Code:
user@user-desktop:~$ sudo smartctl -a /dev/sda
smartctl 5.41 2011-06-09 r3365 [i686-linux-3.8.0-42-generic] (local build)
Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Model Family: Seagate DB35.3
Device Model: ST3320820SCE
Serial Number: 9QFBYZN3
Firmware Version: 3.ACE
User Capacity: 320,072,933,376 bytes [320 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: 7
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Sun Jun 22 12:36:22 2014 NZST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
See vendor-specific Attribute list for marginal Attributes.
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (15556) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 115) minutes.
SCT capabilities: (0x0031) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 103 097 006 Pre-fail Always - 5555400
3 Spin_Up_Time 0x0003 095 094 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 099 099 020 Old_age Always - 1187
5 Reallocated_Sector_Ct 0x0033 099 099 036 Pre-fail Always - 56
7 Seek_Error_Rate 0x000f 088 060 030 Pre-fail Always - 714385960
9 Power_On_Hours 0x0032 060 060 000 Old_age Always - 35405
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 108
187 Reported_Uncorrect 0x0032 001 001 000 Old_age Always - 60448
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 062 045 045 Old_age Always In_the_past 38 (Min/Max 23/38)
194 Temperature_Celsius 0x0022 038 055 000 Old_age Always - 38 (0 14 0 0)
195 Hardware_ECC_Recovered 0x001a 070 042 000 Old_age Always - 151797062
197 Current_Pending_Sector 0x0012 099 001 000 Old_age Always - 21
198 Offline_Uncorrectable 0x0010 099 001 000 Old_age Offline - 21
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0
202 Data_Address_Mark_Errs 0x0032 097 250 000 Old_age Always - 3
SMART Error Log Version: 1
ATA Error Count: 61264 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 61264 occurred at disk power-on lifetime: 35405 hours (1475 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 e3 ea 1d e1 Error: UNC at LBA = 0x011deae3 = 18737891
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 e0 ea 1d e1 00 01:48:20.414 READ DMA
b0 d5 01 00 4f c2 00 00 01:48:20.406 SMART READ LOG
27 00 00 00 00 00 e0 00 01:48:19.771 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 02 01:48:19.730 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 02 01:48:19.661 SET FEATURES [Set transfer mode]
Error 61263 occurred at disk power-on lifetime: 35405 hours (1475 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 e3 ea 1d e1 Error: UNC at LBA = 0x011deae3 = 18737891
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 e0 ea 1d e1 00 01:48:18.771 READ DMA
b0 da 00 00 4f c2 00 00 01:48:18.136 SMART RETURN STATUS
27 00 00 00 00 00 e0 00 01:48:19.771 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 02 01:48:19.730 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 02 01:48:19.661 SET FEATURES [Set transfer mode]
Error 61262 occurred at disk power-on lifetime: 35405 hours (1475 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 e3 ea 1d e1 Error: UNC at LBA = 0x011deae3 = 18737891
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 e0 ea 1d e1 00 01:48:18.771 READ DMA
b0 d1 01 01 4f c2 00 00 01:48:18.136 SMART READ ATTRIBUTE THRESHOLDS [OBS-4]
27 00 00 00 00 00 e0 00 01:48:18.007 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 02 01:48:18.004 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 02 01:48:18.003 SET FEATURES [Set transfer mode]
Error 61261 occurred at disk power-on lifetime: 35405 hours (1475 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 e3 ea 1d e1 Error: UNC at LBA = 0x011deae3 = 18737891
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 e0 ea 1d e1 00 01:48:17.116 READ DMA
b0 d0 01 00 4f c2 00 00 01:48:18.136 SMART READ DATA
35 00 e0 60 42 04 e0 00 01:48:18.007 WRITE DMA EXT
ca 00 08 b8 0a 04 e4 00 01:48:18.004 WRITE DMA
ca 00 08 50 0a 04 e4 00 01:48:18.003 WRITE DMA
Error 61260 occurred at disk power-on lifetime: 35405 hours (1475 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 e3 ea 1d e1 Error: UNC at LBA = 0x011deae3 = 18737891
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 e0 ea 1d e1 00 01:48:17.116 READ DMA
ec 00 01 00 00 00 00 00 01:48:17.101 IDENTIFY DEVICE
ca 00 08 90 fb 25 e2 00 01:48:17.085 WRITE DMA
27 00 00 00 00 00 e0 00 01:48:17.032 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 02 01:48:17.027 IDENTIFY DEVICE
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short captive Completed without error 00% 30489 -
# 2 Short captive Completed without error 00% 30489 -
# 3 Short offline Completed without error 00% 30174 -
# 4 Short offline Completed without error 00% 29616 -
# 5 Short offline Completed without error 00% 28025 -
# 6 Short offline Completed without error 00% 27399 -
# 7 Short offline Completed without error 00% 26672 -
# 8 Short offline Completed without error 00% 24473 -
# 9 Short offline Completed without error 00% 24352 -
#10 Short offline Completed without error 00% 23178 -
#11 Short offline Completed without error 00% 22619 -
#12 Short offline Completed without error 00% 22042 -
#13 Short offline Completed without error 00% 21025 -
#14 Short offline Completed without error 00% 20515 -
#15 Short offline Completed without error 00% 20010 -
#16 Short offline Completed without error 00% 18411 -
#17 Short offline Completed without error 00% 17784 -
#18 Short offline Aborted by host 90% 17651 -
#19 Short offline Aborted by host 90% 17416 -
#20 Short offline Completed without error 00% 15830 -
#21 Short offline Completed without error 00% 15267 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
user@user-desktop:~$
5 Cups of Ubuntu
Posting Permissions
Adv Reply
Bookmarks