Page 1 of 2 12 LastLast
Results 1 to 10 of 13

Thread: Upgraded to 10.04 and now both wireless and wired networking are disabled

  1. #1
    Join Date
    Mar 2008
    Beans
    33

    Angry Upgraded to 10.04 and now both wireless and wired networking are disabled

    Upgraded to 10.04 and now both wireless and wired networking are disabled. Please help.

    Here's some info that I see people provide in other similar threads:

    eth0 Link encap:Ethernet HWaddr 00:1c:25:3c:a2:9b
    inet6 addr: fe80::21c:25ff:fe3c:a29b/64 Scope:Link
    UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
    RX packets:0 errors:0 dropped:0 overruns:0 frame:0
    TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:1000
    RX bytes:0 (0.0 B) TX bytes:1152 (1.1 KB)
    Interrupt:19

    lo Link encap:Local Loopback
    inet addr:127.0.0.1 Mask:255.0.0.0
    inet6 addr: ::1/128 Scope:Host
    UP LOOPBACK RUNNING MTU:16436 Metric:1
    RX packets:96 errors:0 dropped:0 overruns:0 frame:0
    TX packets:96 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:0
    RX bytes:10991 (10.9 KB) TX bytes:10991 (10.9 KB)

    mark@kitchen-desktop-ubuntu64:~$ dmesg | grep -i eth
    [ 1.037662] sky2 eth0: addr 00:1c:25:3c:a2:9b
    [ 29.694715] sky2 eth0: enabling interface
    [ 29.695774] ADDRCONF(NETDEV_UP): eth0: link is not ready
    [ 31.661456] sky2 eth0: Link is up at 100 Mbps, full duplex, flow control rx
    [ 31.662581] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
    [ 42.272513] eth0: no IPv6 routers present
    [ 156.342534] sky2 eth0: disabling interface
    [ 167.288237] sky2 eth0: enabling interface
    [ 167.290512] ADDRCONF(NETDEV_UP): eth0: link is not ready
    [ 169.350316] sky2 eth0: Link is up at 100 Mbps, full duplex, flow control rx
    [ 169.352502] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
    [ 180.250025] eth0: no IPv6 routers present


    Settings for eth0:
    Supported ports: [ TP ]
    Supported link modes: 10baseT/Half 10baseT/Full
    100baseT/Half 100baseT/Full
    1000baseT/Half 1000baseT/Full
    Supports auto-negotiation: Yes
    Advertised link modes: 10baseT/Half 10baseT/Full
    100baseT/Half 100baseT/Full
    1000baseT/Half 1000baseT/Full
    Advertised pause frame use: No
    Advertised auto-negotiation: Yes
    Link partner advertised link modes: Not reported
    Link partner advertised pause frame use: No
    Link partner advertised auto-negotiation: No
    Speed: 100Mb/s
    Duplex: Full
    Port: Twisted Pair
    PHYAD: 0
    Transceiver: internal
    Auto-negotiation: on
    MDI-X: Unknown
    Supports Wake-on: pg
    Wake-on: d
    Current message level: 0x000000ff (255)
    Link detected: yes

    mark@kitchen-desktop-ubuntu64:~$ cat /etc/network/interfaces
    auto lo
    iface lo inet loopback


    00:00.0 Host bridge: ATI Technologies Inc RS690 Host Bridge
    Subsystem: Foxconn International, Inc. Device 0e0a
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
    Latency: 64

    00:01.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (Internal gfx)
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 99
    Bus: primary=00, secondary=01, subordinate=01, sec-latency=68
    I/O behind bridge: 0000d000-0000dfff
    Memory behind bridge: fdd00000-fdefffff
    Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff
    Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
    BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
    PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
    Capabilities: [44] HyperTransport: MSI Mapping Enable+ Fixed+
    Capabilities: [b0] Subsystem: Foxconn International, Inc. Device 0e0a
    Kernel modules: shpchp

    00:07.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 3)
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0, Cache Line Size: 4 bytes
    Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
    I/O behind bridge: 0000e000-0000efff
    Memory behind bridge: fdc00000-fdcfffff
    Prefetchable memory behind bridge: 00000000fdf00000-00000000fdffffff
    Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
    BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
    PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
    Capabilities: [50] Power Management version 3
    Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    Capabilities: [58] Express (v1) Root Port (Slot+), MSI 00
    DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
    ExtTag+ RBE+ FLReset-
    DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
    RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
    MaxPayload 128 bytes, MaxReadReq 128 bytes
    DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
    LnkCap: Port #4, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <64ns, L1 <1us
    ClockPM- Suprise- LLActRep+ BwNot-
    LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
    ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
    LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-
    SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise-
    Slot # 6, PowerLimit 25.000000; Interlock- NoCompl-
    SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
    Control: AttnInd Off, PwrInd Off, Power- Interlock-
    SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
    Changed: MRL- PresDet+ LinkState-
    RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
    RootCap: CRSVisible-
    RootSta: PME ReqID 0000, PMEStatus- PMEPending-
    Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
    Address: fee0300c Data: 4149
    Capabilities: [b0] Subsystem: Foxconn International, Inc. Device 0e0a
    Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
    Capabilities: [100] Virtual Channel <?>
    Kernel driver in use: pcieport
    Kernel modules: shpchp

    00:12.0 SATA controller: ATI Technologies Inc SB600 Non-Raid-5 SATA (prog-if 01)
    Subsystem: Foxconn International, Inc. Device 0e0a
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 64
    Interrupt: pin A routed to IRQ 22
    Region 0: I/O ports at ff00 [size=8]
    Region 1: I/O ports at fe00 [size=4]
    Region 2: I/O ports at fd00 [size=8]
    Region 3: I/O ports at fc00 [size=4]
    Region 4: I/O ports at fb00 [size=16]
    Region 5: Memory at fe02f000 (32-bit, non-prefetchable) [size=1K]
    Capabilities: [60] Power Management version 2
    Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    Kernel driver in use: ahci
    Kernel modules: ahci

    00:13.0 USB Controller: ATI Technologies Inc SB600 USB (OHCI0) (prog-if 10)
    Subsystem: Foxconn International, Inc. Device 0e0a
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 64, Cache Line Size: 4 bytes
    Interrupt: pin A routed to IRQ 16
    Region 0: Memory at fe02e000 (32-bit, non-prefetchable) [size=4K]
    Kernel driver in use: ohci_hcd

    00:13.1 USB Controller: ATI Technologies Inc SB600 USB (OHCI1) (prog-if 10)
    Subsystem: Foxconn International, Inc. Device 0e0a
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 64, Cache Line Size: 4 bytes
    Interrupt: pin B routed to IRQ 17
    Region 0: Memory at fe02d000 (32-bit, non-prefetchable) [size=4K]
    Kernel driver in use: ohci_hcd

    00:13.2 USB Controller: ATI Technologies Inc SB600 USB (OHCI2) (prog-if 10)
    Subsystem: Foxconn International, Inc. Device 0e0a
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 64, Cache Line Size: 4 bytes
    Interrupt: pin C routed to IRQ 18
    Region 0: Memory at fe02c000 (32-bit, non-prefetchable) [size=4K]
    Kernel driver in use: ohci_hcd

    00:13.3 USB Controller: ATI Technologies Inc SB600 USB (OHCI3) (prog-if 10)
    Subsystem: Foxconn International, Inc. Device 0e0a
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 64, Cache Line Size: 4 bytes
    Interrupt: pin B routed to IRQ 17
    Region 0: Memory at fe02b000 (32-bit, non-prefetchable) [size=4K]
    Kernel driver in use: ohci_hcd

    00:13.4 USB Controller: ATI Technologies Inc SB600 USB (OHCI4) (prog-if 10)
    Subsystem: Foxconn International, Inc. Device 0e0a
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 64, Cache Line Size: 4 bytes
    Interrupt: pin C routed to IRQ 18
    Region 0: Memory at fe02a000 (32-bit, non-prefetchable) [size=4K]
    Kernel driver in use: ohci_hcd

