PDA

View Full Version : [ubuntu] Can not install ubuntu 9.04 seagate sata Hard disk (sata_sil module not found)



rofoeagle
May 12th, 2009, 09:23 PM
Hi
I am trying to install ubuntu 9.04 on a Laptop Toshiba Model M100-SP with HDD Seagate 100 GB SATA...

The problem is that the installer could not detect the sata hard disk... I think the problem is because the kernel 2.26.28-11-generic (ubuntu 9.04) doesn't have the sata_sil module.

I have tried to load it manually with modprobe -i sata_sil and modprobe -i libata but the modules were not found!!!


Please any advice? I need your help ... What can I do?


this is the information:


LSHW
*-ide:0
description: IDE interface
product: IXP SB400 Serial ATA Controller
vendor: ATI Technologies Inc
physical id: 12
bus info: pci@0000:00:12.0
logical name: scsi0
version: 80
width: 32 bits
clock: 66MHz
capabilities: ide pm msi bus_master cap_list emulated
configuration: driver=sata_sil latency=64 module=sata_sil
*-disk
description: ATA Disk
product: ST9100821AS
vendor: Seagate
physical id: 0.0.0
bus info: scsi@0:0.0.0
logical name: /dev/sda
version: 3.AA
serial: 5NJ0FB9G
size: 93GiB (100GB)
configuration: ansiversion=5



HDPARM
/dev/sda:

Model=ST9100821AS , FwRev=3.AAB , SerialNo= 5NJ0FB9G
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=8192kB, MaxMultSect=16, MultSect=?16?
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=195371568
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5 udma6
AdvancedPM=yes: unknown setting WriteCache=enabled
Drive conforms to: Unspecified: ATA/ATAPI-1,2,3,4,5,6,7

* signifies the current active mode




LSPCI
00:00.0 Host bridge [0600]: ATI Technologies Inc Device [1002:5a31] (rev 01)
00:01.0 PCI bridge [0604]: ATI Technologies Inc RS480 PCI Bridge [1002:5a3f]
00:06.0 PCI bridge [0604]: ATI Technologies Inc RS480 PCI Bridge [1002:5a38]
00:12.0 IDE interface [0101]: ATI Technologies Inc IXP SB400 Serial ATA Controller [1002:4379] (rev 80)
00:13.0 USB Controller [0c03]: ATI Technologies Inc IXP SB400 USB Host Controller [1002:4374] (rev 80)
00:13.1 USB Controller [0c03]: ATI Technologies Inc IXP SB400 USB Host Controller [1002:4375] (rev 80)
00:13.2 USB Controller [0c03]: ATI Technologies Inc IXP SB400 USB2 Host Controller [1002:4373] (rev 80)
00:14.0 SMBus [0c05]: ATI Technologies Inc IXP SB400 SMBus Controller [1002:4372] (rev 82)
00:14.1 IDE interface [0101]: ATI Technologies Inc IXP SB400 IDE Controller [1002:4376] (rev 80)
00:14.2 Audio device [0403]: ATI Technologies Inc IXP SB4x0 High Definition Audio Controller [1002:437b] (rev 01)
00:14.3 ISA bridge [0601]: ATI Technologies Inc IXP SB400 PCI-ISA Bridge [1002:4377] (rev 80)
00:14.4 PCI bridge [0604]: ATI Technologies Inc IXP SB400 PCI-PCI Bridge [1002:4371] (rev 80)
01:05.0 VGA compatible controller [0300]: ATI Technologies Inc RC410 [Radeon Xpress 200M] [1002:5a62]
02:00.0 Ethernet controller [0200]: Atheros Communications Inc. AR242x 802.11abg Wireless PCI Express Adapter [168c:001c] (rev 01)
09:04.0 CardBus bridge [0607]: ENE Technology Inc CB1410 Cardbus Controller [1524:1410] (rev 01)
09:06.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ [10ec:8139] (rev 10)




DMESG
a 4096 in
[ 12.103851] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 12.103962] ata1.00: status: { DRDY ERR }
[ 12.104014] ata1.00: error: { ABRT }
[ 12.128659] ata1.00: configured for UDMA/100
[ 12.128668] ata1: EH complete
[ 12.275590] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 12.275641] ata1.00: BMDMA2 stat 0x82d0009
[ 12.275692] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 12.275693] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 12.275804] ata1.00: status: { DRDY ERR }
[ 12.275851] ata1.00: error: { ABRT }
[ 12.300648] ata1.00: configured for UDMA/100
[ 12.300657] ata1: EH complete
[ 12.447641] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 12.447692] ata1.00: BMDMA2 stat 0x82d0009
[ 12.447744] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 12.447745] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 12.447855] ata1.00: status: { DRDY ERR }
[ 12.447903] ata1.00: error: { ABRT }
[ 12.472647] ata1.00: configured for UDMA/100
[ 12.472656] ata1: EH complete
[ 12.619591] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 12.619642] ata1.00: BMDMA2 stat 0x82d0009
[ 12.619694] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 12.619695] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 12.619806] ata1.00: status: { DRDY ERR }
[ 12.619854] ata1.00: error: { ABRT }
[ 12.644648] ata1.00: configured for UDMA/100
[ 12.644658] ata1: EH complete
[ 12.791640] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 12.791691] ata1.00: BMDMA2 stat 0x82d0009
[ 12.791742] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 12.791744] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 12.791854] ata1.00: status: { DRDY ERR }
[ 12.791902] ata1.00: error: { ABRT }
[ 12.816649] ata1.00: configured for UDMA/100
[ 12.816658] ata1: EH complete
[ 12.963588] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 12.963639] ata1.00: BMDMA2 stat 0x82d0009
[ 12.963690] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 12.963692] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 12.963802] ata1.00: status: { DRDY ERR }
[ 12.963849] ata1.00: error: { ABRT }
[ 12.988647] ata1.00: configured for UDMA/100
[ 12.988656] sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
[ 12.988660] sd 0:0:0:0: [sda] Sense Key : Aborted Command [current] [descriptor]
[ 12.988665] Descriptor sense data with sense descriptors (in hex):
[ 12.988667] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 12.988677] 00 00 00 00
[ 12.988681] sd 0:0:0:0: [sda] Add. Sense: No additional sense information
[ 12.988686] end_request: I/O error, dev sda, sector 0
[ 12.988736] Buffer I/O error on device sda, logical block 0
[ 12.988791] ata1: EH complete
[ 13.135745] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 13.135795] ata1.00: BMDMA2 stat 0x82d0009
[ 13.135847] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 13.135848] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 13.135959] ata1.00: status: { DRDY ERR }
[ 13.136012] ata1.00: error: { ABRT }
[ 13.160648] ata1.00: configured for UDMA/100
[ 13.160657] ata1: EH complete
[ 13.307587] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 13.307638] ata1.00: BMDMA2 stat 0x82d0009
[ 13.307689] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 13.307691] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 13.307801] ata1.00: status: { DRDY ERR }
[ 13.307849] ata1.00: error: { ABRT }
[ 13.332648] ata1.00: configured for UDMA/100
[ 13.332657] ata1: EH complete
[ 13.479638] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 13.479689] ata1.00: BMDMA2 stat 0x82d0009
[ 13.479740] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 13.479742] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 13.479852] ata1.00: status: { DRDY ERR }
[ 13.479900] ata1.00: error: { ABRT }
[ 13.504648] ata1.00: configured for UDMA/100
[ 13.504657] ata1: EH complete
[ 13.651585] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 13.651636] ata1.00: BMDMA2 stat 0x82d0009
[ 13.651688] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 13.651689] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 13.651799] ata1.00: status: { DRDY ERR }
[ 13.651847] ata1.00: error: { ABRT }
[ 13.676645] ata1.00: configured for UDMA/100
[ 13.676654] ata1: EH complete
[ 13.823636] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 13.823687] ata1.00: BMDMA2 stat 0x82d0009
[ 13.823738] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 13.823740] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 13.823850] ata1.00: status: { DRDY ERR }
[ 13.823898] ata1.00: error: { ABRT }
[ 13.848645] ata1.00: configured for UDMA/100
[ 13.848654] ata1: EH complete
[ 13.995592] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 13.995643] ata1.00: BMDMA2 stat 0x82d0009
[ 13.995695] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 13.995696] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 13.995806] ata1.00: status: { DRDY ERR }
[ 13.995854] ata1.00: error: { ABRT }
[ 14.020648] ata1.00: configured for UDMA/100
[ 14.020656] sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
[ 14.020660] sd 0:0:0:0: [sda] Sense Key : Aborted Command [current] [descriptor]
[ 14.020665] Descriptor sense data with sense descriptors (in hex):
[ 14.020667] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 14.020677] 00 00 00 00
[ 14.020681] sd 0:0:0:0: [sda] Add. Sense: No additional sense information
[ 14.020686] end_request: I/O error, dev sda, sector 0
[ 14.020736] Buffer I/O error on device sda, logical block 0
[ 14.020790] ata1: EH complete
[ 14.167741] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 14.167792] ata1.00: BMDMA2 stat 0x82d0009
[ 14.167844] ata1.00: cmd c8/00:08:18:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 14.167845] res 51/04:08:18:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 14.167955] ata1.00: status: { DRDY ERR }
[ 14.168008] ata1.00: error: { ABRT }
[ 14.192648] ata1.00: configured for UDMA/100
[ 14.192657] ata1: EH complete
[ 14.339583] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 14.339634] ata1.00: BMDMA2 stat 0x82d0009
[ 14.339685] ata1.00: cmd c8/00:08:18:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 14.339686] res 51/04:08:18:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 14.340324] ata1.00: status: { DRDY ERR }
[ 14.340373] ata1.00: error: { ABRT }
[ 14.364648] ata1.00: configured for UDMA/100
[ 14.364657] ata1: EH complete
[ 14.511634] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 14.511685] ata1.00: BMDMA2 stat 0x82d0009
[ 14.511736] ata1.00: cmd c8/00:08:18:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 14.511738] res 51/04:08:18:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 14.511848] ata1.00: status: { DRDY ERR }
[ 14.511896] ata1.00: error: { ABRT }
[ 14.536648] ata1.00: configured for UDMA/100
[ 14.536657] ata1: EH complete
[ 14.683585] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 14.683636] ata1.00: BMDMA2 stat 0x82d0009
[ 14.683687] ata1.00: cmd c8/00:08:18:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 14.683689] res 51/04:08:18:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 14.683799] ata1.00: status: { DRDY ERR }
[ 14.683847] ata1.00: error: { ABRT }
[ 14.708648] ata1.00: configured for UDMA/100
[ 14.708657] ata1: EH complete
[ 14.855634] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 14.855685] ata1.00: BMDMA2 stat 0x82d0009
[ 14.855736] ata1.00: cmd c8/00:08:18:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 14.855738] res 51/04:08:18:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 14.855848] ata1.00: status: { DRDY ERR }
[ 14.855896] ata1.00: error: { ABRT }
[ 14.880648] ata1.00: configured for UDMA/100
[ 14.880657] ata1: EH complete
[ 15.027581] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 15.027632] ata1.00: BMDMA2 stat 0x82d0009
[ 15.027683] ata1.00: cmd c8/00:08:18:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 15.027685] res 51/04:08:18:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 15.027795] ata1.00: status: { DRDY ERR }
[ 15.027843] ata1.00: error: { ABRT }
[ 15.052647] ata1.00: configured for UDMA/100
[ 15.052656] sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
[ 15.052660] sd 0:0:0:0: [sda] Sense Key : Aborted Command [current] [descriptor]
[ 15.052665] Descriptor sense data with sense descriptors (in hex):
[ 15.052668] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 15.052677] 00 00 00 18
[ 15.052682] sd 0:0:0:0: [sda] Add. Sense: No additional sense information
[ 15.052687] end_request: I/O error, dev sda, sector 24
[ 15.052737] Buffer I/O error on device sda, logical block 3
[ 15.052791] ata1: EH complete
[ 15.199738] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 15.199788] ata1.00: BMDMA2 stat 0x82d0009
[ 15.199840] ata1.00: cmd c8/00:08:18:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 15.199841] res 51/04:08:18:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 15.199951] ata1.00: status: { DRDY ERR }
[ 15.199999] ata1.00: error: { ABRT }
[ 15.224647] ata1.00: configured for UDMA/100
[ 15.224656] ata1: EH complete
[ 15.371580] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 15.371631] ata1.00: BMDMA2 stat 0x82d0009
[ 15.371682] ata1.00: cmd c8/00:08:18:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 15.371684] res 51/04:08:18:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 15.371794] ata1.00: status: { DRDY ERR }
[ 15.371842] ata1.00: error: { ABRT }
[ 15.396645] ata1.00: configured for UDMA/100
[ 15.396654] ata1: EH complete
[ 15.543632] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 15.543682] ata1.00: BMDMA2 stat 0x82d0009
