Page 1 of 5 123 ... LastLast
Results 1 to 10 of 49

Thread: AWLL5088 Airlink 101 installation help

  1. #1
    Join Date
    Oct 2008
    Beans
    375
    Distro
    Ubuntu 10.04 Lucid Lynx

    AWLL5088 Airlink 101 installation help

    I have searched the forums and followed the directions for the other airlink usb adapters and still no luck getting this one up and running.

    Here is my dmesg after inserting these are the new lines.

    [ 4632.987427] usb 2-3: USB disconnect, address 2
    [ 4638.608035] usb 2-3: new high speed USB device using ehci_hcd and address 4
    [ 4638.741909] usb 2-3: configuration #1 chosen from 1 choice

    lsusb gives me this:

    david@david-laptop:~$ lsusb
    Bus 002 Device 004: ID 0bda:8176 Realtek Semiconductor Corp.
    Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
    Bus 004 Device 002: ID 0a12:0001 Cambridge Silicon Radio, Ltd Bluetooth Dongle (HCI mode)
    Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
    Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
    Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
    Bus 001 Device 002: ID 0bda:0158 Realtek Semiconductor Corp. Mass Stroage Device


    I have tried the HardwareSupportComponentsWirelessNetworkCardsAirli nk101 and followed those directions but still nothing.

    Any help would be appreciated.
    Compaq CQ60-215DX // AMD Athlon Dual Core QL-62 // 2.0 Gb Ram
    Ubuntu Lucid Lynx 10.04.2 64bit // Kernel 2.6.32-28-generic // Gnome 2.30.2
    Acer AspireONE / Lucid Lynx 10.04
    Ubuntu User #: 26559 // Linux User #: 486156

  2. #2
    Join Date
    Oct 2008
    Beans
    375
    Distro
    Ubuntu 10.04 Lucid Lynx

    Re: AWLL5088 Airlink 101 installation help

    Okay so I have downloaded the realtek drivers and did the make, and sudo make install and then all went to garbage...

    KERNEL Panic!! Rebooted same kernel panic!

    Took out the USB wifi airlink101 and rebooted, my built in atheros card now is not working, compiled and installed those drivers, rebooted and now I am back at least with the atheros G wifi.

    So I am back now to not having the new wireless N functioning... Any ideas?

    Oh and by the way the lsusb -v output shows the wireless N adapter as shown here

    Bus 002 Device 002: ID 0bda:8176 Realtek Semiconductor Corp.
    Device Descriptor:
    bLength 18
    bDescriptorType 1
    bcdUSB 2.00
    bDeviceClass 0 (Defined at Interface level)
    bDeviceSubClass 0
    bDeviceProtocol 0
    bMaxPacketSize0 64
    idVendor 0x0bda Realtek Semiconductor Corp.
    idProduct 0x8176
    bcdDevice 2.00
    iManufacturer 1 Realtek
    iProduct 2 Wireless N USB Adapter
    iSerial 3 00e04c000001
    bNumConfigurations 1
    Configuration Descriptor:
    bLength 9
    bDescriptorType 2
    wTotalLength 46
    bNumInterfaces 1
    bConfigurationValue 1
    iConfiguration 0
    bmAttributes 0x80
    (Bus Powered)
    MaxPower 500mA
    Interface Descriptor:
    bLength 9
    bDescriptorType 4
    bInterfaceNumber 0
    bAlternateSetting 0
    bNumEndpoints 4
    bInterfaceClass 255 Vendor Specific Class
    bInterfaceSubClass 255 Vendor Specific Subclass
    bInterfaceProtocol 255 Vendor Specific Protocol
    iInterface 0
    Endpoint Descriptor:
    bLength 7
    bDescriptorType 5
    bEndpointAddress 0x81 EP 1 IN
    bmAttributes 2
    Transfer Type Bulk
    Synch Type None
    Usage Type Data
    wMaxPacketSize 0x0200 1x 512 bytes
    bInterval 0
    Endpoint Descriptor:
    bLength 7
    bDescriptorType 5
    bEndpointAddress 0x02 EP 2 OUT
    bmAttributes 2
    Transfer Type Bulk
    Synch Type None
    Usage Type Data
    wMaxPacketSize 0x0200 1x 512 bytes
    bInterval 0
    Endpoint Descriptor:
    bLength 7
    bDescriptorType 5
    bEndpointAddress 0x03 EP 3 OUT
    bmAttributes 2
    Transfer Type Bulk
    Synch Type None
    Usage Type Data
    wMaxPacketSize 0x0200 1x 512 bytes
    bInterval 0
    Endpoint Descriptor:
    bLength 7
    bDescriptorType 5
    bEndpointAddress 0x84 EP 4 IN
    bmAttributes 3
    Transfer Type Interrupt
    Synch Type None
    Usage Type Data
    wMaxPacketSize 0x0040 1x 64 bytes
    bInterval 1
    Device Qualifier (for other device speed):
    bLength 10
    bDescriptorType 6
    bcdUSB 2.00
    bDeviceClass 0 (Defined at Interface level)
    bDeviceSubClass 0
    bDeviceProtocol 0
    bMaxPacketSize0 64
    bNumConfigurations 1
    Device Status: 0x0000
    (Bus Powered)
    Compaq CQ60-215DX // AMD Athlon Dual Core QL-62 // 2.0 Gb Ram
    Ubuntu Lucid Lynx 10.04.2 64bit // Kernel 2.6.32-28-generic // Gnome 2.30.2
    Acer AspireONE / Lucid Lynx 10.04
    Ubuntu User #: 26559 // Linux User #: 486156

  3. #3
    Join Date
    Oct 2008
    Beans
    375
    Distro
    Ubuntu 10.04 Lucid Lynx

    Re: AWLL5088 Airlink 101 installation help

    After almost giving up I decided to go to the "Supported wireless cards list and procedure to get help." thread once again and try one more time.

    Went to the wiki of supported cards and selected Airlink101. It still lists "Download kernel module sources from 'Realtek' (current filename: 'RTL8188CUS_v2.0.1212.zip'), extract to /usr/src , and run install.sh" for this super nano N usb adapter. However, after going to the Realtek page I noticed that there is a different version now available!

    NOTE THE WIKI has been updated with the new current version and the link as well.

    Version Update
    Linux driver for Kernel 2.6.x 2.0.1324 2011/1/28 2226k
    Link to driver: RTL8188CUS - Linux driver

    Downloaded that version and followed the directions to extract it to the /usr/src folder and then ran the install.sh and to my shock and awe the wireless adapter sprung to life!

    Sure then I had a little conflict with the internal wifi still being on and trying to keep control. Both by the way would connect and work at the same time. But for my sake of sanity I hit the wifi button on the laptop that is supposed to turn off the internal and although the light kept going the internal shut off. Now several boots later and I am solely using this new N adapter!

    I must say it is stronger to connect to my home wifi however it doesn't see as many access points in the neighborhood as the internal wifi had. Not sure why but as long as I can connect to my home setup I am ecstatic!

    So for anyone looking into the Airlink101 AWLL5088 adapter It is a great way of adding N for those who are looking at running N but have an antiquated internal card that can't be upgraded. Especially for only $16.00!
    Attached Images Attached Images
    Last edited by dBuster; February 6th, 2011 at 01:53 PM.
    Compaq CQ60-215DX // AMD Athlon Dual Core QL-62 // 2.0 Gb Ram
    Ubuntu Lucid Lynx 10.04.2 64bit // Kernel 2.6.32-28-generic // Gnome 2.30.2
    Acer AspireONE / Lucid Lynx 10.04
    Ubuntu User #: 26559 // Linux User #: 486156

  4. #4
    Join Date
    Jul 2008
    Beans
    51

    Question Re: AWLL5088 Airlink 101 installation help

    Quote Originally Posted by dBuster View Post
    After almost giving up I decided to go to the "Supported wireless cards list and procedure to get help." thread once again and try one more time.

    Went to the wiki of supported cards and selected Airlink101. It still lists "Download kernel module sources from 'Realtek' (current filename: 'RTL8188CUS_v2.0.1212.zip'), extract to /usr/src , and run install.sh" for this super nano N usb adapter. However, after going to the Realtek page I noticed that there is a different version now available!

    NOTE THE WIKI has been updated with the new current version and the link as well.



    Link to driver: RTL8188CUS - Linux driver

    Downloaded that version and followed the directions to extract it to the /usr/src folder and then ran the install.sh and to my shock and awe the wireless adapter sprung to life!

    Sure then I had a little conflict with the internal wifi still being on and trying to keep control. Both by the way would connect and work at the same time. But for my sake of sanity I hit the wifi button on the laptop that is supposed to turn off the internal and although the light kept going the internal shut off. Now several boots later and I am solely using this new N adapter!

    I must say it is stronger to connect to my home wifi however it doesn't see as many access points in the neighborhood as the internal wifi had. Not sure why but as long as I can connect to my home setup I am ecstatic!

    So for anyone looking into the Airlink101 AWLL5088 adapter It is a great way of adding N for those who are looking at running N but have an antiquated internal card that can't be upgraded. Especially for only $16.00!
    I downloaded the driver, and put it in the usr/src directory, but I'm not sure how to install it correctly? could somebody walk me through it?

  5. #5
    Join Date
    Oct 2008
    Beans
    375
    Distro
    Ubuntu 10.04 Lucid Lynx

    Re: AWLL5088 Airlink 101 installation help

    Quote Originally Posted by ibootindos View Post
    I downloaded the driver, and put it in the usr/src directory, but I'm not sure how to install it correctly? could somebody walk me through it?
    According to the directions you were to have :

    extract to /usr/src , and run install.sh
    So you have extracted to the /usr/src folder, but have you ran install.sh file??? You may have to right click on the folder and change it to be an executable file first.

    That install script was what did the trick for me!
    Compaq CQ60-215DX // AMD Athlon Dual Core QL-62 // 2.0 Gb Ram
    Ubuntu Lucid Lynx 10.04.2 64bit // Kernel 2.6.32-28-generic // Gnome 2.30.2
    Acer AspireONE / Lucid Lynx 10.04
    Ubuntu User #: 26559 // Linux User #: 486156

  6. #6
    Join Date
    Aug 2008
    Location
    Douglasville, GA
    Beans
    130
    Distro
    Ubuntu 12.10 Quantal Quetzal

    Re: AWLL5088 Airlink 101 installation help

    Thanks to ibootindos and everyone for the solution - that worked great!

  7. #7
    Join Date
    Mar 2009
    Beans
    20
    Distro
    Ubuntu 11.04 Natty Narwhal

    Exclamation Re: AWLL5088 Airlink 101 installation help

    This doesn't work anymore with Natty

    I get this output:

    Code:
    root@RICARDO-UBUNTU:/usr/src/RTL8192CU_8188CUS_8188CE-VAU_linux_v2.0.1502.20110402# bash install.sh
    		Auto install for 8192cu
    		September, 1 2010 v 1.0.0
    rtl8192CU_linux_v2.0.1502.20110402/
    rtl8192CU_linux_v2.0.1502.20110402/autoconf_rtl8192c_usb_linux.h
    rtl8192CU_linux_v2.0.1502.20110402/clean
    rtl8192CU_linux_v2.0.1502.20110402/core/
    rtl8192CU_linux_v2.0.1502.20110402/core/efuse/
    rtl8192CU_linux_v2.0.1502.20110402/core/efuse/rtl8712_efuse.c
    rtl8192CU_linux_v2.0.1502.20110402/core/ieee80211.c
    rtl8192CU_linux_v2.0.1502.20110402/core/led/
    rtl8192CU_linux_v2.0.1502.20110402/core/led/rtl8192c_led.c
    rtl8192CU_linux_v2.0.1502.20110402/core/rtw_cmd.c
    rtl8192CU_linux_v2.0.1502.20110402/core/rtw_debug.c
    rtl8192CU_linux_v2.0.1502.20110402/core/rtw_eeprom.c
    rtl8192CU_linux_v2.0.1502.20110402/core/rtw_io.c
    rtl8192CU_linux_v2.0.1502.20110402/core/rtw_ioctl_query.c
    rtl8192CU_linux_v2.0.1502.20110402/core/rtw_ioctl_rtl.c
    rtl8192CU_linux_v2.0.1502.20110402/core/rtw_ioctl_set.c
    rtl8192CU_linux_v2.0.1502.20110402/core/rtw_mlme.c
    rtl8192CU_linux_v2.0.1502.20110402/core/rtw_mlme_ext.c
    rtl8192CU_linux_v2.0.1502.20110402/core/rtw_mp.c
    rtl8192CU_linux_v2.0.1502.20110402/core/rtw_mp_ioctl.c
    rtl8192CU_linux_v2.0.1502.20110402/core/rtw_pwrctrl.c
    rtl8192CU_linux_v2.0.1502.20110402/core/rtw_recv.c
    rtl8192CU_linux_v2.0.1502.20110402/core/rtw_rf.c
    rtl8192CU_linux_v2.0.1502.20110402/core/rtw_security.c
    rtl8192CU_linux_v2.0.1502.20110402/core/rtw_sta_mgt.c
    rtl8192CU_linux_v2.0.1502.20110402/core/rtw_wlan_util.c
    rtl8192CU_linux_v2.0.1502.20110402/core/rtw_xmit.c
    rtl8192CU_linux_v2.0.1502.20110402/hal/
    rtl8192CU_linux_v2.0.1502.20110402/hal/hal_init.c
    rtl8192CU_linux_v2.0.1502.20110402/hal/rtl8192c/
    rtl8192CU_linux_v2.0.1502.20110402/hal/rtl8192c/rtl8192c_dm.c
    rtl8192CU_linux_v2.0.1502.20110402/hal/rtl8192c/rtl8192c_phycfg.c
    rtl8192CU_linux_v2.0.1502.20110402/hal/rtl8192c/rtl8192c_rf6052.c
    rtl8192CU_linux_v2.0.1502.20110402/hal/rtl8192c/rtl8192c_rxdesc.c
    rtl8192CU_linux_v2.0.1502.20110402/hal/rtl8192c/usb/
    rtl8192CU_linux_v2.0.1502.20110402/hal/rtl8192c/usb/Hal8192CUHWImg.c
    rtl8192CU_linux_v2.0.1502.20110402/hal/rtl8192c/usb/rtl8192cu_recv.c
    rtl8192CU_linux_v2.0.1502.20110402/hal/rtl8192c/usb/rtl8192cu_xmit.c
    rtl8192CU_linux_v2.0.1502.20110402/hal/rtl8192c/usb/rtl8192c_cmd.c
    rtl8192CU_linux_v2.0.1502.20110402/hal/rtl8192c/usb/usb_halinit.c
    rtl8192CU_linux_v2.0.1502.20110402/hal/rtl8192c/usb/usb_ops_ce.c
    rtl8192CU_linux_v2.0.1502.20110402/hal/rtl8192c/usb/usb_ops_linux.c
    rtl8192CU_linux_v2.0.1502.20110402/hal/rtl8192c/usb/usb_ops_xp.c
    rtl8192CU_linux_v2.0.1502.20110402/hal/rtl8192c_d_hal_init.c
    rtl8192CU_linux_v2.0.1502.20110402/ifcfg-wlan0
    rtl8192CU_linux_v2.0.1502.20110402/include/
    rtl8192CU_linux_v2.0.1502.20110402/include/autoconf.h
    rtl8192CU_linux_v2.0.1502.20110402/include/basic_types.h
    rtl8192CU_linux_v2.0.1502.20110402/include/byteorder/
    rtl8192CU_linux_v2.0.1502.20110402/include/byteorder/big_endian.h
    rtl8192CU_linux_v2.0.1502.20110402/include/byteorder/generic.h
    rtl8192CU_linux_v2.0.1502.20110402/include/byteorder/little_endian.h
    rtl8192CU_linux_v2.0.1502.20110402/include/byteorder/swab.h
    rtl8192CU_linux_v2.0.1502.20110402/include/byteorder/swabb.h
    rtl8192CU_linux_v2.0.1502.20110402/include/circ_buf.h
    rtl8192CU_linux_v2.0.1502.20110402/include/cmd_osdep.h
    rtl8192CU_linux_v2.0.1502.20110402/include/drv_conf.h
    rtl8192CU_linux_v2.0.1502.20110402/include/drv_types.h
    rtl8192CU_linux_v2.0.1502.20110402/include/drv_types_ce.h
    rtl8192CU_linux_v2.0.1502.20110402/include/drv_types_linux.h
    rtl8192CU_linux_v2.0.1502.20110402/include/drv_types_xp.h
    rtl8192CU_linux_v2.0.1502.20110402/include/ethernet.h
    rtl8192CU_linux_v2.0.1502.20110402/include/farray.h
    rtl8192CU_linux_v2.0.1502.20110402/include/h2clbk.h
    rtl8192CU_linux_v2.0.1502.20110402/include/Hal8192CPhyCfg.h
    rtl8192CU_linux_v2.0.1502.20110402/include/Hal8192CPhyReg.h
    rtl8192CU_linux_v2.0.1502.20110402/include/Hal8192CUHWImg.h
    rtl8192CU_linux_v2.0.1502.20110402/include/HalRf.h
    rtl8192CU_linux_v2.0.1502.20110402/include/hal_init.h
    rtl8192CU_linux_v2.0.1502.20110402/include/ieee80211.h
    rtl8192CU_linux_v2.0.1502.20110402/include/ieee80211_ext.h
    rtl8192CU_linux_v2.0.1502.20110402/include/if_ether.h
    rtl8192CU_linux_v2.0.1502.20110402/include/ip.h
    rtl8192CU_linux_v2.0.1502.20110402/include/mlme_osdep.h
    rtl8192CU_linux_v2.0.1502.20110402/include/mp_custom_oid.h
    rtl8192CU_linux_v2.0.1502.20110402/include/nic_spec.h
    rtl8192CU_linux_v2.0.1502.20110402/include/osdep_ce_service.h
    rtl8192CU_linux_v2.0.1502.20110402/include/osdep_intf.h
    rtl8192CU_linux_v2.0.1502.20110402/include/osdep_service.h
    rtl8192CU_linux_v2.0.1502.20110402/include/recv_osdep.h
    rtl8192CU_linux_v2.0.1502.20110402/include/rtl8192c_cmd.h
    rtl8192CU_linux_v2.0.1502.20110402/include/rtl8192c_dm.h
    rtl8192CU_linux_v2.0.1502.20110402/include/rtl8192c_event.h
    rtl8192CU_linux_v2.0.1502.20110402/include/rtl8192c_hal.h
    rtl8192CU_linux_v2.0.1502.20110402/include/rtl8192c_recv.h
    rtl8192CU_linux_v2.0.1502.20110402/include/rtl8192c_spec.h
    rtl8192CU_linux_v2.0.1502.20110402/include/rtl8192c_xmit.h
    rtl8192CU_linux_v2.0.1502.20110402/include/rtl8712_bitdef.h
    rtl8192CU_linux_v2.0.1502.20110402/include/rtl8712_cmd.h
    rtl8192CU_linux_v2.0.1502.20110402/include/rtl8712_efuse.h
    rtl8192CU_linux_v2.0.1502.20110402/include/rtl8712_event.h
    rtl8192CU_linux_v2.0.1502.20110402/include/rtl8712_hal.h
    rtl8192CU_linux_v2.0.1502.20110402/include/rtl8712_recv.h
    rtl8192CU_linux_v2.0.1502.20110402/include/rtl8712_regdef.h
    rtl8192CU_linux_v2.0.1502.20110402/include/rtl8712_rf.h
    rtl8192CU_linux_v2.0.1502.20110402/include/rtl8712_spec.h
    rtl8192CU_linux_v2.0.1502.20110402/include/rtl8712_xmit.h
    rtl8192CU_linux_v2.0.1502.20110402/include/rtw_byteorder.h
    rtl8192CU_linux_v2.0.1502.20110402/include/rtw_cmd.h
    rtl8192CU_linux_v2.0.1502.20110402/include/rtw_debug.h
    rtl8192CU_linux_v2.0.1502.20110402/include/rtw_eeprom.h
    rtl8192CU_linux_v2.0.1502.20110402/include/rtw_event.h
    rtl8192CU_linux_v2.0.1502.20110402/include/rtw_ht.h
    rtl8192CU_linux_v2.0.1502.20110402/include/rtw_io.h
    rtl8192CU_linux_v2.0.1502.20110402/include/rtw_ioctl.h
    rtl8192CU_linux_v2.0.1502.20110402/include/rtw_ioctl_query.h
    rtl8192CU_linux_v2.0.1502.20110402/include/rtw_ioctl_rtl.h
    rtl8192CU_linux_v2.0.1502.20110402/include/rtw_ioctl_set.h
    rtl8192CU_linux_v2.0.1502.20110402/include/rtw_led.h
    rtl8192CU_linux_v2.0.1502.20110402/include/rtw_mlme.h
    rtl8192CU_linux_v2.0.1502.20110402/include/rtw_mlme_ext.h
    rtl8192CU_linux_v2.0.1502.20110402/include/rtw_mp.h
    rtl8192CU_linux_v2.0.1502.20110402/include/rtw_mp_ioctl.h
    rtl8192CU_linux_v2.0.1502.20110402/include/rtw_mp_phy_regdef.h
    rtl8192CU_linux_v2.0.1502.20110402/include/rtw_pwrctrl.h
    rtl8192CU_linux_v2.0.1502.20110402/include/rtw_qos.h
    rtl8192CU_linux_v2.0.1502.20110402/include/rtw_recv.h
    rtl8192CU_linux_v2.0.1502.20110402/include/rtw_rf.h
    rtl8192CU_linux_v2.0.1502.20110402/include/rtw_security.h
    rtl8192CU_linux_v2.0.1502.20110402/include/rtw_version.h
    rtl8192CU_linux_v2.0.1502.20110402/include/rtw_xmit.h
    rtl8192CU_linux_v2.0.1502.20110402/include/sdio_hal.h
    rtl8192CU_linux_v2.0.1502.20110402/include/sdio_ops.h
    rtl8192CU_linux_v2.0.1502.20110402/include/sdio_ops_ce.h
    rtl8192CU_linux_v2.0.1502.20110402/include/sdio_ops_linux.h
    rtl8192CU_linux_v2.0.1502.20110402/include/sdio_ops_xp.h
    rtl8192CU_linux_v2.0.1502.20110402/include/sdio_osintf.h
    rtl8192CU_linux_v2.0.1502.20110402/include/sta_info.h
    rtl8192CU_linux_v2.0.1502.20110402/include/usb_hal.h
    rtl8192CU_linux_v2.0.1502.20110402/include/usb_ops.h
    rtl8192CU_linux_v2.0.1502.20110402/include/usb_osintf.h
    rtl8192CU_linux_v2.0.1502.20110402/include/usb_vendor_req.h
    rtl8192CU_linux_v2.0.1502.20110402/include/version.h
    rtl8192CU_linux_v2.0.1502.20110402/include/wifi.h
    rtl8192CU_linux_v2.0.1502.20110402/include/wlan_bssdef.h
    rtl8192CU_linux_v2.0.1502.20110402/include/xmit_osdep.h
    rtl8192CU_linux_v2.0.1502.20110402/Kconfig
    rtl8192CU_linux_v2.0.1502.20110402/Makefile
    rtl8192CU_linux_v2.0.1502.20110402/os_dep/
    rtl8192CU_linux_v2.0.1502.20110402/os_dep/linux/
    rtl8192CU_linux_v2.0.1502.20110402/os_dep/linux/ioctl_linux.c
    rtl8192CU_linux_v2.0.1502.20110402/os_dep/linux/mlme_linux.c
    rtl8192CU_linux_v2.0.1502.20110402/os_dep/linux/os_intfs.c
    rtl8192CU_linux_v2.0.1502.20110402/os_dep/linux/recv_linux.c
    rtl8192CU_linux_v2.0.1502.20110402/os_dep/linux/sdio_intf.c
    rtl8192CU_linux_v2.0.1502.20110402/os_dep/linux/usb_intf.c
    rtl8192CU_linux_v2.0.1502.20110402/os_dep/linux/xmit_linux.c
    rtl8192CU_linux_v2.0.1502.20110402/os_dep/osdep_service.c
    rtl8192CU_linux_v2.0.1502.20110402/runwpa
    rtl8192CU_linux_v2.0.1502.20110402/wlan0dhcp
    rtl8192CU_linux_v2.0.1502.20110402/wpa1.conf
    rtl8192CU_linux_v2.0.1502.20110402
    Authentication requested [root] for make driver:
    make ARCH=x86_64 CROSS_COMPILE= -C /lib/modules/2.6.38-8-generic/build M=/usr/src/RTL8192CU_8188CUS_8188CE-VAU_linux_v2.0.1502.20110402/driver/rtl8192CU_linux_v2.0.1502.20110402  modules
    make[1]: Entering directory `/usr/src/linux-headers-2.6.38-8-generic'
      CC [M]  /usr/src/RTL8192CU_8188CUS_8188CE-VAU_linux_v2.0.1502.20110402/driver/rtl8192CU_linux_v2.0.1502.20110402/core/rtw_cmd.o
      CC [M]  /usr/src/RTL8192CU_8188CUS_8188CE-VAU_linux_v2.0.1502.20110402/driver/rtl8192CU_linux_v2.0.1502.20110402/core/rtw_security.o
      CC [M]  /usr/src/RTL8192CU_8188CUS_8188CE-VAU_linux_v2.0.1502.20110402/driver/rtl8192CU_linux_v2.0.1502.20110402/core/rtw_debug.o
      CC [M]  /usr/src/RTL8192CU_8188CUS_8188CE-VAU_linux_v2.0.1502.20110402/driver/rtl8192CU_linux_v2.0.1502.20110402/core/rtw_io.o
      CC [M]  /usr/src/RTL8192CU_8188CUS_8188CE-VAU_linux_v2.0.1502.20110402/driver/rtl8192CU_linux_v2.0.1502.20110402/core/rtw_ioctl_query.o
      CC [M]  /usr/src/RTL8192CU_8188CUS_8188CE-VAU_linux_v2.0.1502.20110402/driver/rtl8192CU_linux_v2.0.1502.20110402/core/rtw_ioctl_set.o
      CC [M]  /usr/src/RTL8192CU_8188CUS_8188CE-VAU_linux_v2.0.1502.20110402/driver/rtl8192CU_linux_v2.0.1502.20110402/core/ieee80211.o
      CC [M]  /usr/src/RTL8192CU_8188CUS_8188CE-VAU_linux_v2.0.1502.20110402/driver/rtl8192CU_linux_v2.0.1502.20110402/core/rtw_mlme.o
      CC [M]  /usr/src/RTL8192CU_8188CUS_8188CE-VAU_linux_v2.0.1502.20110402/driver/rtl8192CU_linux_v2.0.1502.20110402/core/rtw_mlme_ext.o
      CC [M]  /usr/src/RTL8192CU_8188CUS_8188CE-VAU_linux_v2.0.1502.20110402/driver/rtl8192CU_linux_v2.0.1502.20110402/core/rtw_wlan_util.o
      CC [M]  /usr/src/RTL8192CU_8188CUS_8188CE-VAU_linux_v2.0.1502.20110402/driver/rtl8192CU_linux_v2.0.1502.20110402/core/rtw_pwrctrl.o
      CC [M]  /usr/src/RTL8192CU_8188CUS_8188CE-VAU_linux_v2.0.1502.20110402/driver/rtl8192CU_linux_v2.0.1502.20110402/core/rtw_rf.o
      CC [M]  /usr/src/RTL8192CU_8188CUS_8188CE-VAU_linux_v2.0.1502.20110402/driver/rtl8192CU_linux_v2.0.1502.20110402/core/rtw_recv.o
      CC [M]  /usr/src/RTL8192CU_8188CUS_8188CE-VAU_linux_v2.0.1502.20110402/driver/rtl8192CU_linux_v2.0.1502.20110402/core/rtw_sta_mgt.o
      CC [M]  /usr/src/RTL8192CU_8188CUS_8188CE-VAU_linux_v2.0.1502.20110402/driver/rtl8192CU_linux_v2.0.1502.20110402/core/rtw_xmit.o
      CC [M]  /usr/src/RTL8192CU_8188CUS_8188CE-VAU_linux_v2.0.1502.20110402/driver/rtl8192CU_linux_v2.0.1502.20110402/core/efuse/rtl8712_efuse.o
      CC [M]  /usr/src/RTL8192CU_8188CUS_8188CE-VAU_linux_v2.0.1502.20110402/driver/rtl8192CU_linux_v2.0.1502.20110402/core/led/rtl8192c_led.o
      CC [M]  /usr/src/RTL8192CU_8188CUS_8188CE-VAU_linux_v2.0.1502.20110402/driver/rtl8192CU_linux_v2.0.1502.20110402/hal/hal_init.o
      CC [M]  /usr/src/RTL8192CU_8188CUS_8188CE-VAU_linux_v2.0.1502.20110402/driver/rtl8192CU_linux_v2.0.1502.20110402/hal/rtl8192c_d_hal_init.o
      CC [M]  /usr/src/RTL8192CU_8188CUS_8188CE-VAU_linux_v2.0.1502.20110402/driver/rtl8192CU_linux_v2.0.1502.20110402/hal/rtl8192c/rtl8192c_phycfg.o
      CC [M]  /usr/src/RTL8192CU_8188CUS_8188CE-VAU_linux_v2.0.1502.20110402/driver/rtl8192CU_linux_v2.0.1502.20110402/hal/rtl8192c/rtl8192c_rf6052.o
      CC [M]  /usr/src/RTL8192CU_8188CUS_8188CE-VAU_linux_v2.0.1502.20110402/driver/rtl8192CU_linux_v2.0.1502.20110402/hal/rtl8192c/rtl8192c_dm.o
      CC [M]  /usr/src/RTL8192CU_8188CUS_8188CE-VAU_linux_v2.0.1502.20110402/driver/rtl8192CU_linux_v2.0.1502.20110402/hal/rtl8192c/rtl8192c_rxdesc.o
      CC [M]  /usr/src/RTL8192CU_8188CUS_8188CE-VAU_linux_v2.0.1502.20110402/driver/rtl8192CU_linux_v2.0.1502.20110402/hal/rtl8192c/usb/usb_ops_linux.o
      CC [M]  /usr/src/RTL8192CU_8188CUS_8188CE-VAU_linux_v2.0.1502.20110402/driver/rtl8192CU_linux_v2.0.1502.20110402/hal/rtl8192c/usb/usb_halinit.o
      CC [M]  /usr/src/RTL8192CU_8188CUS_8188CE-VAU_linux_v2.0.1502.20110402/driver/rtl8192CU_linux_v2.0.1502.20110402/hal/rtl8192c/usb/Hal8192CUHWImg.o
      CC [M]  /usr/src/RTL8192CU_8188CUS_8188CE-VAU_linux_v2.0.1502.20110402/driver/rtl8192CU_linux_v2.0.1502.20110402/hal/rtl8192c/usb/rtl8192cu_xmit.o
      CC [M]  /usr/src/RTL8192CU_8188CUS_8188CE-VAU_linux_v2.0.1502.20110402/driver/rtl8192CU_linux_v2.0.1502.20110402/hal/rtl8192c/usb/rtl8192cu_recv.o
      CC [M]  /usr/src/RTL8192CU_8188CUS_8188CE-VAU_linux_v2.0.1502.20110402/driver/rtl8192CU_linux_v2.0.1502.20110402/hal/rtl8192c/usb/rtl8192c_cmd.o
    /usr/src/RTL8192CU_8188CUS_8188CE-VAU_linux_v2.0.1502.20110402/driver/rtl8192CU_linux_v2.0.1502.20110402/hal/rtl8192c/usb/rtl8192c_cmd.c: In function ‘SetFwRsvdPagePkt’:
    /usr/src/RTL8192CU_8188CUS_8188CE-VAU_linux_v2.0.1502.20110402/driver/rtl8192CU_linux_v2.0.1502.20110402/hal/rtl8192c/usb/rtl8192c_cmd.c:2105:3: warning: format ‘%d’ expects type ‘int’, but argument 2 has type ‘long unsigned int’
    /usr/src/RTL8192CU_8188CUS_8188CE-VAU_linux_v2.0.1502.20110402/driver/rtl8192CU_linux_v2.0.1502.20110402/hal/rtl8192c/usb/rtl8192c_cmd.c: In function ‘set_FwJoinBssReport_cmd’:
    /usr/src/RTL8192CU_8188CUS_8188CE-VAU_linux_v2.0.1502.20110402/driver/rtl8192CU_linux_v2.0.1502.20110402/hal/rtl8192c/usb/rtl8192c_cmd.c:2184:2: warning: format ‘%d’ expects type ‘int’, but argument 3 has type ‘long unsigned int’
      CC [M]  /usr/src/RTL8192CU_8188CUS_8188CE-VAU_linux_v2.0.1502.20110402/driver/rtl8192CU_linux_v2.0.1502.20110402/os_dep/osdep_service.o
      CC [M]  /usr/src/RTL8192CU_8188CUS_8188CE-VAU_linux_v2.0.1502.20110402/driver/rtl8192CU_linux_v2.0.1502.20110402/os_dep/linux/os_intfs.o
      CC [M]  /usr/src/RTL8192CU_8188CUS_8188CE-VAU_linux_v2.0.1502.20110402/driver/rtl8192CU_linux_v2.0.1502.20110402/os_dep/linux/usb_intf.o
    /usr/src/RTL8192CU_8188CUS_8188CE-VAU_linux_v2.0.1502.20110402/driver/rtl8192CU_linux_v2.0.1502.20110402/os_dep/linux/usb_intf.c: In function ‘rtw_drv_init’:
    /usr/src/RTL8192CU_8188CUS_8188CE-VAU_linux_v2.0.1502.20110402/driver/rtl8192CU_linux_v2.0.1502.20110402/os_dep/linux/usb_intf.c:1038:23: error: ‘struct usb_device’ has no member named ‘autosuspend_delay’
    make[2]: *** [/usr/src/RTL8192CU_8188CUS_8188CE-VAU_linux_v2.0.1502.20110402/driver/rtl8192CU_linux_v2.0.1502.20110402/os_dep/linux/usb_intf.o] Error 1
    make[1]: *** [_module_/usr/src/RTL8192CU_8188CUS_8188CE-VAU_linux_v2.0.1502.20110402/driver/rtl8192CU_linux_v2.0.1502.20110402] Error 2
    make[1]: Leaving directory `/usr/src/linux-headers-2.6.38-8-generic'
    make: *** [modules] Error 2
    Compile make driver error: 2, Please check error Mesg
    Last edited by ralfarof; May 3rd, 2011 at 12:24 AM.

  8. #8
    Join Date
    Mar 2009
    Beans
    20
    Distro
    Ubuntu 11.04 Natty Narwhal

    Re: AWLL5088 Airlink 101 installation help

    I send an email to Realtek support, if I get an answer I'll post it here.

  9. #9
    Join Date
    Oct 2007
    Beans
    161
    Distro
    Ubuntu

    Re: AWLL5088 Airlink 101 installation help

    dBuster, did you get this working on 32-bit or 64-bit? I'm having a hard time finding a mini usb wifi adapter that will work on 64-bit. Last one I bought worked great on 32-bit, but is all sorts of fail on 64-bit, unfortunately.

    ralfarof, Natty (and its 2.6.38 kernel) have made changes that cause old drivers to fail the build process -- if you have the know-how, you can probably hunt the errors down and get it to build, but it's not easy :/

  10. #10
    Join Date
    Oct 2006
    Beans
    Hidden!

    Re: AWLL5088 Airlink 101 installation help

    Onieric Driver:AWLL5088 Onieric 32/64bit v3.0.2590 Driver

    The latest sources from Realtek will compile for Natty.
    The driver package is for RTL8188CUS.
    Realtek wireless NIC Drivers

    OR

    Below is link to latest driver package that will automatically update with each new kernel update.
    Link to driver:Airlink AWLL5088 Natty 32/64bit v3.0.2164 Driver
    Previous Versions:
    version 2.0.1502
    version 3.0.1590


    Driver automatically updates for each kernel.
    You have to install dkms and header packages, first.

    (Be sure to substitute file name below with the version you downloaded.)

    sudo apt-get install dkms linux-headers-generic
    tar xvf Airlink_AWLL5088_Natty_Driver-v_3.0.2164.tar.gz
    cd Airlink_AWLL5088_Natty_Driver-v_3.0.2164/
    ./install-with-dkms.sh

    To remove from dkms use:
    ./remove-from-dkms.sh

    The install.sh script from "Realtek" still works but wont recompile autmatically for each new kernel.
    Last edited by freewindster; November 6th, 2011 at 05:48 PM.

Page 1 of 5 123 ... LastLast

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •