Results 1 to 3 of 3

Thread: Ubuntu 8.08 won't start on Asus EEEPC (SD card)

  1. #1
    Join Date
    Apr 2007
    Location
    New Zealand
    Beans
    894
    Distro
    Ubuntu 9.10 Karmic Koala

    Ubuntu 8.08 won't start on Asus EEEPC (SD card)

    Hi there boys & girls. I am having difficulty with the following setup:

    Asus EEE PC, with Ubuntu 8.08 and GRUB installed on the SD card.

    What happens, is I throw in the SD card, boot from it with GRUB, and Ubuntu starts to load. It freezes on 'Initializing USB mass storage driver...' (I can see this because I am booting with Recovery Mode)

    If I leave it there for a good 2 or 3 minutes, it continues to the login prompt.

    After logging in, it freezes at a blank tan page. Nothing happens from that point on.
    I will paste my dmesg below, and bold things I think are of interest. Can anyone please provide help? This is a standard Ubuntu 8.08 going onto a 16GB SD Card in its cardreader:

    Code:
    [    0.000000] Linux version 2.6.24-16-generic (buildd@palmer) (gcc version 4.2.3 (Ubuntu 4.2.3-2ubuntu7)) #1 SMP Thu Apr 10 13:23:42 UTC 2008 (Ubuntu 2.6.24-16.30-generic)
    [    0.000000] BIOS-provided physical RAM map:
    [    0.000000]  BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
    [    0.000000]  BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
    [    0.000000]  BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
    [    0.000000]  BIOS-e820: 0000000000100000 - 000000001f780000 (usable)
    [    0.000000]  BIOS-e820: 000000001f780000 - 000000001f790000 (ACPI data)
    [    0.000000]  BIOS-e820: 000000001f790000 - 000000001f7d0000 (ACPI NVS)
    [    0.000000]  BIOS-e820: 000000001f7d0000 - 000000001f7de000 (reserved)
    [    0.000000]  BIOS-e820: 000000001f7e0000 - 000000001f800000 (reserved)
    [    0.000000]  BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
    [    0.000000]  BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
    [    0.000000] 0MB HIGHMEM available.
    [    0.000000] 503MB LOWMEM available.
    [    0.000000] found SMP MP-table at 000ff780
    [    0.000000] Entering add_active_range(0, 0, 128896) 0 entries of 256 used
    [    0.000000] Zone PFN ranges:
    [    0.000000]   DMA             0 ->     4096
    [    0.000000]   Normal       4096 ->   128896
    [    0.000000]   HighMem    128896 ->   128896
    [    0.000000] Movable zone start PFN for each node
    [    0.000000] early_node_map[1] active PFN ranges
    [    0.000000]     0:        0 ->   128896
    [    0.000000] On node 0 totalpages: 128896
    [    0.000000]   DMA zone: 32 pages used for memmap
    [    0.000000]   DMA zone: 0 pages reserved
    [    0.000000]   DMA zone: 4064 pages, LIFO batch:0
    [    0.000000]   Normal zone: 975 pages used for memmap
    [    0.000000]   Normal zone: 123825 pages, LIFO batch:31
    [    0.000000]   HighMem zone: 0 pages used for memmap
    [    0.000000]   Movable zone: 0 pages used for memmap
    [    0.000000] DMI present.
    [    0.000000] ACPI: RSDP signature @ 0xC00FBE60 checksum 0
    [    0.000000] ACPI: RSDP 000FBE60, 0014 (r0 ACPIAM)
    [    0.000000] ACPI: RSDT 1F780000, 0034 (r1 A M I  OEMRSDT   1000804 MSFT       97)
    [    0.000000] ACPI: FACP 1F780200, 0081 (r1 A M I  OEMFACP   1000804 MSFT       97)
    [    0.000000] ACPI: DSDT 1F780400, 5F2B (r1  A0797 A0797000        0 INTL 20051117)
    [    0.000000] ACPI: FACS 1F790000, 0040
    [    0.000000] ACPI: APIC 1F780390, 0068 (r1 A M I  OEMAPIC   1000804 MSFT       97)
    [    0.000000] ACPI: OEMB 1F790040, 0046 (r1 A M I  AMI_OEM   1000804 MSFT       97)
    [    0.000000] ACPI: MCFG 1F786330, 003C (r1 A M I  OEMMCFG   1000804 MSFT       97)
    [    0.000000] ACPI: PM-Timer IO Port: 0x808
    [    0.000000] ACPI: Local APIC address 0xfee00000
    [    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
    [    0.000000] Processor #0 6:13 APIC version 20
    [    0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
    [    0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
    [    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
    [    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
    [    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
    [    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
    [    0.000000] ACPI: IRQ0 used by override.
    [    0.000000] ACPI: IRQ2 used by override.
    [    0.000000] ACPI: IRQ9 used by override.
    [    0.000000] Enabling APIC mode:  Flat.  Using 1 I/O APICs
    [    0.000000] Using ACPI (MADT) for SMP configuration information
    [    0.000000] Allocating PCI resources starting at 20000000 (gap: 1f800000:df600000)
    [    0.000000] swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
    [    0.000000] swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000e4000
    [    0.000000] swsusp: Registered nosave memory region: 00000000000e4000 - 0000000000100000
    [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 127889
    [    0.000000] Kernel command line: root=UUID=c9cce3b4-615c-42b4-8a44-e5b86a0dbc6a ro single
    [    0.000000] mapped APIC to ffffb000 (fee00000)
    [    0.000000] mapped IOAPIC to ffffa000 (fec00000)
    [    0.000000] Enabling fast FPU save and restore... done.
    [    0.000000] Enabling unmasked SIMD FPU exception support... done.
    [    0.000000] Initializing CPU#0
    [    0.000000] PID hash table entries: 2048 (order: 11, 8192 bytes)
    [    0.000000] Detected 630.088 MHz processor.
    [   17.971184] Console: colour VGA+ 80x25
    [   17.971193] console [tty0] enabled
    [   17.975887] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
    [   17.976510] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
    [   18.003577] Memory: 498724k/515584k available (2157k kernel code, 16192k reserved, 998k data, 364k init, 0k highmem)
    [   18.003729] virtual kernel memory layout:
    [   18.003732]     fixmap  : 0xfff4b000 - 0xfffff000   ( 720 kB)
    [   18.003735]     pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
    [   18.003739]     vmalloc : 0xe0000000 - 0xff7fe000   ( 503 MB)
    [   18.003742]     lowmem  : 0xc0000000 - 0xdf780000   ( 503 MB)
    [   18.003745]       .init : 0xc041b000 - 0xc0476000   ( 364 kB)
    [   18.003749]       .data : 0xc031b5a4 - 0xc0414dc4   ( 998 kB)
    [   18.003752]       .text : 0xc0100000 - 0xc031b5a4   (2157 kB)
    [   18.004410] Checking if this processor honours the WP bit even in supervisor mode... Ok.
    [   18.004648] SLUB: Genslabs=11, HWalign=64, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
    [   18.084791] Calibrating delay using timer specific routine.. 1261.75 BogoMIPS (lpj=2523507)
    [   18.085006] Security Framework initialized
    [   18.085099] SELinux:  Disabled at boot.
    [   18.085212] AppArmor: AppArmor initialized
    [   18.085301] Failure registering capabilities with primary security module.
    [   18.085408] Mount-cache hash table entries: 512
    [   18.085782] CPU: After generic identify, caps: afe9fbbf 00000000 00000000 00000000 00000000 00000000 00000000 00000000
    [   18.085814] CPU: L1 I cache: 32K, L1 D cache: 32K
    [   18.085937] CPU: L2 cache: 512K
    [   18.086015] CPU: After all inits, caps: afe9fbbf 00000000 00000000 00002040 00000000 00000000 00000000 00000000
    [   18.086036] Compat vDSO mapped to ffffe000.
    [   18.086139] Checking 'hlt' instruction... OK.
    [   18.101763] SMP alternatives: switching to UP code
    [   18.106609] Freeing SMP alternatives: 11k freed
    [   18.106971] Early unpacking initramfs... done
    [   19.121567] ACPI: Core revision 20070126
    [   19.121828] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
    [   19.322866] CPU0: Intel(R) Celeron(R) M processor          900MHz stepping 06
    [   19.323070] Total of 1 processors activated (1261.75 BogoMIPS).
    [   19.323331] ENABLING IO-APIC IRQs
    [   19.323639] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
    [   19.468795] Brought up 1 CPUs
    [   19.468919] CPU0 attaching sched-domain:
    [   19.468926]  domain 0: span 01
    [   19.468931]   groups: 01
    [   19.469365] net_namespace: 64 bytes
    [   19.469468] Booting paravirtualized kernel on bare hardware
    [   19.470812] Time: 11:20:11  Date: 06/01/08
    [   19.470959] NET: Registered protocol family 16
    [   19.471581] EISA bus registered
    [   19.471696] ACPI: bus type pci registered
    [   19.472306] PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=5
    [   19.472403] PCI: Using configuration type 1
    [   19.472483] Setting up standard PCI resources
    [   19.495811] ACPI: EC: Look up EC in DSDT
    [   19.524928] ACPI: Interpreter enabled
    [   19.525019] ACPI: (supports S0 S1 S3 S4 S5)
    [   19.525299] ACPI: Using IOAPIC for interrupt routing
    [   19.542205] ACPI: EC: GPE = 0x18, I/O: command/status = 0x66, data = 0x62
    [   19.542305] ACPI: EC: driver started in poll mode
    [   19.542701] ACPI: PCI Root Bridge [PCI0] (0000:00)
    [   19.543818] Force enabled HPET at base address 0xfed00000
    [   19.543832] PCI quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO
    [   19.543926] PCI quirk: region 0480-04bf claimed by ICH6 GPIO
    [   19.544887] PCI: Transparent bridge - 0000:00:1e.0
    [   19.545037] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
    [   19.545454] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P3._PRT]
    [   19.545682] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P5._PRT]
    [   19.545900] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P6._PRT]
    [   19.557638] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 10 11 12 14 15)
    [   19.558462] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
    [   19.559265] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *10 11 12 14 15)
    [   19.560077] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 *7 10 11 12 14 15)
    [   19.560894] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
    [   19.561798] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
    [   19.562698] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
    [   19.563601] ACPI: PCI Interrupt Link [LNKH] (IRQs *3 4 5 6 7 10 11 12 14 15)
    [   19.564444] Linux Plug and Play Support v0.97 (c) Adam Belay
    [   19.564623] pnp: PnP ACPI init
    [   19.564746] ACPI: bus type pnp registered
    [   19.570073] pnp: PnP ACPI: found 13 devices
    [   19.570161] ACPI: ACPI bus type pnp unregistered
    [   19.570249] PnPBIOS: Disabled by ACPI PNP
    [   19.570980] PCI: Using ACPI for IRQ routing
    [   19.571071] PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
    [   19.592701] NET: Registered protocol family 8
    [   19.592786] NET: Registered protocol family 20
    [   19.593288] hpet clockevent registered
    [   19.593299] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
    [   19.593517] hpet0: 3 64-bit timers, 14318180 Hz
    [   19.594688] AppArmor: AppArmor Filesystem Enabled
    [   19.596679] Time: tsc clocksource has been installed.
    [   19.604788] system 00:01: iomem range 0xfed13000-0xfed19fff has been reserved
    [   19.604912] system 00:08: ioport range 0x380-0x383 has been reserved
    [   19.605006] system 00:08: ioport range 0x4d0-0x4d1 has been reserved
    [   19.605098] system 00:08: ioport range 0x800-0x87f has been reserved
    [   19.605189] system 00:08: ioport range 0x480-0x4bf has been reserved
    [   19.605282] system 00:08: iomem range 0xfed1c000-0xfed1ffff has been reserved
    [   19.605376] system 00:08: iomem range 0xfed20000-0xfed8ffff has been reserved
    [   19.605472] system 00:08: iomem range 0xfff00000-0xffffffff could not be reserved
    [   19.605603] system 00:09: iomem range 0xfec00000-0xfec00fff has been reserved
    [   19.605699] system 00:09: iomem range 0xfee00000-0xfee00fff could not be reserved
    [   19.605830] system 00:0a: iomem range 0xe0000000-0xefffffff has been reserved
    [   19.605932] system 00:0b: iomem range 0xe0000000-0xefffffff has been reserved
    [   19.606037] system 00:0c: iomem range 0x0-0x9ffff could not be reserved
    [   19.606129] system 00:0c: iomem range 0xc0000-0xcffff could not be reserved
    [   19.606223] system 00:0c: iomem range 0xe0000-0xfffff could not be reserved
    [   19.606318] system 00:0c: iomem range 0x100000-0x1f7fffff could not be reserved
    [   19.606441] system 00:0c: iomem range 0x0-0x0 could not be reserved
    [   19.637646] PCI: Bridge: 0000:00:1c.0
    [   19.637729]   IO window: disabled.
    [   19.637812]   MEM window: disabled.
    [   19.637891]   PREFETCH window: disabled.
    [   19.637977] PCI: Bridge: 0000:00:1c.1
    [   19.638053]   IO window: disabled.
    [   19.638134]   MEM window: fbf00000-fbffffff
    [   19.638217]   PREFETCH window: disabled.
    [   19.638300] PCI: Bridge: 0000:00:1c.2
    [   19.638377]   IO window: disabled.
    [   19.638458]   MEM window: f8000000-fbefffff
    [   19.638543]   PREFETCH window: f0000000-f6ffffff
    [   19.638630] PCI: Bridge: 0000:00:1e.0
    [   19.638707]   IO window: disabled.
    [   19.638787]   MEM window: disabled.
    [   19.638867]   PREFETCH window: disabled.
    [   19.638998] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
    [   19.639160] PCI: Setting latency timer of device 0000:00:1c.0 to 64
    [   19.639189] ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 17 (level, low) -> IRQ 17
    [   19.639349] PCI: Setting latency timer of device 0000:00:1c.1 to 64
    [   19.639378] ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) -> IRQ 18
    [   19.639537] PCI: Setting latency timer of device 0000:00:1c.2 to 64
    [   19.639555] PCI: Setting latency timer of device 0000:00:1e.0 to 64
    [   19.639591] NET: Registered protocol family 2
    [   19.676836] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
    [   19.677438] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
    [   19.677823] TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
    [   19.678175] TCP: Hash tables configured (established 16384 bind 16384)
    [   19.678267] TCP reno registered
    [   19.689011] checking if image is initramfs...<7>Switched to high resolution mode on CPU 0
    [   20.649169]  it is
    [   21.676813] Freeing initrd memory: 7648k freed
    [   21.678350] audit: initializing netlink socket (disabled)
    [   21.678470] audit(1212319212.364:1): initialized
    [   21.684091] VFS: Disk quotas dquot_6.5.1
    [   21.684409] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
    [   21.684886] io scheduler noop registered
    [   21.684970] io scheduler anticipatory registered
    [   21.685052] io scheduler deadline registered
    [   21.685172] io scheduler cfq registered (default)
    [   21.685279] Boot video device is 0000:00:02.0
    [   21.685658] PCI: Setting latency timer of device 0000:00:1c.0 to 64
    [   21.685722] assign_interrupt_mode Found MSI capability
    [   21.685865] Allocate Port Service[0000:00:1c.0:pcie00]
    [   21.685977] Allocate Port Service[0000:00:1c.0:pcie02]
    [   21.686149] PCI: Setting latency timer of device 0000:00:1c.1 to 64
    [   21.686210] assign_interrupt_mode Found MSI capability
    [   21.686343] Allocate Port Service[0000:00:1c.1:pcie00]
    [   21.686446] Allocate Port Service[0000:00:1c.1:pcie02]
    [   21.686617] PCI: Setting latency timer of device 0000:00:1c.2 to 64
    [   21.686677] assign_interrupt_mode Found MSI capability
    [   21.686808] Allocate Port Service[0000:00:1c.2:pcie00]
    [   21.686911] Allocate Port Service[0000:00:1c.2:pcie02]
    [   21.687588] isapnp: Scanning for PnP cards...
    [   22.041880] isapnp: No Plug & Play device found
    [   22.143674] Real Time Clock Driver v1.12ac
    [   22.144014] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
    [   22.147609] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
    [   22.147953] input: Macintosh mouse button emulation as /devices/virtual/input/input0
    [   22.148404] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
    [   22.180693] serio: i8042 KBD port at 0x60,0x64 irq 1
    [   22.180790] serio: i8042 AUX port at 0x60,0x64 irq 12
    [   22.192415] mice: PS/2 mouse device common for all mice
    [   22.192808] EISA: Probing bus 0 at eisa.0
    [   22.192935] EISA: Detected 0 cards.
    [   22.193015] cpuidle: using governor ladder
    [   22.193095] cpuidle: using governor menu
    [   22.193390] NET: Registered protocol family 1
    [   22.193533] Using IPI No-Shortcut mode
    [   22.193693] registered taskstats version 1
    [   22.193993]   Magic number: 12:509:326
    [   22.194113]   hash matches device ttyyf
    [   22.194391] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
    [   22.194481] EDD information not available.
    [   22.194929] Freeing unused kernel memory: 364k freed
    [   22.228287] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
    [   22.730323] fuse init (API version 7.9)
    [   22.797670] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
    [   22.797905] ACPI: Processor [CPU1] (supports 8 throttling states)
    [   22.802387] ACPI: EC: non-query interrupt received, switching to interrupt mode
    [   22.808027] ACPI: Thermal Zone [TZ00] (23 C)
    [   24.735962] usbcore: registered new interface driver usbfs
    [   24.736106] usbcore: registered new interface driver hub
    [   24.747933] usbcore: registered new device driver usb
    [   24.768426] USB Universal Host Controller Interface driver v3.0
    [   24.768666] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 19
    [   24.768838] PCI: Setting latency timer of device 0000:00:1d.0 to 64
    [   24.768848] uhci_hcd 0000:00:1d.0: UHCI Host Controller
    [   24.769598] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
    [   24.769771] uhci_hcd 0000:00:1d.0: irq 19, io base 0x0000e400
    [   24.770198] usb usb1: configuration #1 chosen from 1 choice
    [   24.770350] hub 1-0:1.0: USB hub found
    [   24.770440] hub 1-0:1.0: 2 ports detected
    [   24.872068] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 20
    [   24.872252] PCI: Setting latency timer of device 0000:00:1d.1 to 64
    [   24.872265] uhci_hcd 0000:00:1d.1: UHCI Host Controller
    [   24.872409] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
    [   24.872575] uhci_hcd 0000:00:1d.1: irq 20, io base 0x0000e480
    [   24.872945] usb usb2: configuration #1 chosen from 1 choice
    [   24.873089] hub 2-0:1.0: USB hub found
    [   24.873179] hub 2-0:1.0: 2 ports detected
    [   24.976034] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
    [   24.976221] PCI: Setting latency timer of device 0000:00:1d.2 to 64
    [   24.976231] uhci_hcd 0000:00:1d.2: UHCI Host Controller
    [   24.976374] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
    [   24.976538] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000e800
    [   24.976911] usb usb3: configuration #1 chosen from 1 choice
    [   24.977054] hub 3-0:1.0: USB hub found
    [   24.977146] hub 3-0:1.0: 2 ports detected
    [   25.080032] ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 16
    [   25.080225] PCI: Setting latency timer of device 0000:00:1d.3 to 64
    [   25.080235] uhci_hcd 0000:00:1d.3: UHCI Host Controller
    [   25.080402] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
    [   25.080568] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000e880
    [   25.080950] usb usb4: configuration #1 chosen from 1 choice
    [   25.081102] hub 4-0:1.0: USB hub found
    [   25.081191] hub 4-0:1.0: 2 ports detected
    [   25.172821] SCSI subsystem initialized
    [   25.194340] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 19
    [   25.194536] PCI: Setting latency timer of device 0000:00:1d.7 to 64
    [   25.194545] ehci_hcd 0000:00:1d.7: EHCI Host Controller
    [   25.194695] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
    [   25.198751] ehci_hcd 0000:00:1d.7: debug port 1
    [   25.198839] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
    [   25.198855] ehci_hcd 0000:00:1d.7: irq 19, io mem 0xf7eb7c00
    [   25.211762] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
    [   25.212187] usb usb5: configuration #1 chosen from 1 choice
    [   25.212334] hub 5-0:1.0: USB hub found
    [   25.212426] hub 5-0:1.0: 8 ports detected
    [   25.307769] libata version 3.00 loaded.
    [   25.344425] ahci 0000:00:1f.2: version 3.0
    [   25.344478] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 20
    [   25.344655] ACPI: PCI interrupt for device 0000:00:1f.2 disabled
    [   25.344752] ahci: probe of 0000:00:1f.2 failed with error -22
    [   25.460713] ata_piix 0000:00:1f.2: version 2.12
    [   25.460730] ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ]
    [   25.460990] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 20
    [   25.461217] PCI: Setting latency timer of device 0000:00:1f.2 to 64
    [   25.485003] scsi0 : ata_piix
    [   25.519711] scsi1 : ata_piix
    [   25.523213] ata1: SATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
    [   25.523310] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
    [   25.591731] usb 5-5: new high speed USB device using ehci_hcd and address 2
    [   25.725295] usb 5-5: configuration #1 chosen from 1 choice
    [   25.848090] ata2.00: ATA-4: SILICONMOTION SM223AC, , max UDMA/66
    [   25.848195] ata2.00: 7815024 sectors, multi 0: LBA 
    [   25.848315] ata2.00: limited to UDMA/33 due to 40-wire cable
    [   25.864056] ata2.00: configured for UDMA/33
    [   25.864494] scsi 1:0:0:0: Direct-Access     ATA      SILICONMOTION SM n/a  PQ: 0 ANSI: 5
    [   26.839591] Driver 'sd' needs updating - please use bus_type methods
    [   26.839891] sd 1:0:0:0: [sda] 7815024 512-byte hardware sectors (4001 MB)
    [   26.840009] sd 1:0:0:0: [sda] Write Protect is off
    [   26.840095] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
    [   26.840139] sd 1:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
    [   26.840381] sd 1:0:0:0: [sda] 7815024 512-byte hardware sectors (4001 MB)
    [   26.840495] sd 1:0:0:0: [sda] Write Protect is off
    [   26.840580] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
    [   26.840621] sd 1:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
    [   26.840754]  sda: sda1 sda2 sda3 sda4
    [   26.842086] sd 1:0:0:0: [sda] Attached SCSI disk
    [   26.859656] sd 1:0:0:0: Attached scsi generic sg0 type 0
    [   26.884943] usbcore: registered new interface driver libusual
    [   26.897986] Initializing USB Mass Storage driver...
    [   26.906002] scsi2 : SCSI emulation for USB Mass Storage devices
    [   26.912135] usbcore: registered new interface driver usb-storage
    [   26.912240] USB Mass Storage support registered.
    [   26.912538] usb-storage: device found at 2
    [   26.912544] usb-storage: waiting for device to settle before scanning
    [   27.091434] Clocksource tsc unstable (delta = -70191854508 ns)
    [   27.095423] Time: hpet clocksource has been installed.
    [   27.186458] usb-storage: device scan complete
    [   27.186934] scsi 2:0:0:0: Direct-Access     USB2.0   CardReader SD0   0100 PQ: 0 ANSI: 0
    [   27.430592] sd 2:0:0:0: [sdb] 31388672 512-byte hardware sectors (16071 MB)
    [   27.431088] sd 2:0:0:0: [sdb] Write Protect is off
    [   27.431178] sd 2:0:0:0: [sdb] Mode Sense: 03 00 00 00
    [   27.431190] sd 2:0:0:0: [sdb] Assuming drive cache: write through
    [   27.432837] sd 2:0:0:0: [sdb] 31388672 512-byte hardware sectors (16071 MB)
    [   27.433323] sd 2:0:0:0: [sdb] Write Protect is off
    [   27.433410] sd 2:0:0:0: [sdb] Mode Sense: 03 00 00 00
    [   27.433421] sd 2:0:0:0: [sdb] Assuming drive cache: write through
    [   27.433513]  sdb: sdb1 sdb2
    [   27.434914] sd 2:0:0:0: [sdb] Attached SCSI removable disk
    [   27.435106] sd 2:0:0:0: Attached scsi generic sg1 type 0
    [   27.617841] Attempting manual resume
    [   27.617925] swsusp: Resume From Partition 8:18
    [   27.617930] PM: Checking swsusp image.
    [   27.618807] PM: Resume from disk failed.
    [   36.127137] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
    [   36.192086] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
    [   36.376439] Linux agpgart interface v0.102
    [   36.433648] agpgart: Detected an Intel 915GM Chipset.
    [   36.434137] agpgart: Detected 7932K stolen memory.
    [   36.690949] iTCO_vendor_support: vendor-support=0
    [   36.752235] agpgart: AGP aperture is 256M @ 0xd0000000
    [   36.752478] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.02 (26-Jul-2007)
    [   36.752799] iTCO_wdt: Found a ICH6-M TCO device (Version=2, TCOBASE=0x0860)
    [   36.752988] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
    [   37.770716] intel_rng: FWH not detected
    [   38.582943] input: Power Button (FF) as /devices/virtual/input/input2
    [   38.598072] ACPI: Power Button (FF) [PWRF]
    [   38.598466] input: Lid Switch as /devices/virtual/input/input3
    [   38.605634] ACPI: Lid Switch [LID]
    [   38.605945] input: Sleep Button (CM) as /devices/virtual/input/input4
    [   38.618540] ACPI: Sleep Button (CM) [SLPB]
    [   38.618913] input: Power Button (CM) as /devices/virtual/input/input5
    [   38.630524] ACPI: Power Button (CM) [PWRB]
    [   41.459410] ACPI: AC Adapter [AC0] (off-line)
    [   41.591034] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input6
    [   41.601929] ACPI: Video Device [VGA] (multi-head: yes  rom: no  post: no)
    [   44.005503] Attansic(R) L2 Ethernet Network Driver - version 1.0.40.2
    [   44.005610] Copyright (c) 2006 Attansic Corporation.
    [   44.006891] ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 17 (level, low) -> IRQ 17
    [   44.007077] PCI: Setting latency timer of device 0000:03:00.0 to 64
    [   44.112820] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 16
    [   44.113040] PCI: Setting latency timer of device 0000:00:1b.0 to 64
    [   44.204886] ACPI: Battery Slot [BAT0] (battery present)
    [   45.105594] input: PC Speaker as /devices/platform/pcspkr/input/input7
    [   48.102777] Synaptics Touchpad, model: 1, fw: 6.3, id: 0x180b1, caps: 0xa04753/0x200000
    [   48.187898] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input8
    [   52.171978] lp: driver loaded but no devices found
    [   52.667235] Adding 144576k swap on /dev/sdb2.  Priority:-1 extents:1 across:144576k
    [   52.760721] EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
    [   53.794087] ip_tables: (C) 2000-2006 Netfilter Core Team
    [   55.123172] No dock devices found.
    [   57.431537] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
    [   57.431550] apm: overridden by ACPI.
    [   57.629720] ppdev: user-space parallel port driver
    [   57.681975] audit(1212319332.426:2): type=1503 operation="inode_permission" requested_mask="a::" denied_mask="a::" name="/dev/tty" pid=5306 profile="/usr/sbin/cupsd" namespace="default"
    [   59.309744] Bluetooth: Core ver 2.11
    [   59.314201] NET: Registered protocol family 31
    [   59.314212] Bluetooth: HCI device and connection manager initialized
    [   59.314225] Bluetooth: HCI socket layer initialized
    [   59.393054] Bluetooth: L2CAP ver 2.9
    [   59.393065] Bluetooth: L2CAP socket layer initialized
    [   59.541631] Bluetooth: RFCOMM socket layer initialized
    [   59.542652] Bluetooth: RFCOMM TTY layer initialized
    [   59.542664] Bluetooth: RFCOMM ver 1.8
    [   62.535615] [drm] Initialized drm 1.1.0 20060810
    [   62.546363] ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 16
    [   62.546385] PCI: Setting latency timer of device 0000:00:02.0 to 64
    [   62.548791] [drm] Initialized i915 1.6.0 20060119 on minor 0
    [   68.892844] gnome-keyring-d[5836]: segfault at 00000014 eip 080759c7 esp bffe2e00 error 6
    [   70.263854] gnome-keyring-d[5942]: segfault at 00000014 eip 080759c7 esp b7a36dc0 error 6
    [   70.898394] NET: Registered protocol family 10
    [   70.899837] lo: Disabled Privacy Extensions
    [   70.901540] ADDRCONF(NETDEV_UP): eth0: link is not ready
    Brown doesn't suck. And neither does wood. Download Woody. A Metacity theme.
    Note: the rm command deletes stuff! Don't be tricked into running malicious scripts. If in doubt, ask!!

  2. #2
    Join Date
    Apr 2007
    Location
    New Zealand
    Beans
    894
    Distro
    Ubuntu 9.10 Karmic Koala

    Re: Ubuntu 8.08 won't start on Asus EEEPC (SD card)

    Bump!
    Brown doesn't suck. And neither does wood. Download Woody. A Metacity theme.
    Note: the rm command deletes stuff! Don't be tricked into running malicious scripts. If in doubt, ask!!

  3. #3
    Join Date
    Oct 2007
    Location
    Chennai, India
    Beans
    3,798
    Distro
    Ubuntu Development Release

    Re: Ubuntu 8.08 won't start on Asus EEEPC (SD card)

    Quote Originally Posted by weblordpepe View Post
    Asus EEE PC, with Ubuntu 8.08 and GRUB installed on the SD card.

    [code][ 27.617925] swsusp: Resume From Partition 8:18
    [ 27.617930] PM: Checking swsusp image.
    [ 27.618807] PM: Resume from disk failed.[/B]

    [ 68.892844] gnome-keyring-d[5836]: segfault at 00000014 eip 080759c7 esp bffe2e00 error 6
    [ 70.263854] gnome-keyring-d[5942]: segfault at 00000014 eip 080759c7 esp b7a36dc0 error 6
    Known bug.. see https://bugs.launchpad.net/ubuntu/+s...ng/+bug/218434 for details and fix (Comment #58 by nyamap) (slightly convoluted, but easy for someone whose played around with the recovery console!).
    Cheers,PRShah
    Make your own: Ubuntu, Kubuntu, Xubuntu, Mythbuntu All-in-One Live DVD
    "I never make mistakes; I thought I did, once.. but I was wrong."

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •