stembot
May 12th, 2011, 08:51 PM
Wireless connects fine, then disconnects regularly.
I thought it might be an issue with the rt2870sta driver, so I blacklisted it, and it uses rt2800usb now:
[ 13.625932] rt2870sta: module is from the staging directory, the quality is unknown, you have been warned.
[ 13.633139] usbcore: registered new interface driver rt2870
[ 15.039402] <==== rt28xx_init, Status=0
[ 15.992646] <==== rt28xx_init, Status=0
[ 158.339701] <==== rt28xx_init, Status=0
[ 278.340464] <==== rt28xx_init, Status=0
[ 3818.454594] <==== rt28xx_init, Status=0
[ 3978.559264] <==== rt28xx_init, Status=0
[ 4798.619302] usbcore: registered new interface driver rt2800usb
[ 4824.850590] <==== rt28xx_init, Status=0
[ 4998.593628] <==== rt28xx_init, Status=0
[ 5498.403411] <==== rt28xx_init, Status=0
[ 7218.359003] <==== rt28xx_init, Status=0
[ 9981.717499] <==== rt28xx_init, Status=0
[ 9982.777617] <==== rt28xx_init, Status=0
[10201.900447] <==== rt28xx_init, Status=0
[11024.395776] <==== rt28xx_init, Status=0
[11244.390883] <==== rt28xx_init, Status=0
[11324.381487] <==== rt28xx_init, Status=0
[11364.634246] <==== rt28xx_init, Status=0
[11464.394932] <==== rt28xx_init, Status=0
[12144.357259] <==== rt28xx_init, Status=0
[12264.633888] <==== rt28xx_init, Status=0
[12464.394894] <==== rt28xx_init, Status=0
[12724.414488] <==== rt28xx_init, Status=0
[12864.369764] <==== rt28xx_init, Status=0
[12970.530938] <==== rt28xx_init, Status=0
[12971.393951] <==== rt28xx_init, Status=0
[13292.433182] <==== rt28xx_init, Status=0
iwconfig:
wlan0 Ralink STA ESSID:"xxxxxx" Nickname:"RT2870STA"
Mode:Managed Frequency=2.437 GHz Access Point: 10:8C:CF:44:DA:C0
Bit Rate=54 Mb/s
RTS thr:off Fragment thr:off
Link Quality=100/100 Signal level:-57 dBm Noise level:-83 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
lsusb:
Bus 002 Device 005: ID 07d1:3c16 D-Link System
I haven't found anyone with this specific issue with solutions.
Any help is appreciated!
I thought it might be an issue with the rt2870sta driver, so I blacklisted it, and it uses rt2800usb now:
[ 13.625932] rt2870sta: module is from the staging directory, the quality is unknown, you have been warned.
[ 13.633139] usbcore: registered new interface driver rt2870
[ 15.039402] <==== rt28xx_init, Status=0
[ 15.992646] <==== rt28xx_init, Status=0
[ 158.339701] <==== rt28xx_init, Status=0
[ 278.340464] <==== rt28xx_init, Status=0
[ 3818.454594] <==== rt28xx_init, Status=0
[ 3978.559264] <==== rt28xx_init, Status=0
[ 4798.619302] usbcore: registered new interface driver rt2800usb
[ 4824.850590] <==== rt28xx_init, Status=0
[ 4998.593628] <==== rt28xx_init, Status=0
[ 5498.403411] <==== rt28xx_init, Status=0
[ 7218.359003] <==== rt28xx_init, Status=0
[ 9981.717499] <==== rt28xx_init, Status=0
[ 9982.777617] <==== rt28xx_init, Status=0
[10201.900447] <==== rt28xx_init, Status=0
[11024.395776] <==== rt28xx_init, Status=0
[11244.390883] <==== rt28xx_init, Status=0
[11324.381487] <==== rt28xx_init, Status=0
[11364.634246] <==== rt28xx_init, Status=0
[11464.394932] <==== rt28xx_init, Status=0
[12144.357259] <==== rt28xx_init, Status=0
[12264.633888] <==== rt28xx_init, Status=0
[12464.394894] <==== rt28xx_init, Status=0
[12724.414488] <==== rt28xx_init, Status=0
[12864.369764] <==== rt28xx_init, Status=0
[12970.530938] <==== rt28xx_init, Status=0
[12971.393951] <==== rt28xx_init, Status=0
[13292.433182] <==== rt28xx_init, Status=0
iwconfig:
wlan0 Ralink STA ESSID:"xxxxxx" Nickname:"RT2870STA"
Mode:Managed Frequency=2.437 GHz Access Point: 10:8C:CF:44:DA:C0
Bit Rate=54 Mb/s
RTS thr:off Fragment thr:off
Link Quality=100/100 Signal level:-57 dBm Noise level:-83 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
lsusb:
Bus 002 Device 005: ID 07d1:3c16 D-Link System
I haven't found anyone with this specific issue with solutions.
Any help is appreciated!