    00:13.5 USB Controller: ATI Technologies Inc SB600 USB Controller (EHCI) (prog-if 20)
    Subsystem: Foxconn International, Inc. Device 0e0a
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 64, Cache Line Size: 64 bytes
    Interrupt: pin D routed to IRQ 19
    Region 0: Memory at fe029000 (32-bit, non-prefetchable) [size=256]
    Capabilities: [c0] Power Management version 2
    Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    Bridge: PM- B3+
    Capabilities: [e4] Debug port: BAR=1 offset=00e0
    Kernel driver in use: ehci_hcd

    00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 14)
    Subsystem: Foxconn International, Inc. Device 0e0a
    Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
    Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Region 0: I/O ports at 0b00 [size=16]
    Capabilities: [b0] HyperTransport: MSI Mapping Enable- Fixed+
    Kernel driver in use: piix4_smbus
    Kernel modules: i2c-piix4

    00:14.1 IDE interface: ATI Technologies Inc SB600 IDE (prog-if 8a [Master SecP PriP])
    Subsystem: Foxconn International, Inc. Device 0e0a
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 64
    Interrupt: pin A routed to IRQ 16
    Region 0: I/O ports at 01f0 [size=8]
    Region 1: I/O ports at 03f4 [size=1]
    Region 2: I/O ports at 0170 [size=8]
    Region 3: I/O ports at 0374 [size=1]
    Region 4: I/O ports at f900 [size=16]
    Kernel driver in use: pata_atiixp
    Kernel modules: pata_atiixp

    00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA)
    Subsystem: Foxconn International, Inc. Device 0e0a
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 64, Cache Line Size: 4 bytes
    Interrupt: pin ? routed to IRQ 16
    Region 0: Memory at fe024000 (64-bit, non-prefetchable) [size=16K]
    Capabilities: [50] Power Management version 2
    Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    Kernel driver in use: HDA Intel
    Kernel modules: snd-hda-intel

    00:14.3 ISA bridge: ATI Technologies Inc SB600 PCI to LPC Bridge
    Subsystem: Foxconn International, Inc. Device 0e0a
    Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0

    00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge (prog-if 01)
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 64
    Bus: primary=00, secondary=03, subordinate=03, sec-latency=64
    I/O behind bridge: 0000c000-0000cfff
    Memory behind bridge: fdb00000-fdbfffff
    Prefetchable memory behind bridge: fda00000-fdafffff
    Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
    BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
    PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-

    00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
    Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Capabilities: [80] HyperTransport: Host or Secondary Interface
    !!! Possibly incomplete decoding
    Command: WarmRst+ DblEnd-
    Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
    Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
    Revision ID: 1.02

    00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
    Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

    00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
    Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Kernel modules: amd64_edac_mod

    00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
    Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Capabilities: [f0] Secure device <?>
    Kernel driver in use: k8temp
    Kernel modules: k8temp

    01:05.0 VGA compatible controller: ATI Technologies Inc RS690 [Radeon X1200 Series]
    Subsystem: Foxconn International, Inc. Device 0e0a
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 64, Cache Line Size: 4 bytes
    Interrupt: pin A routed to IRQ 18
    Region 0: Memory at d0000000 (64-bit, prefetchable) [size=256M]
    Region 2: Memory at fdef0000 (64-bit, non-prefetchable) [size=64K]
    Region 4: I/O ports at de00 [size=256]
    Region 5: Memory at fdd00000 (32-bit, non-prefetchable) [size=1M]
    Capabilities: [50] Power Management version 2
    Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    Capabilities: [80] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
    Address: 0000000000000000 Data: 0000
    Kernel driver in use: radeon
    Kernel modules: radeon