[ 15.543734] ata1.00: cmd c8/00:08:18:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 15.543735] res 51/04:08:18:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 15.543845] ata1.00: status: { DRDY ERR }
[ 15.543893] ata1.00: error: { ABRT }
[ 15.568645] ata1.00: configured for UDMA/100
[ 15.568654] ata1: EH complete
[ 15.715579] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 15.715629] ata1.00: BMDMA2 stat 0x82d0009
[ 15.715681] ata1.00: cmd c8/00:08:18:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 15.715682] res 51/04:08:18:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 15.715793] ata1.00: status: { DRDY ERR }
[ 15.715840] ata1.00: error: { ABRT }
[ 15.740648] ata1.00: configured for UDMA/100
[ 15.740657] ata1: EH complete
[ 15.887631] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 15.887681] ata1.00: BMDMA2 stat 0x82d0009
[ 15.887732] ata1.00: cmd c8/00:08:18:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 15.887734] res 51/04:08:18:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 15.887844] ata1.00: status: { DRDY ERR }
[ 15.887892] ata1.00: error: { ABRT }
[ 15.912650] ata1.00: configured for UDMA/100
[ 15.912659] ata1: EH complete
[ 16.059578] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 16.059629] ata1.00: BMDMA2 stat 0x82d0009
[ 16.059680] ata1.00: cmd c8/00:08:18:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 16.059681] res 51/04:08:18:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 16.059791] ata1.00: status: { DRDY ERR }
[ 16.059839] ata1.00: error: { ABRT }
[ 16.084648] ata1.00: configured for UDMA/100
[ 16.084656] sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
[ 16.084660] sd 0:0:0:0: [sda] Sense Key : Aborted Command [current] [descriptor]
[ 16.084665] Descriptor sense data with sense descriptors (in hex):
[ 16.084667] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 16.084677] 00 00 00 18
[ 16.084681] sd 0:0:0:0: [sda] Add. Sense: No additional sense information
[ 16.084686] end_request: I/O error, dev sda, sector 24
[ 16.084736] Buffer I/O error on device sda, logical block 3
[ 16.084790] ata1: EH complete
[ 16.231731] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 16.231781] ata1.00: BMDMA2 stat 0x82d0009
[ 16.231832] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 16.231834] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 16.231944] ata1.00: status: { DRDY ERR }
[ 16.231992] ata1.00: error: { ABRT }
[ 16.256648] ata1.00: configured for UDMA/100
[ 16.256657] ata1: EH complete
[ 16.403576] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 16.403627] ata1.00: BMDMA2 stat 0x82d0009
[ 16.403678] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 16.403680] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 16.403790] ata1.00: status: { DRDY ERR }
[ 16.403838] ata1.00: error: { ABRT }
[ 16.428647] ata1.00: configured for UDMA/100
[ 16.428656] ata1: EH complete
[ 16.575628] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 16.575679] ata1.00: BMDMA2 stat 0x82d0009
[ 16.575730] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 16.575732] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 16.575842] ata1.00: status: { DRDY ERR }
[ 16.575890] ata1.00: error: { ABRT }
[ 16.600647] ata1.00: configured for UDMA/100
[ 16.600656] ata1: EH complete
[ 16.747575] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 16.747626] ata1.00: BMDMA2 stat 0x82d0009
[ 16.747677] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 16.747679] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 16.747789] ata1.00: status: { DRDY ERR }
[ 16.747837] ata1.00: error: { ABRT }
[ 16.772651] ata1.00: configured for UDMA/100
[ 16.772661] ata1: EH complete
[ 16.919628] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 16.919679] ata1.00: BMDMA2 stat 0x82d0009
[ 16.919730] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 16.919732] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 16.919842] ata1.00: status: { DRDY ERR }
[ 16.919890] ata1.00: error: { ABRT }
[ 16.944647] ata1.00: configured for UDMA/100
[ 16.944656] ata1: EH complete
[ 17.091575] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 17.091626] ata1.00: BMDMA2 stat 0x82d0009
[ 17.091677] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 17.091678] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 17.091788] ata1.00: status: { DRDY ERR }
[ 17.091836] ata1.00: error: { ABRT }
[ 17.116648] ata1.00: configured for UDMA/100
[ 17.116656] sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
[ 17.116660] sd 0:0:0:0: [sda] Sense Key : Aborted Command [current] [descriptor]
[ 17.116665] Descriptor sense data with sense descriptors (in hex):
[ 17.116668] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 17.116678] 00 00 00 00
[ 17.116682] sd 0:0:0:0: [sda] Add. Sense: No additional sense information
[ 17.116687] end_request: I/O error, dev sda, sector 0
[ 17.116737] Buffer I/O error on device sda, logical block 0
[ 17.116791] ata1: EH complete
[ 17.263730] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 17.263781] ata1.00: BMDMA2 stat 0x82d0009
[ 17.263832] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 17.263834] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 17.263944] ata1.00: status: { DRDY ERR }
[ 17.263992] ata1.00: error: { ABRT }
[ 17.288648] ata1.00: configured for UDMA/100
[ 17.288657] ata1: EH complete
[ 17.435571] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 17.435622] ata1.00: BMDMA2 stat 0x82d0009
[ 17.435673] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 17.435674] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 17.435784] ata1.00: status: { DRDY ERR }
[ 17.435832] ata1.00: error: { ABRT }
[ 17.456647] ata1.00: configured for UDMA/100
[ 17.456656] ata1: EH complete
[ 17.603560] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 17.603611] ata1.00: BMDMA2 stat 0x82d0009
[ 17.603662] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 17.603664] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 17.603774] ata1.00: status: { DRDY ERR }
[ 17.603822] ata1.00: error: { ABRT }
[ 17.624648] ata1.00: configured for UDMA/100
[ 17.624657] ata1: EH complete
[ 17.771550] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 17.771600] ata1.00: BMDMA2 stat 0x82d0009
[ 17.771651] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 17.771653] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 17.771763] ata1.00: status: { DRDY ERR }
[ 17.771811] ata1.00: error: { ABRT }
[ 17.792648] ata1.00: configured for UDMA/100
[ 17.792657] ata1: EH complete
[ 17.939647] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 17.939698] ata1.00: BMDMA2 stat 0x82d0009
[ 17.939749] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 17.939751] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 17.939861] ata1.00: status: { DRDY ERR }
[ 17.939908] ata1.00: error: { ABRT }
[ 17.964647] ata1.00: configured for UDMA/100
[ 17.964656] ata1: EH complete
[ 18.111594] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 18.111645] ata1.00: BMDMA2 stat 0x82d0009
[ 18.111696] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 18.111698] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 18.112338] ata1.00: status: { DRDY ERR }
[ 18.112386] ata1.00: error: { ABRT }
[ 18.136647] ata1.00: configured for UDMA/100
[ 18.136656] sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
[ 18.136660] sd 0:0:0:0: [sda] Sense Key : Aborted Command [current] [descriptor]
[ 18.136664] Descriptor sense data with sense descriptors (in hex):
[ 18.136667] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 18.136677] 00 00 00 00
[ 18.136681] sd 0:0:0:0: [sda] Add. Sense: No additional sense information
[ 18.136686] end_request: I/O error, dev sda, sector 0
[ 18.136736] Buffer I/O error on device sda, logical block 0
[ 18.136790] ata1: EH complete
[ 18.136795] unable to read partition table
[ 18.136884] sd 0:0:0:0: [sda] Attached SCSI disk
[ 18.136944] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 18.137144] pata_atiixp 0000:00:14.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 18.137204] pata_atiixp 0000:00:14.1: setting latency timer to 64
[ 18.137304] scsi2 : pata_atiixp
[ 18.137370] scsi3 : pata_atiixp
[ 18.138733] ata3: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x8460 irq 14
[ 18.138737] ata4: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x8468 irq 15
[ 18.138782] ata3: port disabled. ignoring.
[ 18.316573] ata4.00: ATAPI: TSSTcorpCDW/DVD TS-L462C, TO11, max UDMA/33
[ 18.348566] ata4.00: configured for UDMA/33
[ 18.349493] scsi 3:0:0:0: CD-ROM TSSTcorp CDW/DVD TS-L462C TO11 PQ: 0 ANSI: 5
[ 18.350478] sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
[ 18.350482] Uniform CD-ROM driver Revision: 3.20
[ 18.350597] sr 3:0:0:0: Attached scsi CD-ROM sr0
[ 18.350650] sr 3:0:0:0: Attached scsi generic sg1 type 5
[ 18.351122] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 18.351152] ehci_hcd 0000:00:13.2: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 18.351179] ehci_hcd 0000:00:13.2: EHCI Host Controller
[ 18.351255] ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 1
[ 18.351330] ehci_hcd 0000:00:13.2: irq 19, io mem 0xc0506000
[ 18.360018] ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00
[ 18.360127] usb usb1: configuration #1 chosen from 1 choice
[ 18.360160] hub 1-0:1.0: USB hub found
[ 18.360171] hub 1-0:1.0: 8 ports detected
[ 18.360322] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 18.360342] ohci_hcd 0000:00:13.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 18.360357] ohci_hcd 0000:00:13.0: OHCI Host Controller
[ 18.360406] ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 2
[ 18.360425] ohci_hcd 0000:00:13.0: irq 19, io mem 0xc0504000
[ 18.416098] usb usb2: configuration #1 chosen from 1 choice
[ 18.416127] hub 2-0:1.0: USB hub found
[ 18.416143] hub 2-0:1.0: 4 ports detected
[ 18.416244] ohci_hcd 0000:00:13.1: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 18.416258] ohci_hcd 0000:00:13.1: OHCI Host Controller
[ 18.416305] ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 3
[ 18.416327] ohci_hcd 0000:00:13.1: irq 19, io mem 0xc0505000
[ 18.472098] usb usb3: configuration #1 chosen from 1 choice
[ 18.472125] hub 3-0:1.0: USB hub found
[ 18.472141] hub 3-0:1.0: 4 ports detected
[ 18.472248] uhci_hcd: USB Universal Host Controller Interface driver
[ 18.472316] usbcore: registered new interface driver libusual
[ 18.472353] usbcore: registered new interface driver usbserial
[ 18.472366] USB Serial support registered for generic
[ 18.472380] usbcore: registered new interface driver usbserial_generic
[ 18.472383] usbserial: USB Serial Driver core
[ 18.472435] PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12
[ 18.472769] i8042.c: Detected active multiplexing controller, rev 1.1.
[ 18.472857] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 18.472863] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 18.472866] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 18.472869] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 18.472871] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 18.473058] mice: PS/2 mouse device common for all mice
[ 18.473242] rtc_cmos 00:04: RTC can wake from S4
[ 18.473284] rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
[ 18.473318] rtc0: alarms up to one month, 114 bytes nvram
[ 18.473396] device-mapper: uevent: version 1.0.3
[ 18.473534] device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
[ 18.473592] device-mapper: multipath: version 1.0.5 loaded
[ 18.473596] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 18.473688] EISA: Probing bus 0 at eisa.0
[ 18.473701] Cannot allocate resource for EISA slot 1
[ 18.473734] Cannot allocate resource for EISA slot 8
[ 18.473736] EISA: Detected 0 cards.
[ 18.473825] cpuidle: using governor ladder
[ 18.473894] cpuidle: using governor menu
[ 18.474471] TCP cubic registered
[ 18.474595] NET: Registered protocol family 10
[ 18.475049] lo: Disabled Privacy Extensions
[ 18.475389] NET: Registered protocol family 17
[ 18.475410] Bluetooth: L2CAP ver 2.11
[ 18.475412] Bluetooth: L2CAP socket layer initialized
[ 18.475415] Bluetooth: SCO (Voice Link) ver 0.6
[ 18.475417] Bluetooth: SCO socket layer initialized
[ 18.475461] Bluetooth: RFCOMM socket layer initialized
[ 18.475470] Bluetooth: RFCOMM TTY layer initialized
[ 18.475472] Bluetooth: RFCOMM ver 1.10
[ 18.475523] Using IPI No-Shortcut mode
[ 18.475628] registered taskstats version 1
[ 18.475746] Magic number: 9:299:683
[ 18.475860] rtc_cmos 00:04: setting system clock to 2009-05-12 12:40:40 UTC (1242132040)
[ 18.475863] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 18.475866] EDD information not available.
