What do you all make of the below? It is a brand new Samsung SATA II drive.

Thanks.

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (11944) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 200) minutes.
Conveyance self-test routine
recommended polling time: ( 21) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 100 100 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0007 076 076 011 Pre-fail Always - 7970
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 65
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 253 253 051 Pre-fail Always - 0
8 Seek_Time_Performance 0x0025 100 100 015 Pre-fail Offline - 9886
9 Power_On_Hours 0x0032 099 099 000 Old_age Always - 3073
10 Spin_Retry_Count 0x0033 100 100 051 Pre-fail Always - 0
11 Calibration_Retry_Count 0x0012 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 65
13 Read_Soft_Error_Rate 0x000e 100 100 000 Old_age Always - 0
183 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 2
184 Unknown_Attribute 0x0033 100 100 000 Pre-fail Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 071 054 000 Old_age Always - 29 (Lifetime Min/Max 27/46)
194 Temperature_Celsius 0x0022 070 052 000 Old_age Always - 30 (Lifetime Min/Max 27/48)
195 Hardware_ECC_Recovered 0x001a 100 100 000 Old_age Always - 56050845
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 100 098 000 Old_age Always - 24
200 Multi_Zone_Error_Rate 0x000a 100 100 000 Old_age Always - 0
201 Soft_Read_Error_Rate 0x000a 100 100 000 Old_age Always - 0

SMART Error Log Version: 1
ATA Error Count: 11 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 11 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
00 d0 01 47 00 00 e0 1 sectors at LBA = 0x00000047 = 71

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 02 41 00 00 e0 00 00:17:02.340 READ DMA
c8 00 01 23 27 f4 e0 00 00:17:02.010 READ DMA
c8 00 01 e4 26 f4 e0 00 00:17:02.000 READ DMA
c8 00 01 00 00 00 e0 00 00:17:01.990 READ DMA
ec 00 00 00 00 00 a0 00 00:17:01.980 IDENTIFY DEVICE

Error 10 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 e4 e2 08 e0 Error: ICRC, ABRT at LBA = 0x0008e2e4 = 582372

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 01 e4 e2 08 e0 00 00:16:40.220 READ DMA
c8 00 01 e4 e2 08 e0 00 00:16:40.220 READ DMA
c8 00 01 2c d3 08 e0 00 00:16:40.220 READ DMA
c8 00 02 26 d3 08 e0 00 00:16:40.220 READ DMA
c8 00 01 5f 00 05 e0 00 00:16:40.220 READ DMA

Error 9 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 01 00 00 00 e0 00 00:15:57.450 READ DMA
ec 00 00 00 00 00 a0 00 00:15:57.440 IDENTIFY DEVICE
00 00 01 01 00 00 a0 00 00:15:57.290 NOP [Abort queued commands]
00 00 01 01 00 00 a0 ff 00:15:56.710 NOP [Abort queued commands]
00 00 01 01 00 00 a0 ff 00:15:53.730 NOP [Abort queued commands]

Error 8 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
00 d0 01 2c d3 08 e0 1 sectors at LBA = 0x0008d32c = 578348

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 02 26 d3 08 e0 00 00:14:26.340 READ DMA
c8 00 01 5f 00 05 e0 00 00:14:26.340 READ DMA
c8 00 01 5f 00 05 e0 00 00:14:26.340 READ DMA
c8 00 01 47 00 00 e0 00 00:14:26.340 READ DMA
c8 00 02 41 00 00 e0 00 00:14:26.330 READ DMA

Error 7 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 01 00 00 00 e0 00 00:06:12.620 READ DMA
ec 00 00 00 00 00 a0 00 00:06:12.610 IDENTIFY DEVICE
00 00 01 01 00 00 a0 00 00:06:12.460 NOP [Abort queued commands]
00 00 01 01 00 00 a0 ff 00:06:11.880 NOP [Abort queued commands]
00 00 01 01 00 00 a0 ff 00:06:08.880 NOP [Abort queued commands]

SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 3063 -
# 2 Extended offline Interrupted (host reset) 90% 3058 -

SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.