    02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8056 PCI-E Gigabit Ethernet Controller (rev 20)
    Subsystem: Foxconn International, Inc. Device 0e0a
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0, Cache Line Size: 4 bytes
    Interrupt: pin A routed to IRQ 25
    Region 0: Memory at fdcfc000 (64-bit, non-prefetchable) [size=16K]
    Region 2: I/O ports at ee00 [size=256]
    [virtual] Expansion ROM at fdf00000 [disabled] [size=128K]
    Capabilities: [48] Power Management version 3
    Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
    Status: D0 PME-Enable- DSel=0 DScale=1 PME-
    Capabilities: [50] Vital Product Data <?>
    Capabilities: [5c] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable+
    Address: 00000000fee0300c Data: 4179
    Capabilities: [e0] Express (v1) Legacy Endpoint, MSI 00
    DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited
    ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
    DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
    RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
    MaxPayload 128 bytes, MaxReadReq 512 bytes
    DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
    LnkCap: Port #4, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <256ns, L1 unlimited
    ClockPM+ Suprise- LLActRep- BwNot-
    LnkCtl: ASPM Disabled; RCB 128 bytes Disabled- Retrain- CommClk+
    ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
    LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
    Capabilities: [100] Advanced Error Reporting <?>
    Kernel driver in use: sky2
    Kernel modules: sky2

    03:00.0 FireWire (IEEE 1394): Texas Instruments TSB43AB23 IEEE-1394a-2000 Controller (PHY/Link) (prog-if 10)
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 64 (500ns min, 1000ns max), Cache Line Size: 4 bytes
    Interrupt: pin A routed to IRQ 20
    Region 0: Memory at fdbff000 (32-bit, non-prefetchable) [size=2K]
    Region 1: Memory at fdbf8000 (32-bit, non-prefetchable) [size=16K]
    Capabilities: [44] Power Management version 2
    Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME+
    Kernel driver in use: ohci1394
    Kernel modules: firewire-ohci, ohci1394

    03:01.0 Modem: Motorola SM56 Data Fax Modem (rev 04)
    Subsystem: Motorola Device 3020
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 64 (250ns min, 15500ns max), Cache Line Size: 4 bytes
    Interrupt: pin A routed to IRQ 21
    Region 0: Memory at fdbfe000 (32-bit, non-prefetchable) [size=4K]
    Region 1: I/O ports at ce00 [size=256]
    Capabilities: [80] Power Management version 2
    Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    Kernel driver in use: serial

    03:06.0 FireWire (IEEE 1394): Texas Instruments TSB43AB23 IEEE-1394a-2000 Controller (PHY/Link) (prog-if 10)
    Subsystem: Foxconn International, Inc. Device 0e0a
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 64 (500ns min, 1000ns max), Cache Line Size: 4 bytes
    Interrupt: pin A routed to IRQ 23
    Region 0: Memory at fdbfd000 (32-bit, non-prefetchable) [size=2K]
    Region 1: Memory at fdbf4000 (32-bit, non-prefetchable) [size=16K]
    Capabilities: [44] Power Management version 2
    Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME+
    Kernel driver in use: ohci1394
    Kernel modules: firewire-ohci, ohci1394


    mark@kitchen-desktop-ubuntu64:~$ dmesg | grep -i eth
    [ 1.037662] sky2 eth0: addr 00:1c:25:3c:a2:9b
    [ 29.694715] sky2 eth0: enabling interface
    [ 29.695774] ADDRCONF(NETDEV_UP): eth0: link is not ready
    [ 31.661456] sky2 eth0: Link is up at 100 Mbps, full duplex, flow control rx
    [ 31.662581] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
    [ 42.272513] eth0: no IPv6 routers present
    [ 156.342534] sky2 eth0: disabling interface
    [ 167.288237] sky2 eth0: enabling interface
    [ 167.290512] ADDRCONF(NETDEV_UP): eth0: link is not ready
    [ 169.350316] sky2 eth0: Link is up at 100 Mbps, full duplex, flow control rx
    [ 169.352502] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
    [ 180.250025] eth0: no IPv6 routers present



    mark@kitchen-desktop-ubuntu64:~$ ifconfig
    eth0 Link encap:Ethernet HWaddr 00:1c:25:3c:a2:9b
    inet6 addr: fe80::21c:25ff:fe3c:a29b/64 Scope:Link
    UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
    RX packets:0 errors:0 dropped:0 overruns:0 frame:0
    TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:1000
    RX bytes:0 (0.0 B) TX bytes:1152 (1.1 KB)
    Interrupt:19

    lo Link encap:Local Loopback
    inet addr:127.0.0.1 Mask:255.0.0.0
    inet6 addr: ::1/128 Scope:Host
    UP LOOPBACK RUNNING MTU:16436 Metric:1
    RX packets:368 errors:0 dropped:0 overruns:0 frame:0
    TX packets:368 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:0
    RX bytes:32079 (32.0 KB) TX bytes:32079 (32.0 KB)

  2. #2
    Join Date
    Sep 2011
    Beans
    3

    Re: Upgraded to 10.04 and now both wireless and wired networking are disabled

    the wired device looks ok, if i don't overlook something. Have you tried ?
    Code:
    sudo dhclient eth0
    but I can't see your wireless device. What says ?
    Code:
    sudo iwconfig
    I also realized that only the loopback interface is in /etc/network/interfaces
    mark@kitchen-desktop-ubuntu64:~$ cat /etc/network/interfaces
    auto lo
    iface lo inet loopback
    don't know if this is normal in ubuntu cause networkmanager or something never used it yet

  3. #3
    Join Date
    Mar 2008
    Beans
    33

    Re: Upgraded to 10.04 and now both wireless and wired networking are disabled

    Thanks for your response, vst0rm. I should have mentioned that the reason I switched to wired was because I discovered that the wireless has stopped working after the upgrade. I moved my wireless router in closer proximity to my computer and then hard-wired it. The Windows boot picked up the hard-wired router/DHCP server just fine. But if I boot to Ubuntu, it tells me there is no network connection.

    Here are the results:

    mark@kitchen-desktop-ubuntu64:~$ sudo dhclient eth0
    [sudo] password for mark:
    Internet Systems Consortium DHCP Client V3.1.3
    Copyright 2004-2009 Internet Systems Consortium.
    All rights reserved.
    For info, please visit https://www.isc.org/software/dhcp/

    Listening on LPF/eth0/00:1c:25:3c:a2:9b
    Sending on LPF/eth0/00:1c:25:3c:a2:9b
    Sending on Socket/fallback
    DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 6
    DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 6
    DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 11
    DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 7
    DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 19
    DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 10
    DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 2
    No DHCPOFFERS received.
    No working leases in persistent database - sleeping.
    mark@kitchen-desktop-ubuntu64:~$

  4. #4
    Join Date
    Sep 2011
    Beans
    3

    Re: Upgraded to 10.04 and now both wireless and wired networking are disabled

    you could try to setup static IP but I guess this wouldn't work either
    Code:
    sudo ifconfig eth0 "IP" netmask "netmask" up
    sudo route add default gw "route IP" dev eth0
    ping "router IP"
    example:
    Code:
    sudo ifconfig eth0 192.168.1.66 netmask 255.255.255.0 up
    sudo route add default gw 192.168.1.1 dev eth0
    ping 192.168.1.1
    I have no idea what this could be don't see any error ... hope someone else have some ideas sorry for my english ^^

  5. #5
    Join Date
    Apr 2005
    Beans
    2,068

    Re: Upgraded to 10.04 and now both wireless and wired networking are disabled

    here is a diagnostic script; developed by a linux wireless expert

    http://www.linux-tips-and-tricks.de/...t.html#English

    run this; it should offer suggestions; post the results back here;

    let's see if it can get you going

  6. #6
    Join Date
    Mar 2008
    Beans
    33

    Re: Upgraded to 10.04 and now both wireless and wired networking are disabled

    Code:
    collectNWData.sh V0.6.5.4.5 (Rev: 1.291, Build: 2011/09/17 12:11:25 UTC)
    --- Which type of your network connection should be tested?
    --- (1) Wired connection
    --- What's the type of networktopology?
    --- (1) DSL modem <---> LinuxClient
    --- On which host is the script executed?
    --- (1) LinuxClient
    
    --- NWEliza is analyzing the system for common network configuration errors ...
    
    !!! CND0120E: Network card eth0 has no IP address
    !!! CND0450W: WLAN key masquerading is not fully tested on this distribution. Please check output file collectNWData.txt for visible WLAN keys and masquerade them manually
    
    --- Go to http://www.linux-tips-and-tricks.de/CND#English to get more detailed instructions 
    --- about the error/warning messages and how to fix the problems on your own.
    
    --- If you are unsuccessful then place the contents of file collectNWData.txt in the net
    --- (see http://www.linux-tips-and-tricks.de/CND_UPL#English for links) 
    --- and then paste the nopaste link on your favorite Linux forum.
    
    ==================================================================================================================
    ===== cat /etc/*[-_]release || cat /etc/*[-_]version =============================================================
    /etc/lsb-release
    DISTRIB_ID=Ubuntu
    DISTRIB_RELEASE=10.04
    DISTRIB_CODENAME=lucid
    DISTRIB_DESCRIPTION="Ubuntu 10.04.2 LTS"
    ===== uname -a ===================================================================================================
    Linux kitchen-desktop-ubuntu64 2.6.32-32-generic #62-Ubuntu SMP Wed Apr 20 21:52:38 UTC 2011 x86_64 GNU/Linux
    ===== lspci ======================================================================================================
    02:00.0 Ethernet controller [0200]: Marvell Technology Group Ltd. 88E8056 PCI-E Gigabit Ethernet Controller [11ab:4364] (rev 20)
    	Kernel driver in use: sky2
    	Kernel modules: sky2
    ===== lsusb | grep -v "root hub" =================================================================================
    Bus 004 Device 002: ID 058f:9360 Alcor Micro Corp. 8-in-1 Media Card Reader
    Bus 002 Device 002: ID 045e:0084 Microsoft Corp. Basic Optical Mouse
    Bus 001 Device 003: ID 03f0:5c11 Hewlett-Packard PhotoSmart C4200 Printer series
    ===== lshw -C network (filtered) =================================================================================
           product: 88E8056 PCI-E Gigabit Ethernet Controller
           vendor: Marvell Technology Group Ltd.
           capabilities: pm vpd msi pciexpress bus_master cap_list rom ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation
           configuration: autonegotiation=on broadcast=yes driver=sky2 driverversion=1.25 duplex=full firmware=N/A latency=0 link=yes multicast=yes port=twisted pair speed=100MB/s
    ===== lsmod (filtered) ===========================================================================================
    | ahci            | binfmt_misc     | bitblit         | drm             | drm_kms_helper   |
    | edac_core       | edac_mce_amd    | fbcon           | font            | hid              |
    | i2c_algo_bit    | i2c_piix4       | ieee1394        | k8temp          | led_class        |
    | lp              | ohci1394        | ppdev           | radeon          | serio_raw        |
    | shpchp          | sky2            | softcursor      | tileblit        | ttm              |
    | usblp           | usb_storage     | vga16fb         | vgastate        |
    ===== ifconfig (filtered for eth|wlan|ra|ath|dsl) ================================================================
    eth0      Link encap:Ethernet  HWaddr ##:##:##:##:##:#1  
              inet6 addr: fe80::21c:25ff:fe3c:a29b/64 Scope:Link
              UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
              RX packets:0 errors:0 dropped:0 overruns:0 frame:0
              TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
              collisions:0 txqueuelen:1000 
              RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
              Interrupt:19 
    ===== cat /etc/network/interfaces | grep -v "=''" ================================================================
    --- /etc/network/interfaces
    auto lo
    iface lo inet loopback
    ===== ping tests =================================================================================================
    connect: Network is unreachable
    Ping of 195.135.220.3 failed
    ping: unknown host www.suse.de
    Ping of www.suse.de failed
    ===== cat /etc/resolv | grep -i "nameserver" =====================================================================
    ===== cat /etc/hosts =============================================================================================
    127.0.0.1	localhost
    127.0.1.1	kitchen-desktop-ubuntu64
    ===== route -n | egrep "(eth|ath|ra|wlan|dsl)" ===================================================================
    ===== egrep 'eth|ath|wlan|ra' /etc/udev/rules.d/*net_persistent* /etc/udev/rules.d/*persistent-net* ==============
    /etc/udev/rules.d/70-persistent-net.rules:SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="##:##:##:##:##:#1", ATTR{type}=="1", KERNEL=="eth*", NAME="eth0"
    /etc/udev/rules.d/70-persistent-net.rules:SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="##:##:##:##:##:#2", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="wlan*", NAME="wlan0"
    ==================================================================================================================
    *** NWElizaStates V0.6.5.4.5
    IF:eth0 IM:1 DI:1 FALON:1 NIC:1 cNiC:1:1 NI:2 cNI:2 NIWD:0 IP6:0 WLW:0 RTDT:debian

