Problems with Epson 4490 scanner after upgrade to 7.10

[rziegler72]

Still having issues with my Epson 4490, after upgrading from 7.04 to 7.10. It worked fine in 7.04.

I've installed the libsane-extras and sane-utils packages.

sane-find-scanner shows:
found USB scanner (vendor=0x04b8 [EPSON], product=0x0119 [EPSON Scanner]) at libusb:003:002

I added this to /etc/udev/rules.d/45-libsane.rules :
SYSFS{idVendor}=="04b8", SYSFS{idProduct}=="0119", MODE="664", GROUP="scanner"

I added this to /etc/sane.d/epson.conf :
usb 0×04b8 0x0119

Rebooted. Still no go. Any ideas or other info I can provide?

Thanks,
~Rick

[lampilux]

I had the same problem with a "4490 photo" model and I have removed the old driver and reinstall it in order to let the scanner working.

For installation instructions I follow a VERY GOOD post of Ron Morse that I cutted below because with google i didn't find it again on the web (i have saved it on my computer).

I hope for you it will work even with your model.

Good luck!

Tony

p.s.

(Sorry for my english... i'm italian)

CUT
On Saturday 17 March 2007 20:12:44 Denis Gaulin wrote:
> My problem is .. I have an EPSON scanner, 4490 perfection 4490 PHOTO that
> I use with my Mac IBOOK G4 and I want to switch to these new OS and I do
> not know how to install it on these computers because Kubuntu or UBUNTU do
> not recognize the scanner.
> The Kubuntu Documentation is silent about scanner package.... nothing in
> the official Documentation.

This is you lucky day. I just bought one of those units and worked out how to
get it working on Kubuntu Edgy (also works for Feisty).

The usual source for Linux scanner help and support is the SANE project at

http://www.sane-project.org/

Unfortunately, the Perfection 4490 Photo is not directly supported by SANE.
The good news is that Epkowa, the parent company for Epson in Japan, does
provide a Linux driver and a limited control software application for this
unit.

step 1. From the Ubuntu repositories for your version, Install sane and
related packages (libsane, libsane-extras, sane, sane-utils, xsane,
xsane-common, quiteinsane) All of these may not be strictly required, but I
do not know which ones are and which are not. That is just a list of what I
have installed.

step 2. Connect and power up the scanner. Wait 60 seconds for the scanner to
warm up -- this seems to be important as it won't report it's presence until
it is ready.

step3. make sure the scanner is detected. In a terminal window run:

sane-find-scanner

it should report :

found USB scanner (vendor=0x04b8 [EPSON], product=0x0119 [EPSON Scanner])
at libusb:001:006

or, run (also from a terminal window)

scanimage -L

and it should report finding an Epson Perfection 4490 flatbed scanner

The libsub address will probably be different depending on which port you have
connected the scanner. If sane-find-scanner or scanimage -L do not find a
scanner at all, stop. You have to solve that problem first.

step 4. Get the 4490 linux package from the Epkowa site:

http://www.avasys.jp/english/linux_e/dl_scan.html

Answer their questionnaire. Select Perfection 4490 Photo. I told them I was
using Debian and selected "other" in the version dialog. Clicking on
the "next" button will take you to a download page

step 5. The source code tarball will not build on Edgy or Feisty, so take the
two .rpm files (you need both the iScan and the driver package) from the
appropriate GCC version section for your distro. For Edgy or Feisty the GCC
3.4 files work.

step 6. If you haven't already done so, install alien from repository to
convert the .rpm files to .deb. (sudo apt-get install alien).

step 7. Convert the .rpm files. In a terminal window change to the directory
where the two downloaded driver files are located then:

sudo alien iscan_2.5.0-0.c2.i386.rpm
sudo alien iscan-plugin-gt-x750_1.0.0-1.c2.i386.rpm

This should produce the two .deb packages:

iscan_2.5.0-0.c2.i386.deb
iscan-plugin-gt-x750_1.0.0-1.c2.i386.deb

Ignore any errors that you may see here.

step 8. Install the two .deb packages from a terminal window with dpkg, doing
the main iscan package first.

sudo dpkg i- scan_2.5.0-0.c2.i386.deb
sudo dpkg -i iscan-plugin-gt-x750_1.0.0-1c2.i386.deb

Step 8a.

If the main iscan package will not install cleanly because it reports file
conflicts with certain sane-related packages previously installed, just go
ahead and force dpkg to overwrite

sudo dpkg i- --force-overwrite iscan_2.5.0-0.c2.i386.deb

The plugin should not have a conflict.

This completes the installation. To test things out make sure the scanner is
powered up and connected and then type

iscan

from a terminal, It should start and identify the scanner. Note the 4490
takes awhile to warm up, so don't do thing too quickly and don't be surprised
if things just sit there for a few moments before anything starts to happen.

