Page 1 of 2 12 LastLast
Results 1 to 10 of 145

Thread: Rosewill RNX-N150PC PCI Ralink 3060 chip driver instructions

Hybrid View

  1. #1
    Join Date
    Jul 2009
    Location
    Dayton Ohio USA
    Beans
    1,070
    Distro
    Ubuntu 13.04 Raring Ringtail

    Rosewill RNX-N150PC PCI Ralink 3060 chip driver instructions

    This is the procedure I used to install the driver for my new Rosewill Rosewill RNX-N150PC PCI 2.2 Wireless Adapter. It uses the Ralink 3060 chip. I'm using Lucid 10.04 and WICD as my network manager.(I have tested this driver and method on both 10.10 & currently 11.04 with success) I downloaded the drivers from Ralinks site
    http://www.ralinktech.com/license_us...V3TVRJeE53PT1D

    Make sure you have installed gcc build-essential
    Code:
    sudo apt-get install gcc build-essential
    I then followed the instuctions in the README file.
    Navigate to downloaded_driver_folder/os/linux and open config.mk in a text editor.
    Find and set so that it indicates ( y ) at the end of this text string
    Code:
    HAS_WPA_SUPPLICANT=y
    and also set
    Code:
    HAS_NATIVE_WPA_SUPPLICANT_SUPPORT=y
    Next, open a terminal in the driver folder and type
    Code:
    sudo make
    then
    Code:
    sudo make install

    Now you'll need to load the driver
    Code:
    sudo modprobe rt3562sta
    Code:
    sudo ifconfig ra0 inet up

    After I successfully connected I added the driver to /etc/modules so it it would load at startup. This is a copy of mine

    Code:
     # /etc/modules: kernel modules to load at boot time.
    #
    # This file contains the names of kernel modules that should be loaded
    # at boot time, one per line. Lines beginning with "#" are ignored.
    
    loop
    lp
    rt3562sta.ko
    Edit complete save file and reboot to test. I hope this helps anyone using Raklink 3060/3062/3562 chipset. Mine connects with a strong consistent signal.

    Looks as if an addition is necessary to complete the driver install. The need to blacklist a default driver to enable the new driver.
    From terminal
    Code:
    gksu gedit /etc/modprobe.d/blacklist.conf
    Add this to the end of that file
    Code:
    blacklist rt2800pci
    Last edited by MooPi; June 26th, 2011 at 04:35 PM.
    It's okay, I'm a limo driver

  2. #2
    Join Date
    Sep 2010
    Beans
    11

    Re: Rosewill RNX-N150PC PCI Ralink 3060 chip driver instructions

    I used this driver in 10.04 and it worked fine.
    But now I use 10.10, and although the driver is running - both Wicd and Network Manager can't find any networks.

  3. #3
    Join Date
    Jul 2009
    Location
    Dayton Ohio USA
    Beans
    1,070
    Distro
    Ubuntu 13.04 Raring Ringtail

    Re: Rosewill RNX-N150PC PCI Ralink 3060 chip driver instructions

    Quote Originally Posted by Shualdon View Post
    I used this driver in 10.04 and it worked fine.
    But now I use 10.10, and although the driver is running - both Wicd and Network Manager can't find any networks.
    I haven't tested under 10.10 yet. What have you done so far to get the device working ?
    It's okay, I'm a limo driver

  4. #4
    Join Date
    Sep 2010
    Beans
    11

    Re: Rosewill RNX-N150PC PCI Ralink 3060 chip driver instructions

    Quote Originally Posted by MooPi View Post
    I haven't tested under 10.10 yet. What have you done so far to get the device working ?
    I use my brother's USB wireless adapter which has a built-in support...

  5. #5
    Join Date
    Jul 2009
    Location
    Dayton Ohio USA
    Beans
    1,070
    Distro
    Ubuntu 13.04 Raring Ringtail

    Re: Rosewill RNX-N150PC PCI Ralink 3060 chip driver instructions

    No what have you done to get your Ralink device working ?
    How about we try some terminal commands to see what comes up.
    Code:
    lspci -v | less
    Code:
    iwconfig
    If you show a network in the last command run this.
    Code:
    iwlist scanning
    Post any results back here please
    It's okay, I'm a limo driver

  6. #6
    Join Date
    Sep 2010
    Beans
    11

    Re: Rosewill RNX-N150PC PCI Ralink 3060 chip driver instructions

    I have Edimax EW-7711In (PCI).
    It shows up in ifconfig, but that's it.

    lspci -v (only the related part)
    Code:
    05:02.0 Network controller: RaLink Device 3060
            Subsystem: Edimax Computer Co. Device 7711
            Flags: bus master, slow devsel, latency 32, IRQ 18
            Memory at fbcf0000 (32-bit, non-prefetchable) [size=64K]
            Capabilities: <access denied>
            Kernel driver in use: rt2800pci
            Kernel modules: rt3562sta, rt2800pci
    iwconfig (wlan2 is the Ralink, wlan1 is the USB)
    Code:
    lo        no wireless extensions.
    
    eth1      no wireless extensions.
    
    wlan2     IEEE 802.11bgn  ESSID:off/any  
              Mode:Managed  Access Point: Not-Associated   Tx-Power=20 dBm   
              Retry  long limit:7   RTS thr:off   Fragment thr:off
              Power Management:off
              
    vboxnet0  no wireless extensions.
    
    wlan1     IEEE 802.11bg  ESSID:"confidential"  
              Mode:Managed  Frequency:2.437 GHz  Access Point: 00:22:B0:72:9A:BD   
              Bit Rate=54 Mb/s   Tx-Power=7 dBm   
              Retry  long limit:7   RTS thr:off   Fragment thr:off
              Power Management:on
              Link Quality=56/70  Signal level=-54 dBm  
              Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
              Tx excessive retries:0  Invalid misc:0   Missed beacon:0
    iwlist scanning
    Code:
    lo        Interface doesn't support scanning.
    
    eth1      Interface doesn't support scanning.
    
    wlan2     No scan results
    
    vboxnet0  Interface doesn't support scanning.
    
    wlan1     Scan completed :
              Cell 01 - Address: 00:22:B0:72:9A:BD
                        Channel:6
                        Frequency:2.437 GHz (Channel 6)
                        Quality=56/70  Signal level=-54 dBm  
                        Encryption key:off
                        ESSID:"confidential"
                        Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s
                                  24 Mb/s; 36 Mb/s; 54 Mb/s
                        Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 48 Mb/s
                        Mode:Master
                        Extra:tsf=000002ea5a89e570
                        Extra: Last beacon: 19568ms ago
                        IE: Unknown: 00096162617262616E656C
                        IE: Unknown: 010882848B962430486C
                        IE: Unknown: 030106
                        IE: Unknown: 2A0100
                        IE: Unknown: 2F0100
                        IE: Unknown: 32040C121860
                        IE: Unknown: DD090010180202F0000000
                        IE: Unknown: DD180050F2020101800003A4000027A4000042435E0062322F00

  7. #7
    Join Date
    Dec 2008
    Location
    South Lake Tahoe, CA
    Beans
    31
    Distro
    Kubuntu 8.04 Hardy Heron

    Re: Rosewill RNX-N150PC PCI Ralink 3060 chip driver instructions

    Hello!
    I am trying to get my Rosewill RNX N150pcx installed in 10.04lts. I got to the 5th step: Now you'll need to load the driver

    Code:
    sudo modprobe rt3562sta.ko

    these commands just result in: FATAL Module rt3562sta.ko not found

    lspci shows a network controller at 02:09.0 RaLink Device 3060 etc...

    the funny thing is when I opened Hardware Drivers rt3562sta.ko was there. it says the driver is activated but not currently in use. So I deactivated it. then reactivated it. It worked! I connected to my wireless router.