[ 18.476404] Freeing unused kernel memory: 532k freed
[ 18.476534] Write protecting the kernel text: 4128k
[ 18.476578] Write protecting the kernel read-only data: 1532k
[ 18.479849] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4
[ 19.027470] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[ 19.027516] 8139cp 0000:09:06.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip, use 8139too
[ 19.032025] 8139too Fast Ethernet driver 0.9.28
[ 19.032094] 8139too 0000:09:06.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 19.033943] eth0: RealTek RTL8139 at 0xa000, 00:16:d4:1f:87:02, IRQ 22
[ 19.033946] eth0: Identified 8139 chip type 'RTL-8100B/8139D'
[ 19.139875] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 19.139883] ata1.00: BMDMA2 stat 0x82d0009
[ 19.139891] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 19.139893] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 19.139896] ata1.00: status: { DRDY ERR }
[ 19.139899] ata1.00: error: { ABRT }
[ 19.164712] ata1.00: configured for UDMA/100
[ 19.164750] ata1: EH complete
[ 19.281632] Marking TSC unstable due to TSC halts in idle
[ 19.311730] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 19.311736] ata1.00: BMDMA2 stat 0x82d0009
[ 19.311744] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 19.311746] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 19.311750] ata1.00: status: { DRDY ERR }
[ 19.311752] ata1.00: error: { ABRT }
[ 19.332707] ata1.00: configured for UDMA/100
[ 19.332728] ata1: EH complete
[ 19.479711] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 19.479714] ata1.00: BMDMA2 stat 0x82d0009
[ 19.479720] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 19.479722] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 19.479725] ata1.00: status: { DRDY ERR }
[ 19.479728] ata1.00: error: { ABRT }
[ 19.500694] ata1.00: configured for UDMA/100
[ 19.500704] ata1: EH complete
[ 19.647723] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 19.647726] ata1.00: BMDMA2 stat 0x82d0009
[ 19.647732] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 19.647733] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 19.647737] ata1.00: status: { DRDY ERR }
[ 19.647739] ata1.00: error: { ABRT }
[ 19.668700] ata1.00: configured for UDMA/100
[ 19.668710] ata1: EH complete
[ 19.815738] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 19.815741] ata1.00: BMDMA2 stat 0x82d0009
[ 19.815747] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 19.815749] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 19.815752] ata1.00: status: { DRDY ERR }
[ 19.815754] ata1.00: error: { ABRT }
[ 19.836702] ata1.00: configured for UDMA/100
[ 19.836711] ata1: EH complete
[ 19.983668] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 19.983674] ata1.00: BMDMA2 stat 0x82d0009
[ 19.983682] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 19.983684] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 19.983687] ata1.00: status: { DRDY ERR }
[ 19.983690] ata1.00: error: { ABRT }
[ 20.004748] ata1.00: configured for UDMA/100
[ 20.004766] sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
[ 20.004771] sd 0:0:0:0: [sda] Sense Key : Aborted Command [current] [descriptor]
[ 20.004777] Descriptor sense data with sense descriptors (in hex):
[ 20.004780] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 20.004790] 00 00 00 00
[ 20.004794] sd 0:0:0:0: [sda] Add. Sense: No additional sense information
[ 20.004800] end_request: I/O error, dev sda, sector 0
[ 20.004805] Buffer I/O error on device sda, logical block 0
[ 20.004821] ata1: EH complete
[ 20.151870] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 20.151873] ata1.00: BMDMA2 stat 0x82d0009
[ 20.151879] ata1.00: cmd c8/00:18:08:00:00/00:00:00:00:00/e0 tag 0 dma 12288 in
[ 20.151881] res 51/04:18:08:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 20.151884] ata1.00: status: { DRDY ERR }
[ 20.151887] ata1.00: error: { ABRT }
[ 20.176704] ata1.00: configured for UDMA/100
[ 20.176714] ata1: EH complete
[ 20.323732] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 20.323735] ata1.00: BMDMA2 stat 0x82d0009
[ 20.323741] ata1.00: cmd c8/00:18:08:00:00/00:00:00:00:00/e0 tag 0 dma 12288 in
[ 20.323742] res 51/04:18:08:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 20.323746] ata1.00: status: { DRDY ERR }
[ 20.323748] ata1.00: error: { ABRT }
[ 20.344702] ata1.00: configured for UDMA/100
[ 20.344712] ata1: EH complete
[ 20.491752] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 20.491757] ata1.00: BMDMA2 stat 0x82d0009
[ 20.491764] ata1.00: cmd c8/00:18:08:00:00/00:00:00:00:00/e0 tag 0 dma 12288 in
[ 20.491766] res 51/04:18:08:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 20.491769] ata1.00: status: { DRDY ERR }
[ 20.491772] ata1.00: error: { ABRT }
[ 20.512738] ata1.00: configured for UDMA/100
[ 20.512751] ata1: EH complete
[ 20.659766] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 20.659770] ata1.00: BMDMA2 stat 0x82d0009
[ 20.659776] ata1.00: cmd c8/00:18:08:00:00/00:00:00:00:00/e0 tag 0 dma 12288 in
[ 20.659778] res 51/04:18:08:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 20.659781] ata1.00: status: { DRDY ERR }
[ 20.659784] ata1.00: error: { ABRT }
[ 20.680702] ata1.00: configured for UDMA/100
[ 20.680715] ata1: EH complete
[ 20.827685] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 20.827691] ata1.00: BMDMA2 stat 0x82d0009
[ 20.827699] ata1.00: cmd c8/00:18:08:00:00/00:00:00:00:00/e0 tag 0 dma 12288 in
[ 20.827700] res 51/04:18:08:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 20.827704] ata1.00: status: { DRDY ERR }
[ 20.827706] ata1.00: error: { ABRT }
[ 20.848699] ata1.00: configured for UDMA/100
[ 20.848715] ata1: EH complete
[ 20.995674] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 20.995677] ata1.00: BMDMA2 stat 0x82d0009
[ 20.995683] ata1.00: cmd c8/00:18:08:00:00/00:00:00:00:00/e0 tag 0 dma 12288 in
[ 20.995685] res 51/04:18:08:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 20.995689] ata1.00: status: { DRDY ERR }
[ 20.995691] ata1.00: error: { ABRT }
[ 21.020704] ata1.00: configured for UDMA/100
[ 21.020720] sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
[ 21.020725] sd 0:0:0:0: [sda] Sense Key : Aborted Command [current] [descriptor]
[ 21.020731] Descriptor sense data with sense descriptors (in hex):
[ 21.020734] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 21.020744] 00 00 00 08
[ 21.020748] sd 0:0:0:0: [sda] Add. Sense: No additional sense information
[ 21.020753] end_request: I/O error, dev sda, sector 8
[ 21.020758] Buffer I/O error on device sda, logical block 1
[ 21.020763] Buffer I/O error on device sda, logical block 2
[ 21.020766] Buffer I/O error on device sda, logical block 3
[ 21.020776] ata1: EH complete
[ 21.020867] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors: (100 GB/93.1 GiB)
[ 21.167751] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 21.167754] ata1.00: BMDMA2 stat 0x82d0009
[ 21.167761] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 21.167762] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 21.167766] ata1.00: status: { DRDY ERR }
[ 21.167768] ata1.00: error: { ABRT }
[ 21.188703] ata1.00: configured for UDMA/100
[ 21.188713] ata1: EH complete
[ 21.335658] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 21.335662] ata1.00: BMDMA2 stat 0x82d0009
[ 21.335667] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 21.335669] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 21.335672] ata1.00: status: { DRDY ERR }
[ 21.335675] ata1.00: error: { ABRT }
[ 21.356700] ata1.00: configured for UDMA/100
[ 21.356710] ata1: EH complete
[ 21.503672] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 21.503675] ata1.00: BMDMA2 stat 0x82d0009
[ 21.503681] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 21.503683] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 21.503686] ata1.00: status: { DRDY ERR }
[ 21.503688] ata1.00: error: { ABRT }
[ 21.524691] ata1.00: configured for UDMA/100
[ 21.524701] ata1: EH complete
[ 21.671682] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 21.671685] ata1.00: BMDMA2 stat 0x82d0009
[ 21.671691] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 21.671692] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 21.671696] ata1.00: status: { DRDY ERR }
[ 21.671698] ata1.00: error: { ABRT }
[ 21.692706] ata1.00: configured for UDMA/100
[ 21.692716] ata1: EH complete
[ 21.839694] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 21.839697] ata1.00: BMDMA2 stat 0x82d0009
[ 21.839702] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 21.839704] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 21.839707] ata1.00: status: { DRDY ERR }
[ 21.839710] ata1.00: error: { ABRT }
[ 21.860702] ata1.00: configured for UDMA/100
[ 21.860712] ata1: EH complete
[ 22.007703] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 22.007706] ata1.00: BMDMA2 stat 0x82d0009
[ 22.007712] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 22.007713] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 22.007717] ata1.00: status: { DRDY ERR }
[ 22.007719] ata1.00: error: { ABRT }
[ 22.028701] ata1.00: configured for UDMA/100
[ 22.028711] sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
[ 22.028714] sd 0:0:0:0: [sda] Sense Key : Aborted Command [current] [descriptor]
[ 22.028719] Descriptor sense data with sense descriptors (in hex):
[ 22.028722] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 22.028732] 00 00 00 00
[ 22.028736] sd 0:0:0:0: [sda] Add. Sense: No additional sense information
[ 22.028741] end_request: I/O error, dev sda, sector 0
[ 22.028744] Buffer I/O error on device sda, logical block 0
[ 22.028755] ata1: EH complete
[ 22.029887] sd 0:0:0:0: [sda] Write Protect is off
[ 22.029891] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 22.029939] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 22.029978] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors: (100 GB/93.1 GiB)
[ 22.029995] sd 0:0:0:0: [sda] Write Protect is off
[ 22.029998] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 22.030026] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 22.132067] hub 2-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
[ 22.569560] ISO 9660 Extensions: Microsoft Joliet Level 3
[ 22.644419] ISO 9660 Extensions: RRIP_1991A
[ 23.028612] aufs 20080922
[ 23.336428] squashfs: version 3.3 (2007/10/31) Phillip Lougher
[ 25.420071] hub 2-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
[ 28.708047] hub 2-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
[ 31.996062] hub 2-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
[ 31.996076] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 32.300072] usb 2-3: new low speed USB device using ohci_hcd and address 6
[ 32.502954] usb 2-3: configuration #1 chosen from 1 choice
[ 32.511229] usbcore: registered new interface driver hiddev
[ 32.515364] input: HID 04b3:310b as /devices/pci0000:00/0000:00:13.0/usb2/2-3/2-3:1.0/input/input5
[ 32.515679] generic-usb 0003:04B3:310B.0001: input,hidraw0: USB HID v1.00 Mouse [HID 04b3:310b] on usb-0000:00:13.0-3/input0
[ 32.515702] usbcore: registered new interface driver usbhid
[ 32.515706] usbhid: v2.6:USB HID core driver
[ 77.174831] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 77.174838] ata1.00: BMDMA2 stat 0x82d0009
[ 77.174847] ata1.00: cmd c8/00:20:00:00:00/00:00:00:00:00/e0 tag 0 dma 16384 in
[ 77.174849] res 51/04:20:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 77.174852] ata1.00: status: { DRDY ERR }
[ 77.174855] ata1.00: error: { ABRT }
[ 77.196758] ata1.00: configured for UDMA/100
[ 77.196795] ata1: EH complete
[ 77.343780] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 77.343787] ata1.00: BMDMA2 stat 0x82d0009
[ 77.343795] ata1.00: cmd c8/00:20:00:00:00/00:00:00:00:00/e0 tag 0 dma 16384 in
[ 77.343797] res 51/04:20:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 77.343801] ata1.00: status: { DRDY ERR }
[ 77.343803] ata1.00: error: { ABRT }
[ 77.364692] ata1.00: configured for UDMA/100
[ 77.364709] ata1: EH complete
[ 77.511664] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 77.511667] ata1.00: BMDMA2 stat 0x82d0009
[ 77.511673] ata1.00: cmd c8/00:20:00:00:00/00:00:00:00:00/e0 tag 0 dma 16384 in
[ 77.511675] res 51/04:20:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 77.511678] ata1.00: status: { DRDY ERR }
[ 77.511681] ata1.00: error: { ABRT }
[ 77.532705] ata1.00: configured for UDMA/100
[ 77.532715] ata1: EH complete
[ 77.679692] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 77.679697] ata1.00: BMDMA2 stat 0x82d0009
[ 77.679703] ata1.00: cmd c8/00:20:00:00:00/00:00:00:00:00/e0 tag 0 dma 16384 in
[ 77.679705] res 51/04:20:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 77.679709] ata1.00: status: { DRDY ERR }
[ 77.679711] ata1.00: error: { ABRT }
[ 77.700697] ata1.00: configured for UDMA/100
[ 77.700711] ata1: EH complete
[ 77.847693] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 77.847696] ata1.00: BMDMA2 stat 0x82d0009
[ 77.847702] ata1.00: cmd c8/00:20:00:00:00/00:00:00:00:00/e0 tag 0 dma 16384 in
[ 77.847704] res 51/04:20:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 77.847708] ata1.00: status: { DRDY ERR }
[ 77.847710] ata1.00: error: { ABRT }
[ 77.868707] ata1.00: configured for UDMA/100
[ 77.868719] ata1: EH complete
[ 78.015709] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 78.015713] ata1.00: BMDMA2 stat 0x82d0009
[ 78.015721] ata1.00: cmd c8/00:20:00:00:00/00:00:00:00:00/e0 tag 0 dma 16384 in
[ 78.015723] res 51/04:20:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 78.015726] ata1.00: status: { DRDY ERR }
[ 78.015729] ata1.00: error: { ABRT }
[ 78.036702] ata1.00: configured for UDMA/100
[ 78.036718] sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
[ 78.036723] sd 0:0:0:0: [sda] Sense Key : Aborted Command [current] [descriptor]
[ 78.036729] Descriptor sense data with sense descriptors (in hex):
[ 78.036731] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 78.036741] 00 00 00 00
[ 78.036746] sd 0:0:0:0: [sda] Add. Sense: No additional sense information
[ 78.036751] end_request: I/O error, dev sda, sector 0
[ 78.036756] Buffer I/O error on device sda, logical block 0
[ 78.036762] Buffer I/O error on device sda, logical block 1
[ 78.036765] Buffer I/O error on device sda, logical block 2
[ 78.036768] Buffer I/O error on device sda, logical block 3
[ 78.036777] ata1: EH complete
[ 78.183821] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 78.183824] ata1.00: BMDMA2 stat 0x82d0009
[ 78.183830] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 78.183832] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 78.183835] ata1.00: status: { DRDY ERR }
[ 78.183838] ata1.00: error: { ABRT }
[ 78.204708] ata1.00: configured for UDMA/100
[ 78.204720] ata1: EH complete
[ 78.351726] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 78.351729] ata1.00: BMDMA2 stat 0x82d0009
[ 78.351735] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 78.351737] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 78.351741] ata1.00: status: { DRDY ERR }
[ 78.351743] ata1.00: error: { ABRT }
[ 78.372705] ata1.00: configured for UDMA/100
[ 78.372716] ata1: EH complete
[ 78.519737] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 78.519740] ata1.00: BMDMA2 stat 0x82d0009
[ 78.519746] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 78.519748] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 78.519751] ata1.00: status: { DRDY ERR }
[ 78.519753] ata1.00: error: { ABRT }
[ 78.540702] ata1.00: configured for UDMA/100
[ 78.540712] ata1: EH complete
[ 78.687645] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 78.687648] ata1.00: BMDMA2 stat 0x82d0009
[ 78.687654] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 78.687656] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 78.687659] ata1.00: status: { DRDY ERR }
[ 78.687661] ata1.00: error: { ABRT }
[ 78.708692] ata1.00: configured for UDMA/100
[ 78.708702] ata1: EH complete
[ 78.855658] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 78.855661] ata1.00: BMDMA2 stat 0x82d0009
[ 78.855666] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 78.855668] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 78.855671] ata1.00: status: { DRDY ERR }
[ 78.855674] ata1.00: error: { ABRT }
[ 78.876700] ata1.00: configured for UDMA/100
[ 78.876710] ata1: EH complete
[ 79.023670] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 79.023673] ata1.00: BMDMA2 stat 0x82d0009
[ 79.023678] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 79.023680] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 79.023683] ata1.00: status: { DRDY ERR }
[ 79.023686] ata1.00: error: { ABRT }
[ 79.044696] ata1.00: configured for UDMA/100
[ 79.044705] sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
[ 79.044709] sd 0:0:0:0: [sda] Sense Key : Aborted Command [current] [descriptor]
[ 79.044714] Descriptor sense data with sense descriptors (in hex):
[ 79.044717] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 79.044727] 00 00 00 00
[ 79.044731] sd 0:0:0:0: [sda] Add. Sense: No additional sense information
[ 79.044736] end_request: I/O error, dev sda, sector 0
[ 79.044740] Buffer I/O error on device sda, logical block 0
[ 79.044752] ata1: EH complete
[ 79.045906] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors: (100 GB/93.1 GiB)
[ 79.045948] sd 0:0:0:0: [sda] Write Protect is off
[ 79.045951] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 79.045983] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 79.046019] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors: (100 GB/93.1 GiB)
[ 79.046036] sd 0:0:0:0: [sda] Write Protect is off
[ 79.046039] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 79.046067] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 97.792566] udev: starting version 141
[ 98.552655] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 98.552662] ata1.00: BMDMA2 stat 0x82d0009
[ 98.552670] ata1.00: cmd c8/00:20:00:00:00/00:00:00:00:00/e0 tag 0 dma 16384 in
[ 98.552672] res 51/04:20:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 98.552676] ata1.00: status: { DRDY ERR }
[ 98.552678] ata1.00: error: { ABRT }
[ 98.576705] ata1.00: configured for UDMA/100
[ 98.576728] ata1: EH complete
[ 98.723683] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 98.723689] ata1.00: BMDMA2 stat 0x82d0009
[ 98.723696] ata1.00: cmd c8/00:20:00:00:00/00:00:00:00:00/e0 tag 0 dma 16384 in
[ 98.723698] res 51/04:20:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 98.723702] ata1.00: status: { DRDY ERR }
[ 98.723704] ata1.00: error: { ABRT }
[ 98.744695] ata1.00: configured for UDMA/100
[ 98.744706] ata1: EH complete
[ 98.891691] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 98.891695] ata1.00: BMDMA2 stat 0x82d0009
[ 98.891701] ata1.00: cmd c8/00:20:00:00:00/00:00:00:00:00/e0 tag 0 dma 16384 in
[ 98.891703] res 51/04:20:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 98.891707] ata1.00: status: { DRDY ERR }
[ 98.891709] ata1.00: error: { ABRT }
[ 98.912702] ata1.00: configured for UDMA/100
[ 98.912714] ata1: EH complete
[ 99.059701] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 99.059704] ata1.00: BMDMA2 stat 0x82d0009
[ 99.059710] ata1.00: cmd c8/00:20:00:00:00/00:00:00:00:00/e0 tag 0 dma 16384 in
[ 99.059712] res 51/04:20:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 99.059715] ata1.00: status: { DRDY ERR }
[ 99.059718] ata1.00: error: { ABRT }
[ 99.080700] ata1.00: configured for UDMA/100
[ 99.080710] ata1: EH complete
[ 99.180048] cfg80211: Calling CRDA to update world regulatory domain
[ 99.227735] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 99.227741] ata1.00: BMDMA2 stat 0x82d0009
[ 99.227749] ata1.00: cmd c8/00:20:00:00:00/00:00:00:00:00/e0 tag 0 dma 16384 in
[ 99.227751] res 51/04:20:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 99.227755] ata1.00: status: { DRDY ERR }
[ 99.227757] ata1.00: error: { ABRT }
[ 99.248761] ata1.00: configured for UDMA/100
[ 99.248777] ata1: EH complete
[ 99.395744] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 99.395751] ata1.00: BMDMA2 stat 0x82d0009
[ 99.395759] ata1.00: cmd c8/00:20:00:00:00/00:00:00:00:00/e0 tag 0 dma 16384 in
[ 99.395761] res 51/04:20:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 99.395765] ata1.00: status: { DRDY ERR }
[ 99.395767] ata1.00: error: { ABRT }
[ 99.416703] ata1.00: configured for UDMA/100
[ 99.416724] sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
[ 99.416730] sd 0:0:0:0: [sda] Sense Key : Aborted Command [current] [descriptor]
[ 99.416736] Descriptor sense data with sense descriptors (in hex):
[ 99.416738] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 99.416749] 00 00 00 00
[ 99.416753] sd 0:0:0:0: [sda] Add. Sense: No additional sense information
[ 99.416758] end_request: I/O error, dev sda, sector 0
[ 99.416764] Buffer I/O error on device sda, logical block 0
[ 99.416770] Buffer I/O error on device sda, logical block 1
[ 99.416774] Buffer I/O error on device sda, logical block 2
[ 99.416777] Buffer I/O error on device sda, logical block 3
[ 99.416795] ata1: EH complete
[ 99.563850] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 99.563856] ata1.00: BMDMA2 stat 0x82d0009
[ 99.563862] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 99.563864] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 99.563868] ata1.00: status: { DRDY ERR }
[ 99.563870] ata1.00: error: { ABRT }
[ 99.584701] ata1.00: configured for UDMA/100
[ 99.584715] ata1: EH complete
[ 99.690383] input: PC Speaker as /devices/platform/pcspkr/input/input6
[ 99.731770] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 99.731777] ata1.00: BMDMA2 stat 0x82d0009
[ 99.731785] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 99.731787] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 99.731791] ata1.00: status: { DRDY ERR }
[ 99.731793] ata1.00: error: { ABRT }
[ 99.746773] piix4_smbus 0000:00:14.0: SMBus Host Controller at 0x8450, revision 0
[ 99.757044] ata1.00: configured for UDMA/100
[ 99.757075] ata1: EH complete
[ 99.904053] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 99.904059] ata1.00: BMDMA2 stat 0x82d0009
[ 99.904067] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 99.904069] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 99.904073] ata1.00: status: { DRDY ERR }
[ 99.904075] ata1.00: error: { ABRT }
[ 99.928779] ata1.00: configured for UDMA/100
[ 99.928813] ata1: EH complete
[ 99.983838] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 100.073971] Linux agpgart interface v0.103
[ 100.076067] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 100.076074] ata1.00: BMDMA2 stat 0x82d0009
[ 100.076082] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 100.076084] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 100.076088] ata1.00: status: { DRDY ERR }
[ 100.076090] ata1.00: error: { ABRT }
[ 100.100740] ata1.00: configured for UDMA/100
[ 100.100773] ata1: EH complete
[ 100.247782] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 100.247789] ata1.00: BMDMA2 stat 0x82d0009
[ 100.247797] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 100.247799] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 100.247802] ata1.00: status: { DRDY ERR }
[ 100.247805] ata1.00: error: { ABRT }
[ 100.268734] ata1.00: configured for UDMA/100
[ 100.268750] ata1: EH complete
[ 100.415788] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 100.415793] ata1.00: BMDMA2 stat 0x82d0009
[ 100.415800] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 100.415801] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 100.415805] ata1.00: status: { DRDY ERR }
[ 100.415807] ata1.00: error: { ABRT }
[ 100.436707] ata1.00: configured for UDMA/100
[ 100.436723] sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
[ 100.436729] sd 0:0:0:0: [sda] Sense Key : Aborted Command [current] [descriptor]
[ 100.436735] Descriptor sense data with sense descriptors (in hex):
[ 100.436738] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 100.436748] 00 00 00 00
[ 100.436752] sd 0:0:0:0: [sda] Add. Sense: No additional sense information
[ 100.436757] end_request: I/O error, dev sda, sector 0
[ 100.436762] Buffer I/O error on device sda, logical block 0
[ 100.436775] ata1: EH complete
[ 100.437352] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors: (100 GB/93.1 GiB)
[ 100.437388] sd 0:0:0:0: [sda] Write Protect is off
[ 100.437391] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 100.437422] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 100.437461] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors: (100 GB/93.1 GiB)
[ 100.437478] sd 0:0:0:0: [sda] Write Protect is off
[ 100.437481] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 100.437509] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 100.846183] synaptics was reset on resume, see synaptics_resume_reset if you have trouble on resume
[ 100.977629] acpi device:21: registered as cooling_device1
[ 100.977982] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A03:00/device:1e/device:1f/input/input7
[ 100.980644] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
[ 101.259947] cfg80211: World regulatory domain updated:
[ 101.259955] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 101.259959] (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 101.259962] (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 101.259965] (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 101.259968] (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 101.259971] (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 101.273505] yenta_cardbus 0000:09:04.0: CardBus bridge found [1179:ff00]
[ 101.273545] yenta_cardbus 0000:09:04.0: Using CSCINT to route CSC interrupts to PCI
[ 101.273548] yenta_cardbus 0000:09:04.0: Routing CardBus interrupts to PCI
[ 101.273557] yenta_cardbus 0000:09:04.0: TI: mfunc 0x00111c12, devctl 0x44
[ 101.467142] input: PS/2 Mouse as /devices/platform/i8042/serio4/input/input8
[ 101.495984] input: AlpsPS/2 ALPS GlidePoint as /devices/platform/i8042/serio4/input/input9
[ 101.508803] yenta_cardbus 0000:09:04.0: ISA IRQ mask 0x0ef8, PCI irq 17
[ 101.508813] yenta_cardbus 0000:09:04.0: Socket status: 30000006
[ 101.508822] yenta_cardbus 0000:09:04.0: pcmcia: parent PCI bridge I/O window: 0xa000 - 0xafff
[ 101.508826] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa000-0xafff: clean.
[ 101.509155] yenta_cardbus 0000:09:04.0: pcmcia: parent PCI bridge Memory window: 0xc0200000 - 0xc02fffff
[ 101.509205] yenta_cardbus 0000:09:04.0: pcmcia: parent PCI bridge Memory window: 0x40000000 - 0x43ffffff
[ 101.513051] ath5k_pci 0000:02:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 101.513064] ath5k_pci 0000:02:00.0: setting latency timer to 64
[ 101.513210] ath5k_pci 0000:02:00.0: registered as 'phy0'
[ 101.606388] phy0: Selected rate control algorithm 'pid'
[ 101.743361] ath5k phy0: Atheros AR5414 chip found (MAC: 0xa0, PHY: 0x61)
[ 101.928514] HDA Intel 0000:00:14.2: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 102.124760] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3af: clean.
[ 102.127245] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3e0-0x4ff: clean.
[ 102.128312] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x820-0x8ff: clean.
[ 102.129172] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcf7: clean.
[ 102.130102] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff: clean.
[ 113.141895] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 113.141902] ata1.00: BMDMA2 stat 0x82d0009
[ 113.141910] ata1.00: cmd c8/00:20:00:00:00/00:00:00:00:00/e0 tag 0 dma 16384 in
[ 113.141912] res 51/04:20:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 113.141916] ata1.00: status: { DRDY ERR }
[ 113.141919] ata1.00: error: { ABRT }
[ 113.167939] ata1.00: configured for UDMA/100
[ 113.167969] ata1: EH complete
[ 113.315016] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 113.315023] ata1.00: BMDMA2 stat 0x82d0009
[ 113.315031] ata1.00: cmd c8/00:20:00:00:00/00:00:00:00:00/e0 tag 0 dma 16384 in
[ 113.315033] res 51/04:20:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 113.315037] ata1.00: status: { DRDY ERR }
[ 113.315039] ata1.00: error: { ABRT }
[ 113.336703] ata1.00: configured for UDMA/100
[ 113.336725] ata1: EH complete
[ 113.483736] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 113.483739] ata1.00: BMDMA2 stat 0x82d0009
[ 113.483745] ata1.00: cmd c8/00:20:00:00:00/00:00:00:00:00/e0 tag 0 dma 16384 in
[ 113.483747] res 51/04:20:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 113.483751] ata1.00: status: { DRDY ERR }
[ 113.483753] ata1.00: error: { ABRT }
[ 113.504701] ata1.00: configured for UDMA/100
[ 113.504714] ata1: EH complete
[ 113.651747] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 113.651751] ata1.00: BMDMA2 stat 0x82d0009
[ 113.651757] ata1.00: cmd c8/00:20:00:00:00/00:00:00:00:00/e0 tag 0 dma 16384 in
[ 113.651758] res 51/04:20:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 113.651762] ata1.00: status: { DRDY ERR }
[ 113.651764] ata1.00: error: { ABRT }
[ 113.672701] ata1.00: configured for UDMA/100
[ 113.672713] ata1: EH complete
[ 113.819653] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 113.819656] ata1.00: BMDMA2 stat 0x82d0009
[ 113.819662] ata1.00: cmd c8/00:20:00:00:00/00:00:00:00:00/e0 tag 0 dma 16384 in
[ 113.819664] res 51/04:20:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 113.819668] ata1.00: status: { DRDY ERR }
[ 113.819670] ata1.00: error: { ABRT }
[ 113.840702] ata1.00: configured for UDMA/100
[ 113.840714] ata1: EH complete
[ 113.987667] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 113.987670] ata1.00: BMDMA2 stat 0x82d0009
[ 113.987676] ata1.00: cmd c8/00:20:00:00:00/00:00:00:00:00/e0 tag 0 dma 16384 in
[ 113.987678] res 51/04:20:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 113.987681] ata1.00: status: { DRDY ERR }
[ 113.987684] ata1.00: error: { ABRT }
[ 114.008696] ata1.00: configured for UDMA/100
[ 114.008717] sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
[ 114.008722] sd 0:0:0:0: [sda] Sense Key : Aborted Command [current] [descriptor]
[ 114.008728] Descriptor sense data with sense descriptors (in hex):
[ 114.008731] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 114.008741] 00 00 00 00
[ 114.008745] sd 0:0:0:0: [sda] Add. Sense: No additional sense information
[ 114.008750] end_request: I/O error, dev sda, sector 0
[ 114.008756] Buffer I/O error on device sda, logical block 0
[ 114.008764] Buffer I/O error on device sda, logical block 1
[ 114.008767] Buffer I/O error on device sda, logical block 2
[ 114.008770] Buffer I/O error on device sda, logical block 3
[ 114.008787] ata1: EH complete
[ 114.155782] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 114.155786] ata1.00: BMDMA2 stat 0x82d0009
[ 114.155792] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 114.155793] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 114.155797] ata1.00: status: { DRDY ERR }
[ 114.155799] ata1.00: error: { ABRT }
[ 114.176705] ata1.00: configured for UDMA/100
[ 114.176717] ata1: EH complete
[ 114.323690] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 114.323694] ata1.00: BMDMA2 stat 0x82d0009
[ 114.323700] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 114.323701] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 114.323705] ata1.00: status: { DRDY ERR }
[ 114.323707] ata1.00: error: { ABRT }
[ 114.344702] ata1.00: configured for UDMA/100
[ 114.344714] ata1: EH complete
[ 114.491703] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 114.491706] ata1.00: BMDMA2 stat 0x82d0009
[ 114.491712] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 114.491713] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 114.491717] ata1.00: status: { DRDY ERR }
[ 114.491719] ata1.00: error: { ABRT }
[ 114.512700] ata1.00: configured for UDMA/100
[ 114.512712] ata1: EH complete
[ 114.659715] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 114.659718] ata1.00: BMDMA2 stat 0x82d0009
[ 114.659724] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 114.659726] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 114.659729] ata1.00: status: { DRDY ERR }
[ 114.659732] ata1.00: error: { ABRT }
[ 114.680703] ata1.00: configured for UDMA/100
[ 114.680715] ata1: EH complete
[ 114.827727] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 114.827730] ata1.00: BMDMA2 stat 0x82d0009
[ 114.827736] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 114.827738] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 114.827741] ata1.00: status: { DRDY ERR }
[ 114.827744] ata1.00: error: { ABRT }
[ 114.848696] ata1.00: configured for UDMA/100
[ 114.848708] ata1: EH complete
[ 114.995739] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 114.995743] ata1.00: BMDMA2 stat 0x82d0009
[ 114.995749] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 114.995750] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 114.995754] ata1.00: status: { DRDY ERR }
[ 114.995756] ata1.00: error: { ABRT }
[ 115.016703] ata1.00: configured for UDMA/100
[ 115.016715] sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
[ 115.016719] sd 0:0:0:0: [sda] Sense Key : Aborted Command [current] [descriptor]
[ 115.016724] Descriptor sense data with sense descriptors (in hex):
[ 115.016726] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 115.016736] 00 00 00 00
[ 115.016740] sd 0:0:0:0: [sda] Add. Sense: No additional sense information
[ 115.016745] end_request: I/O error, dev sda, sector 0
[ 115.016750] Buffer I/O error on device sda, logical block 0
[ 115.016763] ata1: EH complete
[ 115.017814] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors: (100 GB/93.1 GiB)
[ 115.017854] sd 0:0:0:0: [sda] Write Protect is off
[ 115.017857] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 115.017889] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 115.017926] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors: (100 GB/93.1 GiB)
[ 115.017943] sd 0:0:0:0: [sda] Write Protect is off
[ 115.017946] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 115.017974] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 115.814915] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 115.814920] Bluetooth: BNEP filters: protocol multicast
[ 115.873475] Bridge firewalling registered
[ 121.369404] pci 0000:01:05.0: power state changed by ACPI to D0
[ 121.369420] pci 0000:01:05.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 121.682828] [drm] Initialized drm 1.1.0 20060810
[ 122.123112] [drm] Initialized radeon 1.29.0 20080528 on minor 0
[ 123.517526] lp: driver loaded but no devices found
[ 123.566400] ppdev: user-space parallel port driver
[ 123.616624] [drm] Setting GART location based on new memory map
[ 123.617268] [drm] Loading R300 Microcode
[ 123.617308] [drm] Num pipes: 4
[ 123.617315] [drm] writeback test succeeded in 1 usecs
[ 125.977670] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
[ 126.008123] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 133.769801] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 133.769809] ata1.00: BMDMA2 stat 0x82d0009
[ 133.769817] ata1.00: cmd c8/00:20:00:00:00/00:00:00:00:00/e0 tag 0 dma 16384 in
[ 133.769819] res 51/04:20:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 133.769823] ata1.00: status: { DRDY ERR }
[ 133.769825] ata1.00: error: { ABRT }
[ 133.792762] ata1.00: configured for UDMA/100
[ 133.792777] ata1: EH complete
[ 133.939885] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 133.939892] ata1.00: BMDMA2 stat 0x82d0009
[ 133.939901] ata1.00: cmd c8/00:20:00:00:00/00:00:00:00:00/e0 tag 0 dma 16384 in
[ 133.939903] res 51/04:20:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 133.939906] ata1.00: status: { DRDY ERR }
[ 133.939909] ata1.00: error: { ABRT }
[ 133.967790] ata1.00: configured for UDMA/100
[ 133.967824] ata1: EH complete
[ 134.115238] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 134.115245] ata1.00: BMDMA2 stat 0x82d0009
[ 134.115253] ata1.00: cmd c8/00:20:00:00:00/00:00:00:00:00/e0 tag 0 dma 16384 in
[ 134.115255] res 51/04:20:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 134.115259] ata1.00: status: { DRDY ERR }
[ 134.115261] ata1.00: error: { ABRT }
[ 134.136792] ata1.00: configured for UDMA/100
[ 134.136810] ata1: EH complete
[ 134.283916] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 134.283922] ata1.00: BMDMA2 stat 0x82d0009
[ 134.283929] ata1.00: cmd c8/00:20:00:00:00/00:00:00:00:00/e0 tag 0 dma 16384 in
[ 134.283931] res 51/04:20:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 134.283935] ata1.00: status: { DRDY ERR }
[ 134.283937] ata1.00: error: { ABRT }
[ 134.308798] ata1.00: configured for UDMA/100
[ 134.308812] ata1: EH complete
[ 134.459584] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 134.459590] ata1.00: BMDMA2 stat 0x82d0009
[ 134.459598] ata1.00: cmd c8/00:20:00:00:00/00:00:00:00:00/e0 tag 0 dma 16384 in
[ 134.459599] res 51/04:20:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 134.459603] ata1.00: status: { DRDY ERR }
[ 134.459606] ata1.00: error: { ABRT }
[ 134.480732] ata1.00: configured for UDMA/100
[ 134.480754] ata1: EH complete
[ 134.627848] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 134.627853] ata1.00: BMDMA2 stat 0x82d0009
[ 134.627859] ata1.00: cmd c8/00:20:00:00:00/00:00:00:00:00/e0 tag 0 dma 16384 in
[ 134.627861] res 51/04:20:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 134.627864] ata1.00: status: { DRDY ERR }
[ 134.627867] ata1.00: error: { ABRT }
[ 134.648771] ata1.00: configured for UDMA/100
[ 134.648792] sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
[ 134.648797] sd 0:0:0:0: [sda] Sense Key : Aborted Command [current] [descriptor]
[ 134.648803] Descriptor sense data with sense descriptors (in hex):
[ 134.648806] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 134.648816] 00 00 00 00
[ 134.648820] sd 0:0:0:0: [sda] Add. Sense: No additional sense information
[ 134.648826] end_request: I/O error, dev sda, sector 0
[ 134.648831] Buffer I/O error on device sda, logical block 0
[ 134.648836] Buffer I/O error on device sda, logical block 1
[ 134.648839] Buffer I/O error on device sda, logical block 2
[ 134.648842] Buffer I/O error on device sda, logical block 3
[ 134.648852] ata1: EH complete
[ 134.795993] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 134.796000] ata1.00: BMDMA2 stat 0x82d0009
[ 134.796030] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 134.796032] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 134.796036] ata1.00: status: { DRDY ERR }
[ 134.796038] ata1.00: error: { ABRT }
[ 134.820730] ata1.00: configured for UDMA/100
[ 134.820750] ata1: EH complete
[ 134.967841] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 134.967847] ata1.00: BMDMA2 stat 0x82d0009
[ 134.967855] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 134.967857] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 134.967861] ata1.00: status: { DRDY ERR }
[ 134.967863] ata1.00: error: { ABRT }
[ 134.992767] ata1.00: configured for UDMA/100
[ 134.992786] ata1: EH complete
[ 135.139833] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 135.139840] ata1.00: BMDMA2 stat 0x82d0009
[ 135.139848] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 135.139850] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 135.139854] ata1.00: status: { DRDY ERR }
[ 135.139856] ata1.00: error: { ABRT }
[ 135.160736] ata1.00: configured for UDMA/100
[ 135.160755] ata1: EH complete
[ 135.307846] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 135.307853] ata1.00: BMDMA2 stat 0x82d0009
[ 135.307861] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 135.307863] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 135.307866] ata1.00: status: { DRDY ERR }
[ 135.307869] ata1.00: error: { ABRT }
[ 135.332749] ata1.00: configured for UDMA/100
[ 135.332772] ata1: EH complete
[ 135.479817] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 135.479823] ata1.00: BMDMA2 stat 0x82d0009
[ 135.479832] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 135.479833] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 135.479837] ata1.00: status: { DRDY ERR }
[ 135.479840] ata1.00: error: { ABRT }
[ 135.504277] ata1.00: configured for UDMA/100
[ 135.504313] ata1: EH complete
[ 135.651357] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 135.651364] ata1.00: BMDMA2 stat 0x82d0009
[ 135.651372] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 135.651374] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 135.651378] ata1.00: status: { DRDY ERR }
[ 135.651380] ata1.00: error: { ABRT }
[ 135.672758] ata1.00: configured for UDMA/100
[ 135.672780] sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
[ 135.672786] sd 0:0:0:0: [sda] Sense Key : Aborted Command [current] [descriptor]
[ 135.672792] Descriptor sense data with sense descriptors (in hex):
[ 135.672795] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 135.672805] 00 00 00 00
[ 135.672809] sd 0:0:0:0: [sda] Add. Sense: No additional sense information
[ 135.672814] end_request: I/O error, dev sda, sector 0
[ 135.672820] Buffer I/O error on device sda, logical block 0
[ 135.672841] ata1: EH complete
[ 135.674229] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors: (100 GB/93.1 GiB)
[ 135.675756] sd 0:0:0:0: [sda] Write Protect is off
[ 135.675761] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 135.675824] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 135.675865] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors: (100 GB/93.1 GiB)
[ 135.675882] sd 0:0:0:0: [sda] Write Protect is off
[ 135.675885] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 135.675913] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 136.900045] eth0: no IPv6 routers present
[ 221.400057] usb 1-1: new high speed USB device using ehci_hcd and address 4
[ 221.557057] usb 1-1: configuration #1 chosen from 1 choice
[ 221.669995] Initializing USB Mass Storage driver...
[ 221.670451] scsi4 : SCSI emulation for USB Mass Storage devices
[ 221.670572] usbcore: registered new interface driver usb-storage
[ 221.670576] USB Mass Storage support registered.
[ 221.697314] usb-storage: device found at 4
[ 221.697319] usb-storage: waiting for device to settle before scanning
[ 226.696329] usb-storage: device scan complete
[ 226.697429] scsi 4:0:0:0: Direct-Access USB 2.0 Flash Disk 1100 PQ: 0 ANSI: 0 CCS
[ 226.736912] sd 4:0:0:0: [sdb] 1981440 512-byte hardware sectors: (1.01 GB/967 MiB)
[ 226.737861] sd 4:0:0:0: [sdb] Write Protect is off
[ 226.737866] sd 4:0:0:0: [sdb] Mode Sense: 43 00 00 00
[ 226.737869] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[ 226.742166] sd 4:0:0:0: [sdb] 1981440 512-byte hardware sectors: (1.01 GB/967 MiB)
[ 226.743024] sd 4:0:0:0: [sdb] Write Protect is off
[ 226.743027] sd 4:0:0:0: [sdb] Mode Sense: 43 00 00 00
[ 226.743030] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[ 226.743038] sdb: sdb1
[ 226.847611] sd 4:0:0:0: [sdb] Attached SCSI removable disk
[ 226.847706] sd 4:0:0:0: Attached scsi generic sg2 type 0
[ 402.244499] pcmcia: Detected deprecated PCMCIA ioctl usage from process: lshw.
[ 402.244504] pcmcia: This interface will soon be removed from the kernel; please expect breakage unless you upgrade to new tools.
[ 402.244508] pcmcia: see http://www.kernel.org/pub/linux/utils/kernel/pcmcia/pcmcia.html for details.
[ 402.397437] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 402.397443] ata1.00: BMDMA2 stat 0x82d0009
[ 402.397452] ata1.00: cmd c8/00:20:00:00:00/00:00:00:00:00/e0 tag 0 dma 16384 in
[ 402.397454] res 51/04:20:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 402.397457] ata1.00: status: { DRDY ERR }
[ 402.397460] ata1.00: error: { ABRT }
[ 402.420733] ata1.00: configured for UDMA/100
[ 402.420751] ata1: EH complete
[ 402.567822] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 402.567825] ata1.00: BMDMA2 stat 0x82d0009
[ 402.567831] ata1.00: cmd c8/00:20:00:00:00/00:00:00:00:00/e0 tag 0 dma 16384 in
[ 402.567833] res 51/04:20:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 402.567836] ata1.00: status: { DRDY ERR }
[ 402.567839] ata1.00: error: { ABRT }
[ 402.588749] ata1.00: configured for UDMA/100
[ 402.588762] ata1: EH complete
[ 402.735834] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 402.735837] ata1.00: BMDMA2 stat 0x82d0009
[ 402.735843] ata1.00: cmd c8/00:20:00:00:00/00:00:00:00:00/e0 tag 0 dma 16384 in
[ 402.735845] res 51/04:20:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 402.735848] ata1.00: status: { DRDY ERR }
[ 402.735851] ata1.00: error: { ABRT }
[ 402.756732] ata1.00: configured for UDMA/100
[ 402.756744] ata1: EH complete
[ 402.903752] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 402.903758] ata1.00: BMDMA2 stat 0x82d0009
[ 402.903766] ata1.00: cmd c8/00:20:00:00:00/00:00:00:00:00/e0 tag 0 dma 16384 in
[ 402.903768] res 51/04:20:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 402.903772] ata1.00: status: { DRDY ERR }
[ 402.903774] ata1.00: error: { ABRT }
[ 402.924756] ata1.00: configured for UDMA/100
[ 402.924777] ata1: EH complete
[ 403.071862] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 403.071866] ata1.00: BMDMA2 stat 0x82d0009
[ 403.071872] ata1.00: cmd c8/00:20:00:00:00/00:00:00:00:00/e0 tag 0 dma 16384 in
[ 403.071874] res 51/04:20:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 403.071877] ata1.00: status: { DRDY ERR }
[ 403.071880] ata1.00: error: { ABRT }
[ 403.096754] ata1.00: configured for UDMA/100
[ 403.096766] ata1: EH complete
[ 403.243809] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 403.243813] ata1.00: BMDMA2 stat 0x82d0009
[ 403.243818] ata1.00: cmd c8/00:20:00:00:00/00:00:00:00:00/e0 tag 0 dma 16384 in
[ 403.243820] res 51/04:20:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 403.243824] ata1.00: status: { DRDY ERR }
[ 403.243826] ata1.00: error: { ABRT }
[ 403.264875] ata1.00: configured for UDMA/100
[ 403.264894] sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
[ 403.264899] sd 0:0:0:0: [sda] Sense Key : Aborted Command [current] [descriptor]
[ 403.264905] Descriptor sense data with sense descriptors (in hex):
[ 403.264908] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 403.264918] 00 00 00 00
[ 403.264922] sd 0:0:0:0: [sda] Add. Sense: No additional sense information
[ 403.264928] end_request: I/O error, dev sda, sector 0
[ 403.264934] Buffer I/O error on device sda, logical block 0
[ 403.264941] Buffer I/O error on device sda, logical block 1
[ 403.264945] Buffer I/O error on device sda, logical block 2
[ 403.264948] Buffer I/O error on device sda, logical block 3
[ 403.264960] ata1: EH complete
[ 403.265086] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors: (100 GB/93.1 GiB)
[ 403.265107] sd 0:0:0:0: [sda] Write Protect is off
[ 403.265110] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 403.265141] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 403.265174] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors: (100 GB/93.1 GiB)
[ 403.265191] sd 0:0:0:0: [sda] Write Protect is off
[ 403.265194] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 403.265222] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 403.412239] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 403.412243] ata1.00: BMDMA2 stat 0x82d0009
[ 403.412249] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 403.412250] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 403.412254] ata1.00: status: { DRDY ERR }
[ 403.412257] ata1.00: error: { ABRT }
[ 403.436749] ata1.00: configured for UDMA/100
[ 403.436778] ata1: EH complete
[ 403.583798] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 403.583803] ata1.00: BMDMA2 stat 0x82d0009
[ 403.583811] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 403.583812] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 403.583816] ata1.00: status: { DRDY ERR }
[ 403.583819] ata1.00: error: { ABRT }
[ 403.604757] ata1.00: configured for UDMA/100
[ 403.604769] ata1: EH complete
[ 403.751809] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 403.751813] ata1.00: BMDMA2 stat 0x82d0009
[ 403.751819] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 403.751820] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 403.751824] ata1.00: status: { DRDY ERR }
[ 403.751826] ata1.00: error: { ABRT }
[ 403.772734] ata1.00: configured for UDMA/100
[ 403.772745] ata1: EH complete
[ 403.919730] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 403.919733] ata1.00: BMDMA2 stat 0x82d0009
[ 403.919739] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 403.919741] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 403.919744] ata1.00: status: { DRDY ERR }
[ 403.919747] ata1.00: error: { ABRT }
[ 403.940730] ata1.00: configured for UDMA/100
[ 403.940742] ata1: EH complete
[ 404.087850] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 404.087856] ata1.00: BMDMA2 stat 0x82d0009
[ 404.087864] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 404.087865] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 404.087869] ata1.00: status: { DRDY ERR }
[ 404.087872] ata1.00: error: { ABRT }
[ 404.112732] ata1.00: configured for UDMA/100
[ 404.112752] ata1: EH complete
[ 404.259811] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 404.259814] ata1.00: BMDMA2 stat 0x82d0009
[ 404.259820] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 404.259822] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 404.259825] ata1.00: status: { DRDY ERR }
[ 404.259828] ata1.00: error: { ABRT }
[ 404.280744] ata1.00: configured for UDMA/100
[ 404.280762] sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
[ 404.280767] sd 0:0:0:0: [sda] Sense Key : Aborted Command [current] [descriptor]
[ 404.280773] Descriptor sense data with sense descriptors (in hex):
[ 404.280775] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 404.280786] 00 00 00 00
[ 404.280790] sd 0:0:0:0: [sda] Add. Sense: No additional sense information
[ 404.280795] end_request: I/O error, dev sda, sector 0
[ 404.280801] Buffer I/O error on device sda, logical block 0
[ 404.280822] ata1: EH complete
[ 404.280880] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors: (100 GB/93.1 GiB)
[ 404.280901] sd 0:0:0:0: [sda] Write Protect is off
[ 404.280904] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 404.280935] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 404.280971] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors: (100 GB/93.1 GiB)
[ 404.280988] sd 0:0:0:0: [sda] Write Protect is off
[ 404.280991] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 404.281019] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 404.428139] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 404.428143] ata1.00: BMDMA2 stat 0x82d0009
[ 404.428149] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 404.428151] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 404.428154] ata1.00: status: { DRDY ERR }
[ 404.428157] ata1.00: error: { ABRT }
[ 404.452736] ata1.00: configured for UDMA/100
[ 404.452751] ata1: EH complete
[ 404.599791] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 404.599794] ata1.00: BMDMA2 stat 0x82d0009
[ 404.599801] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 404.599802] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 404.599806] ata1.00: status: { DRDY ERR }
[ 404.599808] ata1.00: error: { ABRT }
[ 404.620729] ata1.00: configured for UDMA/100
[ 404.620741] ata1: EH complete
[ 404.767836] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 404.767841] ata1.00: BMDMA2 stat 0x82d0009
[ 404.767849] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 404.767851] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 404.767854] ata1.00: status: { DRDY ERR }
[ 404.767857] ata1.00: error: { ABRT }
[ 404.788749] ata1.00: configured for UDMA/100
[ 404.788769] ata1: EH complete
[ 404.935804] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 404.935807] ata1.00: BMDMA2 stat 0x82d0009
[ 404.935813] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 404.935815] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 404.935819] ata1.00: status: { DRDY ERR }
[ 404.935821] ata1.00: error: { ABRT }
[ 404.956735] ata1.00: configured for UDMA/100
[ 404.956746] ata1: EH complete
[ 405.103731] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 405.103734] ata1.00: BMDMA2 stat 0x82d0009
[ 405.103740] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 405.103742] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 405.103746] ata1.00: status: { DRDY ERR }
[ 405.103748] ata1.00: error: { ABRT }
[ 405.124755] ata1.00: configured for UDMA/100
[ 405.124768] ata1: EH complete
[ 405.271865] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 405.271871] ata1.00: BMDMA2 stat 0x82d0009
[ 405.271879] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 405.271880] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 405.271884] ata1.00: status: { DRDY ERR }
[ 405.271887] ata1.00: error: { ABRT }
[ 405.296752] ata1.00: configured for UDMA/100
[ 405.296769] sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
[ 405.296775] sd 0:0:0:0: [sda] Sense Key : Aborted Command [current] [descriptor]
[ 405.296781] Descriptor sense data with sense descriptors (in hex):
[ 405.296784] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 405.296794] 00 00 00 00
[ 405.296798] sd 0:0:0:0: [sda] Add. Sense: No additional sense information
[ 405.296804] end_request: I/O error, dev sda, sector 0
[ 405.296809] Buffer I/O error on device sda, logical block 0
[ 405.296827] ata1: EH complete
[ 405.296873] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors: (100 GB/93.1 GiB)
[ 405.296894] sd 0:0:0:0: [sda] Write Protect is off
[ 405.296897] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 405.296927] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 405.296961] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors: (100 GB/93.1 GiB)
[ 405.296978] sd 0:0:0:0: [sda] Write Protect is off
[ 405.296981] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 405.297009] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 405.444113] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 405.444117] ata1.00: BMDMA2 stat 0x82d0009
[ 405.444123] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 405.444124] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 405.444128] ata1.00: status: { DRDY ERR }
[ 405.444130] ata1.00: error: { ABRT }
[ 405.468749] ata1.00: configured for UDMA/100
[ 405.468760] ata1: EH complete
[ 405.615789] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 405.615792] ata1.00: BMDMA2 stat 0x82d0009
[ 405.615798] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 405.615800] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 405.615803] ata1.00: status: { DRDY ERR }
[ 405.615806] ata1.00: error: { ABRT }
[ 405.636731] ata1.00: configured for UDMA/100
[ 405.636743] ata1: EH complete
[ 405.783781] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 405.783785] ata1.00: BMDMA2 stat 0x82d0009
[ 405.783791] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 405.783792] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 405.783796] ata1.00: status: { DRDY ERR }
[ 405.783798] ata1.00: error: { ABRT }
[ 405.804756] ata1.00: configured for UDMA/100
[ 405.804769] ata1: EH complete
[ 405.951832] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 405.951838] ata1.00: BMDMA2 stat 0x82d0009
[ 405.951846] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 405.951847] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 405.951851] ata1.00: status: { DRDY ERR }
[ 405.951854] ata1.00: error: { ABRT }
[ 405.972736] ata1.00: configured for UDMA/100
[ 405.972757] ata1: EH complete
[ 406.119825] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 406.119829] ata1.00: BMDMA2 stat 0x82d0009
[ 406.119835] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 406.119836] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 406.119840] ata1.00: status: { DRDY ERR }
[ 406.119842] ata1.00: error: { ABRT }
[ 406.140731] ata1.00: configured for UDMA/100
[ 406.140742] ata1: EH complete
[ 406.287817] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 406.287820] ata1.00: BMDMA2 stat 0x82d0009
[ 406.287826] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 406.287828] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 406.287831] ata1.00: status: { DRDY ERR }
[ 406.287834] ata1.00: error: { ABRT }
[ 406.308745] ata1.00: configured for UDMA/100
[ 406.308763] sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
[ 406.308768] sd 0:0:0:0: [sda] Sense Key : Aborted Command [current] [descriptor]
[ 406.308774] Descriptor sense data with sense descriptors (in hex):
[ 406.308777] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 406.308787] 00 00 00 00
[ 406.308791] sd 0:0:0:0: [sda] Add. Sense: No additional sense information
[ 406.308796] end_request: I/O error, dev sda, sector 0
[ 406.308802] Buffer I/O error on device sda, logical block 0
[ 406.308823] ata1: EH complete
[ 406.455967] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 406.455973] ata1.00: BMDMA2 stat 0x82d0009
[ 406.455981] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 406.455983] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 406.455987] ata1.00: status: { DRDY ERR }
[ 406.455989] ata1.00: error: { ABRT }
[ 406.480743] ata1.00: configured for UDMA/100
[ 406.480764] ata1: EH complete
[ 406.627800] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 406.627804] ata1.00: BMDMA2 stat 0x82d0009
[ 406.627810] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 406.627812] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 406.627815] ata1.00: status: { DRDY ERR }
[ 406.627818] ata1.00: error: { ABRT }
[ 406.648732] ata1.00: configured for UDMA/100
[ 406.648744] ata1: EH complete
[ 406.795824] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 406.795827] ata1.00: BMDMA2 stat 0x82d0009
[ 406.795833] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 406.795835] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 406.795839] ata1.00: status: { DRDY ERR }
[ 406.795841] ata1.00: error: { ABRT }
[ 406.816751] ata1.00: configured for UDMA/100
[ 406.816763] ata1: EH complete
[ 406.963844] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 406.963847] ata1.00: BMDMA2 stat 0x82d0009
[ 406.963853] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 406.963855] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 406.963858] ata1.00: status: { DRDY ERR }
[ 406.963861] ata1.00: error: { ABRT }
[ 406.984731] ata1.00: configured for UDMA/100
[ 406.984742] ata1: EH complete
[ 407.131759] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 407.131764] ata1.00: BMDMA2 stat 0x82d0009
[ 407.131772] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 407.131774] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 407.131777] ata1.00: status: { DRDY ERR }
[ 407.131780] ata1.00: error: { ABRT }
[ 407.152757] ata1.00: configured for UDMA/100
[ 407.152778] ata1: EH complete
[ 407.299871] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 407.299876] ata1.00: BMDMA2 stat 0x82d0009
[ 407.299883] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 407.299885] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 407.299889] ata1.00: status: { DRDY ERR }
[ 407.299892] ata1.00: error: { ABRT }
[ 407.324957] ata1.00: configured for UDMA/100
[ 407.324975] sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
[ 407.324980] sd 0:0:0:0: [sda] Sense Key : Aborted Command [current] [descriptor]
[ 407.324986] Descriptor sense data with sense descriptors (in hex):
[ 407.324988] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 407.324998] 00 00 00 00
[ 407.325003] sd 0:0:0:0: [sda] Add. Sense: No additional sense information
[ 407.325008] end_request: I/O error, dev sda, sector 0
[ 407.325014] Buffer I/O error on device sda, logical block 0
[ 407.325031] ata1: EH complete
[ 407.325162] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors: (100 GB/93.1 GiB)
[ 407.472175] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 407.472183] ata1.00: BMDMA2 stat 0x82d0009
[ 407.472192] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 407.472193] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 407.472197] ata1.00: status: { DRDY ERR }
[ 407.472200] ata1.00: error: { ABRT }
[ 407.496751] ata1.00: configured for UDMA/100
[ 407.496775] ata1: EH complete
[ 407.643831] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 407.643837] ata1.00: BMDMA2 stat 0x82d0009
[ 407.643845] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 407.643847] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 407.643850] ata1.00: status: { DRDY ERR }
[ 407.643853] ata1.00: error: { ABRT }
[ 407.664733] ata1.00: configured for UDMA/100
[ 407.664754] ata1: EH complete
[ 407.811819] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 407.811822] ata1.00: BMDMA2 stat 0x82d0009
[ 407.811828] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 407.811830] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 407.811834] ata1.00: status: { DRDY ERR }
[ 407.811836] ata1.00: error: { ABRT }
[ 407.832756] ata1.00: configured for UDMA/100
[ 407.832768] ata1: EH complete
[ 407.979813] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 407.979817] ata1.00: BMDMA2 stat 0x82d0009
[ 407.979823] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 407.979824] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 407.979828] ata1.00: status: { DRDY ERR }
[ 407.979830] ata1.00: error: { ABRT }
[ 408.000736] ata1.00: configured for UDMA/100
[ 408.000748] ata1: EH complete
[ 408.147750] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 408.147754] ata1.00: BMDMA2 stat 0x82d0009
[ 408.147761] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 408.147762] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 408.147766] ata1.00: status: { DRDY ERR }
[ 408.147768] ata1.00: error: { ABRT }
[ 408.168731] ata1.00: configured for UDMA/100
[ 408.168744] ata1: EH complete
[ 408.315749] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 408.315755] ata1.00: BMDMA2 stat 0x82d0009
[ 408.315763] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 408.315764] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 408.315768] ata1.00: status: { DRDY ERR }
[ 408.315771] ata1.00: error: { ABRT }
[ 408.336749] ata1.00: configured for UDMA/100
[ 408.336772] sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
[ 408.336777] sd 0:0:0:0: [sda] Sense Key : Aborted Command [current] [descriptor]
[ 408.336783] Descriptor sense data with sense descriptors (in hex):
[ 408.336786] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 408.336796] 00 00 00 00
[ 408.336800] sd 0:0:0:0: [sda] Add. Sense: No additional sense information
[ 408.336806] end_request: I/O error, dev sda, sector 0
[ 408.336812] Buffer I/O error on device sda, logical block 0
[ 408.336839] ata1: EH complete
[ 408.337024] sd 0:0:0:0: [sda] Write Protect is off
[ 408.337027] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 408.483953] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 408.483957] ata1.00: BMDMA2 stat 0x82d0009
[ 408.483963] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 408.483965] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 408.483968] ata1.00: status: { DRDY ERR }
[ 408.483971] ata1.00: error: { ABRT }
[ 408.508748] ata1.00: configured for UDMA/100
[ 408.508761] ata1: EH complete
[ 408.655838] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 408.655842] ata1.00: BMDMA2 stat 0x82d0009
[ 408.655847] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 408.655849] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 408.655853] ata1.00: status: { DRDY ERR }
[ 408.655855] ata1.00: error: { ABRT }
[ 408.676735] ata1.00: configured for UDMA/100
[ 408.676746] ata1: EH complete
[ 408.823732] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 408.823735] ata1.00: BMDMA2 stat 0x82d0009
[ 408.823741] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 408.823743] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 408.823746] ata1.00: status: { DRDY ERR }
[ 408.823749] ata1.00: error: { ABRT }
[ 408.844758] ata1.00: configured for UDMA/100
[ 408.844782] ata1: EH complete
[ 408.991863] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 408.991867] ata1.00: BMDMA2 stat 0x82d0009
[ 408.991875] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 408.991877] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 408.991880] ata1.00: status: { DRDY ERR }
[ 408.991883] ata1.00: error: { ABRT }
[ 409.016818] ata1.00: configured for UDMA/100
[ 409.016831] ata1: EH complete
[ 409.163813] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 409.163816] ata1.00: BMDMA2 stat 0x82d0009
[ 409.163822] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 409.163824] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 409.163828] ata1.00: status: { DRDY ERR }
[ 409.163830] ata1.00: error: { ABRT }
[ 409.184737] ata1.00: configured for UDMA/100
[ 409.184748] ata1: EH complete
[ 409.331736] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 409.331741] ata1.00: BMDMA2 stat 0x82d0009
[ 409.331747] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 409.331748] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 409.331752] ata1.00: status: { DRDY ERR }
[ 409.331754] ata1.00: error: { ABRT }
[ 409.352754] ata1.00: configured for UDMA/100
[ 409.352769] sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
[ 409.352774] sd 0:0:0:0: [sda] Sense Key : Aborted Command [current] [descriptor]
[ 409.352780] Descriptor sense data with sense descriptors (in hex):
[ 409.352783] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 409.352793] 00 00 00 00
[ 409.352797] sd 0:0:0:0: [sda] Add. Sense: No additional sense information
[ 409.352803] end_request: I/O error, dev sda, sector 0
[ 409.352808] Buffer I/O error on device sda, logical block 0
[ 409.352824] ata1: EH complete
[ 409.499979] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 409.499985] ata1.00: BMDMA2 stat 0x82d0009
[ 409.499993] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 409.499995] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 409.499999] ata1.00: status: { DRDY ERR }
[ 409.500022] ata1.00: error: { ABRT }
[ 409.524756] ata1.00: configured for UDMA/100
[ 409.524776] ata1: EH complete
[ 409.671808] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 409.671812] ata1.00: BMDMA2 stat 0x82d0009
[ 409.671818] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 409.671819] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 409.671823] ata1.00: status: { DRDY ERR }
[ 409.671825] ata1.00: error: { ABRT }
[ 409.692733] ata1.00: configured for UDMA/100
[ 409.692745] ata1: EH complete
[ 409.839736] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 409.839739] ata1.00: BMDMA2 stat 0x82d0009
[ 409.839745] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 409.839747] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 409.839750] ata1.00: status: { DRDY ERR }
[ 409.839753] ata1.00: error: { ABRT }
[ 409.860731] ata1.00: configured for UDMA/100
[ 409.860742] ata1: EH complete
[ 410.007721] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 410.007724] ata1.00: BMDMA2 stat 0x82d0009
[ 410.007730] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 410.007731] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 410.007735] ata1.00: status: { DRDY ERR }
[ 410.007737] ata1.00: error: { ABRT }
[ 410.030245] ata1.00: configured for UDMA/100
[ 410.030275] ata1: EH complete
[ 410.177326] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 410.177331] ata1.00: BMDMA2 stat 0x82d0009
[ 410.177338] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 410.177340] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 410.177344] ata1.00: status: { DRDY ERR }
[ 410.177346] ata1.00: error: { ABRT }
[ 410.200730] ata1.00: configured for UDMA/100
[ 410.200742] ata1: EH complete
[ 410.347727] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 410.347730] ata1.00: BMDMA2 stat 0x82d0009
[ 410.347736] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 410.347738] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 410.347741] ata1.00: status: { DRDY ERR }
[ 410.347744] ata1.00: error: { ABRT }
[ 410.368729] ata1.00: configured for UDMA/100
[ 410.368747] sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
[ 410.368752] sd 0:0:0:0: [sda] Sense Key : Aborted Command [current] [descriptor]
[ 410.368759] Descriptor sense data with sense descriptors (in hex):
[ 410.368761] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 410.368771] 00 00 00 00
[ 410.368775] sd 0:0:0:0: [sda] Add. Sense: No additional sense information
[ 410.368781] end_request: I/O error, dev sda, sector 0
[ 410.368787] Buffer I/O error on device sda, logical block 0
[ 410.368807] ata1: EH complete
[ 410.368953] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 410.515925] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 410.515929] ata1.00: BMDMA2 stat 0x82d0009
[ 410.515935] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 410.515936] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 410.515940] ata1.00: status: { DRDY ERR }
[ 410.515942] ata1.00: error: { ABRT }
[ 410.540730] ata1.00: configured for UDMA/100
[ 410.540742] ata1: EH complete
[ 410.687841] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 410.687847] ata1.00: BMDMA2 stat 0x82d0009
[ 410.687855] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 410.687856] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 410.687860] ata1.00: status: { DRDY ERR }
[ 410.687863] ata1.00: error: { ABRT }
[ 410.708744] ata1.00: configured for UDMA/100
[ 410.708765] ata1: EH complete
[ 410.855805] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 410.855809] ata1.00: BMDMA2 stat 0x82d0009
[ 410.855815] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 410.855817] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 410.855820] ata1.00: status: { DRDY ERR }
[ 410.855823] ata1.00: error: { ABRT }
[ 410.876731] ata1.00: configured for UDMA/100
[ 410.876744] ata1: EH complete
[ 411.023732] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 411.023736] ata1.00: BMDMA2 stat 0x82d0009
[ 411.023742] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 411.023744] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 411.023747] ata1.00: status: { DRDY ERR }
[ 411.023750] ata1.00: error: { ABRT }
[ 411.044755] ata1.00: configured for UDMA/100
[ 411.044767] ata1: EH complete
[ 411.191850] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 411.191854] ata1.00: BMDMA2 stat 0x82d0009
[ 411.191860] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 411.191861] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 411.191865] ata1.00: status: { DRDY ERR }
[ 411.191867] ata1.00: error: { ABRT }
[ 411.212730] ata1.00: configured for UDMA/100
[ 411.212741] ata1: EH complete
[ 411.359754] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 411.359760] ata1.00: BMDMA2 stat 0x82d0009
[ 411.359768] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 411.359770] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 411.359773] ata1.00: status: { DRDY ERR }
[ 411.359776] ata1.00: error: { ABRT }
[ 411.380730] ata1.00: configured for UDMA/100
[ 411.380749] sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
[ 411.380754] sd 0:0:0:0: [sda] Sense Key : Aborted Command [current] [descriptor]
[ 411.380760] Descriptor sense data with sense descriptors (in hex):
[ 411.380762] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 411.380773] 00 00 00 00
[ 411.380777] sd 0:0:0:0: [sda] Add. Sense: No additional sense information
[ 411.380782] end_request: I/O error, dev sda, sector 0
[ 411.380788] Buffer I/O error on device sda, logical block 0
[ 411.380804] ata1: EH complete
[ 411.527963] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 411.527966] ata1.00: BMDMA2 stat 0x82d0009
[ 411.527973] ata1.00: cmd c8/00:08:80:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 411.527974] res 51/04:08:80:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 411.527978] ata1.00: status: { DRDY ERR }
[ 411.527980] ata1.00: error: { ABRT }
[ 411.552756] ata1.00: configured for UDMA/100
[ 411.552769] ata1: EH complete
[ 411.699823] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 411.699827] ata1.00: BMDMA2 stat 0x82d0009
[ 411.699833] ata1.00: cmd c8/00:08:80:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 411.699835] res 51/04:08:80:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 411.699838] ata1.00: status: { DRDY ERR }
[ 411.699841] ata1.00: error: { ABRT }
[ 411.720734] ata1.00: configured for UDMA/100
[ 411.720747] ata1: EH complete
[ 411.867765] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 411.867771] ata1.00: BMDMA2 stat 0x82d0009
[ 411.867778] ata1.00: cmd c8/00:08:80:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 411.867780] res 51/04:08:80:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 411.867784] ata1.00: status: { DRDY ERR }
[ 411.867786] ata1.00: error: { ABRT }
[ 411.888734] ata1.00: configured for UDMA/100
[ 411.888754] ata1: EH complete
[ 412.035768] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 412.035772] ata1.00: BMDMA2 stat 0x82d0009
[ 412.035778] ata1.00: cmd c8/00:08:80:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 412.035779] res 51/04:08:80:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 412.035783] ata1.00: status: { DRDY ERR }
[ 412.035785] ata1.00: error: { ABRT }
[ 412.056748] ata1.00: configured for UDMA/100
[ 412.056761] ata1: EH complete
[ 412.203755] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 412.203758] ata1.00: BMDMA2 stat 0x82d0009
[ 412.203764] ata1.00: cmd c8/00:08:80:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 412.203766] res 51/04:08:80:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 412.203769] ata1.00: status: { DRDY ERR }
[ 412.203772] ata1.00: error: { ABRT }
[ 412.224732] ata1.00: configured for UDMA/100
[ 412.224744] ata1: EH complete
[ 412.371777] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 412.371780] ata1.00: BMDMA2 stat 0x82d0009
[ 412.371786] ata1.00: cmd c8/00:08:80:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 412.371788] res 51/04:08:80:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 412.371791] ata1.00: status: { DRDY ERR }
[ 412.371794] ata1.00: error: { ABRT }
[ 412.392755] ata1.00: configured for UDMA/100
[ 412.392773] sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
[ 412.392778] sd 0:0:0:0: [sda] Sense Key : Aborted Command [current] [descriptor]
[ 412.392784] Descriptor sense data with sense descriptors (in hex):
[ 412.392787] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 412.392797] 00 00 00 80
[ 412.392801] sd 0:0:0:0: [sda] Add. Sense: No additional sense information
[ 412.392807] end_request: I/O error, dev sda, sector 128
[ 412.392813] Buffer I/O error on device sda, logical block 16
[ 412.392833] ata1: EH complete
[ 412.392970] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors: (100 GB/93.1 GiB)
[ 412.539925] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 412.539931] ata1.00: BMDMA2 stat 0x82d0009
[ 412.539939] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 412.539940] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 412.539944] ata1.00: status: { DRDY ERR }
[ 412.539947] ata1.00: error: { ABRT }
[ 412.564753] ata1.00: configured for UDMA/100
[ 412.564774] ata1: EH complete
[ 412.711855] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 412.711858] ata1.00: BMDMA2 stat 0x82d0009
[ 412.711864] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 412.711866] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 412.711870] ata1.00: status: { DRDY ERR }
[ 412.711872] ata1.00: error: { ABRT }
[ 412.732732] ata1.00: configured for UDMA/100
[ 412.732743] ata1: EH complete
[ 412.879784] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 412.879787] ata1.00: BMDMA2 stat 0x82d0009
[ 412.879793] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 412.879795] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 412.879798] ata1.00: status: { DRDY ERR }
[ 412.879801] ata1.00: error: { ABRT }
[ 412.900730] ata1.00: configured for UDMA/100
[ 412.900741] ata1: EH complete
[ 413.047801] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 413.047806] ata1.00: BMDMA2 stat 0x82d0009
[ 413.047814] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 413.047816] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 413.047820] ata1.00: status: { DRDY ERR }
[ 413.047822] ata1.00: error: { ABRT }
[ 413.068740] ata1.00: configured for UDMA/100
[ 413.068761] ata1: EH complete
[ 413.215791] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 413.215794] ata1.00: BMDMA2 stat 0x82d0009
[ 413.215800] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 413.215802] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 413.215806] ata1.00: status: { DRDY ERR }
[ 413.215808] ata1.00: error: { ABRT }
[ 413.236730] ata1.00: configured for UDMA/100
[ 413.236742] ata1: EH complete
[ 413.383822] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 413.383826] ata1.00: BMDMA2 stat 0x82d0009
[ 413.383832] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 413.383834] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 413.383838] ata1.00: status: { DRDY ERR }
[ 413.383840] ata1.00: error: { ABRT }
[ 413.404749] ata1.00: configured for UDMA/100
[ 413.404766] sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
[ 413.404771] sd 0:0:0:0: [sda] Sense Key : Aborted Command [current] [descriptor]
[ 413.404777] Descriptor sense data with sense descriptors (in hex):
[ 413.404780] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 413.404790] 00 00 00 00
[ 413.404794] sd 0:0:0:0: [sda] Add. Sense: No additional sense information
[ 413.404799] end_request: I/O error, dev sda, sector 0
[ 413.404805] Buffer I/O error on device sda, logical block 0
[ 413.404822] ata1: EH complete
[ 413.404953] sd 0:0:0:0: [sda] Write Protect is off
[ 413.404956] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 413.551909] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 413.551912] ata1.00: BMDMA2 stat 0x82d0009
[ 413.551918] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 413.551920] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 413.551923] ata1.00: status: { DRDY ERR }
[ 413.551926] ata1.00: error: { ABRT }
[ 413.576745] ata1.00: configured for UDMA/100
[ 413.576757] ata1: EH complete
[ 413.723821] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 413.723827] ata1.00: BMDMA2 stat 0x82d0009
[ 413.723835] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 413.723837] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 413.723840] ata1.00: status: { DRDY ERR }
[ 413.723843] ata1.00: error: { ABRT }
[ 413.744735] ata1.00: configured for UDMA/100
[ 413.744756] ata1: EH complete
[ 413.891812] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 413.891815] ata1.00: BMDMA2 stat 0x82d0009
[ 413.891821] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 413.891823] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 413.891826] ata1.00: status: { DRDY ERR }
[ 413.891829] ata1.00: error: { ABRT }
[ 413.912756] ata1.00: configured for UDMA/100
[ 413.912768] ata1: EH complete
[ 414.059807] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 414.059810] ata1.00: BMDMA2 stat 0x82d0009
[ 414.059816] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 414.059818] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 414.059821] ata1.00: status: { DRDY ERR }
[ 414.059824] ata1.00: error: { ABRT }
[ 414.080732] ata1.00: configured for UDMA/100
[ 414.080744] ata1: EH complete
[ 414.227732] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 414.227735] ata1.00: BMDMA2 stat 0x82d0009
[ 414.227741] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 414.227743] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 414.227746] ata1.00: status: { DRDY ERR }
[ 414.227749] ata1.00: error: { ABRT }
[ 414.248732] ata1.00: configured for UDMA/100
[ 414.248757] ata1: EH complete
[ 414.395830] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 414.395834] ata1.00: BMDMA2 stat 0x82d0009
[ 414.395842] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 414.395844] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 414.395848] ata1.00: status: { DRDY ERR }
[ 414.395850] ata1.00: error: { ABRT }
[ 414.416740] ata1.00: configured for UDMA/100
[ 414.416760] sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
[ 414.416764] sd 0:0:0:0: [sda] Sense Key : Aborted Command [current] [descriptor]
[ 414.416771] Descriptor sense data with sense descriptors (in hex):
[ 414.416773] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 414.416783] 00 00 00 00
[ 414.416787] sd 0:0:0:0: [sda] Add. Sense: No additional sense information
[ 414.416793] end_request: I/O error, dev sda, sector 0
[ 414.416799] Buffer I/O error on device sda, logical block 0
[ 414.416818] ata1: EH complete
[ 414.563952] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 414.563956] ata1.00: BMDMA2 stat 0x82d0009
[ 414.563963] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 414.563964] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 414.563968] ata1.00: status: { DRDY ERR }
[ 414.563970] ata1.00: error: { ABRT }
[ 414.588737] ata1.00: configured for UDMA/100
[ 414.588752] ata1: EH complete
[ 414.735830] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 414.735833] ata1.00: BMDMA2 stat 0x82d0009
[ 414.735839] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 414.735841] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 414.735844] ata1.00: status: { DRDY ERR }
[ 414.735847] ata1.00: error: { ABRT }
[ 414.756728] ata1.00: configured for UDMA/100
[ 414.756740] ata1: EH complete
[ 414.903745] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 414.903751] ata1.00: BMDMA2 stat 0x82d0009
[ 414.903759] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 414.903761] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 414.903765] ata1.00: status: { DRDY ERR }
[ 414.903767] ata1.00: error: { ABRT }
[ 414.924750] ata1.00: configured for UDMA/100
[ 414.924770] ata1: EH complete
[ 415.071854] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 415.071858] ata1.00: BMDMA2 stat 0x82d0009
[ 415.071864] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 415.071865] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 415.071869] ata1.00: status: { DRDY ERR }
[ 415.071871] ata1.00: error: { ABRT }
[ 415.092734] ata1.00: configured for UDMA/100
[ 415.092747] ata1: EH complete
[ 415.239739] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 415.239742] ata1.00: BMDMA2 stat 0x82d0009
[ 415.239748] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 415.239750] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 415.239753] ata1.00: status: { DRDY ERR }
[ 415.239756] ata1.00: error: { ABRT }
[ 415.260980] ata1.00: configured for UDMA/100
[ 415.260993] ata1: EH complete
[ 415.408068] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 415.408072] ata1.00: BMDMA2 stat 0x82d0009
[ 415.408078] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 415.408080] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 415.408084] ata1.00: status: { DRDY ERR }
[ 415.408086] ata1.00: error: { ABRT }
[ 415.432750] ata1.00: configured for UDMA/100
[ 415.432764] sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
[ 415.432769] sd 0:0:0:0: [sda] Sense Key : Aborted Command [current] [descriptor]
[ 415.432775] Descriptor sense data with sense descriptors (in hex):
[ 415.432778] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 415.432788] 00 00 00 00
[ 415.432792] sd 0:0:0:0: [sda] Add. Sense: No additional sense information
[ 415.432798] end_request: I/O error, dev sda, sector 0
[ 415.432803] Buffer I/O error on device sda, logical block 0
[ 415.432818] ata1: EH complete
[ 415.432947] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 415.579975] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 415.579981] ata1.00: BMDMA2 stat 0x82d0009
[ 415.579989] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 415.579991] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 415.579995] ata1.00: status: { DRDY ERR }
[ 415.579997] ata1.00: error: { ABRT }
[ 415.604749] ata1.00: configured for UDMA/100
[ 415.604770] ata1: EH complete
[ 415.751800] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 415.751803] ata1.00: BMDMA2 stat 0x82d0009
[ 415.751809] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 415.751811] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 415.751814] ata1.00: status: { DRDY ERR }
[ 415.751817] ata1.00: error: { ABRT }
[ 415.772732] ata1.00: configured for UDMA/100
[ 415.772745] ata1: EH complete
[ 415.919833] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 415.919836] ata1.00: BMDMA2 stat 0x82d0009
[ 415.919842] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 415.919844] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 415.919847] ata1.00: status: { DRDY ERR }
[ 415.919850] ata1.00: error: { ABRT }
[ 415.940756] ata1.00: configured for UDMA/100
[ 415.940768] ata1: EH complete
[ 416.087845] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 416.087851] ata1.00: BMDMA2 stat 0x82d0009
[ 416.087860] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 416.087861] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 416.087865] ata1.00: status: { DRDY ERR }
[ 416.087868] ata1.00: error: { ABRT }
[ 416.112755] ata1.00: configured for UDMA/100
[ 416.112777] ata1: EH complete
[ 416.259805] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 416.259808] ata1.00: BMDMA2 stat 0x82d0009
[ 416.259814] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 416.259816] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 416.259820] ata1.00: status: { DRDY ERR }
[ 416.259822] ata1.00: error: { ABRT }
[ 416.280729] ata1.00: configured for UDMA/100
[ 416.280741] ata1: EH complete
[ 416.427822] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 416.427826] ata1.00: BMDMA2 stat 0x82d0009
[ 416.427832] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 416.427833] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 416.427837] ata1.00: status: { DRDY ERR }
[ 416.427839] ata1.00: error: { ABRT }
[ 416.448731] ata1.00: configured for UDMA/100
[ 416.448750] sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
[ 416.448755] sd 0:0:0:0: [sda] Sense Key : Aborted Command [current] [descriptor]
[ 416.448761] Descriptor sense data with sense descriptors (in hex):
[ 416.448764] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 416.448774] 00 00 00 00
[ 416.448778] sd 0:0:0:0: [sda] Add. Sense: No additional sense information
[ 416.448783] end_request: I/O error, dev sda, sector 0
[ 416.448789] Buffer I/O error on device sda, logical block 0
[ 416.448809] ata1: EH complete
[ 416.595921] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 416.595925] ata1.00: BMDMA2 stat 0x82d0009
[ 416.595931] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 416.595932] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 416.595936] ata1.00: status: { DRDY ERR }
[ 416.595938] ata1.00: error: { ABRT }
[ 416.620755] ata1.00: configured for UDMA/100
[ 416.620768] ata1: EH complete
[ 416.767831] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 416.767836] ata1.00: BMDMA2 stat 0x82d0009
[ 416.767844] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 416.767846] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 416.767850] ata1.00: status: { DRDY ERR }
[ 416.767852] ata1.00: error: { ABRT }
[ 416.788737] ata1.00: configured for UDMA/100
[ 416.788757] ata1: EH complete
[ 416.935799] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 416.935802] ata1.00: BMDMA2 stat 0x82d0009
[ 416.935808] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 416.935810] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 416.935813] ata1.00: status: { DRDY ERR }
[ 416.935816] ata1.00: error: { ABRT }
[ 416.956732] ata1.00: configured for UDMA/100
[ 416.956743] ata1: EH complete
[ 417.103821] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 417.103825] ata1.00: BMDMA2 stat 0x82d0009
[ 417.103831] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 417.103833] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 417.103836] ata1.00: status: { DRDY ERR }
[ 417.103839] ata1.00: error: { ABRT }
[ 417.124748] ata1.00: configured for UDMA/100
[ 417.124761] ata1: EH complete
[ 417.271860] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 417.271865] ata1.00: BMDMA2 stat 0x82d0009
[ 417.271873] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 417.271875] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 417.271879] ata1.00: status: { DRDY ERR }
[ 417.271881] ata1.00: error: { ABRT }
[ 417.296742] ata1.00: configured for UDMA/100
[ 417.296759] ata1: EH complete
[ 417.443798] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 417.443801] ata1.00: BMDMA2 stat 0x82d0009
[ 417.443807] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 417.443809] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 417.443813] ata1.00: status: { DRDY ERR }
[ 417.443815] ata1.00: error: { ABRT }
[ 417.464732] ata1.00: configured for UDMA/100
[ 417.464747] sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
[ 417.464752] sd 0:0:0:0: [sda] Sense Key : Aborted Command [current] [descriptor]
[ 417.464758] Descriptor sense data with sense descriptors (in hex):
[ 417.464760] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 417.464770] 00 00 00 00
[ 417.464774] sd 0:0:0:0: [sda] Add. Sense: No additional sense information
[ 417.464780] end_request: I/O error, dev sda, sector 0
[ 417.464785] Buffer I/O error on device sda, logical block 0
[ 417.464800] ata1: EH complete
[ 417.465555] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors: (100 GB/93.1 GiB)
[ 417.465581] sd 0:0:0:0: [sda] Write Protect is off
[ 417.465584] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 417.465615] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 417.465651] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors: (100 GB/93.1 GiB)
[ 417.465668] sd 0:0:0:0: [sda] Write Protect is off
[ 417.465671] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 417.465890] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA


LSMOD
Module Size Used by
nls_iso8859_1 12032 1
vfat 18816 1
fat 58272 1 vfat
usb_storage 82880 1
binfmt_misc 16776 1
ppdev 15620 0
lp 17156 0
parport 42220 2 ppdev,lp
radeon 342816 2
drm 96296 3 radeon
bridge 56340 0
stp 10500 1 bridge
bnep 20224 2
input_polldev 11912 0
snd_hda_intel 435636 3
snd_pcm_oss 46336 0
snd_mixer_oss 22656 1 snd_pcm_oss
snd_pcm 82948 2 snd_hda_intel,snd_pcm_oss
arc4 9856 2
pcmcia 44748 0
snd_seq_dummy 10756 0
ecb 10752 2
snd_seq_oss 37760 0
snd_seq_midi 14336 0
joydev 18368 0
snd_rawmidi 29696 1 snd_seq_midi
snd_seq_midi_event 15104 2 snd_seq_oss,snd_seq_midi
ath5k 107008 0
snd_seq 56880 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_mid i_event
snd_timer 29704 2 snd_pcm,snd_seq
snd_seq_device 14988 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi ,snd_seq
mac80211 217208 1 ath5k
yenta_socket 32396 1
rsrc_nonstatic 19328 1 yenta_socket
led_class 12036 1 ath5k
ati_agp 14988 0
video 25360 0
snd 62628 15 snd_hda_intel,snd_pcm_oss,snd_mixer_oss,snd_pcm,sn d_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_de vice
psmouse 61972 0
pcmcia_core 43540 3 pcmcia,yenta_socket,rsrc_nonstatic
output 11008 1 video
soundcore 15200 1 snd
agpgart 42696 2 drm,ati_agp
shpchp 40212 0
serio_raw 13316 0
i2c_piix4 18448 0
pcspkr 10496 0
cfg80211 38032 2 ath5k,mac80211
snd_page_alloc 16904 2 snd_hda_intel,snd_pcm
usbhid 42336 0
squashfs 46344 1
aufs 165924 1
exportfs 12544 1 aufs
nls_cp437 13696 2
isofs 39844 1
8139too 32128 0
8139cp 27776 0
mii 13312 2 8139too,8139cp
fbcon 46112 0
tileblit 10752 1 fbcon
font 16384 1 fbcon
bitblit 13824 1 fbcon
softcursor 9984 1 bitblit