bludy
February 10th, 2010, 07:13 PM
I did an update during a time when power was cycling due do a nasty snow storm, but I'm pretty sure the update was completed successfully before I lost power. What did happen though is that my BIOS setup was reset.
Now if my HP Laserjet 1020 is plugged into USB during boot all other USB devices freeze for a while. So I played with my BIOS setting for USB:
- Enabled V1.1 and V2.0
- Disabled System USB Shadowing
So now my bootup doesn't hang. But now when I actually go into Karmic I still can't print.
dmesg shows the following:
[ 205.940008] usb 1-10: new high speed USB device using ehci_hcd and address 9
[ 219.510026] hub 1-0:1.0: unable to enumerate USB device on port 10
[ 223.430008] usb 1-10: new high speed USB device using ehci_hcd and address 10
[ 223.600766] usb 1-10: configuration #1 chosen from 1 choice
[ 223.604896] usblp0: USB Bidirectional printer dev 10 if 0 alt 0 proto 2 vid 0x03F0 pid 0x2B17
[ 224.780817] usb 1-10: usbfs: interface 0 claimed by usblp while 'usb' sets config #1
[ 229.660155] usb 1-10: usbfs: USBDEVFS_CONTROL failed cmd hp rqt 128 rq 6 len 255 ret -110
[ 230.000138] usb 1-10: usbfs: USBDEVFS_CONTROL failed cmd python rqt 128 rq 6 len 255 ret -110
[ 247.100044] usb 1-10: usbfs: USBDEVFS_CONTROL failed cmd hp rqt 128 rq 6 len 255 ret -110
[ 354.130146] usb 1-10: usbfs: USBDEVFS_CONTROL failed cmd hp rqt 128 rq 6 len 255 ret -110
[ 433.206810] usb 1-10: usbfs: interface 0 claimed by usblp while 'usb' sets config #1
[ 438.190170] usb 1-10: usbfs: USBDEVFS_CONTROL failed cmd hp rqt 128 rq 6 len 255 ret -110
[ 438.410164] usb 1-10: usbfs: USBDEVFS_CONTROL failed cmd python rqt 128 rq 6 len 255 ret -110
[ 443.190068] usb 1-10: usbfs: USBDEVFS_CONTROL failed cmd hp rqt 128 rq 6 len 255 ret -110
[ 443.410063] usb 1-10: usbfs: USBDEVFS_CONTROL failed cmd python rqt 128 rq 6 len 255 ret -110
[ 448.190220] usb 1-10: usbfs: USBDEVFS_CONTROL failed cmd hp rqt 128 rq 6 len 255 ret -110
[ 448.414887] usb 1-10: usbfs: USBDEVFS_CONTROL failed cmd python rqt 128 rq 6 len 255 ret -110
[ 500.870143] usb 1-10: usbfs: USBDEVFS_CONTROL failed cmd python rqt 128 rq 6 len 255 ret -110
[ 505.870039] usb 1-10: usbfs: USBDEVFS_CONTROL failed cmd python rqt 128 rq 6 len 255 ret -110
[ 510.870064] usb 1-10: usbfs: USBDEVFS_CONTROL failed cmd python rqt 128 rq 6 len 255 ret -110
[ 668.480052] usb 1-10: usbfs: USBDEVFS_CONTROL failed cmd hp rqt 128 rq 6 len 255 ret -110
[ 978.480044] usb 1-10: usbfs: USBDEVFS_CONTROL failed cmd hp rqt 128 rq 6 len 255 ret -110
[ 1288.470103] usb 1-10: usbfs: USBDEVFS_CONTROL failed cmd hp rqt 128 rq 6 len 255 ret -110
[ 1598.210070] usb 1-10: usbfs: USBDEVFS_CONTROL failed cmd hp rqt 128 rq 6 len 255 ret -110
/var/log/messages shows this:
Feb 10 12:58:44 localhost foo2zjs-wrapper: foo2zjs-wrapper -P -z1 -L0 -r1200x600 -p1 -m1 -s7
Feb 10 12:58:45 localhost foo2zjs-wrapper: gs -sPAPERSIZE=letter -g10200x6600 -r1200x600 -sDEVICE=pbmraw -dCOLORSCREEN -dMaxBitmap=500000000
Feb 10 12:58:45 localhost foo2zjs-wrapper: foo2zjs -r1200x600 -g10200x6600 -p1 -m1 -n1 -d1 -s7 -z1 -u 192x96 -l 192x96 -L 0 -P
cups shows the following error:
D [10/Feb/2010:12:58:50 -0500] [Job 542] prnt/backend/hp.c 720: ERROR: cannot open device stat=12: hp:/usb/HP_LaserJet_1020?serial=FN1DEW2
D [10/Feb/2010:12:58:50 -0500] [Job 542] Backend returned status 1 (failed)
D [10/Feb/2010:12:58:50 -0500] [Job 542] End of messages
D [10/Feb/2010:12:58:50 -0500] [Job 542] printer-state=3(idle)
D [10/Feb/2010:12:58:50 -0500] [Job 542] printer-state-message="/usr/lib/cups/backend/hp failed"
D [10/Feb/2010:12:58:50 -0500] [Job 542] printer-state-reasons=none
I tried changing kernels but the same problem is there. When I unplug the printer this error goes away. My gut says that USB 2.0 is not working anymore but I can't verify it.
I'm on an AMD64 Athlon CPU.
Help?
Now if my HP Laserjet 1020 is plugged into USB during boot all other USB devices freeze for a while. So I played with my BIOS setting for USB:
- Enabled V1.1 and V2.0
- Disabled System USB Shadowing
So now my bootup doesn't hang. But now when I actually go into Karmic I still can't print.
dmesg shows the following:
[ 205.940008] usb 1-10: new high speed USB device using ehci_hcd and address 9
[ 219.510026] hub 1-0:1.0: unable to enumerate USB device on port 10
[ 223.430008] usb 1-10: new high speed USB device using ehci_hcd and address 10
[ 223.600766] usb 1-10: configuration #1 chosen from 1 choice
[ 223.604896] usblp0: USB Bidirectional printer dev 10 if 0 alt 0 proto 2 vid 0x03F0 pid 0x2B17
[ 224.780817] usb 1-10: usbfs: interface 0 claimed by usblp while 'usb' sets config #1
[ 229.660155] usb 1-10: usbfs: USBDEVFS_CONTROL failed cmd hp rqt 128 rq 6 len 255 ret -110
[ 230.000138] usb 1-10: usbfs: USBDEVFS_CONTROL failed cmd python rqt 128 rq 6 len 255 ret -110
[ 247.100044] usb 1-10: usbfs: USBDEVFS_CONTROL failed cmd hp rqt 128 rq 6 len 255 ret -110
[ 354.130146] usb 1-10: usbfs: USBDEVFS_CONTROL failed cmd hp rqt 128 rq 6 len 255 ret -110
[ 433.206810] usb 1-10: usbfs: interface 0 claimed by usblp while 'usb' sets config #1
[ 438.190170] usb 1-10: usbfs: USBDEVFS_CONTROL failed cmd hp rqt 128 rq 6 len 255 ret -110
[ 438.410164] usb 1-10: usbfs: USBDEVFS_CONTROL failed cmd python rqt 128 rq 6 len 255 ret -110
[ 443.190068] usb 1-10: usbfs: USBDEVFS_CONTROL failed cmd hp rqt 128 rq 6 len 255 ret -110
[ 443.410063] usb 1-10: usbfs: USBDEVFS_CONTROL failed cmd python rqt 128 rq 6 len 255 ret -110
[ 448.190220] usb 1-10: usbfs: USBDEVFS_CONTROL failed cmd hp rqt 128 rq 6 len 255 ret -110
[ 448.414887] usb 1-10: usbfs: USBDEVFS_CONTROL failed cmd python rqt 128 rq 6 len 255 ret -110
[ 500.870143] usb 1-10: usbfs: USBDEVFS_CONTROL failed cmd python rqt 128 rq 6 len 255 ret -110
[ 505.870039] usb 1-10: usbfs: USBDEVFS_CONTROL failed cmd python rqt 128 rq 6 len 255 ret -110
[ 510.870064] usb 1-10: usbfs: USBDEVFS_CONTROL failed cmd python rqt 128 rq 6 len 255 ret -110
[ 668.480052] usb 1-10: usbfs: USBDEVFS_CONTROL failed cmd hp rqt 128 rq 6 len 255 ret -110
[ 978.480044] usb 1-10: usbfs: USBDEVFS_CONTROL failed cmd hp rqt 128 rq 6 len 255 ret -110
[ 1288.470103] usb 1-10: usbfs: USBDEVFS_CONTROL failed cmd hp rqt 128 rq 6 len 255 ret -110
[ 1598.210070] usb 1-10: usbfs: USBDEVFS_CONTROL failed cmd hp rqt 128 rq 6 len 255 ret -110
/var/log/messages shows this:
Feb 10 12:58:44 localhost foo2zjs-wrapper: foo2zjs-wrapper -P -z1 -L0 -r1200x600 -p1 -m1 -s7
Feb 10 12:58:45 localhost foo2zjs-wrapper: gs -sPAPERSIZE=letter -g10200x6600 -r1200x600 -sDEVICE=pbmraw -dCOLORSCREEN -dMaxBitmap=500000000
Feb 10 12:58:45 localhost foo2zjs-wrapper: foo2zjs -r1200x600 -g10200x6600 -p1 -m1 -n1 -d1 -s7 -z1 -u 192x96 -l 192x96 -L 0 -P
cups shows the following error:
D [10/Feb/2010:12:58:50 -0500] [Job 542] prnt/backend/hp.c 720: ERROR: cannot open device stat=12: hp:/usb/HP_LaserJet_1020?serial=FN1DEW2
D [10/Feb/2010:12:58:50 -0500] [Job 542] Backend returned status 1 (failed)
D [10/Feb/2010:12:58:50 -0500] [Job 542] End of messages
D [10/Feb/2010:12:58:50 -0500] [Job 542] printer-state=3(idle)
D [10/Feb/2010:12:58:50 -0500] [Job 542] printer-state-message="/usr/lib/cups/backend/hp failed"
D [10/Feb/2010:12:58:50 -0500] [Job 542] printer-state-reasons=none
I tried changing kernels but the same problem is there. When I unplug the printer this error goes away. My gut says that USB 2.0 is not working anymore but I can't verify it.
I'm on an AMD64 Athlon CPU.
Help?