View Poll Results: Has this thread been helpful?

Voters
811. You may not vote on this poll
  • Yes

    550 67.82%
  • No

    104 12.82%
  • Somewhat

    157 19.36%
Page 184 of 184 FirstFirst ... 84134174182183184
Results 1,831 to 1,832 of 1832

Thread: HOWTO: Wireless Security - WPA1, WPA2, LEAP, etc.

  1. #1831
    Join Date
    Aug 2013
    Beans
    1

    Re: HOWTO: Wireless Security - WPA1, WPA2, LEAP, etc.

    Hey,

    Not to bring an old thread back to life, but just wanted to say thanks to wieman01 & the many others in this thread. After much hair pulling, I'm up and running in Ubuntu 13.04 using WPA2!

    One question though - I've only updated the /etc/network/interfaces file, and when I boot up, wireless is automatically connected (not complaining ). Throughout the thread I've seen mentions to a configuration in order to have the wireless connect at boot. Is there something that has changed over the releases to make this automatically happen, or have I done something unknowingly to make this happen?

    Should anyone be interested, I've included my configurations below. Note: I uninstalled network manager after struggling for many days. I found that I wasn't finding my network name in the iwlist scan results. Once I removed network manager, my network name popped up. No idea if it is relevant, but just thought I'd throw it out there. I also tried running the 'wpa_supplicant -Dwext -iwlan0 -c/etc/wpa_supplicant.conf -dd' command with no success. Would be interested if anyone could fill me in on why this command doesn't work, but simply configuring the /etc/network/interfaces file does.


    # lspci -nnvv

    Code:
    02:0a.0 Network controller [0280]: Atheros Communications Inc. AR922X Wireless Network Adapter [168c:0029] (rev 01)
        Subsystem: D-Link System Inc DWA-552 802.11n Xtreme N Desktop Adapter (rev A2) [1186:3a7a]
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 168, Cache Line Size: 64 bytes
        Interrupt: pin A routed to IRQ 18
        Region 0: Memory at cfee0000 (32-bit, non-prefetchable) [size=64K]
        Capabilities: [44] Power Management version 2
            Flags: PMEClk- DSI- D1- D2- AuxCurrent=100mA PME(D0+,D1-,D2-,D3hot+,D3cold-)
            Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
        Kernel driver in use: ath9k

    # lshw -C network

    Code:
     *-network       description: Wireless interface
           product: AR922X Wireless Network Adapter
           vendor: Atheros Communications Inc.
           physical id: a
           bus info: pci@0000:02:0a.0
           logical name: wlan0
           version: 01
           serial: 00:18:e7:d5:b5:6e
           width: 32 bits
           clock: 66MHz
           capabilities: bus_master cap_list ethernet physical wireless
           configuration: broadcast=yes driver=ath9k driverversion=3.8.0-29-generic firmware=N/A ip=192.168.0.50 latency=168 link=yes multicast=yes wireless=IEEE 802.11bgn
           resources: irq:18 memory:cfee0000-cfeeffff

    # /etc/network/interfaces

    Code:
    # This file describes the network interfaces available on your system
    # and how to activate them. For more information, see interfaces(5).
    
    
    # The loopback network interface
    auto lo
    iface lo inet loopback
    
    
    auto wlan0
    iface wlan0 inet static
    address 192.168.0.50
    gateway 192.168.0.1
    dns-nameservers 8.8.8.8 192.168.0.1
    netmask 255.255.255.0
    wpa-driver wext
    wpa-ssid office
    wpa-ap-scan 1
    wpa-proto RSN
    wpa-pairwise CCMP
    wpa-group CCMP
    wpa-key-mgmt WPA-PSK
    wpa-psk 648376b573d37212568631ca58cedfb5f9d6027e268131e5de4cb90d166ab76b
    Cheers!

  2. #1832
    Join Date
    May 2006
    Location
    100acrewood
    Beans
    7,480
    Distro
    Kubuntu 14.04 Trusty Tahr

    Re: HOWTO: Wireless Security - WPA1, WPA2, LEAP, etc.

    Thank you for the feedback, AvocadoRed! I am thrilled to see this still works after so many years.

    Perhaps something has changed over the years in terms of wireless connection at boot, I am not entirely sure. But I noticed this as well, I no longer need the scripts mentioned in post 2.

    And thanks for posting the contents of your configuration files for reference!

Page 184 of 184 FirstFirst ... 84134174182183184

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •