Hi,
i have the bcm4318 Card in my HP Pavilion Notebook and Ubuntu Edgy Eft amd64 on Kernel 2.6.19 (from http://ubuntuforums.org/showpost.php...postcount=668), i have successfully installed the ndiswrapper 1.27 Driver. The scan finds my wireless network, but it doesn't connect, not with NetworkManager and not with wpa_supplicant.
The NetworkManager asks a Password and twirls the whole time, until it stops and everything is like before.
I think the wpa_spplicant has an error, but look self :
Code:
unregistr3d@ubuntu-laptop1:~$ sudo iwconfig
lo no wireless extensions.
eth1 no wireless extensions.
eth0 IEEE 802.11g ESSID:off/any
Mode:Managed Frequency:2.462 GHz Access Point: Not-Associated
Bit Rate=54 Mb/s Tx-Power:25 dBm
RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
unregistr3d@ubuntu-laptop1:~$ sudo iwlist eth0 scan
eth0 Scan completed :
Cell 01 - Address: 00:14:6C:D9:85:B4
ESSID:"gatandWLAN"
Protocol:IEEE 802.11g
Mode:Managed
Frequency:2.462 GHz (Channel 11)
Quality:0/100 Signal level:-57 dBm Noise level:-256 dBm
Encryption key:on
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s
12 Mb/s; 24 Mb/s; 36 Mb/s; 9 Mb/s; 18 Mb/s
48 Mb/s; 54 Mb/s
Extra:bcn_int=100
Extra:atim=0
IE: WPA Version 1
Group Cipher : TKIP
Pairwise Ciphers (1) : TKIP
Authentication Suites (1) : PSK
unregistr3d@ubuntu-laptop1:~$ sudo wpa_supplicant -ieth0 -Dndiswrapper -c/etc/wpa_supplicant/wpa_supplicant.conf -B -d
Initializing interface 'eth0' conf '/etc/wpa_supplicant/wpa_supplicant.conf' driver 'ndiswrapper' ctrl_interface 'N/A' bridge 'N/A'
Configuration file '/etc/wpa_supplicant/wpa_supplicant.conf' -> '/etc/wpa_supplicant/wpa_supplicant.conf'
Reading configuration file '/etc/wpa_supplicant/wpa_supplicant.conf'
ctrl_interface='/var/run/wpa_supplicant'
Priority group 0
id=0 ssid='gatandWLAN'
Initializing interface (2) 'eth0'
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
SIOCGIWRANGE: WE(compiled)=21 WE(source)=18 enc_capa=0xf
capabilities: key_mgmt 0xf enc 0xf
WEXT: Operstate: linkmode=1, operstate=5
Own MAC address: 00:14:a5:67:41:94
Driver does not support WPA.
wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0
Setting scan request: 0 sec 100000 usec
Added interface eth0
Daemonize..
Sorry for my bad english, i'm from austria
Bookmarks