hello everybody. new to linux and loving it. terminal tells me i have this wireless card:
03:00.0 Network controller : Broadcom Corporation BCM4312 802.11b/g LP-PHY [14e4:4315] (rev 01)
i would like to use aircrack, and although the instructions on the first page seem detailed enough, i'm wondering how much has changed since it was written, as my kernel is the latest (2.6.35-24).
my biggest concern is messing up my wireless card by not blacklisting wl, as mentioned in the beginning of this thread. is this still necessary to do? and if so, how do i do it? i've googled for it, but i haven't yet found instructions on how to blacklist wl.
since there have been changes to the kernel/drivers, are the original instructions still relevant, or is there an updated version?
sorry if this has been asked before, but 83 pages is a lot to read. i simply don't have the time.
I used to own a notebook with this card. My success was found by installing bcmwl with synaptic, allowing wl dkms to load at boot, then modprobe b43. This method worked well.
i don't understand what it means to allow wl dkms to load at boot, then modprobe b43. will it be obvious to see wl dkms load at boot, and is modprobe b43 a terminal command? sry if this is an utterly stupid question. i'm just learning. thanks
I installed the wl dkms with
I then installed the firmware withCode:sudo apt-get install bcmwl-kernel-source
After reboot, load the b43 module withCode:sudo apt-get install b43-fwcutter
eth1 is the interface the wl module usesCode:sudo modprobe b43
wlan0 is the interface the b43 module uses
also more info about the wl dkms can be found @ http://packages.ubuntu.com/lucid/bcmwl-kernel-source
more info about the b43 module can be found @ http://wireless.kernel.org/en/users/Drivers/b43
You must allow the wl dkms module to load first if you want the b43 module to load without errors. Hope this helps you. If not you could download Secmic 4.04 or 4.10 @ http://secmic.org as it includes b43 preloaded.
Last edited by rlelliott; December 17th, 2010 at 10:37 AM.
thanks for the detailed instructions mate, i would have never guessed to do that on my own.
now, once i complete these steps, i may proceed with the instructions from page 1?
i'm still wondering if somewhere within the 83 pages of this thread, and over the years, if an updated version of those instructions has been posted.
If you read through the pages of this Topic, you should gain a good working knowledge of how wireless card modules are built and loaded and a good base of how most modules work in Linux.
To answer your question, if you follow my instructions you will not need to use the ones posted on the main page. The steps listed there are more advanced and allow you to load b43 standalone without first loading wl.
Also you may want to create a script that loads b43, unloads b43, loads wl, and unloads wl. Although this method is not the preferred method (Chen's method is preferred, on first page) it works, and is easy to perform quickly.
sudo lshw -C network
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:16 errors:0 dropped:0 overruns:0 frame:0
TX packets:16 errors:0 dropped:0 overruns:0 carrier:0
RX bytes:960 (960.0 B) TX bytes:960 (960.0 B)
lo no wireless extensions.
eth0 no wireless extensions.
wlan0 IEEE 802.11bg ESSIDff/any
Mode:Managed Access Point: Not-Associated Tx-Power=20 dBm
Retry long limit:7 RTS thrff Fragment thrff
root@ivan-lnv:/home/ivan# sudo lshw -C network
description: Network controller
product: BCM4312 802.11b/g
vendor: Broadcom Corporation
physical id: 0
bus info: pci@0000:04:00.0
width: 64 bits
capabilities: pm msi pciexpress bus_master cap_list
configuration: driver=b43-pci-bridge latency=0
resources: irq:18 memory:f4500000-f4503fff
description: Ethernet interface
product: NetLink BCM5906M Fast Ethernet PCI Express
vendor: Broadcom Corporation
physical id: 0
bus info: pci@0000:07:00.0
logical name: eth0
width: 64 bits
capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.102 duplex=half firmware=sb v3.04 latency=0 link=yes multicast=yes port=twisted pair
resources: irq:17 memory:f4600000-f460ffff
description: Wireless interface
physical id: 1
logical name: wlan0
capabilities: ethernet physical wireless
configuration: broadcast=yes multicast=yes wireless=IEEE 802.11bg
Do I need to use broadcom-wl-188.8.131.52.tar.bz2, broadcom-wl-184.108.40.206.tar.bz2, both or none (meaning a different one)? How do I do that?
Oh and BTW, I have no Eth0 after upgrading the system, not even booting up with the previous kernel, but I do have wirless and wired connection with XP.
I'm running Ubuntu Studio with Windows XP dual boot. Lenovo G550 with 4GB RAM. Model name is 2958J6Y.
Thank you so much for the help.
PS: I also posted it here because I didn't know which topic suits my situation best. I guess the other one, but anyways... Hope you can help me. =)
I'm past desperation now. I've tried to follow the first few and the last many tips of how to use this broadcom chipset. I just can't make it work on my Kubuntu Maverick AMD64 system.
I've removed, purged and rinstalled bcmwl-kernel-source, b43-fwcutter, and firmware-b43-lpphy-installer packages in many different orders and combinations. After blacklisting nothing and everything and all combinations of b43, wl and ssb and many reboots later I still can't use the wireless card on my notebook (HP pavillion dv2 - 14e4:4315 broadcom chipset).
The weirdest thing is that once I got it working on Kubuntu 9.10 (I remember to have only blacklisted the b43 module), it still worked on through all 10.04 upgrade and updates until 10.10. After upgrading from 10.04 to 10.10 wireless kept working. Then, after one 10.10 update I could not get the wireless interface to work anymore. Every time I power on my notebook the wireless led stays orange (it is supposed to be blue until you press the switch to kill wireless and turn it orange). I'm loosing what is left of my hair here...
In order to make sure it was not some leftover trash from earlier attempts or upgrades, I've even booted live images of: Kubuntu 10.10 AMD64 and regular 32-bit and Fedora 14 AMD64 and regular 32-bit. After trying to install and remove packages nothing worked: the same orange led.
Everyday I perform an "aptitude update && aptitude full-upgrade" eagerly hoping that some bug was fixed and I could use my notebook again on wireless.
Does anyone have a new idea (or an old one that I could try)?
Thanks in advance.