View Poll Results: Has this thread been helpful?

Voters
811. You may not vote on this poll
  • Yes

    550 67.82%
  • No

    104 12.82%
  • Somewhat

    157 19.36%
Page 174 of 184 FirstFirst ... 74124164172173174175176 ... LastLast
Results 1,731 to 1,740 of 1832

Thread: HOWTO: Wireless Security - WPA1, WPA2, LEAP, etc.

  1. #1731
    Join Date
    May 2006
    Location
    100acrewood
    Beans
    7,480
    Distro
    Kubuntu 14.04 Trusty Tahr

    Re: HOWTO: Wireless Security - WPA1, WPA2, LEAP, etc.

    Please post every output that results from running the stuff that's posted under section "Post this if you are stumped". We'll go from there.

  2. #1732
    Join Date
    May 2009
    Beans
    12

    Re: HOWTO: Wireless Security - WPA1, WPA2, LEAP, etc.

    Quote Originally Posted by wieman01 View Post
    Please post every output that results from running the stuff that's posted under section "Post this if you are stumped". We'll go from there.

    Here is what I came up with up to the last two items:


    craig@craig-laptop:~$ route
    Kernel IP routing table
    Destination Gateway Genmask Flags Metric Ref Use Iface
    192.168.2.0 * 255.255.255.0 U 2 0 0 wlan0
    link-local * 255.255.0.0 U 1000 0 0 wlan0
    default 192.168.2.1 0.0.0.0 UG 0 0 0 wlan0
    craig@craig-laptop:~$ iwconfig
    lo no wireless extensions.

    eth0 no wireless extensions.

    eth1 IEEE 802.11b ESSID:"2WIRE684" Nickname:"Prism I"
    Mode:Managed Frequency:2.422 GHz Access Point: 00:1B:5B:65:43:51
    Bit Rate:11 Mb/s Sensitivity:1/3
    Retry short limit:8 RTS thr:off Fragment thr:off
    Power Management:off
    Link Quality=24/92 Signal level=-87 dBm Noise level=-141 dBm
    Rx invalid nwid:0 Rx invalid crypt:212 Rx invalid frag:0
    Tx excessive retries:1 Invalid misc:0 Missed beacon:0

    wmaster0 no wireless extensions.

    wlan0 IEEE 802.11bg ESSID:"Frank"
    Mode:Managed Frequency:2.437 GHz Access Point: 00:1C:DF:DA:F2:D1
    Bit Rate=1 Mb/s Tx-Power=27 dBm
    Retry min limit:7 RTS thr:off Fragment thr=2352 B
    Power Management:off
    Link Quality=94/100 Signal level:27/100
    Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
    Tx excessive retries:0 Invalid misc:0 Missed beacon:0

    pan0 no wireless extensions.

    craig@craig-laptop:~$ sudo iwlist scan
    lo Interface doesn't support scanning.

    eth0 Interface doesn't support scanning.

    eth1 Scan completed :
    Cell 01 - Address: 00:21:29:9F:30:EA
    ESSID:"lohe56-j"
    Mode:Master
    Channel:6
    Frequency:2.437 GHz (Channel 6)
    Signal level:45 dBm Noise level:16 dBm
    Encryption key:on
    Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s
    24 Mb/s; 36 Mb/s; 54 Mb/s
    Extra:bcn_int=100
    Extra:capab=0x0411
    Extra: Last beacon: 12ms ago
    Cell 02 - Address: 00:1C:DF:DA:F2:D1
    ESSID:"Frank"
    Mode:Master
    Channel:6
    Frequency:2.437 GHz (Channel 6)
    Signal level:48 dBm Noise level:16 dBm
    Encryption key:on
    Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 9 Mb/s
    18 Mb/s; 36 Mb/s; 54 Mb/s
    Extra:bcn_int=100
    Extra:capab=0x0411
    Extra: Last beacon: 12ms ago
    Cell 03 - Address: 00:22:75:27:63:ED
    ESSID:"Tardiff"
    Mode:Master
    Channel:6
    Frequency:2.437 GHz (Channel 6)
    Signal level:20 dBm Noise level:16 dBm
    Encryption key:on
    Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 9 Mb/s
    18 Mb/s; 36 Mb/s; 54 Mb/s
    Extra:bcn_int=100
    Extra:capab=0x0411
    Extra: Last beacon: 12ms ago
    Cell 04 - Address: 00:1B:5B:65:43:51
    ESSID:"2WIRE684"
    Mode:Master
    Channel:3
    Frequency:2.422 GHz (Channel 3)
    Signal level:28 dBm Noise level:16 dBm
    Encryption key:on
    Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s
    Extra:bcn_int=100
    Extra:capab=0x0011
    Extra: Last beacon: 12ms ago
    Cell 05 - Address: 00:16:B6:02:6E:52
    ESSID:"chipsnet"
    Mode:Master
    Channel:7
    Frequency:2.442 GHz (Channel 7)
    Signal level:22 dBm Noise level:16 dBm
    Encryption key:on
    Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s
    24 Mb/s; 36 Mb/s; 54 Mb/s
    Extra:bcn_int=100
    Extra:capab=0x0411
    Extra: Last beacon: 12ms ago

    wmaster0 Interface doesn't support scanning.

    wlan0 Scan completed :
    Cell 01 - Address: 00:21:1E:54:C9:90
    ESSID:"Skynet"
    Mode:Master
    Channel:1
    Frequency:2.412 GHz (Channel 1)
    Quality=94/100 Signal level:28/100
    Encryption key:on
    IE: Unknown: 0006536B796E6574
    IE: Unknown: 010582848B962C
    IE: Unknown: 030101
    IE: Unknown: 2A0104
    IE: Unknown: 32080C1218243048606C
    Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 22 Mb/s
    6 Mb/s; 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s
    36 Mb/s; 48 Mb/s; 54 Mb/s
    Extra:tsf=000000b807ffe1bf
    Extra: Last beacon: 676ms ago
    Cell 02 - Address: 00:1B:5B:65:43:51
    ESSID:"2WIRE684"
    Mode:Master
    Channel:3
    Frequency:2.422 GHz (Channel 3)
    Quality=17/100 Signal level:9/100
    Encryption key:on
    IE: Unknown: 00083257495245363834
    IE: Unknown: 010882848B0C12961824
    IE: Unknown: 030103
    IE: Unknown: 0706555320010B1B
    IE: Unknown: 2A0107
    IE: Unknown: 32043048606C
    Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 6 Mb/s; 9 Mb/s
    11 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s
    48 Mb/s; 54 Mb/s
    Extra:tsf=0000000e74ed4675
    Extra: Last beacon: 564ms ago
    Cell 03 - Address: 00:21:29:9F:30:EA
    ESSID:"lohe56-j"
    Mode:Master
    Channel:6
    Frequency:2.437 GHz (Channel 6)
    Quality=5/100 Signal level:32/100
    Encryption key:on
    IE: Unknown: 00086C6F686535362D6A
    IE: Unknown: 010882848B962430486C
    IE: Unknown: 030106
    IE: Unknown: 2A0104
    IE: Unknown: 2F0104
    IE: Unknown: 32040C121860
    IE: Unknown: DD09001018020015000000
    IE: WPA Version 1
    Group Cipher : TKIP
    Pairwise Ciphers (1) : TKIP
    Authentication Suites (1) : PSK
    Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s
    24 Mb/s; 36 Mb/s; 54 Mb/s; 6 Mb/s; 9 Mb/s
    12 Mb/s; 48 Mb/s
    Extra:tsf=0000007496162e6f
    Extra: Last beacon: 312ms ago
    Cell 04 - Address: 00:1C:DF:DA:F2:D1
    ESSID:"Frank"
    Mode:Master
    Channel:6
    Frequency:2.437 GHz (Channel 6)
    Quality=100/100 Signal level:28/100
    Encryption key:on
    IE: Unknown: 00054672616E6B
    IE: Unknown: 010882840B161224486C
    IE: Unknown: 030106
    IE: Unknown: 2A0104
    IE: Unknown: 32040C183060
    IE: Unknown: 2D1AEE110FFFFF0000010000000000000000000000000C0000 000000
    IE: Unknown: 3D1606070700000000000000000000000000000000000000
    IE: Unknown: 3E0100
    IE: WPA Version 1
    Group Cipher : TKIP
    Pairwise Ciphers (1) : TKIP
    Authentication Suites (1) : PSK
    IE: Unknown: DD180050F2020101000003A4000027A4000042435E0062322F 00
    IE: Unknown: 7F0101
    IE: Unknown: DD07000C4304000000
    IE: Unknown: DD1E00904C33EE110FFFFF0000010000000000000000000000 000C0000000000
    IE: Unknown: DD1A00904C3406070700000000000000000000000000000000 000000
    Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 9 Mb/s
    18 Mb/s; 36 Mb/s; 54 Mb/s; 6 Mb/s; 12 Mb/s
    24 Mb/s; 48 Mb/s
    Extra:tsf=0000000caaf0abab
    Extra: Last beacon: 388ms ago

    pan0 Interface doesn't support scanning.

    craig@craig-laptop:~$ sudo lshw -C network
    *-network:0
    description: Wireless interface
    product: Prism 2.5 Wavelan chipset
    vendor: Intersil Corporation
    physical id: 2
    bus info: pci@0000:02:02.0
    logical name: eth1
    version: 01
    serial: 00:02:8a:94:be:87
    width: 32 bits
    clock: 33MHz
    capabilities: pm cap_list ethernet physical wireless
    configuration: broadcast=yes driver=orinoco driverversion=0.15 firmware=Intersil 1.5.6 latency=64 link=yes module=orinoco_pci multicast=yes wireless=IEEE 802.11b
    *-network:1
    description: Ethernet interface
    product: 82801CAM (ICH3) PRO/100 VE (LOM) Ethernet Controller
    vendor: Intel Corporation
    physical id: 8
    bus info: pci@0000:02:08.0
    logical name: eth0
    version: 42
    serial: 08:00:46:ad:1d:0b
    size: 10MB/s
    capacity: 100MB/s
    width: 32 bits
    clock: 33MHz
    capabilities: pm bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation
    configuration: autonegotiation=on broadcast=yes driver=e100 driverversion=3.5.23-k6-NAPI duplex=half firmware=N/A latency=66 link=no maxlatency=56 mingnt=8 module=e100 multicast=yes port=MII speed=10MB/s
    *-network:0
    description: Wireless interface
    physical id: 1
    logical name: wlan0
    serial: 00:1c:df:78:1f:87
    capabilities: ethernet physical wireless


    Thanks for your help
    Last edited by snowcraig; June 3rd, 2009 at 03:39 PM.

  3. #1733
    Join Date
    Mar 2007
    Location
    Denver, CO
    Beans
    7,554
    Distro
    Ubuntu 12.04 Precise Pangolin

    Re: HOWTO: Wireless Security - WPA1, WPA2, LEAP, etc.

    Quote Originally Posted by snowcraig View Post


    Where do I get my network interface from?
    Its wlan0 -- thats your wireless interface

    *-network:0
    description: Wireless interface
    physical id: 1
    logical name: wlan0
    serial: 00:1c:df:78:1f:87
    capabilities: ethernet physical wireless
    configuration: broadcast=yes ip=192.168.2.3 multicast=yes wireless=IEEE 802.11bg

  4. #1734
    Join Date
    May 2009
    Beans
    12

    Re: HOWTO: Wireless Security - WPA1, WPA2, LEAP, etc.

    Ok, I will edit my original post then with the updated info. Just in case there is some confusion, I am currently using a USB stick to connect to the internet, but I have the internal wireless card turned on as well.

  5. #1735
    Join Date
    May 2006
    Location
    100acrewood
    Beans
    7,480
    Distro
    Kubuntu 14.04 Trusty Tahr

    Re: HOWTO: Wireless Security - WPA1, WPA2, LEAP, etc.

    snowcraig,

    There is a problem with your wireless device, it does not seem to support WPA. Could you do some googling on the topic and check it out? You might not be the only one having this issue.

  6. #1736
    Join Date
    May 2009
    Beans
    12

    Re: HOWTO: Wireless Security - WPA1, WPA2, LEAP, etc.

    It did support WPA when I had XP installed on the computer. It doesn't appear that the driver Ubuntu comes with for the device supports WPA however. Is there a way around that?

  7. #1737
    Join Date
    May 2006
    Location
    100acrewood
    Beans
    7,480
    Distro
    Kubuntu 14.04 Trusty Tahr

    Re: HOWTO: Wireless Security - WPA1, WPA2, LEAP, etc.

    Quote Originally Posted by snowcraig View Post
    It did support WPA when I had XP installed on the computer. It doesn't appear that the driver Ubuntu comes with for the device supports WPA however. Is there a way around that?
    Yes, using "ndiswrapper" could solve the problem.

    I wrote a tutorial on Ralink drivers and the use of ndiswrapper once, it might still do the job:

    http://ubuntuforums.org/showthread.php?t=563547

    If not, search for ndiswrapper. I believe it's the way to go in your case.

  8. #1738
    Join Date
    May 2009
    Beans
    12

    Re: HOWTO: Wireless Security - WPA1, WPA2, LEAP, etc.

    I have tried WPA supplicant, no luck there. I want to try ndiswrapper, but all I can find for the driver are windows installers, and I can't seem to find a way to get the actual driver files out of them. Anyone have any suggestions?

  9. #1739
    Join Date
    May 2006
    Location
    United Kingdom
    Beans
    469
    Distro
    Ubuntu 11.04 Natty Narwhal

    Re: HOWTO: Wireless Security - WPA1, WPA2, LEAP, etc.

    I had problems with a Edimx 7318UG (I think) until it went faulty. In the end I configured the network interfaces file manually. Obtained driver from this site.

    In case you haven't looked already you could look at the list here too?

    Good luck!

  10. #1740
    Join Date
    May 2006
    Location
    100acrewood
    Beans
    7,480
    Distro
    Kubuntu 14.04 Trusty Tahr

    Re: HOWTO: Wireless Security - WPA1, WPA2, LEAP, etc.

    Quote Originally Posted by snowcraig View Post
    I have tried WPA supplicant, no luck there. I want to try ndiswrapper, but all I can find for the driver are windows installers, and I can't seem to find a way to get the actual driver files out of them. Anyone have any suggestions?
    Occasionally these exe. files are ZIP archives which you can then open with your favorite zip tool and extract the files.

    Can you try?

Page 174 of 184 FirstFirst ... 74124164172173174175176 ... LastLast

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •