Kojans
December 4th, 2009, 09:12 PM
Hi!
I cannot get a working wireless connection from my laptop (HP compaq nc6000) with the wireless USB adaptor from Linksys: WUSB54GC v.3. I think the adaptor is recognised: I got this output from /var/log/messages after plugging in the adaptor:
Dec 4 20:39:36 ko-laptop kernel: [ 6375.868085] usb 1-1: new high speed USB device using ehci_hcd and address 4
Dec 4 20:39:36 ko-laptop kernel: [ 6376.018110] usb 1-1: configuration #1 chosen from 1 choice
Dec 4 20:39:36 ko-laptop kernel: [ 6376.057957] Registered led device: rt2800usb-phy1::radio
Dec 4 20:39:36 ko-laptop kernel: [ 6376.057985] Registered led device: rt2800usb-phy1::assoc
Dec 4 20:39:36 ko-laptop kernel: [ 6376.058013] Registered led device: rt2800usb-phy1::quality
Dec 4 20:39:36 ko-laptop kernel: [ 6376.119286] udev: renamed network interface wlan0 to wlan1
Dec 4 20:39:36 ko-laptop kernel: [ 6376.123172] rt2800usb 1-1:1.0: firmware: requesting rt2870.bin
Dec 4 20:39:36 ko-laptop kernel: [ 6376.370193] ADDRCONF(NETDEV_UP): wlan1: link is not ready
from iwconfig:
ko@ko-laptop:~$ iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
irda0 no wireless extensions.
wmaster0 no wireless extensions.
wlan1 IEEE 802.11bgn ESSID:""
Mode:Managed Frequency:2.412 GHz Access Point: Not-Associated
Tx-Power=14 dBm
Retry long limit:7 RTS thr: off Fragment thr: off
Power Management: on
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 MissedNetworkManager Applet beacon:0
I have Ubuntu 9-10 installed, and (tried to) use the NetworkManager Applet to configure network access. My router is a SpeedTouch THOMSON ST780; I can get a wireless connection from Windows XP.
My questions:
Do I need to download a driver?
From Where/which driver?
Do I have to install ndiswrapper?
Any help would be appreciated; I found a lot of posts about wireless connections, but none of them could make me any wiser...
Thanks!
I cannot get a working wireless connection from my laptop (HP compaq nc6000) with the wireless USB adaptor from Linksys: WUSB54GC v.3. I think the adaptor is recognised: I got this output from /var/log/messages after plugging in the adaptor:
Dec 4 20:39:36 ko-laptop kernel: [ 6375.868085] usb 1-1: new high speed USB device using ehci_hcd and address 4
Dec 4 20:39:36 ko-laptop kernel: [ 6376.018110] usb 1-1: configuration #1 chosen from 1 choice
Dec 4 20:39:36 ko-laptop kernel: [ 6376.057957] Registered led device: rt2800usb-phy1::radio
Dec 4 20:39:36 ko-laptop kernel: [ 6376.057985] Registered led device: rt2800usb-phy1::assoc
Dec 4 20:39:36 ko-laptop kernel: [ 6376.058013] Registered led device: rt2800usb-phy1::quality
Dec 4 20:39:36 ko-laptop kernel: [ 6376.119286] udev: renamed network interface wlan0 to wlan1
Dec 4 20:39:36 ko-laptop kernel: [ 6376.123172] rt2800usb 1-1:1.0: firmware: requesting rt2870.bin
Dec 4 20:39:36 ko-laptop kernel: [ 6376.370193] ADDRCONF(NETDEV_UP): wlan1: link is not ready
from iwconfig:
ko@ko-laptop:~$ iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
irda0 no wireless extensions.
wmaster0 no wireless extensions.
wlan1 IEEE 802.11bgn ESSID:""
Mode:Managed Frequency:2.412 GHz Access Point: Not-Associated
Tx-Power=14 dBm
Retry long limit:7 RTS thr: off Fragment thr: off
Power Management: on
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 MissedNetworkManager Applet beacon:0
I have Ubuntu 9-10 installed, and (tried to) use the NetworkManager Applet to configure network access. My router is a SpeedTouch THOMSON ST780; I can get a wireless connection from Windows XP.
My questions:
Do I need to download a driver?
From Where/which driver?
Do I have to install ndiswrapper?
Any help would be appreciated; I found a lot of posts about wireless connections, but none of them could make me any wiser...
Thanks!