I launched a Amazon Instance using ami-4a0df923 last night and installed vsftpd on it. But i am unable to connect using PASV mode. Following containing everything i could dig in.
commandline FTP Output:
Code:
230 Login successful.
Remote system type is UNIX.
Using binary mode to transfer files.
ftp> ls /
227 Entering Passive Mode (84,173,63,172,47,47).
ftp: connect: Connection timed out
ftp> 221 Goodbye.
FileZilla's Output:
Code:
13:51:42 Status: Connection established, waiting for welcome message...
13:51:42 Response: 220 (vsFTPd 2.2.2)
13:51:42 Command: USER fsftp
13:51:43 Response: 331 Please specify the password.
13:51:43 Command: PASS ****************
13:51:44 Response: 230 Login successful.
13:51:44 Command: OPTS UTF8 ON
13:51:44 Response: 200 Always in UTF8 mode.
13:51:44 Status: Connected
13:51:44 Status: Retrieving directory listing...
13:51:44 Command: PWD
13:51:44 Response: 257 "/"
13:51:44 Command: TYPE I
13:51:45 Response: 200 Switching to Binary mode.
13:51:45 Command: PASV
13:51:45 Response: 227 Entering Passive Mode (84,173,63,172,47,23).
13:51:45 Command: LIST
13:52:46 Response: 425 Failed to establish connection.
13:52:46 Error: Failed to retrieve directory listing
IPtables:
Code:
# iptables -nvL
Chain INPUT (policy ACCEPT 1099 packets, 104K bytes)
pkts bytes target prot opt in out source destination
Chain FORWARD (policy ACCEPT 0 packets, 0 bytes)
pkts bytes target prot opt in out source destination
Chain OUTPUT (policy ACCEPT 1061 packets, 228K bytes)
pkts bytes target prot opt in out source destination
Amazon's Security Group:
Code:
All:icmp:-1:-1:0.0.0.0/0
FTP:tcp:21:21:0.0.0.0/0
SSH:tcp:22:22:0.0.0.0/0
HTTPS:tcp:443:443:0.0.0.0/0
HTTP:tcp:80:80:0.0.0.0/0
vsftpd.conf:
Code:
$ cat /etc/vsftpd.conf
# Example config file /etc/vsftpd.conf
#
# The default compiled in settings are fairly paranoid. This sample file
# loosens things up a bit, to make the ftp daemon more usable.
# Please see vsftpd.conf.5 for all compiled in defaults.
#
# READ THIS: This example file is NOT an exhaustive list of vsftpd options.
# Please read the vsftpd.conf.5 manual page to get a full idea of vsftpd's
# capabilities.
#
#
# Run standalone? vsftpd can run either from an inetd or as a standalone
# daemon started from an initscript.
listen=YES
#listen_address=84.173.63.172
#
# Run standalone with IPv6?
# Like the listen parameter, except vsftpd will listen on an IPv6 socket
# instead of an IPv4 one. This parameter and the listen parameter are mutually
# exclusive.
#listen_ipv6=YES
#
# Allow anonymous FTP? (Disabled by default)
anonymous_enable=NO
#
# Uncomment this to allow local users to log in.
local_enable=YES
#
# Uncomment this to enable any form of FTP write command.
write_enable=YES
#
# Default umask for local users is 077. You may wish to change this to 022,
# if your users expect that (022 is used by most other ftpd's)
#local_umask=022
#
# Uncomment this to allow the anonymous FTP user to upload files. This only
# has an effect if the above global write enable is activated. Also, you will
# obviously need to create a directory writable by the FTP user.
#anon_upload_enable=YES
#
# Uncomment this if you want the anonymous FTP user to be able to create
# new directories.
#anon_mkdir_write_enable=YES
#
# Activate directory messages - messages given to remote users when they
# go into a certain directory.
dirmessage_enable=YES
#
# If enabled, vsftpd will display directory listings with the time
# in your local time zone. The default is to display GMT. The
# times returned by the MDTM FTP command are also affected by this
# option.
use_localtime=YES
#
# Activate logging of uploads/downloads.
xferlog_enable=YES
#
# Make sure PORT transfer connections originate from port 20 (ftp-data).
connect_from_port_20=YES
#
# If you want, you can arrange for uploaded anonymous files to be owned by
# a different user. Note! Using "root" for uploaded files is not
# recommended!
#chown_uploads=YES
#chown_username=whoever
#
# You may override where the log file goes if you like. The default is shown
# below.
xferlog_file=/var/log/vsftpd.log
#
# If you want, you can have your log file in standard ftpd xferlog format.
# Note that the default log file location is /var/log/xferlog in this case.
#xferlog_std_format=YES
#
# You may change the default value for timing out an idle session.
idle_session_timeout=600
#
# You may change the default value for timing out a data connection.
data_connection_timeout=120
#
# It is recommended that you define on your system a unique user which the
# ftp server can use as a totally isolated and unprivileged user.
#nopriv_user=ftpsecure
#
# Enable this and the server will recognise asynchronous ABOR requests. Not
# recommended for security (the code is non-trivial). Not enabling it,
# however, may confuse older FTP clients.
#async_abor_enable=YES
#
# By default the server will pretend to allow ASCII mode but in fact ignore
# the request. Turn on the below options to have the server actually do ASCII
# mangling on files when in ASCII mode.
# Beware that on some FTP servers, ASCII support allows a denial of service
# attack (DoS) via the command "SIZE /big/file" in ASCII mode. vsftpd
# predicted this attack and has always been safe, reporting the size of the
# raw file.
# ASCII mangling is a horrible feature of the protocol.
#ascii_upload_enable=YES
#ascii_download_enable=YES
#
# You may fully customise the login banner string:
#ftpd_banner=Welcome to blah FTP service.
#
# You may specify a file of disallowed anonymous e-mail addresses. Apparently
# useful for combatting certain DoS attacks.
#deny_email_enable=YES
# (default follows)
#banned_email_file=/etc/vsftpd.banned_emails
#
# You may restrict local users to their home directories. See the FAQ for
# the possible risks in this before using chroot_local_user or
# chroot_list_enable below.
chroot_local_user=YES
#
# You may specify an explicit list of local users to chroot() to their home
# directory. If chroot_local_user is YES, then this list becomes a list of
# users to NOT chroot().
#chroot_local_user=YES
chroot_list_enable=NO
# (default follows)
#chroot_list_file=/etc/vsftpd.chroot_list
#
# You may activate the "-R" option to the builtin ls. This is disabled by
# default to avoid remote users being able to cause excessive I/O on large
# sites. However, some broken FTP clients such as "ncftp" and "mirror" assume
# the presence of the "-R" option, so there is a strong case for enabling it.
#ls_recurse_enable=YES
#
# Debian customization
#
# Some of vsftpd's settings don't fit the Debian filesystem layout by
# default. These settings are more Debian-friendly.
#
# This option should be the name of a directory which is empty. Also, the
# directory should not be writable by the ftp user. This directory is used
# as a secure chroot() jail at times vsftpd does not require filesystem
# access.
secure_chroot_dir=/var/run/vsftpd/empty
#
# This string is the name of the PAM service vsftpd will use.
pam_service_name=vsftpd
#
# This option specifies the location of the RSA certificate to use for SSL
# encrypted connections.
#rsa_cert_file=/etc/ssl/private/vsftpd.pem
userlist_deny=NO
userlist_enable=YES
userlist_file=/etc/vsftpd.allowed_users
# Show hidden files and the "." and ".." folders.
# Useful to not write over hidden files:
force_dot_files=YES
# Hide the info about the owner (user and group) of the files.
hide_ids=YES
# PASV configurations
pasv_promiscuous=YES
pasv_enable=YES
pasv_min_port=12000
pasv_max_port=12100
pasv_address=84.173.63.172
/etc/vsftpd.allowed_users
Solution:
Allow 12000-12100 inside Amazon Security Group Settings
thanks to http://www.gosquared.com/liquidicity/archives/936
Adv Reply
Bookmarks