Once iscan is installed, the xsane and quiteinsane front-ends also should find
and control the scanner. I prefer iScan to quiteinsane, but you can try them
all and decide what best meets your needs.

Ron Morse
END CUT

[rbmorse]

I updated my original post to correct a few details:

The usual source for Linux scanner help and support is the SANE project
at

http://www.sane-project.org/

Unfortunately, the Perfection 4490 Photo is not directly supported by
SANE. The good news is that Epkowa, the parent company for Epson in
Japan, provides a Linux driver and a limited control software
application for this unit. Both are available for no charge.

step 1. From the Ubuntu repositories for your version, Install sane and
related packages

sane
libsane
libsane-extras <--- required!
sane-utils
xsane (optional)
xsane-common (required for xsane)

step 2. Connect and power up the scanner. Wait 60 seconds for the
scanner to warm up.

step 3. make sure the scanner is detected. In a terminal window run:

sane-find-scanner

it should report :

found USB scanner vendor=0x04b8, product=0x0119 at libusb:001:006

The libsub address will vary depending upon which port the scanner is
connected. Ignore the suggestion to run scanimage -L as that will not
work until the scanner driver is installed (below).

If sane-find-scanner does not find a scanner at all, stop. You have to
solve that problem first.

step 4. Get the Perfection 4490 Photo Linux driver from the Epkowa
site:

http://www.avasys.jp/english/linux_e/dl_scan.html

Answer their questionnaire. Select Perfection 4490 Photo. I told them I
was using Debian and selected "other" in the version dialog. Clicking on
the "next" button will take you to a download page

step 5. The source code tarball will not build on Ubuntu(?) so take the
two .rpm files from the appropriate GCC version section for your distro.
For Edgy or Feisty the GCC 3.4 files work. The driver is required, but
iScan is a nice front end for the 4490.

step 6. If you haven't already done so, install

alien

from repository to convert the .rpm files to .deb. (sudo apt-get install
alien)

step 7. Convert the .rpm files. In a terminal window change to the
directory where the two downloaded driver files are located then:

sudo alien iscan_2.5.0-0.c2.i386.rpm
sudo alien iscan-plugin-gt-x750_1.0.0-1.c2.i386.rpm

This should produce the two .deb packages:

iscan_2.5.0-1_i386.deb
iscan-plugin-gt-x750_1.0.0-2_i386.deb

Ignore any errors that may show while alien is doing its thing.

step 8. Install the two .deb packages from a terminal window with dpkg.

sudo dpkg -i iscan-plugin-gt-x750_1.0.0-2_i386.deb
(optional, but recommended) sudo dpkg -i iscan_2.5.0-1_i386.deb

If the main iscan package will not install cleanly because it reports
file conflicts with certain sane-related packages previously installed,
just go ahead and force dpkg to overwrite

sudo dpkg -i --force-overwrite iscan_2.5.0-1_i386.deb

The plugin should not have a conflict.

This completes the installation. To test things out make sure the
scanner is powered up and connected and then type

sudo scanimage -L

from a terminal, It should start and identify the scanner. Note the
4490 takes awhile to warm up, so don't do thing too quickly and don't be
surprised if things just sit there for a few moments before anything
starts to happen.

Use

sudo iscan (if installed)

to test. Otherwise, you can test with xsane by typing

xsane

[crgutierrez]

GRACIAS Ron Morse!! Works also for Epson V350 Photo (while I was going insane why it didn't work after the upgrade from 7.04 to 7.10 and was about to pay somebody $40 for Vuescan......

[moschops]

Awesome - this worked with my Epson 3490 too - it was working with Feisty but stopped after a Gutsy upgrade, after 6 months I'd forgotten how I got it working in the first place so I'm glad I found this topic.

[kellner]

thanks for the detailed description! I never got the epson 4490 to work with 7.04, but following these instructions it now works just fine.

[Tux Aubrey]

Thanks for this how-to.

I just spent hours making it NOT work by downloading the wrong driver rpm! (the one for the 4990 instead of the 4490). How's that for stupidity?!

Anyway, as soon as I got the right one, everything worked. Saved me from booting Windows! Thank you!

[tquerette]

Did work with my epson CX4900. No need to download the Avasys driver witch does not compile under Gibbon/64bits.!!

Thanx

[luca.mg]

try http://ubuntuforums.org/showthread.p...26#post4389626

ciao luca

[Rollerbob]

Does anyone know if rbmores's howto will work on an AMD64 machine? Also, I'd be interested to know if anyone's got this working for the Epson V750 scanner, which is the upgrade to the 4990.