PDA

View Full Version : [ubuntu] Huawei E372 mobile broadband



macgywer
June 19th, 2011, 09:12 PM
Hello!

Any idea how I can get the huawei e372 to be recognized by ubuntu 11.04, so i can connect to the internet?

Matbro
June 28th, 2011, 04:20 PM
Hi

Maybe this will work for you, my Huawei E367 was only discovered as a storage device in 11.04, though it worked perfectly in 10.10

After you connected your modem, run "lsusb" in a terminal and look for the huawei line. notice the xxxx:yyyy numbers

Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 002: ID 1d57:2400
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 007: ID 12d1:1506 Huawei Technologies Co., Ltd.
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

enter:
sudo modprobe usbserial vendor=0x12d1 product=0x1506 (replace with your numbers)

run "dmesg" and see if you get any TTY messages

usb 1-2: generic converter now attached to ttyUSB1
usbserial_generic 1-2:1.3: generic converter detected
usb 1-2: generic converter now attached to ttyUSB2

If you get similar result, the modem will be discovered in network manager (you have to enable "Enable Mobile Broadband" in the GUI)
/Mats

Bashar "
September 21st, 2011, 06:59 PM
Hi

Maybe this will work for you, my Huawei E367 was only discovered as a storage device in 11.04, though it worked perfectly in 10.10

After you connected your modem, run "lsusb" in a terminal and look for the huawei line. notice the xxxx:yyyy numbers

Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 002: ID 1d57:2400
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 007: ID 12d1:1506 Huawei Technologies Co., Ltd.
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

enter:
sudo modprobe usbserial vendor=0x12d1 product=0x1506 (replace with your numbers)

run "dmesg" and see if you get any TTY messages

usb 1-2: generic converter now attached to ttyUSB1
usbserial_generic 1-2:1.3: generic converter detected
usb 1-2: generic converter now attached to ttyUSB2

If you get similar result, the modem will be discovered in network manager (you have to enable "Enable Mobile Broadband" in the GUI)
/Mats


having same issue and didnt get the TTY mesages, my lsusb is:
Bus 002 Device 007: ID 12d1:1505 Huawei Technologies Co., Ltd.

and ran the command modprobe usbserial vendor=0x12d1 product=0x1505 as root but no luck

any other advises?

dave01945
September 21st, 2011, 07:16 PM
you could try this script it has always worked for me when the modem hasn't been detected properly it contains everything needed for mobile broadband

Sakis3g (http://www.sakis3g.org/)

just run it as


./sakis3g --interactive

Bashar "
September 21st, 2011, 07:23 PM
Thanks, but this solution solved it for me http://www.santinoli.com/open/e1692-howto.html

i just updated the numbers, so my usb_modeswitch.conf looks like this:


# Configuration for the usb_modeswitch package, a mode switching tool for
# USB devices providing multiple states or modes
#
# This file is evaluated by the wrapper script "usb_modeswitch_dispatcher"
# in /usr/sbin
# To enable an option, set it to "1", "yes" or "true" (case doesn't matter)
# Everything else counts as "disable"


# Disable automatic mode switching globally (e.g. to access the original
# install storage)

DisableSwitching=0


# Enable logging (results in a extensive report file in /var/log, named
# "usb_modeswitch_<interface-name>" (and probably others)

EnableLogging=1

# Huawei E372
DefaultVendor= 0x12d1
DefaultProduct= 0x1505

TargetVendor= 0x12d1
TargetProduct= 0x140c

MessageContent="55534243000000000000000000000011060000000000000000 000000000000"

CheckSuccess=5



then i run usb_modeswitch -c /etc/usb_modeswitch.conf

of course before that need to install usb_modeswitch using apt-get install usb-modeswitch

Thanks :)

alexfish
October 25th, 2011, 08:33 AM
excuse me, where can i pick the unlocked already E372 HUAWEI dongle? is there any1 take from mobile2wifi.co.uk? how about that?

unlock modems at own risk . can have a look here there is a bit about a Huawie device

http://www.pcurtis.com/ubuntu-mobile.htm ; if it goes wrong : Tuff

Bashar "
November 5th, 2011, 10:56 PM
Thanks, but this solution solved it for me http://www.santinoli.com/open/e1692-howto.html

i just updated the numbers, so my usb_modeswitch.conf looks like this:


# Configuration for the usb_modeswitch package, a mode switching tool for
# USB devices providing multiple states or modes
#
# This file is evaluated by the wrapper script "usb_modeswitch_dispatcher"
# in /usr/sbin
# To enable an option, set it to "1", "yes" or "true" (case doesn't matter)
# Everything else counts as "disable"


# Disable automatic mode switching globally (e.g. to access the original
# install storage)

DisableSwitching=0


# Enable logging (results in a extensive report file in /var/log, named
# "usb_modeswitch_<interface-name>" (and probably others)

EnableLogging=1

# Huawei E372
DefaultVendor= 0x12d1
DefaultProduct= 0x1505

TargetVendor= 0x12d1
TargetProduct= 0x140c

MessageContent="55534243000000000000000000000011060000000000000000 000000000000"

CheckSuccess=5



then i run usb_modeswitch -c /etc/usb_modeswitch.conf

of course before that need to install usb_modeswitch using apt-get install usb-modeswitch

Thanks :)


just to note after upgrading to 11.10 the device works out of the box without the need of the abve.

for those who might read this in future

alexfish
November 16th, 2011, 05:41 PM
any body has used the E586 huawei (http://www.mobile2wifi.co.uk/index.php?main_page=product_info&cPath=1&products_id=1) wifi router? does it works for Ubuntu system?

have started a new thread here

E586 huawei (mobile wifi router ) (http://ubuntuforums.org/showthread.php?t=1881919)

alexfish

axle88
February 2nd, 2012, 02:49 PM
Thanks, but this solution solved it for me http://www.santinoli.com/open/e1692-howto.html

i just updated the numbers, so my usb_modeswitch.conf looks like this:


# Configuration for the usb_modeswitch package, a mode switching tool for
# USB devices providing multiple states or modes
#
# This file is evaluated by the wrapper script "usb_modeswitch_dispatcher"
# in /usr/sbin
# To enable an option, set it to "1", "yes" or "true" (case doesn't matter)
# Everything else counts as "disable"


# Disable automatic mode switching globally (e.g. to access the original
# install storage)

DisableSwitching=0


# Enable logging (results in a extensive report file in /var/log, named
# "usb_modeswitch_<interface-name>" (and probably others)

EnableLogging=1

# Huawei E372
DefaultVendor= 0x12d1
DefaultProduct= 0x1505

TargetVendor= 0x12d1
TargetProduct= 0x140c

MessageContent="55534243000000000000000000000011060000000000000000 000000000000"

CheckSuccess=5



then i run usb_modeswitch -c /etc/usb_modeswitch.conf

of course before that need to install usb_modeswitch using apt-get install usb-modeswitch

Thanks :)


Hey all,

I work with a phidgets single board computer which runs a stripped down version of debian and am trying to install a huawei E 372 modem. I however
cannot get the modem to connect. I have tried using usbserial and usbmodeswitch but could not get it to work. Below are screen dumps describing whaat I have tried so far. Heres what I did:

vendor/product id's from lsusb

root@phidgetsbc:/# lsusb
Bus 001 Device 004: ID 12d1:1505 Huawei Technologies Co., Ltd. E398 LTE/UMTS/GSM Modem/Networkcard
Bus 001 Device 003: ID 06c2:0045 Phidgets Inc. (formerly GLAB) PhidgetInterface Kit 8-8-8
Bus 001 Device 002: ID 0451:2077 Texas Instruments, Inc. TUSB2077 Hub

I then ran this command:

modprobe usbserial vendor=0x12d1 product=0x1505

The following are the new lines from dmesg

usbserial: Unknown parameter `vendor'
usbserial: Unknown parameter `vendor'
usbcore: registered new interface driver usbserial
usbserial: USB Serial Driver core

Any idea why this could be happening?



I then tried another approach by trying to 'switch' the modem using usb_modeswitch. This failed with the following terminal output:

root@phidgetsbc:/# usb_modeswitch -c /usr/usbmode/usb-modeswitch-1.2.3/usb_modeswitch.conf
Looking for target devices ...
No devices in target mode or class found
Looking for default devices ...
found matching product ID
adding device
Found device in default mode, class or configuration (1)
Accessing device 004 on bus 001 ...
Getting the current device configuration ...
OK, got current device configuration (1)
Using first interface: 0x00
Using endpoints 0x01 (out) and 0x81 (in)
Inquiring device details; driver will be detached ...
Looking for active driver ...
OK, driver found ("usb-storage")
OK, driver "usb-storage" detached

SCSI inquiry data (for identification)
-------------------------
Vendor String: HUAWEI
Model String: Mass Storage
Revision String: 2.31
-------------------------

USB description data (for identification)
-------------------------
Manufacturer: Huawei Technologies
Product: HUAWEI Mobile
Serial No.: not provided
-------------------------
Setting up communication with interface 0
Using endpoint 0x01 for message sending ...
Trying to send message 1 to endpoint 0x01 ...
OK, message successfully sent
Resetting response endpoint 0x81
Could not reset endpoint (probably harmless): -62
Resetting message endpoint 0x01
Could not reset endpoint (probably harmless): -62
Device is gone, skipping any further commands

Checking for mode switch (max. 5 times, once per second) ...
Searching for target devices ...
Searching for target devices ...
Searching for target devices ...
Searching for target devices ...
Searching for target devices ...
No new devices in target mode or class found

Mode switch has failed. Bye.


Here are the new lines from dmesg after trying to switch the modem with usb-modeswitch.

usb 1-1.5: usbfs: process 1710 (usb_modeswitch) did not claim interface 0 before use
usb 1-1.5: USB disconnect, device number 4
usb 1-1.5: new full speed USB device number 5 using s3c2410-ohci
usb 1-1.5: New USB device found, idVendor=12d1, idProduct=14ac
usb 1-1.5: New USB device strings: Mfr=3, Product=2, SerialNumber=0
usb 1-1.5: Product: HUAWEI Mobile
usb 1-1.5: Manufacturer: Huawei Technologies
scsi2 : usb-storage 1-1.5:1.4
scsi3 : usb-storage 1-1.5:1.5
scsi 2:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2
scsi 3:0:0:0: Direct-Access HUAWEI TF CARD Storage 2.31 PQ: 0 ANSI: 2
sd 3:0:0:0: [sda] Attached SCSI removable disk


I hope this clears things up a bit. Theres probably something here that im just not seeing. Any help is greatly appreciated!

BTW I was able to install the modem on a desktop computer running debian. I also tried using the sakis3g script but this did not work either.

alexfish
February 3rd, 2012, 09:30 AM
can post results of these commands from the terminal, locate the lines which indicate the device and post only those lines


usb-devicesor

lsusb -t
and

lsusb -v

alexfish

axle88
February 3rd, 2012, 02:03 PM
can post results of these commands from the terminal, locate the lines which indicate the device and post only those lines


usb-devicesor

lsusb -t
and

lsusb -v

alexfish

Heres what I got from usb-devices

T: Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 4 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=12d1 ProdID=1505 Rev=00.00
S: Manufacturer=Huawei Technologies
S: Product=HUAWEI Mobile
C: #Ifs= 2 Cfg#= 1 Atr=c0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
I: If#= 1 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage

and here is the output from lsusb -v

Bus 001 Device 004: ID 12d1:1505 Huawei Technologies Co., Ltd. E398 LTE/UMTS/GSM Modem/Networkcard
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x12d1 Huawei Technologies Co., Ltd.
idProduct 0x1505 E398 LTE/UMTS/GSM Modem/Networkcard
bcdDevice 0.00
iManufacturer 3 Huawei Technologies
iProduct 2 HUAWEI Mobile
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 55
bNumInterfaces 2
bConfigurationValue 1
iConfiguration 1 Huawei Configuration
bmAttributes 0xc0
Self Powered
MaxPower 500mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 8 Mass Storage
bInterfaceSubClass 6 SCSI
bInterfaceProtocol 80 Bulk (Zip)
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 8 Mass Storage
bInterfaceSubClass 6 SCSI
bInterfaceProtocol 80 Bulk (Zip)
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0000
(Bus Powered)

alexfish
February 4th, 2012, 03:43 PM
from previous posts when you ran the usb_modeswitch the device is switching from "1505" to "14ac"

switch the device to be seen as "14ac" .post the results of


usb-devices locate the lines which indicate the modem and only those lines


grep usb /sys/bus/usb/devices/*/modalias | grep p14acNoted:
from your switching data , the only reason for a fail reply is your device is not listed


################################################## ######
# Huawei EC156

DefaultVendor= 0x12d1
DefaultProduct=0x1505

TargetVendor= 0x12d1
TargetProduct= 0x140b

MessageContent="55534243123456780000000000000011062000000100000000 000000000000"

CheckSuccess=20a config with more than one target product looks like

]################################################## ######

# Huawei EC156

DefaultVendor= 0x12d1
DefaultProduct=0x1505

TargetVendor= 0x12d1
TargetProductList= 0x140b,14ac

MessageContent="55534243123456780000000000000011062000000100000000 000000000000"

CheckSuccess=20do not update the config data files .until we can see a driver loading , hence the above request to switch the device as is , then post the requested data , may prove the Messagecontent is correct.

alexfish

manish671
February 5th, 2012, 06:37 AM
Thanks everybody. I use Huawei UMG1831. It worked for me in just 2 steps

1 Following change in /etc/usb_modeswitch.conf
EnableLogging=1 # earlier it was 0
# Huawei UMG1831
DefaultVendor= 0x12d1
DefaultProduct= 0x1446
TargetVendor= 0x12d1
TargetProduct= 0x1404
MessageContent="55534243123456780000000000000011060000000000000000 000000000000"

2 sudo usb_modeswitch -c /etc/usb_modeswitch.conf
it said many things then bye. Immediately Network manager recognized the modem.

After new Ubuntu installation Ubuntu automatically recognized the modem but then in 2-3 hours it went off and no luck. So I started using mobilepartner and it was working fine except that Software Center could not recognize the net-connection. I was able to browse and do updates from terminal or package manager but not from Software center.

One can find target product and messageContenet from here
a) http://www.dd-wrt.com/wiki/index.php/3G_/_3.5G and
b) www.sakis3g.org/ download sakis3g then untar and look in folder sais3g/dependencies/usb-modeswitch-data/usbmodeswitch.d/ I tried to work with sakis but during installation it gave message that dependencies could not be met.

Again thanks everybody.

axle88
February 6th, 2012, 01:00 PM
from previous posts when you ran the usb_modeswitch the device is switching from "1505" to "14ac"

switch the device to be seen as "14ac" .post the results.


alexfish

Hey alexfish,

I first switched the modem to product id 14ac. Below is the output from usb-devices.

T: Bus=01 Lev=02 Prnt=02 Port=04 Cnt=01 Dev#= 5 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=12d1 ProdID=14ac Rev=00.00
S: Manufacturer=Huawei Technologies
S: Product=HUAWEI Mobile
C: #Ifs= 6 Cfg#= 1 Atr=c0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
I: If#= 5 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage

I then ran the second command that you suggested. Below is the output.

root@phidgetsbc:/# grep usb /sys/bus/usb/devices/*/modalias
/sys/bus/usb/devices/1-0:1.0/modalias:usb:v1D6Bp0001d0301dc09dsc00dp00ic09isc00 ip00
/sys/bus/usb/devices/1-1.5:1.0/modalias:usb:v12D1p14ACd0000dc00dsc00dp00icFFiscFF ipFF
/sys/bus/usb/devices/1-1.5:1.1/modalias:usb:v12D1p14ACd0000dc00dsc00dp00icFFiscFF ipFF
/sys/bus/usb/devices/1-1.5:1.2/modalias:usb:v12D1p14ACd0000dc00dsc00dp00icFFiscFF ipFF
/sys/bus/usb/devices/1-1.5:1.3/modalias:usb:v12D1p14ACd0000dc00dsc00dp00icFFiscFF ipFF
/sys/bus/usb/devices/1-1.5:1.4/modalias:usb:v12D1p14ACd0000dc00dsc00dp00ic08isc06 ip50
/sys/bus/usb/devices/1-1.5:1.5/modalias:usb:v12D1p14ACd0000dc00dsc00dp00ic08isc06 ip50
/sys/bus/usb/devices/1-1.7:1.0/modalias:usb:v06C2p0045d0903dc00dsc00dp00ic03isc00 ip00
/sys/bus/usb/devices/1-1:1.0/modalias:usb:v0451p2077d0100dc09dsc00dp00ic09isc00 ip00

barong234
February 6th, 2012, 08:11 PM
package you gonna need is modeswitch (for flip-flop USB Devices), wvdial (modem dialer). check your device by issuing command lsusb. if the device known as CD-ROM eject it, then issue anoter lsusb.
after that, configure your modeswitch and made dialer with wvdial.

manish671
February 7th, 2012, 03:30 AM
If it is Huawei E372 then target should be 12d1:1506
Thanks.

alexfish
February 7th, 2012, 03:33 PM
Hi axle88

ok the device is switching but not sure if correct message content is been sent

but no driver is loading as seen in

T: Bus=01 Lev=02 Prnt=02 Port=04 Cnt=01 Dev#= 5 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=12d1 ProdID=14ac Rev=00.00
S: Manufacturer=Huawei Technologies
S: Product=HUAWEI Mobile
C: #Ifs= 6 Cfg#= 1 Atr=c0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
I: If#= 5 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storagethe device lists as using the option module

can see if your kernel lists with this command

grep -i v12D1p14AC /lib/modules/`uname -r`/modules.aliasso send the command with

sudo modprobe optionif the device not listed with the grep command , need to send another command
echo "12d1 14ac" >/sys/bus/usb/drivers/option/module/drivers/usb-serial:option1/new_idthen see if the driver is loading with the command

usb-devicesthe next problem may be modem manager picking the correct port , look as could be ttyUSB0 or ttyUSB1
if Network Manager will configure the device all is good, if not then can use ppp directly

see what happens in Network Manager first , if met with failure , then can look at configuring ppp
and will also need further info about this device, this will hopefully help others to get connected

wvdial should not be necessary for these types of devices.

alexfish

alexfish
February 22nd, 2012, 03:43 PM
Have done some follow up info about these new Huawie devices in the a :How To

RE:How To : Mobile Broadband Connections [ Ubuntu 11.04 : 10.10 : 10.04 : 9.10] (http://ubuntuforums.org/showthread.php?t=1466490)

May also apply to 11.10

suggest reading all of first post + the links Regarding Huawei Mobile Partner + the Driver

Also note any links to USB MODSWITCH FORUM , Some of these Devices have "TWO MODES" so require TWO different switching messages , one two use standard 3g and one two switch the device to 4g Mode or WiFi
if switching to 4g mode or WiFi , presently you will need the linux driver from Huawie . RE Huawei Mobile Partner + the Driver

alexfish

hfdragon
September 5th, 2012, 03:19 PM
Hello,

I have a new E372.. and also have problems to make it functionnal.

If the modem is plugged at boot time, it's working (switching) ok.

If not, it seems it's not switching to modem mode.

Anyone has a solution ? (Using Ubuntu 12.04 and USB 3.0)

Thanks ins advance for your answers.