Hi,
I have a problem with my Linksys wireless USB device (wusb54g ver. 4)with ubuntu 8.04.
Below is my config results:
My AP Wireless Channel is set to 2.
Network tools output:
Network device: wlan0
Hardware address: 00:12:17:7d:0c:2b
IP address: 192.168.1.68
Netmask: 255.255.255.0
Broadcast: 192.168.1.255
Multicast: Enabled
MTU: 1500
Link speed: 5.5 Mbps
State: Active
Transmitted packets: 57
Transmission errors: 0
Received packets: 11
Reception errors: 0
Collisions: 0
Network device: wmaster0
Hardware address: not available
IP address: not available
Netmask: not available
Broadcast: not available
Multicast: not available
MTU: not available
Link speed: not available
State: not available
Transmitted packets: 0
Transmission errors: 0
Received packets: 0
Reception errors: 0
Collisions: 0
When I press configure error = “The interface doesn't exist”
HOME:~$ iwconfig
lo no wireless extensions.
eth1 no wireless extensions.
wmaster0 no wireless extensions.
wlan0 IEEE 802.11g ESSID:"2WIRE208"
Mode:Managed Frequency:2.417 GHz Access Point: 00:1B:5B:2A:31:41
Tx-Power=27 dBm
Retry min limit:7 RTS thrff Fragment thr=2346 B
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
HOME:~$ ifconfig wlan0
wlan0 Link encap:Ethernet HWaddr 00:12:17:7d:0c:2b
inet addr:192.168.1.68 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::212:17ff:fe7d:c2b/64 Scope:Link
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:11 errors:0 dropped:0 overruns:0 frame:0
TX packets:57 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1007 (1007.0 B) TX bytes:8302 (8.1 KB)
HOME:~$ sudo ifdown wmaster0
ifdown: interface wmaster0 not configured
HOME:~$ sudo ifup wlan0
ifup: interface wlan0 already configured
HOME:~$ lspci
00:00.0 Host bridge: Advanced Micro Devices [AMD] RS780 Host Bridge
00:01.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (int gfx)
00:06.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 2)
00:11.0 SATA controller: ATI Technologies Inc SB700/SB800 SATA Controller [IDE mode]
00:12.0 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller
00:12.1 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI1 Controller
00:12.2 USB Controller: ATI Technologies Inc SB700/SB800 USB EHCI Controller
00:13.0 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller
00:13.1 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI1 Controller
00:13.2 USB Controller: ATI Technologies Inc SB700/SB800 USB EHCI Controller
00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 3a)
00:14.1 IDE interface: ATI Technologies Inc SB700/SB800 IDE Controller
00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia
00:14.3 ISA bridge: ATI Technologies Inc SB700/SB800 LPC host controller
00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge
00:14.5 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI2 Controller
00:18.0 Host bridge: Advanced Micro Devices [AMD] Family 10h [Opteron, Athlon64, Sempron] HyperTransport Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] Family 10h [Opteron, Athlon64, Sempron] Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] Family 10h [Opteron, Athlon64, Sempron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] Family 10h [Opteron, Athlon64, Sempron] Miscellaneous Control
00:18.4 Host bridge: Advanced Micro Devices [AMD] Family 10h [Opteron, Athlon64, Sempron] Link Control
01:05.0 VGA compatible controller: ATI Technologies Inc Radeon HD 3200 Graphics
01:05.1 Audio device: ATI Technologies Inc RS780 Azalia controller
02:00.0 Ethernet controller: Attansic Technology Corp. L1 Gigabit Ethernet Adapter (rev b0)
Note: Looks like no device is listed but I am getting the correct info from my AP i.e. MAC Address. I also only have one wireless device and I don't know how to remove wmaster0
Bookmarks