    BUT... after reboot no such luck. the driver still says its active but not in use. but if i disable/reable, it just asks for reboot and I am back to where i started.(no connection)
    And I did add the lines to /etc/modules and saved it....

    One Note, Make Install required sudo privledges. but i did not use it on the Make Command.....

    Thanks for the help!

    Jazz

  8. #8
    Join Date
    Jul 2007
    Beans
    9

    Re: Rosewill RNX-N150PC PCI Ralink 3060 chip driver instructions

    Quote Originally Posted by MooPi View Post
    This is the procedure I used to install the driver for my new Rosewill Rosewill RNX-N150PC PCI 2.2 Wireless Adapter. It uses the Ralink 3060 chip. I'm using Lucid 10.04 and WICD as my network manager.(I have tested this driver and method on both 10.10 & currently 11.04 with success) I downloaded the drivers from Ralinks site
    http://www.ralinktech.com/license_us...V3TVRJeE53PT1D

    Make sure you have installed gcc build-essential
    Code:
    sudo apt-get install gcc build-essential
    I then followed the instuctions in the README file.
    Navigate to downloaded_driver_folder/os/linux and open config.mk in a text editor.
    Find and set so that it indicates ( y ) at the end of this text string
    Code:
    HAS_WPA_SUPPLICANT=y
    and also set
    Code:
    HAS_NATIVE_WPA_SUPPLICANT_SUPPORT=y
    Next, open a terminal in the driver folder and type
    Code:
    sudo make
    then
    Code:
    sudo make install

    Now you'll need to load the driver
    Code:
    sudo modprobe rt3562sta
    Code:
    sudo ifconfig ra0 inet up

    After I successfully connected I added the driver to /etc/modules so it it would load at startup. This is a copy of mine

    Code:
     # /etc/modules: kernel modules to load at boot time.
    #
    # This file contains the names of kernel modules that should be loaded
    # at boot time, one per line. Lines beginning with "#" are ignored.
    
    loop
    lp
    rt3562sta.ko
    Edit complete save file and reboot to test. I hope this helps anyone using Raklink 3060/3062/3562 chipset. Mine connects with a strong consistent signal.

    Looks as if an addition is necessary to complete the driver install. The need to blacklist a default driver to enable the new driver.
    From terminal
    Code:
    gksu gedit /etc/modprobe.d/blacklist.conf
    Add this to the end of that file
    Code:
    blacklist rt2800pci
    Tried doing this in 11.04, unfortauntly when i get to "sudo ifconfig ra0 inet up" it reports "SIOCSIFFLAGS: Operation not permitted"

    Any help for this?

    *also, under lspci is shows up as "01:00.0 Unclassified device (0080): Ralink corp. Device 3060

    apparently "sudo service networking restart should fix this but it doesnt, and ra0 doesnt show up under ifconfig, but it does show up under iwconfig.
    Last edited by Midnitte; August 30th, 2011 at 06:00 PM.

  9. #9
    Join Date
    Jul 2007
    Beans
    9

    Re: Rosewill RNX-N150PC PCI Ralink 3060 chip driver instructions

    bump? D:

  10. #10
    Join Date
    Jan 2010
    Location
    Portland, Oregon
    Beans
    51
    Distro
    Ubuntu 12.04 Precise Pangolin

    Re: Rosewill RNX-N150PC PCI Ralink 3060 chip driver instructions

    Quote Originally Posted by Midnitte View Post
    Tried doing this in 11.04, unfortauntly when i get to "sudo ifconfig ra0 inet up" it reports "SIOCSIFFLAGS: Operation not permitted"

    Any help for this?

    *also, under lspci is shows up as "01:00.0 Unclassified device (0080): Ralink corp. Device 3060

    apparently "sudo service networking restart should fix this but it doesnt, and ra0 doesnt show up under ifconfig, but it does show up under iwconfig.
    post output of these commands and we'll see where you're at.

    Code:
    lsmod
    sudo lshw -C network
    iwconfig

Page 1 of 2 12 LastLast

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •