode "320x400" (hsync out of range)
(II) VESA(0): Not using built-in mode "320x240" (illegal horizontal timings)
(II) VESA(0): Not using built-in mode "320x200" (illegal horizontal timings)
(--) VESA(0): Virtual size is 800x600 (pitch 800)
(**) VESA(0): *Built-in mode "800x600"
(**) VESA(0): *Built-in mode "640x480"
(==) VESA(0): DPI set to (96, 96)
(II) VESA(0): Attempting to use 60Hz refresh for mode "800x600" (115)
(II) VESA(0): Attempting to use 60Hz refresh for mode "640x480" (112)
(**) VESA(0): Using "Shadow Framebuffer"
(II) Loading sub module "shadow"
(II) LoadModule: "shadow"
(II) Loading /usr/lib/xorg/modules/libshadow.so
(II) Module shadow: vendor="X.Org Foundation"
compiled for 1.7.6, module version = 1.1.0
ABI class: X.Org ANSI C Emulation, version 0.4
(II) Loading sub module "fb"
(II) LoadModule: "fb"
(II) Loading /usr/lib/xorg/modules/libfb.so
(II) Module fb: vendor="X.Org Foundation"
compiled for 1.7.6, module version = 1.0.0
ABI class: X.Org ANSI C Emulation, version 0.4
(II) UnloadModule: "nv"
(II) Unloading /usr/lib/xorg/modules/drivers/nv_drv.so
(II) UnloadModule: "fbdev"
(II) Unloading /usr/lib/xorg/modules/drivers/fbdev_drv.so
(II) UnloadModule: "fbdevhw"
(II) Unloading /usr/lib/xorg/modules/linux/libfbdevhw.so
(==) Depth 24 pixmap format is 32 bpp
(II) Loading sub module "int10"
(II) LoadModule: "int10"
(II) Reloading /usr/lib/xorg/modules/libint10.so
(II) VESA(0): initializing int10
(II) VESA(0): Primary V_BIOS segment is: 0xc000
(II) VESA(0): VESA BIOS detected
(II) VESA(0): VESA VBE Version 3.0
(II) VESA(0): VESA VBE Total Mem: 32768 kB
(II) VESA(0): VESA VBE OEM: NVidia
(II) VESA(0): VESA VBE OEM Software Rev: 3.17
(II) VESA(0): VESA VBE OEM Vendor: NVidia Corporation
(II) VESA(0): VESA VBE OEM Product: NV11 (GeForce2) Board
(II) VESA(0): VESA VBE OEM Product Rev: Chip Rev B2
(II) VESA(0): virtual address = 0xb56f7000,
physical address = 0xe0000000, size = 33554432
(II) VESA(0): Setting up VESA Mode 0x115 (800x600)
(==) VESA(0): Default visual is TrueColor
(==) VESA(0): Backing store disabled
(==) VESA(0): DPMS enabled
(==) RandR enabled
(II) Initializing built-in extension Generic Event Extension
(II) Initializing built-in extension SHAPE
(II) Initializing built-in extension MIT-SHM
(II) Initializing built-in extension XInputExtension
(II) Initializing built-in extension XTEST
(II) Initializing built-in extension BIG-REQUESTS
(II) Initializing built-in extension SYNC
(II) Initializing built-in extension XKEYBOARD
(II) Initializing built-in extension XC-MISC
(II) Initializing built-in extension SECURITY
(II) Initializing built-in extension XINERAMA
(II) Initializing built-in extension XFIXES
(II) Initializing built-in extension RENDER
(II) Initializing built-in extension RANDR
(II) Initializing built-in extension COMPOSITE
(II) Initializing built-in extension DAMAGE
(II) AIGLX: Screen 0 is not DRI2 capable
(II) AIGLX: Screen 0 is not DRI capable
(II) AIGLX: Loaded and initialized /usr/lib/dri/swrast_dri.so
(II) GLX: Initialized DRISWRAST GL provider for screen 0
(II) XKB: reuse xkmfile /var/lib/xkb/server-B20D7FC79C7F597315E3E501AEF10E0D866E8E92.xkm
(II) config/udev: Adding input device Power Button (/dev/input/event2)
(**) Power Button: Applying InputClass "evdev keyboard catchall"
(II) LoadModule: "evdev"
(II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
(II) Module evdev: vendor="X.Org Foundation"
compiled for 1.7.6, module version = 2.3.2
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 7.0
(**) Power Button: always reports core events
(**) Power Button: Device: "/dev/input/event2"
(II) Power Button: Found keys
(II) Power Button: Configuring as keyboard
(II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "pc105"
(**) Option "xkb_layout" "gb"
(**) Option "xkb_options" "lv3:ralt_switch"
(II) XKB: reuse xkmfile /var/lib/xkb/server-884C6C7246E5186E4DB7A4CD26B9F16BE06DFFDC.xkm
(II) config/udev: Adding input device Power Button (/dev/input/event0)
(**) Power Button: Applying InputClass "evdev keyboard catchall"
(**) Power Button: always reports core events
(**) Power Button: Device: "/dev/input/event0"
(II) Power Button: Found keys
(II) Power Button: Configuring as keyboard
(II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "pc105"
(**) Option "xkb_layout" "gb"
(**) Option "xkb_options" "lv3:ralt_switch"
(II) config/udev: Adding input device Sleep Button (/dev/input/event1)
(**) Sleep Button: Applying InputClass "evdev keyboard catchall"
(**) Sleep Button: always reports core events
(**) Sleep Button: Device: "/dev/input/event1"
(II) Sleep Button: Found keys
(II) Sleep Button: Configuring as keyboard
(II) XINPUT: Adding extended input device "Sleep Button" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "pc105"
(**) Option "xkb_layout" "gb"
(**) Option "xkb_options" "lv3:ralt_switch"
(II) config/udev: Adding input device UVC Camera (046d:0825) (/dev/input/event6)
(**) UVC Camera (046d:0825): Applying InputClass "evdev keyboard catchall"
(**) UVC Camera (046d:0825): always reports core events
(**) UVC Camera (046d:0825): Device: "/dev/input/event6"
(II) UVC Camera (046d:0825): Found keys
(II) UVC Camera (046d:0825): Configuring as keyboard
(II) XINPUT: Adding extended input device "UVC Camera (046d:0825)" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "pc105"
(**) Option "xkb_layout" "gb"
(**) Option "xkb_options" "lv3:ralt_switch"
(II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event4)
(**) AT Translated Set 2 keyboard: Applying InputClass "evdev keyboard catchall"
(**) AT Translated Set 2 keyboard: always reports core events
(**) AT Translated Set 2 keyboard: Device: "/dev/input/event4"
(II) AT Translated Set 2 keyboard: Found keys
(II) AT Translated Set 2 keyboard: Configuring as keyboard
(II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "pc105"
(**) Option "xkb_layout" "gb"
(**) Option "xkb_options" "lv3:ralt_switch"
(II) config/udev: Adding input device ImExPS/2 Logitech Explorer Mouse (/dev/input/event5)
(**) ImExPS/2 Logitech Explorer Mouse: Applying InputClass "evdev pointer catchall"
(**) ImExPS/2 Logitech Explorer Mouse: always reports core events
(**) ImExPS/2 Logitech Explorer Mouse: Device: "/dev/input/event5"
(II) ImExPS/2 Logitech Explorer Mouse: Found 9 mouse buttons
(II) ImExPS/2 Logitech Explorer Mouse: Found scroll wheel(s)
(II) ImExPS/2 Logitech Explorer Mouse: Found relative axes
(II) ImExPS/2 Logitech Explorer Mouse: Found x and y relative axes
(II) ImExPS/2 Logitech Explorer Mouse: Configuring as mouse
(**) ImExPS/2 Logitech Explorer Mouse: YAxisMapping: buttons 4 and 5
(**) ImExPS/2 Logitech Explorer Mouse: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
(II) XINPUT: Adding extended input device "ImExPS/2 Logitech Explorer Mouse" (type: MOUSE)
(II) ImExPS/2 Logitech Explorer Mouse: initialized for relative axes.
(II) config/udev: Adding input device ImExPS/2 Logitech Explorer Mouse (/dev/input/mouse1)
(II) No input driver/identifier specified (ignoring)
(II) config/udev: Adding input device Macintosh mouse button emulation (/dev/input/event3)
(**) Macintosh mouse button emulation: Applying InputClass "evdev pointer catchall"
(**) Macintosh mouse button emulation: always reports core events
(**) Macintosh mouse button emulation: Device: "/dev/input/event3"
(II) Macintosh mouse button emulation: Found 3 mouse buttons
(II) Macintosh mouse button emulation: Found relative axes
(II) Macintosh mouse button emulation: Found x and y relative axes
(II) Macintosh mouse button emulation: Configuring as mouse
(**) Macintosh mouse button emulation: YAxisMapping: buttons 4 and 5
(**) Macintosh mouse button emulation: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
(II) XINPUT: Adding extended input device "Macintosh mouse button emulation" (type: MOUSE)
(II) Macintosh mouse button emulation: initialized for relative axes.
(II) config/udev: Adding input device Macintosh mouse button emulation (/dev/input/mouse0)
(II) No input driver/identifier specified (ignoring)

---------------------------------------------------------------------------

I wait to hear from you ..... cheers

realzippy

September 25th, 2011, 03:24 PM

Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.32-33-generic root=UUID=f5596863-aaea-4446-b6db-40e3bc0947ab ro nomodeset quiet splash

"nomodeset" is still your boot option.
We have to change that before going on with nouveau or experimental.
Problem is,if we delete "nomodeset",and your machine does not boot anymore due to this,you have a problem.
Do you know how to boot your machine with "nomodeset" as boot option ?

jdneate

September 25th, 2011, 03:28 PM

No - I would prefer not to have to reload the system ......

realzippy

September 25th, 2011, 03:42 PM

With "reload" you mean fresh install?
No,I don't want you to have to do this,that is why I asked if you know how to boot manually with "nomodeset" if we have deleted "nomodeset" from grub
and your system has problems to boot.
Suggest you reboot your machine,and try the following as a practise.

press "shift" when booting to get to grub menue.
Highlight the line
Ubuntu,with linux 2.6.32-33-generic .....
press "e"
after "..quiet splash" type a "space" and "nomodeset" so it looks like:
...quiet splash nomodeset
then hit
ctrl + x

If you understood this procedure,you know how to add "nomodeset" manually for just 1 boot
if something goes wrong when we delete "nomodeset" from grub.

jdneate

September 25th, 2011, 04:07 PM

Realzippy Yes - I meant re-install.

I can get into the GRUB loader and can see how to edit the config file. I notice that the existing line has

ro space nomodeset space space quiet space splash new line.

Does the order matter or the double space have any significance ?

What do you suggest now ?

realzippy

September 25th, 2011, 04:14 PM

Honestly I do not know if a "double space" matters;I guess.
Normally it should be:

/boot/vmlinuz-2.6.32-33-generic root=UUID=f5596863-aaea-4446-b6db-40e3bc0947ab ro nomodeset quiet splash

...where I do not see a double space.
Try again.
Then delete the nomodeset,so it looks like

/boot/vmlinuz-2.6.32-33-generic root=UUID=f5596863-aaea-4446-b6db-40e3bc0947ab ro quiet splash

Then press
ctrl+x
to boot.
If it boots,we know that we can delete "nomodeset" from grub.

jdneate

September 25th, 2011, 04:18 PM

Ok - here goes. If the system is blamk - I will put the nomodeset back in the grub line

realzippy

September 25th, 2011, 04:21 PM

It is only for 1 boot,temporarily.
No need to add it again,it will be there again.

jdneate

September 25th, 2011, 04:27 PM

Realzippy .... yes did that.

I ended up with the purple screen with "Ubuntu" in the middle ( it looked like a higher resolution than normal). The 5 dots underneath were all red.

There was no music / drum roll or cursor.

realzippy

September 25th, 2011, 04:34 PM

Ok.
Now we try this:

Backup your existing xorg.conf:

sudo mv /etc/X11/xorg.conf /etc/X11/xorg.conf.old
edit: ignore it if there is none.

Then:

gksudo gedit /etc/X11/xorg.conf

Paste into empty file:

Section "Device"
Identifier "Configured Video Device"
Driver "nouveau"
EndSection

Section "Monitor"
Identifier "Configured Monitor"
HorizSync 31-60
VertRefresh 56-76
EndSection

Section "Screen"
Identifier "Default Screen"
Monitor "Configured Monitor"
Device "Configured Video Device"
EndSection

Nothing else please.
Then close file saving changes.
Then reboot again without "nomodeset" ...

jdneate

September 25th, 2011, 04:56 PM

Realzippy

Went a lot further this time before freezing......

Got purple screen - definitely at higher resolution. Got to login screen showing the computer's name but no login options/names displayed. There was drum roll and a cursor - which did not respond to the mouse. The bottom of the screen displayed the day of week and time.

I notice that the Vertrefresh specified (56-76) was outside the range of the monitor (60-75) ?

realzippy

September 25th, 2011, 05:10 PM

56 or 60,this should not matter.
Now you know how to edit xorg.conf : ;)

gksudo gedit /etc/X11/xorg.conf

change the 56/76 to 60/75,boot without nomodeset.
Guess there is no difference...
...when you are at the frozen login,can you drop to tty ?
Simply press Alt+ctrl+F2....if tty2 opens,log in with username+password,
then type

startx
remember or write down errors (or important part of it)...

jdneate

September 25th, 2011, 05:29 PM

Realzippy

edited vertrefresh to 60-75 and did reboot without nomodeset.

Got login screen with login options this time; selected administrator and screen froze. Purple screen showing cursor which would not respond to mouse.

No response to ctrl+alt+F2. Frozen.

realzippy

September 25th, 2011, 05:40 PM

Ok,now you try
not only deleting
"nomodeset"
when booting,but also adding
"fbcon=map:1"

....simply replace nomodeset with fbcon=map:1

.................................................. ..................
Btw,as you might have guessed,I do not know the resolution for your problem.
I just try to make you do what I would if I where in front of your machine.
There are 2,3 ideas left to try.
Although if we can't make it work today,we have more information,and
I can think things over/search for that nouveau problem.
I hope you don't get tired and that it is not too frustrating for you.

jdneate

September 25th, 2011, 06:00 PM

Realzippy

I left xorg.conf unchanged.

This time did not get as far when nomdeset replaced by fbcon=map:1.

I got plain purple screen with ubuntu in centre with 5 red dots beneath; there was no cursor and the system did not respond to CTL+ALT+F1

Yes getting a bit tired but very grateful for your help. Also learned a lot about the controls for the system and pleased to see how robust it is.

realzippy

September 25th, 2011, 06:06 PM

Ok,have no idea about the nouveau problem in the moment.I will investigate.
Now....
...we try the VESA driver instead.

Simply edit xorg.conf,change in Section Device
"nouveau"
to
"vesa"

Try to boot with and without nomodeset.

jdneate

September 25th, 2011, 06:19 PM

Well - I replaced "nouveau" by "vesa" in xorg.conf and rebooted with NOMODESET still in the Grub line.

It seems to have worked.

System>Prefernces>monitors>Resolution shows 5 resolutions 320x400,640x400,640x480,800x600, and 1024x768.

I have selected 1024x768.

I will remove NOMODESET from the GRUB line next and let you know the outcome.

jdneate

September 25th, 2011, 06:32 PM

With "vesa" in xorg.conf and NOMODESET deleted from the GRUB line Ubuntu starts up with an error

EE Vesa Kernel mode setting driver in use; refusing to load
EE No devices selected

On starting the system and selecting System.Preferences>monitors resolutions shows one resolution option 1024x768 and one refresh rate 0.

The display runs in high resolution.

Could you have found the answer ???

realzippy

September 25th, 2011, 06:40 PM

Ok,
so you can keep the "nomodeset" boot option and get 1024x768,
which is correct for your Proview CY565...?
Means,the resolution problem is solved ?
Still don't know why nouveau does not work.

MAFoElffen

September 25th, 2011, 06:43 PM

1.The nouveau driver does not support modelines (afaik)
2.You seem to have disabled KMS.Did you edit "nomodeset" somewhere ?
Well(?) It should / meaning it's supposed to... Except that there is an open bug with Nouveau, Lucid and modelines on that issue at the moment:
https://bugs.launchpad.net/ubuntu/+source/xserver-xorg-video-nouveau/+bug/538275

If you changed the Section "Device" > Driver "nouveau" to Section "Device" > Driver "vesa"... The VESA driver does support modelines in Lucid...

Does

sudo hwinfo --monitor
xrandr
show any of the resolutions of your monitor?

Also run

hwinfo --framebuffer
To show the resolutions of your GPU...

*** If you don't have hwinfo installed, please install it via "sudo apt-get install hwinfo"

Also as a note, temporarily delete "queit splash" from your your bootline. Some systems have a bug with the "splash" switch.

As for the Experimental 3D Driver... It's available for Meerkat, Natty and Onieric. They got it working while we were testing Natty, so I've tested it both Natty and Onieric. I honestly haven't tested it in 10.10, but it is in it's repo's.

realzippy

September 25th, 2011, 07:14 PM

Well(?) It should / meaning it's supposed to... Except that there is an open bug with Nouveau, Lucid and modelines on that issue at the moment:
https://bugs.launchpad.net/ubuntu/+source/xserver-xorg-video-nouveau/+bug/538275
Ok,thanks.
I did not know (that's why I wrote afaik).
Nouveau,modeline in xorg.conf has never worked for me, so I thought it might be a "feature" ;-) ...
...strange thing that xrandr&modeline&nouveau works,btw.

If you changed the Section "Device" > Driver "nouveau" to Section "Device" > Driver "vesa"... The VESA driver does support modelines in Lucid...
..as I understood OP now (vesa) has 1024x768,so obsolete...

Also as a note, temporarily delete "quiet splash" from your your bootline. Some systems have a bug with the "splash" switch.

You mean jdneate should try without nomodeset,quiet splash and with
xorg.conf/nouveau ?

jdneate

September 25th, 2011, 07:17 PM

Firstly - thanks very much to both of you for all your patience and to realzippy for your persistance today. As I said, I have learned a little about the system and gained confidence that once it is up and running it is robust.

I had a look at the hwinfo information ...

.................................................. .....................
spe@jdneate:~$ hwinfo --monitor
24: None 00.0: 10000 Monitor
[Created at fb.71]
Unique ID: rdCR.EY_qmtb9YY0
Hardware Class: monitor
Model: "Generic Monitor"
Vendor: "Generic"
Device: "Monitor"
Resolution: 640x480@60Hz
Driver Info #0:
Max. Resolution: 640x480
Vert. Sync Range: 50-70 Hz
Hor. Sync Range: 31-33 kHz
Config Status: cfg=new, avail=yes, need=no, active=unknown
.................................................. ........................
spe@jdneate:~$ xrandr
Screen 0: minimum 320 x 400, current 1024 x 768, maximum 1024 x 768
default connected 1024x768+0+0 0mm x 0mm
1024x768 76.0*
800x600 73.0
640x480 73.0
640x400 0.0
320x400 0.0
spe@jdneate:~$
.................................................. ....................

hwinfo --framebuffer didn't produce a meaningful output; it overwrote itself on one display line.

I have spent 6 hrs sat at this terminal today and am a bit tired; I will leave the "quiet splash" issue for the time being.

I hope to play with the system tomorrow and if OK will close the thread tomorrow. If you want any more tests carried out then let me know overnight and I will look at them tomorrow. I am now signing off for today...

Again .....thanks

MAFoElffen

September 25th, 2011, 07:47 PM

realzippy

September 25th, 2011, 07:52 PM

Firstly - thanks very much to both of you for all your patience and to realzippy for your persistance today. As I said, I have learned a little about the system and gained confidence that once it is up and running it is robust.

You are welcome.
If you are satisfied with the vesa driver @1024x768,then
set thread as solved.
If you enjoy further testing ,try
MAFoElffen's boot option.Note that he also mentioned that
if you upgraded to 10.10 the experimental driver would be available.
....there is another boot option you could try for nouveau:
video=DVI-I-1:1024x768@60
.. check kernel log if output is "DVI-I-1" or different..

realzippy

September 25th, 2011, 07:54 PM

According to the results of your monitor from xrandr (1024x768 76.0*), try using:

Modeline "1024x768 76.00" 83.00 1024 1080 1192 1360 768 769 772 803 -hsync +vsync

as your "add modeline" in your xorg.conf.

...but he already runs this mode successfully as xrandr shows (*).
So why this modeline?
Confused,but sorry,it is late here...

Edit:
You mean this modeline and nouveau instead of vesa I guess.
What about the bug?
Sorry,
as mentioned,it is late.
Back tomorrow..

MAFoElffen

September 26th, 2011, 12:02 AM

...but he already runs this mode successfully as xrandr shows (*).
So why this modeline?
Confused,but sorry,it is late here...

Edit:
You mean this modeline and nouveau instead of vesa I guess.
What about the bug?
Sorry,
as mentioned,it is late.
Back tomorrow..
@realzippy

It is late and doesn't matter now... I had thought I had remembered him previously mentioning something about 1024x768... but that might have been when he was trying the nouveau driver. By what xrandr returned (which is monitor data, not driver nor GPU data) what was there didn't match what was in his xorg.conf... Even though what was there was a valid VESA mode and should work. That xrandr said that it his monitor default.

I could be remembering wrong. I usually help about 10 graphics threads each at a time on various distro's and at Xorg. I try to keep users and threads straight in my head...

Only other at this point is mentioning the xorg "nv" driver which works with his GPU in his version of Ubuntu... It works, but only in 2D mode without hardware acceleration. That's why I prefer, the experimental driver.

The Nouveau driver doesn't work for him at this moment. The VESA driver will work for him with modelines and is basic. The NV driver will work with modelines and the quality is a little better than VESA, but not much. The Experimental 3D will work with modelines, but he would have to do a distribution upgrade to at least 10.10.

jdneate

September 26th, 2011, 08:23 PM

Hi Since last message --- the system half froze after loading Google Earth; I had Application drop down menu selected. CTRL- ALT - F1 responded and I could enter search data into Google menu and display results! none of the ubuntu buttons responded. But that was last night.
The system has run fine since then without problem - i have now loaded my backed up data ( photos, docs etc). The system looks and responds well; it will do all that I require of it.

I can not comment on the driver issue - I do not understand the syntax of the .conf system and the drivers.

I am quite happy with the presnt load; but I did notice that the pictures were very slow on Google Earth and can be distorted . ( I don't normally use this so it isn't a problem). From what I can gather I am using vesa driver software with old NVIDIA hardware. The system>harware drivers recommends v96 NVIDIA driver - would Google Earth performance improve if I used this ?
I will wait for another day for any reply and then close this thread as solved.... Many thanks

MAFoElffen

September 26th, 2011, 08:45 PM

Hi Since last message ---

I am quite happy with the presnt load; but I did notice that the pictures were very slow on Google Earth and can be distorted . ( I don't normally use this so it isn't a problem). From what I can gather I am using vesa driver software with old NVIDIA hardware. The system>harware drivers recommends v96 NVIDIA driver - would Google Earth performance improve if I used this ?

I will wait for another day for any reply and then close this thread as solved.... Many thanks
Look at the last part of my last post. Google Earth would do better with the NVidia driver, because then it would use the onboard memory and functions... but would still be 2D without hardware accelrlation.

If you upgraded to Ubuntu 10.10, then you could use the Experimental 3D Driver which adds hardware acceleration... If you did go this way, I would backup your xorg.conf beforehand. This option would get you as fast and capable as you could get with the hardware "you" have. Anything better would require you to change/upgrade your GPU card to something more capable.

realzippy

September 27th, 2011, 08:30 AM

The system>harware drivers recommends v96 NVIDIA driver

....that is what I was asking when I wanted you to run
jockey-gtk which you ignored twice in this thread.
Jockey = additional drivers = hardware drivers ....

So,yes,the 96 driver should give you the best performance afaik.

jdneate

September 27th, 2011, 06:40 PM

I think I got out of step when "jockey-gtk" came up.

What does it do ?

I have a system which does what I want it to do -- so reluctant to try in case I lose it

realzippy

September 27th, 2011, 06:50 PM

...it starts the "hardware drivers" GUI from shell.
Nothing else...

MAFoElffen

September 27th, 2011, 07:02 PM

...it starts the "hardware drivers" GUI from shell.
Nothing else...
+1 Yes or go through the Menus:
System > Administration > Hardware Drivers

REMEMBER to make a copy of your xorg.conf to somewhere safe "before" you do that... you'll still need to readd your modeline changes to the new xorg.conf... It will get overwritten in the install.

jdneate

September 27th, 2011, 07:54 PM

MAFoElffen

September 27th, 2011, 08:22 PM

Right - I loaded the NVIDIA v96 driver via Administration>Hardware Drivers as part of the experimentation; I'm sure that the system did not run after restart.

Not knowing very much about Ubuntu/Linux .... Would the v96 driver generate it's own xorg.conf file and modify the GRUB loader to remove/add NOMODESET when it is installed ?

Having got an acceptable system I am reluctant to modify it unless I can understand what the implications are and how to get back to the working system should it not work !
Yes it will. During the install it will generate a new xorg.conf (ergo the need to backup your old one.) If it doesn't run

sudo nvidia-xconfig
***It may find the montitor modes or not- what your original assumption of the Monitor not storing the EDID data may have been correct (which we all assume was right). If so. it will fail until you add the modelines and changes from the old xorg.conf to the new one that was generated... Thats one of the reasons I asked you to backup the old one... You can cut and paste the changes in. Without those modelines and other changes, it will try "nvidia-auto-select +0+0" to probe the monitor for suitable modes from the EDID in the monitor // which doesn't work for your's, because there is not stored EDID data to use for that to work...

The other reason I had you backup the old one, was that if you don't like the new driver, you can overwrite the new xorg.conf with the backup xorg.conf and you will be right back to where you were... What tells X-Windows what driver to use and what settings to use for that driver... is the xorg.conf file.

If there is no xorg.conf file then Xorg goes into an "auto" mode, where it probes hardware, tries to find a suitable driver and uses default settings for it. It accepts other input from KMS to try to help with that. This doesn't always work and surely didn't for you in all resolutions.

*** By the by-- once that driver is installed and working, there is a way to confirm if your monitor has EDID data stored or not. In the nvidia-settings applet, there is an option to retrieve the EDID data of a monitor and an option you can use in the xorg.conf file to use an external custom edid file. If there was EDID data stored, then that file would contain hex data. If that file did come back as good, then you could use that data to use the full capabilities of that monitor... When that happens like that, sometimes (rarely) there was a problem in how it tried retrieving the data. When monitors and TV's first started storing that data, it wasn't universal and standardized.

If that file comes back as blank or 0 bytes, then it confirms that there was no stored data.

*** Installing the driver does not change any of the grub files.

jdneate

September 28th, 2011, 12:31 PM

Thanks for the explanation .....

I have activated the NVIDIA v96 driver ( system>admin>drivers). It seems to work and the display is faster when there are a lot of graphics.

The xorg.conf file is

spe@jdneate:~$ cat /etc/X11/xorg.conf

Section "Monitor"
Identifier "Configured Monitor"
HorizSync 31-60
VertRefresh 60-75
EndSection

Section "Screen"
Identifier "Default Screen"
Monitor "Configured Monitor"
Device "Configured Video Device"
DefaultDepth 24
Option "AddARGBGLXVisuals" "True"
EndSection

Section "Module"
Load "glx"
EndSection

Section "Device"
Identifier "Configured Video Device"
Driver "nvidia"
Option "NoLogo" "True"
EndSection

System>admin>preferences>monitors now gives the option to use either the Gnome or NVIDIA tools to display monitor detail. The Gnome tool shows 11 resolution options to 1024x768. The NVIDIA option shows a lot more detail and a lot of options around Xorg; the driver is on auto resolution detection and has chosen 1024x768. The resolution options include some above the capability of the monitor.

realzippy

September 28th, 2011, 02:18 PM

So this seems to have a happy end.
Have fun!

& remember to set thread as solved.

jdneate

October 1st, 2011, 09:25 PM

Only a partial happy ending - I have a robust working system which does all that I want.
Unfortunately I found that the NVIDIA v96 driver was not behaving; twice within 24hrs the system hung with a blank screen when changing users/shutting down. Also when typing commands using terminal, characters were often displayed as spaces. However, when the cursor was returned to the space the required character was displayed. I don't know if it is hardware; but in the end I deactivated v96 and went back to the VESA driver. The system works fine for what I use it !

Again thanks for your help.