  7. #7
    Join Date
    Sep 2010
    Location
    Germany
    Beans
    52
    Distro
    Ubuntu 11.10 Oneiric Ocelot

    Re: Upgraded to 10.04 and now both wireless and wired networking are disabled

    Hi,
    for your wired card try the following:

    Installing Marvell Yukon 88E8056 driver on Ubuntu:

    Please login as root and install the following driver as follows:
    http://www.marvell.com/support.html -> "88E8056 Search" -> Kernel 2.6.x Linux Driver Install Package for Yukon Devices Linux 2.6 ... v10.90.5.3

    $ sudo bash ./install.sh

    and let me know if it works.

    Have a lot of fun ...

  8. #8
    Join Date
    Mar 2008
    Beans
    33

    Re: Upgraded to 10.04 and now both wireless and wired networking are disabled

    Running
    Code:
    $ sudo bash ./install.sh
    Completed with no errors but it didn't enable my networking.
    I logged out and logged back in: still no networking.
    I rebooted: still no networking.

    They should call it "notworking" instead of "networking".

    Thanks all for the attempts to help. I'm running out of patience but I'm willing to give it one more try if there is someone out there who can think of a solution.
    Last edited by mlebaron; September 20th, 2011 at 05:11 AM. Reason: Initial information was incorrect. Augmented comments.

  9. #9
    Join Date
    Mar 2008
    Beans
    33

    Re: Upgraded to 10.04 and now both wireless and wired networking are disabled

    V$torm, I tried setting up a static IP address but that didn't help. Afterward, I tried pinging the router but it didn't even try to ping; it just said no networking available (or words to that effect).

  10. #10
    Join Date
    Mar 2008
    Beans
    33

    Re: Upgraded to 10.04 and now both wireless and wired networking are disabled

    Here's my latest ifconfig

    Code:
    mark@kitchen-desktop-ubuntu64:~$ ifconfig
    eth0      Link encap:Ethernet  HWaddr 00:1c:25:3c:a2:9b  
              inet addr:192.168.1.66  Bcast:192.168.1.255  Mask:255.255.255.0
              inet6 addr: fe80::21c:25ff:fe3c:a29b/64 Scope:Link
              UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
              RX packets:0 errors:0 dropped:0 overruns:0 frame:0
              TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
              collisions:0 txqueuelen:1000 
              RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
              Interrupt:19 
    
    lo        Link encap:Local Loopback  
              inet addr:127.0.0.1  Mask:255.0.0.0
              inet6 addr: ::1/128 Scope:Host
              UP LOOPBACK RUNNING  MTU:16436  Metric:1
              RX packets:115 errors:0 dropped:0 overruns:0 frame:0
              TX packets:115 errors:0 dropped:0 overruns:0 carrier:0
              collisions:0 txqueuelen:0 
              RX bytes:12914 (12.9 KB)  TX bytes:12914 (12.9 KB)
    
    mark@kitchen-desktop-ubuntu64:~$

Page 1 of 2 12 LastLast

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •