All seems okay, but cannot access internet >

**DancinHomer** · March 26th, 2009

Have been repairing Windows based PCs for 12years, but a Newb when it comes to Linux - still learning.

I've put Ubuntu on my laptop with no problems, but I've also just built a desktop system with Ubuntu on it but I can't access the internet.

All the desktop has on it, is the latest version of Ubuntu - nothing else has been added/configured from the defaults. I am connecting via an ethernet cable connected to a router (the same router my laptop is connecting fine to (wirelessly)).

From the network icon in the top right it says 'Wired network connection' when I hover the cursor over and when I access the Connection Information all the IP information is what I would expect to see.

But when I open Firefox and try to go to a website I get the 'Address not found' error.

The NIC is onboard on a Gigabyte GA-945GCM-S2L motherboard and is (I think) the Realtek 8169 NIC. I have tried downloading the Linux drivers from Realtek's website, but didn't seem to make a difference.

Any help would be much appreciated.

**khelben1979** · March 26th, 2009

What does ifconfig report?

Code:

sudo ifconfig

Also, what hardware you have over there might also make things easier to see how it looks like:

Code:

sudo dmesg

**DancinHomer** · March 27th, 2009

Here are results from the commands:

Code:

eth0      Link encap:Ethernet  HWaddr 00:1f:d0:18:73:01  
          UP BROADCAST RUNNING MULTICAST  MTU:64  Metric:1 
          RX packets:6 errors:0 dropped:2779020323 overruns:0 frame:0 
          TX packets:9 errors:0 dropped:0 overruns:0 carrier:0 
          collisions:0 txqueuelen:1000 
          RX bytes:1973 (1.9 KB)  TX bytes:1939 (1.9 KB) 
          Interrupt:221 Base address:0x4000 

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0 
          inet6 addr: ::1/128 Scope:Host 
          UP LOOPBACK RUNNING  MTU:16436  Metric:1 
          RX packets:240 errors:0 dropped:0 overruns:0 frame:0 
          TX packets:240 errors:0 dropped:0 overruns:0 carrier:0 
          collisions:0 txqueuelen:0 
          RX bytes:15040 (15.0 KB)  TX bytes:15040 (15.0 KB)

Code:

[    0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes) 
[    0.000000] TSC: PIT calibration confirmed by PMTIMER. 
[    0.000000] TSC: using PMTIMER calibration value 
[    0.000000] Detected 2199.992 MHz processor. 
[    0.004000] Console: colour VGA+ 80x25 
[    0.004000] console [tty0] enabled 
[    0.004000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) 
[    0.004000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) 
[    0.004000] Memory: 1016692k/1040320k available (2572k kernel code, 22944k reserved, 1160k data, 424k init, 122816k highmem) 
[    0.004000] virtual kernel memory layout: 
[    0.004000]     fixmap  : 0xffc77000 - 0xfffff000   (3616 kB) 
[    0.004000]     pkmap   : 0xff400000 - 0xff800000   (4096 kB) 
[    0.004000]     vmalloc : 0xf8800000 - 0xff3fe000   ( 107 MB) 
[    0.004000]     lowmem  : 0xc0000000 - 0xf8000000   ( 896 MB) 
[    0.004000]       .init : 0xc04ab000 - 0xc0515000   ( 424 kB) 
[    0.004000]       .data : 0xc038329a - 0xc04a5680   (1160 kB) 
[    0.004000]       .text : 0xc0100000 - 0xc038329a   (2572 kB) 
[    0.004000] Checking if this processor honours the WP bit even in supervisor mode...Ok. 
[    0.004000] CPA: page pool initialized 1 of 1 pages preallocated 
[    0.004000] SLUB: Genslabs=12, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 
[    0.004000] hpet clockevent registered 
[    0.004000] Calibrating delay loop (skipped), value calculated using timer frequency.. 4399.98 BogoMIPS (lpj=8799968) 
[    0.004000] Security Framework initialized 
[    0.004000] SELinux:  Disabled at boot. 
[    0.004000] AppArmor: AppArmor initialized 
[    0.004000] Mount-cache hash table entries: 512 
[    0.004000] Initializing cgroup subsys ns 
[    0.004000] Initializing cgroup subsys cpuacct 
[    0.004000] Initializing cgroup subsys memory 
[    0.004000] CPU: L1 I cache: 32K, L1 D cache: 32K 
[    0.004000] CPU: L2 cache: 1024K 
[    0.004000] CPU: Physical Processor ID: 0 
[    0.004000] CPU: Processor Core ID: 0 
[    0.004000] using mwait in idle threads. 
[    0.004000] Checking 'hlt' instruction... OK. 
[    0.017792] ACPI: Core revision 20080609 
[    0.019102] ACPI: Checking initramfs for custom DSDT 
[    0.320210] ENABLING IO-APIC IRQs 
[    0.320383] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 
[    0.360879] CPU0: Intel(R) Pentium(R) Dual  CPU  E2200  @ 2.20GHz stepping 0d 
[    0.364022] Booting processor 1/1 ip 6000 
[    0.004000] Initializing CPU#1 
[    0.004000] Calibrating delay using timer specific routine.. 4399.96 BogoMIPS (lpj=8799931) 
[    0.004000] CPU: L1 I cache: 32K, L1 D cache: 32K 
[    0.004000] CPU: L2 cache: 1024K 
[    0.004000] CPU: Physical Processor ID: 0 
[    0.004000] CPU: Processor Core ID: 1 
[    0.448396] CPU1: Intel(R) Pentium(R) Dual  CPU  E2200  @ 2.20GHz stepping 0d 
[    0.448411] checking TSC synchronization [CPU#0 -> CPU#1]: passed. 
[    0.452049] Brought up 2 CPUs 
[    0.452052] Total of 2 processors activated (8799.94 BogoMIPS). 
[    0.452074] CPU0 attaching sched-domain: 
[    0.452077]  domain 0: span 0-1 level MC 
[    0.452079]   groups: 0 1 
[    0.452085] CPU1 attaching sched-domain: 
[    0.452087]  domain 0: span 0-1 level MC 
[    0.452089]   groups: 1 0 
[    0.452161] net_namespace: 840 bytes 
[    0.452161] Booting paravirtualized kernel on bare hardware 
[    0.452272] Time: 10:12:30  Date: 03/27/09 
[    0.452298] NET: Registered protocol family 16 
[    0.452316] EISA bus registered 
[    0.452316] ACPI: bus type pci registered 
[    0.452316] PCI: Found Intel Corporation 945G/GZ/P/PL Express Memory Controller Hub without MMCONFIG support. 
[    0.459535] PCI: PCI BIOS revision 3.00 entry at 0xfac30, last bus=3 
[    0.459537] PCI: Using configuration type 1 for base access 
[    0.460555] ACPI: EC: Look up EC in DSDT 
[    0.465924] ACPI: Interpreter enabled 
[    0.465928] ACPI: (supports S0 S1 S4 S5) 
[    0.465942] ACPI: Using IOAPIC for interrupt routing 
[    0.468708] ACPI: PCI Root Bridge [PCI0] (0000:00) 
[    0.468708] PCI: 0000:00:02.0 reg 10 32bit mmio: [d1100000, d117ffff] 
[    0.468708] PCI: 0000:00:02.0 reg 14 io port: [b000, b007] 
[    0.468708] PCI: 0000:00:02.0 reg 18 32bit mmio: [c0000000, cfffffff] 
[    0.468708] PCI: 0000:00:02.0 reg 1c 32bit mmio: [d1180000, d11bffff] 
[    0.468708] PCI: 0000:00:1b.0 reg 10 64bit mmio: [d11c0000, d11c3fff] 
[    0.468708] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold 
[    0.468708] pci 0000:00:1b.0: PME# disabled 
[    0.468708] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold 
[    0.468708] pci 0000:00:1c.0: PME# disabled 
[    0.468708] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold 
[    0.468708] pci 0000:00:1c.1: PME# disabled 
[    0.468708] PCI: 0000:00:1d.0 reg 20 io port: [b400, b41f] 
[    0.468708] PCI: 0000:00:1d.1 reg 20 io port: [b800, b81f] 
[    0.468708] PCI: 0000:00:1d.2 reg 20 io port: [bc00, bc1f] 
[    0.468708] PCI: 0000:00:1d.3 reg 20 io port: [c000, c01f] 
[    0.468708] PCI: 0000:00:1d.7 reg 10 32bit mmio: [d11c4000, d11c43ff] 
[    0.468708] pci 0000:00:1f.0: quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO 
[    0.468708] pci 0000:00:1f.0: quirk: region 0480-04bf claimed by ICH6 GPIO 
[    0.468723] PCI: 0000:00:1f.2 reg 10 io port: [0, 7] 
[    0.468729] PCI: 0000:00:1f.2 reg 14 io port: [0, 3] 
[    0.468734] PCI: 0000:00:1f.2 reg 18 io port: [0, 7] 
[    0.468740] PCI: 0000:00:1f.2 reg 1c io port: [0, 3] 
[    0.468746] PCI: 0000:00:1f.2 reg 20 io port: [f000, f00f] 
[    0.468766] pci 0000:00:1f.2: PME# supported from D3hot 
[    0.468770] pci 0000:00:1f.2: PME# disabled 
[    0.468811] PCI: 0000:00:1f.3 reg 20 io port: [500, 51f] 
[    0.468871] PCI: bridge 0000:00:1c.0 io port: [9000, 9fff] 
[    0.468921] PCI: 0000:02:00.0 reg 10 io port: [a000, a0ff] 
[    0.468936] PCI: 0000:02:00.0 reg 18 32bit mmio: [d1010000, d1010fff] 
[    0.468950] PCI: 0000:02:00.0 reg 20 32bit mmio: [d1000000, d100ffff] 
[    0.468964] PCI: 0000:02:00.0 reg 30 32bit mmio: [0, ffff] 
[    0.468993] pci 0000:02:00.0: supports D1 
[    0.468994] pci 0000:02:00.0: supports D2 
[    0.468996] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold 
[    0.469001] pci 0000:02:00.0: PME# disabled 
[    0.469035] PCI: bridge 0000:00:1c.1 io port: [a000, afff] 
[    0.469039] PCI: bridge 0000:00:1c.1 32bit mmio: [d0000000, d0ffffff] 
[    0.469045] PCI: bridge 0000:00:1c.1 64bit mmio pref: [d1000000, d10fffff] 
[    0.469095] pci 0000:00:1e.0: transparent bridge 
[    0.469098] PCI: bridge 0000:00:1e.0 io port: [8000, 8fff] 
[    0.469119] bus 00 -> node 0 
[    0.469125] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] 
[    0.469379] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT] 
[    0.469475] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX1._PRT] 
[    0.472128] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT] 
[    0.480196] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 11 *12 14 15) 
[    0.480230] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 14 15) 
[    0.480332] ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 9 10 11 12 14 15) 
[    0.480434] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) 
[    0.480538] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled. 
[    0.480645] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled. 
[    0.480748] ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled. 
[    0.480851] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 *5 6 7 9 10 11 12 14 15) 
[    0.480904] Linux Plug and Play Support v0.97 (c) Adam Belay 
[    0.480904] pnp: PnP ACPI init 
[    0.480904] ACPI: bus type pnp registered 
[    0.484248] pnp: PnP ACPI: found 14 devices 
[    0.484248] ACPI: ACPI bus type pnp unregistered 
[    0.484248] PnPBIOS: Disabled by ACPI PNP 
[    0.484248] PCI: Using ACPI for IRQ routing 
[    0.492044] NET: Registered protocol family 8 
[    0.492049] NET: Registered protocol family 20 
[    0.492074] NetLabel: Initializing 
[    0.492074] NetLabel:  domain hash size = 128 
[    0.492074] NetLabel:  protocols = UNLABELED CIPSOv4 
[    0.492084] NetLabel:  unlabeled traffic allowed by default 
[    0.492092] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 
[    0.492101] hpet0: 3 64-bit timers, 14318180 Hz 
[    0.493539] tracer: 772 pages allocated for 65536 entries of 48 bytes 
[    0.493542]    actual entries 65620 
[    0.493632] AppArmor: AppArmor Filesystem Enabled 
[    0.493653] ACPI: RTC can wake from S4 
[    0.500087] system 00:01: ioport range 0x4d0-0x4d1 has been reserved 
[    0.500093] system 00:01: ioport range 0x290-0x29f has been reserved 
[    0.500097] system 00:01: ioport range 0x800-0x87f has been reserved 
[    0.500102] system 00:01: ioport range 0x290-0x294 has been reserved 
[    0.500107] system 00:01: ioport range 0x880-0x88f has been reserved 
[    0.500127] system 00:0a: ioport range 0x400-0x4bf could not be reserved 
[    0.500138] system 00:0b: iomem range 0xf0000000-0xf3ffffff could not be reserved 
[    0.500149] system 00:0c: iomem range 0xca800-0xcbfff has been reserved 
[    0.500154] system 00:0c: iomem range 0xf0000-0xf7fff could not be reserved 
[    0.500159] system 00:0c: iomem range 0xf8000-0xfbfff could not be reserved 
[    0.500164] system 00:0c: iomem range 0xfc000-0xfffff could not be reserved 
[    0.500169] system 00:0c: iomem range 0x3f7f0000-0x3f7fffff could not be reserved 
[    0.500174] system 00:0c: iomem range 0x0-0x9ffff could not be reserved 
[    0.500179] system 00:0c: iomem range 0x100000-0x3f7effff could not be reserved 
[    0.500184] system 00:0c: iomem range 0xfec00000-0xfec00fff could not be reserved 
[    0.500190] system 00:0c: iomem range 0xfed13000-0xfed1dfff could not be reserved 
[    0.500195] system 00:0c: iomem range 0xfed20000-0xfed8ffff could not be reserved 
[    0.500200] system 00:0c: iomem range 0xfee00000-0xfee00fff could not be reserved 
[    0.500205] system 00:0c: iomem range 0xffb00000-0xffb7ffff could not be reserved 
[    0.500210] system 00:0c: iomem range 0xfff00000-0xffffffff could not be reserved 
[    0.500215] system 00:0c: iomem range 0xe0000-0xeffff has been reserved 
[    0.500459] Switched to high resolution mode on CPU 1 
[    0.504058] Switched to high resolution mode on CPU 0 
[    0.535235] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:01 
[    0.535238] pci 0000:00:1c.0:   IO window: 0x9000-0x9fff 
[    0.535243] pci 0000:00:1c.0:   MEM window: disabled 
[    0.535247] pci 0000:00:1c.0:   PREFETCH window: disabled 
[    0.535254] pci 0000:00:1c.1: PCI bridge, secondary bus 0000:02 
[    0.535257] pci 0000:00:1c.1:   IO window: 0xa000-0xafff 
[    0.535262] pci 0000:00:1c.1:   MEM window: 0xd0000000-0xd0ffffff 
[    0.535266] pci 0000:00:1c.1:   PREFETCH window: 0x000000d1000000-0x000000d10fffff 
[    0.535272] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:03 
[    0.535275] pci 0000:00:1e.0:   IO window: 0x8000-0x8fff 
[    0.535280] pci 0000:00:1e.0:   MEM window: disabled 
[    0.535283] pci 0000:00:1e.0:   PREFETCH window: disabled 
[    0.535300] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 
[    0.535305] pci 0000:00:1c.0: setting latency timer to 64 
[    0.535313] pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 
[    0.535317] pci 0000:00:1c.1: setting latency timer to 64 
[    0.535323] pci 0000:00:1e.0: setting latency timer to 64 
[    0.535326] bus: 00 index 0 io port: [0, ffff] 
[    0.535328] bus: 00 index 1 mmio: [0, ffffffff] 
[    0.535330] bus: 01 index 0 io port: [9000, 9fff] 
[    0.535332] bus: 01 index 1 mmio: [0, 0] 
[    0.535334] bus: 01 index 2 mmio: [0, 0] 
[    0.535335] bus: 01 index 3 mmio: [0, 0] 
[    0.535337] bus: 02 index 0 io port: [a000, afff] 
[    0.535339] bus: 02 index 1 mmio: [d0000000, d0ffffff] 
[    0.535341] bus: 02 index 2 mmio: [d1000000, d10fffff] 
[    0.535343] bus: 02 index 3 mmio: [0, 0] 
[    0.535345] bus: 03 index 0 io port: [8000, 8fff] 
[    0.535346] bus: 03 index 1 mmio: [0, 0] 
[    0.535348] bus: 03 index 2 mmio: [0, 0] 
[    0.535350] bus: 03 index 3 io port: [0, ffff] 
[    0.535352] bus: 03 index 4 mmio: [0, ffffffff] 
[    0.535360] NET: Registered protocol family 2 
[    0.548110] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) 
[    0.548363] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) 
[    0.548862] TCP bind hash table entries: 65536 (order: 7, 524288 bytes) 
[    0.549203] TCP: Hash tables configured (established 131072 bind 65536) 
[    0.549207] TCP reno registered 
[    0.556165] NET: Registered protocol family 1 
[    0.556305] checking if image is initramfs... it is 
[    1.176768] Freeing initrd memory: 7994k freed 
[    1.177877] audit: initializing netlink socket (disabled) 
[    1.177901] type=2000 audit(1238148750.177:1): initialized 
[    1.183220] highmem bounce pool size: 64 pages 
[    1.183226] HugeTLB registered 4 MB page size, pre-allocated 0 pages 
[    1.185364] VFS: Disk quotas dquot_6.5.1 
[    1.185452] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) 
[    1.185554] msgmni has been set to 1762 
[    1.185674] io scheduler noop registered 
[    1.185677] io scheduler anticipatory registered 
[    1.185679] io scheduler deadline registered 
[    1.185690] io scheduler cfq registered (default) 
[    1.185705] pci 0000:00:02.0: Boot video device 
[    1.185878] pcieport-driver 0000:00:1c.0: setting latency timer to 64 
[    1.185909] pcieport-driver 0000:00:1c.0: found MSI capability 
[    1.185944] pci_express 0000:00:1c.0:pcie00: allocate port service 
[    1.185987] pci_express 0000:00:1c.0:pcie02: allocate port service 
[    1.186075] pcieport-driver 0000:00:1c.1: setting latency timer to 64 
[    1.186106] pcieport-driver 0000:00:1c.1: found MSI capability 
[    1.186138] pci_express 0000:00:1c.1:pcie00: allocate port service 
[    1.186182] pci_express 0000:00:1c.1:pcie02: allocate port service 
[    1.186483] isapnp: Scanning for PnP cards... 
[    1.539417] isapnp: No Plug & Play device found 
[    1.570137] Serial: 8250/16550 driver4 ports, IRQ sharing enabled 
[    1.570262] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 
[    1.570958] 00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 
[    1.572591] brd: module loaded 
[    1.572654] input: Macintosh mouse button emulation as /devices/virtual/input/input0 
[    1.572771] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1 
[    1.572774] PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp 
[    1.572913] serio: i8042 KBD port at 0x60,0x64 irq 1 
[    1.573157] mice: PS/2 mouse device common for all mice 
[    1.573281] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0 
[    1.573303] rtc0: alarms up to one month, hpet irqs 
[    1.573420] EISA: Probing bus 0 at eisa.0 
[    1.573445] Cannot allocate resource for EISA slot 8 
[    1.573447] EISA: Detected 0 cards. 
[    1.573451] cpuidle: using governor ladder 
[    1.573453] cpuidle: using governor menu 
[    1.573930] TCP cubic registered 
[    1.573957] Using IPI No-Shortcut mode 
[    1.574131] registered taskstats version 1 
[    1.574221]   Magic number: 1:238:225 
[    1.574250] tty ttyu9: hash matches 
[    1.574257] tty ttyrc: hash matches 
[    1.574342] rtc_cmos 00:03: setting system clock to 2009-03-27 10:12:31 UTC (1238148751) 
[    1.574345] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found 
[    1.574347] EDD information not available. 
[    1.574538] Freeing unused kernel memory: 424k freed 
[    1.574572] Write protecting the kernel text: 2576k 
[    1.574595] Write protecting the kernel read-only data: 936k 
[    1.591757] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1 
[    1.689996] fuse init (API version 7.9) 
[    1.720182] processor ACPI0007:00: registered as cooling_device0 
[    1.720187] ACPI: Processor [CPU0] (supports 8 throttling states) 
[    1.720366] ACPI: SSDT 3F7F7040, 0087 (r1  PmRef  Cpu1Ist     3000 INTL 20040311) 
[    1.762138] processor ACPI0007:01: registered as cooling_device1 
[    1.762143] ACPI: Processor [CPU1] (supports 8 throttling states) 
[    2.030016] usbcore: registered new interface driver usbfs 
[    2.030043] usbcore: registered new interface driver hub 
[    2.030255] usbcore: registered new device driver usb 
[    2.049044] USB Universal Host Controller Interface driver v3.0 
[    2.049118] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 
[    2.049130] uhci_hcd 0000:00:1d.0: setting latency timer to 64 
[    2.049133] uhci_hcd 0000:00:1d.0: UHCI Host Controller 
[    2.049184] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1 
[    2.049219] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000b400 
[    2.049393] usb usb1: configuration #1 chosen from 1 choice 
[    2.049421] hub 1-0:1.0: USB hub found 
[    2.049429] hub 1-0:1.0: 2 ports detected 
[    2.085192] No dock devices found. 
[    2.098314] SCSI subsystem initialized 
[    2.113768] libata version 3.00 loaded. 
[    2.152294] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 
[    2.152308] uhci_hcd 0000:00:1d.1: setting latency timer to 64 
[    2.152313] uhci_hcd 0000:00:1d.1: UHCI Host Controller 
[    2.152338] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2 
[    2.152380] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000b800 
[    2.152468] usb usb2: configuration #1 chosen from 1 choice 
[    2.152495] hub 2-0:1.0: USB hub found 
[    2.152501] hub 2-0:1.0: 2 ports detected 
[    2.256324] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 
[    2.256335] uhci_hcd 0000:00:1d.2: setting latency timer to 64 
[    2.256338] uhci_hcd 0000:00:1d.2: UHCI Host Controller 
[    2.256363] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3 
[    2.256394] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000bc00 
[    2.256483] usb usb3: configuration #1 chosen from 1 choice 
[    2.256508] hub 3-0:1.0: USB hub found 
[    2.256514] hub 3-0:1.0: 2 ports detected 
[    2.360264] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16 
[    2.360274] uhci_hcd 0000:00:1d.3: setting latency timer to 64 
[    2.360278] uhci_hcd 0000:00:1d.3: UHCI Host Controller 
[    2.360302] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4 
[    2.360334] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000c000 
[    2.360423] usb usb4: configuration #1 chosen from 1 choice 
[    2.360448] hub 4-0:1.0: USB hub found 
[    2.360459] hub 4-0:1.0: 2 ports detected 
[    2.568375] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23 
[    2.568393] ehci_hcd 0000:00:1d.7: setting latency timer to 64 
[    2.568397] ehci_hcd 0000:00:1d.7: EHCI Host Controller 
[    2.568429] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5 
[    2.572341] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported 
[    2.572352] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xd11c4000 
[    2.680048] usb 4-1: new low speed USB device using uhci_hcd and address 2 
[    2.692101] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 
[    2.692283] usb usb5: configuration #1 chosen from 1 choice 
[    2.692310] hub 5-0:1.0: USB hub found 
[    2.692319] hub 5-0:1.0: 8 ports detected 
[    2.748066] hub 4-0:1.0: unable to enumerate USB device on port 1 
[    2.901268] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded 
[    2.901283] r8169 0000:02:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 
[    2.901299] r8169 0000:02:00.0: setting latency timer to 64 
[    2.901608] eth0: RTL8168c/8111c at 0xf8834000, 00:1f:d0:18:73:01, XID 3c4000c0 IRQ 221 
[    2.907782] pata_acpi 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19 
[    2.907814] pata_acpi 0000:00:1f.2: setting latency timer to 64 
[    2.907827] pata_acpi 0000:00:1f.2: PCI INT B disabled 
[    2.915808] ata_piix 0000:00:1f.2: version 2.12 
[    2.915827] ata_piix 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19 
[    2.915831] ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ] 
[    2.915876] ata_piix 0000:00:1f.2: setting latency timer to 64 
[    2.917271] scsi0 : ata_piix 
[    2.917375] scsi1 : ata_piix 
[    2.918074] ata1: SATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14 
[    2.918078] ata2: SATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15 
[    3.088205] ata1.00: HPA unlocked: 156299375 -> 156301488, native 156301488 
[    3.088211] ata1.00: ATA-7: Hitachi HDS721680PLA380, P21OABEA, max UDMA/133 
[    3.088213] ata1.00: 156301488 sectors, multi 16: LBA48 NCQ (depth 0/32) 
[    3.104425] ata1.00: configured for UDMA/133 
[    3.260186] ata2.01: NODEV after polling detection 
[    3.268222] ata2.00: ATAPI: TSSTcorp CDDVDW SH-S223F, SB00, max UDMA/100 
[    3.284224] ata2.00: configured for UDMA/100 
[    3.284334] scsi 0:0:0:0: Direct-Access     ATA      Hitachi HDS72168 P21O PQ: 0 ANSI: 5 
[    3.285057] scsi 1:0:0:0: CD-ROM            TSSTcorp CDDVDW SH-S223F  SB00 PQ: 0 ANSI: 5 
[    3.291190] scsi 0:0:0:0: Attached scsi generic sg0 type 0 
[    3.291223] scsi 1:0:0:0: Attached scsi generic sg1 type 5 
[    3.304466] Driver 'sd' needs updating - please use bus_type methods 
[    3.304589] sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB) 
[    3.304609] sd 0:0:0:0: [sda] Write Protect is off 
[    3.304612] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 
[    3.304641] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA 
[    3.304736] sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB) 
[    3.304753] sd 0:0:0:0: [sda] Write Protect is off 
[    3.304755] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 
[    3.304785] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA 
[    3.304789]  sda:<4>Driver 'sr' needs updating - please use bus_type methods 
[    3.320413]  sda1 sda2 < sda5 sda6 > 
[    3.352919] sd 0:0:0:0: [sda] Attached SCSI disk 
[    3.357707] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray 
[    3.357712] Uniform CD-ROM driver Revision: 3.20 
[    3.357816] sr 1:0:0:0: Attached scsi CD-ROM sr0 
[    3.368049] usb 4-1: new low speed USB device using uhci_hcd and address 3 
[    3.568370] usb 4-1: configuration #1 chosen from 1 choice 
[    3.593226] usbcore: registered new interface driver hiddev 
[    3.593735] PM: Starting manual resume from disk 
[    3.593738] PM: Resume from partition 8:6 
[    3.593740] PM: Checking hibernation image. 
[    3.593880] PM: Resume from disk failed. 
[    3.631664] input: HID 1241:1111 as /devices/pci0000:00/0000:00:1d.3/usb4/4-1/4-1:1.0/input/input2 
[    3.631952] input,hidraw0: USB HID v1.10 Mouse [HID 1241:1111] on usb-0000:00:1d.3-1 
[    3.631975] usbcore: registered new interface driver usbhid 
[    3.631979] usbhid: v2.6:USB HID core driver 
[    3.640875] kjournald starting.  Commit interval 5 seconds 
[    3.640891] EXT3-fs: mounted filesystem with ordered data mode. 
[    9.140968] udevd version 124 started 
[    9.532575] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 
[    9.562105] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 
[    9.588528] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3 
[    9.602155] ACPI: Power Button (FF) [PWRF] 
[    9.602237] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input4 
[    9.621037] ACPI: Power Button (CM) [PWRB] 
[    9.694889] Linux agpgart interface v0.103 
[    9.775667] agpgart-intel 0000:00:00.0: Intel 945G Chipset 
[    9.775915] agpgart-intel 0000:00:00.0: detected 7932K stolen memory 
[    9.807299] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xc0000000 
[    9.876700] iTCO_vendor_support: vendor-support=0 
[    9.894202] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008) 
[    9.897106] iTCO_wdt: Found a ICH7 or ICH7R TCO device (Version=2, TCOBASE=0x0460) 
[    9.897199] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0) 
[    9.950882] parport_pc 00:08: reported by Plug and Play ACPI 
[    9.950929] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE] 
[   10.047769] intel_rng: FWH not detected 
[   10.213714] input: PC Speaker as /devices/platform/pcspkr/input/input5 
[   10.423025] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 
[   10.423052] HDA Intel 0000:00:1b.0: setting latency timer to 64 
[   10.455337] hda_codec: Unknown model for ALC662, trying auto-probe from BIOS... 
[   12.106220] lp0: using parport0 (interrupt-driven). 
[   12.225106] Adding 1662688k swap on /dev/sda6.  Priority:-1 extents:1 across:1662688k 
[   12.784988] EXT3 FS on sda5, internal journal 
[   13.698471] type=1505 audit(1238148763.689:2): operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" name2="default" pid=3967 
[   13.849327] type=1505 audit(1238148763.842:3): operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" name2="default" pid=3972 
[   13.849528] type=1505 audit(1238148763.842:4): operation="profile_load" name="/usr/sbin/cupsd" name2="default" pid=3972 
[   13.966312] ip_tables: (C) 2000-2006 Netfilter Core Team 
[   14.467381] ACPI: WMI: Mapper loaded 
[   15.250552] warning: `avahi-daemon' uses 32-bit capabilities (legacy support in use) 
[   15.293329] apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac) 
[   15.293336] apm: disabled - APM is not SMP safe. 
[   15.467452] ppdev: user-space parallel port driver 
[   16.543560] Bluetooth: Core ver 2.13 
[   16.544377] NET: Registered protocol family 31 
[   16.544386] Bluetooth: HCI device and connection manager initialized 
[   16.544392] Bluetooth: HCI socket layer initialized 
[   16.561835] Bluetooth: L2CAP ver 2.11 
[   16.561844] Bluetooth: L2CAP socket layer initialized 
[   16.576087] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 
[   16.576098] Bluetooth: BNEP filters: protocol multicast 
[   16.603094] Bridge firewalling registered 
[   16.603312] pan0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature. 
[   16.617735] Bluetooth: SCO (Voice Link) ver 0.6 
[   16.617744] Bluetooth: SCO socket layer initialized 
[   16.693994] Bluetooth: RFCOMM socket layer initialized 
[   16.694015] Bluetooth: RFCOMM TTY layer initialized 
[   16.694019] Bluetooth: RFCOMM ver 1.10 
[   19.394181] [drm] Initialized drm 1.1.0 20060810 
[   19.401569] pci 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 
[   19.401583] pci 0000:00:02.0: setting latency timer to 64 
[   19.401771] [drm] Initialized i915 1.6.0 20060119 on minor 0 
[   20.808707] r8169: eth0: link up 
[   20.808722] r8169: eth0: link up 
[   21.109084] NET: Registered protocol family 17 
[  112.026551] type=1503 audit(1238148862.017:5): operation="inode_permission" requested_mask="r::" denied_mask="r::" fsuid=7 name="/proc/5476/net/" pid=5476 profile="/usr/sbin/cupsd" 
[  112.100103] NET: Registered protocol family 10 
[  112.101018] lo: Disabled Privacy Extensions 
[  112.103284] type=1503 audit(1238148862.093:6): operation="socket_create" family="ax25" sock_type="dgram" protocol=0 pid=5476 profile="/usr/sbin/cupsd" 
[  112.103784] type=1503 audit(1238148862.093:7): operation="socket_create" family="netrom" sock_type="seqpacket" protocol=0 pid=5476 profile="/usr/sbin/cupsd" 
[  112.104285] type=1503 audit(1238148862.097:8): operation="socket_create" family="rose" sock_type="dgram" protocol=0 pid=5476 profile="/usr/sbin/cupsd" 
[  112.104745] type=1503 audit(1238148862.097:9): operation="socket_create" family="ipx" sock_type="dgram" protocol=0 pid=5476 profile="/usr/sbin/cupsd" 
[  112.105200] type=1503 audit(1238148862.097:10): operation="socket_create" family="appletalk" sock_type="dgram" protocol=0 pid=5476 profile="/usr/sbin/cupsd" 
[  112.105672] type=1503 audit(1238148862.097:11): operation="socket_create" family="econet" sock_type="dgram" protocol=0 pid=5476 profile="/usr/sbin/cupsd" 
[  112.106134] type=1503 audit(1238148862.097:12): operation="socket_create" family="ash" sock_type="dgram" protocol=0 pid=5476 profile="/usr/sbin/cupsd" 
[  112.106148] type=1503 audit(1238148862.097:13): operation="socket_create" family="x25" sock_type="seqpacket" protocol=0 pid=5476 profile="/usr/sbin/cupsd" 
[  112.106236] type=1503 audit(1238148862.097:14): operation="inode_permission" requested_mask="::r" denied_mask="::r" fsuid=7 name="/proc/5476/net/dev" pid=5476 profile="/usr/sbin/cupsd" 
[  112.940280] ppdev0: registered pardevice 
[  112.988178] ppdev0: unregistered pardevice 
[  114.059865] ppdev0: registered pardevice 
[  114.108272] ppdev0: unregistered pardevice 
[  114.120436] ppdev0: registered pardevice 
[  114.168021] ppdev0: unregistered pardevice

Thanks

**coutts99** · March 27th, 2009

Originally Posted by DancinHomer

Here are results from the commands:

Code:

eth0      Link encap:Ethernet  HWaddr 00:1f:d0:18:73:01  
          UP BROADCAST RUNNING MULTICAST  MTU:64  Metric:1 
          RX packets:6 errors:0 dropped:2779020323 overruns:0 frame:0 
          TX packets:9 errors:0 dropped:0 overruns:0 carrier:0 
          collisions:0 txqueuelen:1000 
          RX bytes:1973 (1.9 KB)  TX bytes:1939 (1.9 KB) 
          Interrupt:221 Base address:0x4000

eth0 has not got an IP address. Is there a DHCP client running? ps ax| grep dhcp

Hmm, dropped:2779020323 is a bit worrying too!

**coutts99** · March 27th, 2009

Can you try -:

1) unload driver - rmmod r8169
2) load the driver again - modprobe r8169

And send the output of dmesg again?

**DancinHomer** · March 27th, 2009

eth0 has not got an IP address

When I right-click network icon and select 'Connection Information' it says IP address is 10.0.0.4 (what I would expect)

Also, when I type 'rmmod r8169' I get message 'ERROR: Removing 'R8169': Operation not permitted'

Thanks for all your help so far..

**coutts99** · March 27th, 2009

sorry put sudo infront of those commands

**DancinHomer** · March 27th, 2009

No Probs - Looks like it might be cutting off the top part of the report?

Unloaded and reloaded 'R8169':

Code:

[    0.004000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) 
[    0.004000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) 
[    0.004000] Memory: 1016692k/1040320k available (2572k kernel code, 22944k reserved, 1160k data, 424k init, 122816k highmem) 
[    0.004000] virtual kernel memory layout: 
[    0.004000]     fixmap  : 0xffc77000 - 0xfffff000   (3616 kB) 
[    0.004000]     pkmap   : 0xff400000 - 0xff800000   (4096 kB) 
[    0.004000]     vmalloc : 0xf8800000 - 0xff3fe000   ( 107 MB) 
[    0.004000]     lowmem  : 0xc0000000 - 0xf8000000   ( 896 MB) 
[    0.004000]       .init : 0xc04ab000 - 0xc0515000   ( 424 kB) 
[    0.004000]       .data : 0xc038329a - 0xc04a5680   (1160 kB) 
[    0.004000]       .text : 0xc0100000 - 0xc038329a   (2572 kB) 
[    0.004000] Checking if this processor honours the WP bit even in supervisor mode...Ok. 
[    0.004000] CPA: page pool initialized 1 of 1 pages preallocated 
[    0.004000] SLUB: Genslabs=12, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 
[    0.004000] hpet clockevent registered 
[    0.004000] Calibrating delay loop (skipped), value calculated using timer frequency.. 4399.98 BogoMIPS (lpj=8799968) 
[    0.004000] Security Framework initialized 
[    0.004000] SELinux:  Disabled at boot. 
[    0.004000] AppArmor: AppArmor initialized 
[    0.004000] Mount-cache hash table entries: 512 
[    0.004000] Initializing cgroup subsys ns 
[    0.004000] Initializing cgroup subsys cpuacct 
[    0.004000] Initializing cgroup subsys memory 
[    0.004000] CPU: L1 I cache: 32K, L1 D cache: 32K 
[    0.004000] CPU: L2 cache: 1024K 
[    0.004000] CPU: Physical Processor ID: 0 
[    0.004000] CPU: Processor Core ID: 0 
[    0.004000] using mwait in idle threads. 
[    0.004000] Checking 'hlt' instruction... OK. 
[    0.017779] ACPI: Core revision 20080609 
[    0.019104] ACPI: Checking initramfs for custom DSDT 
[    0.320211] ENABLING IO-APIC IRQs 
[    0.320386] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 
[    0.360819] CPU0: Intel(R) Pentium(R) Dual  CPU  E2200  @ 2.20GHz stepping 0d 
[    0.364022] Booting processor 1/1 ip 6000 
[    0.004000] Initializing CPU#1 
[    0.004000] Calibrating delay using timer specific routine.. 4399.96 BogoMIPS (lpj=8799931) 
[    0.004000] CPU: L1 I cache: 32K, L1 D cache: 32K 
[    0.004000] CPU: L2 cache: 1024K 
[    0.004000] CPU: Physical Processor ID: 0 
[    0.004000] CPU: Processor Core ID: 1 
[    0.448397] CPU1: Intel(R) Pentium(R) Dual  CPU  E2200  @ 2.20GHz stepping 0d 
[    0.448412] checking TSC synchronization [CPU#0 -> CPU#1]: passed. 
[    0.452050] Brought up 2 CPUs 
[    0.452053] Total of 2 processors activated (8799.94 BogoMIPS). 
[    0.452075] CPU0 attaching sched-domain: 
[    0.452078]  domain 0: span 0-1 level MC 
[    0.452081]   groups: 0 1 
[    0.452086] CPU1 attaching sched-domain: 
[    0.452088]  domain 0: span 0-1 level MC 
[    0.452090]   groups: 1 0 
[    0.452162] net_namespace: 840 bytes 
[    0.452162] Booting paravirtualized kernel on bare hardware 
[    0.452270] Time: 12:22:52  Date: 03/27/09 
[    0.452296] NET: Registered protocol family 16 
[    0.452316] EISA bus registered 
[    0.452316] ACPI: bus type pci registered 
[    0.452316] PCI: Found Intel Corporation 945G/GZ/P/PL Express Memory Controller Hub without MMCONFIG support. 
[    0.459537] PCI: PCI BIOS revision 3.00 entry at 0xfac30, last bus=3 
[    0.459539] PCI: Using configuration type 1 for base access 
[    0.460576] ACPI: EC: Look up EC in DSDT 
[    0.465929] ACPI: Interpreter enabled 
[    0.465933] ACPI: (supports S0 S1 S4 S5) 
[    0.465947] ACPI: Using IOAPIC for interrupt routing 
[    0.468711] ACPI: PCI Root Bridge [PCI0] (0000:00) 
[    0.468711] PCI: 0000:00:02.0 reg 10 32bit mmio: [d1100000, d117ffff] 
[    0.468711] PCI: 0000:00:02.0 reg 14 io port: [b000, b007] 
[    0.468711] PCI: 0000:00:02.0 reg 18 32bit mmio: [c0000000, cfffffff] 
[    0.468711] PCI: 0000:00:02.0 reg 1c 32bit mmio: [d1180000, d11bffff] 
[    0.468711] PCI: 0000:00:1b.0 reg 10 64bit mmio: [d11c0000, d11c3fff] 
[    0.468711] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold 
[    0.468711] pci 0000:00:1b.0: PME# disabled 
[    0.468711] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold 
[    0.468711] pci 0000:00:1c.0: PME# disabled 
[    0.468711] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold 
[    0.468711] pci 0000:00:1c.1: PME# disabled 
[    0.468711] PCI: 0000:00:1d.0 reg 20 io port: [b400, b41f] 
[    0.468711] PCI: 0000:00:1d.1 reg 20 io port: [b800, b81f] 
[    0.468711] PCI: 0000:00:1d.2 reg 20 io port: [bc00, bc1f] 
[    0.468711] PCI: 0000:00:1d.3 reg 20 io port: [c000, c01f] 
[    0.468711] PCI: 0000:00:1d.7 reg 10 32bit mmio: [d11c4000, d11c43ff] 
[    0.468711] pci 0000:00:1f.0: quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO 
[    0.468711] pci 0000:00:1f.0: quirk: region 0480-04bf claimed by ICH6 GPIO 
[    0.468723] PCI: 0000:00:1f.2 reg 10 io port: [0, 7] 
[    0.468728] PCI: 0000:00:1f.2 reg 14 io port: [0, 3] 
[    0.468734] PCI: 0000:00:1f.2 reg 18 io port: [0, 7] 
[    0.468740] PCI: 0000:00:1f.2 reg 1c io port: [0, 3] 
[    0.468745] PCI: 0000:00:1f.2 reg 20 io port: [f000, f00f] 
[    0.468766] pci 0000:00:1f.2: PME# supported from D3hot 
[    0.468770] pci 0000:00:1f.2: PME# disabled 
[    0.468810] PCI: 0000:00:1f.3 reg 20 io port: [500, 51f] 
[    0.468870] PCI: bridge 0000:00:1c.0 io port: [9000, 9fff] 
[    0.468924] PCI: 0000:02:00.0 reg 10 io port: [a000, a0ff] 
[    0.468938] PCI: 0000:02:00.0 reg 18 32bit mmio: [d1010000, d1010fff] 
[    0.468953] PCI: 0000:02:00.0 reg 20 32bit mmio: [d1000000, d100ffff] 
[    0.468967] PCI: 0000:02:00.0 reg 30 32bit mmio: [0, ffff] 
[    0.468995] pci 0000:02:00.0: supports D1 
[    0.468997] pci 0000:02:00.0: supports D2 
[    0.468999] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold 
[    0.469004] pci 0000:02:00.0: PME# disabled 
[    0.469037] PCI: bridge 0000:00:1c.1 io port: [a000, afff] 
[    0.469041] PCI: bridge 0000:00:1c.1 32bit mmio: [d0000000, d0ffffff] 
[    0.469048] PCI: bridge 0000:00:1c.1 64bit mmio pref: [d1000000, d10fffff] 
[    0.469095] pci 0000:00:1e.0: transparent bridge 
[    0.469099] PCI: bridge 0000:00:1e.0 io port: [8000, 8fff] 
[    0.469120] bus 00 -> node 0 
[    0.469126] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] 
[    0.469378] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT] 
[    0.472052] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX1._PRT] 
[    0.472154] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT] 
[    0.480238] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 11 *12 14 15) 
[    0.480250] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 14 15) 
[    0.480354] ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 9 10 11 12 14 15) 
[    0.480456] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) 
[    0.480559] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled. 
[    0.480667] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled. 
[    0.480771] ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled. 
[    0.480875] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 *5 6 7 9 10 11 12 14 15) 
[    0.480929] Linux Plug and Play Support v0.97 (c) Adam Belay 
[    0.480929] pnp: PnP ACPI init 
[    0.480929] ACPI: bus type pnp registered 
[    0.484336] pnp: PnP ACPI: found 14 devices 
[    0.484336] ACPI: ACPI bus type pnp unregistered 
[    0.484336] PnPBIOS: Disabled by ACPI PNP 
[    0.484336] PCI: Using ACPI for IRQ routing 
[    0.492044] NET: Registered protocol family 8 
[    0.492049] NET: Registered protocol family 20 
[    0.492074] NetLabel: Initializing 
[    0.492074] NetLabel:  domain hash size = 128 
[    0.492074] NetLabel:  protocols = UNLABELED CIPSOv4 
[    0.492083] NetLabel:  unlabeled traffic allowed by default 
[    0.492092] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 
[    0.492100] hpet0: 3 64-bit timers, 14318180 Hz 
[    0.493538] tracer: 772 pages allocated for 65536 entries of 48 bytes 
[    0.493541]    actual entries 65620 
[    0.493632] AppArmor: AppArmor Filesystem Enabled 
[    0.493652] ACPI: RTC can wake from S4 
[    0.500089] system 00:01: ioport range 0x4d0-0x4d1 has been reserved 
[    0.500094] system 00:01: ioport range 0x290-0x29f has been reserved 
[    0.500099] system 00:01: ioport range 0x800-0x87f has been reserved 
[    0.500103] system 00:01: ioport range 0x290-0x294 has been reserved 
[    0.500108] system 00:01: ioport range 0x880-0x88f has been reserved 
[    0.500129] system 00:0a: ioport range 0x400-0x4bf could not be reserved 
[    0.500140] system 00:0b: iomem range 0xf0000000-0xf3ffffff could not be reserved 
[    0.500151] system 00:0c: iomem range 0xca800-0xcbfff has been reserved 
[    0.500156] system 00:0c: iomem range 0xf0000-0xf7fff could not be reserved 
[    0.500161] system 00:0c: iomem range 0xf8000-0xfbfff could not be reserved 
[    0.500166] system 00:0c: iomem range 0xfc000-0xfffff could not be reserved 
[    0.500171] system 00:0c: iomem range 0x3f7f0000-0x3f7fffff could not be reserved 
[    0.500176] system 00:0c: iomem range 0x0-0x9ffff could not be reserved 
[    0.500181] system 00:0c: iomem range 0x100000-0x3f7effff could not be reserved 
[    0.500187] system 00:0c: iomem range 0xfec00000-0xfec00fff could not be reserved 
[    0.500192] system 00:0c: iomem range 0xfed13000-0xfed1dfff could not be reserved 
[    0.500196] system 00:0c: iomem range 0xfed20000-0xfed8ffff could not be reserved 
[    0.500202] system 00:0c: iomem range 0xfee00000-0xfee00fff could not be reserved 
[    0.500207] system 00:0c: iomem range 0xffb00000-0xffb7ffff could not be reserved 
[    0.500212] system 00:0c: iomem range 0xfff00000-0xffffffff could not be reserved 
[    0.500217] system 00:0c: iomem range 0xe0000-0xeffff has been reserved 
[    0.500462] Switched to high resolution mode on CPU 1 
[    0.504060] Switched to high resolution mode on CPU 0 
[    0.535232] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:01 
[    0.535236] pci 0000:00:1c.0:   IO window: 0x9000-0x9fff 
[    0.535240] pci 0000:00:1c.0:   MEM window: disabled 
[    0.535244] pci 0000:00:1c.0:   PREFETCH window: disabled 
[    0.535251] pci 0000:00:1c.1: PCI bridge, secondary bus 0000:02 
[    0.535254] pci 0000:00:1c.1:   IO window: 0xa000-0xafff 
[    0.535259] pci 0000:00:1c.1:   MEM window: 0xd0000000-0xd0ffffff 
[    0.535263] pci 0000:00:1c.1:   PREFETCH window: 0x000000d1000000-0x000000d10fffff 
[    0.535269] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:03 
[    0.535272] pci 0000:00:1e.0:   IO window: 0x8000-0x8fff 
[    0.535277] pci 0000:00:1e.0:   MEM window: disabled 
[    0.535281] pci 0000:00:1e.0:   PREFETCH window: disabled 
[    0.535298] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 
[    0.535303] pci 0000:00:1c.0: setting latency timer to 64 
[    0.535310] pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 
[    0.535314] pci 0000:00:1c.1: setting latency timer to 64 
[    0.535321] pci 0000:00:1e.0: setting latency timer to 64 
[    0.535324] bus: 00 index 0 io port: [0, ffff] 
[    0.535326] bus: 00 index 1 mmio: [0, ffffffff] 
[    0.535328] bus: 01 index 0 io port: [9000, 9fff] 
[    0.535330] bus: 01 index 1 mmio: [0, 0] 
[    0.535332] bus: 01 index 2 mmio: [0, 0] 
[    0.535333] bus: 01 index 3 mmio: [0, 0] 
[    0.535335] bus: 02 index 0 io port: [a000, afff] 
[    0.535337] bus: 02 index 1 mmio: [d0000000, d0ffffff] 
[    0.535339] bus: 02 index 2 mmio: [d1000000, d10fffff] 
[    0.535341] bus: 02 index 3 mmio: [0, 0] 
[    0.535343] bus: 03 index 0 io port: [8000, 8fff] 
[    0.535344] bus: 03 index 1 mmio: [0, 0] 
[    0.535346] bus: 03 index 2 mmio: [0, 0] 
[    0.535348] bus: 03 index 3 io port: [0, ffff] 
[    0.535349] bus: 03 index 4 mmio: [0, ffffffff] 
[    0.535359] NET: Registered protocol family 2 
[    0.548111] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) 
[    0.548361] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) 
[    0.548839] TCP bind hash table entries: 65536 (order: 7, 524288 bytes) 
[    0.549176] TCP: Hash tables configured (established 131072 bind 65536) 
[    0.549180] TCP reno registered 
[    0.556168] NET: Registered protocol family 1 
[    0.556308] checking if image is initramfs... it is 
[    1.176783] Freeing initrd memory: 7994k freed 
[    1.177889] audit: initializing netlink socket (disabled) 
[    1.177912] type=2000 audit(1238156572.177:1): initialized 
[    1.183236] highmem bounce pool size: 64 pages 
[    1.183242] HugeTLB registered 4 MB page size, pre-allocated 0 pages 
[    1.185327] VFS: Disk quotas dquot_6.5.1 
[    1.185408] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) 
[    1.185503] msgmni has been set to 1762 
[    1.185618] io scheduler noop registered 
[    1.185620] io scheduler anticipatory registered 
[    1.185623] io scheduler deadline registered 
[    1.185634] io scheduler cfq registered (default) 
[    1.185649] pci 0000:00:02.0: Boot video device 
[    1.185820] pcieport-driver 0000:00:1c.0: setting latency timer to 64 
[    1.185851] pcieport-driver 0000:00:1c.0: found MSI capability 
[    1.185886] pci_express 0000:00:1c.0:pcie00: allocate port service 
[    1.185925] pci_express 0000:00:1c.0:pcie02: allocate port service 
[    1.186006] pcieport-driver 0000:00:1c.1: setting latency timer to 64 
[    1.186037] pcieport-driver 0000:00:1c.1: found MSI capability 
[    1.186069] pci_express 0000:00:1c.1:pcie00: allocate port service 
[    1.186106] pci_express 0000:00:1c.1:pcie02: allocate port service 
[    1.186382] isapnp: Scanning for PnP cards... 
[    1.539317] isapnp: No Plug & Play device found 
[    1.570430] Serial: 8250/16550 driver4 ports, IRQ sharing enabled 
[    1.570558] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 
[    1.571264] 00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 
[    1.573020] brd: module loaded 
[    1.573083] input: Macintosh mouse button emulation as /devices/virtual/input/input0 
[    1.573200] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1 
[    1.573202] PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp 
[    1.573341] serio: i8042 KBD port at 0x60,0x64 irq 1 
[    1.577202] mice: PS/2 mouse device common for all mice 
[    1.577325] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0 
[    1.577347] rtc0: alarms up to one month, hpet irqs 
[    1.577463] EISA: Probing bus 0 at eisa.0 
[    1.577488] Cannot allocate resource for EISA slot 8 
[    1.577490] EISA: Detected 0 cards. 
[    1.577494] cpuidle: using governor ladder 
[    1.577496] cpuidle: using governor menu 
[    1.577976] TCP cubic registered 
[    1.578003] Using IPI No-Shortcut mode 
[    1.578191] registered taskstats version 1 
[    1.578278]   Magic number: 1:106:381 
[    1.578399] rtc_cmos 00:03: setting system clock to 2009-03-27 12:22:53 UTC (1238156573) 
[    1.578402] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found 
[    1.578404] EDD information not available. 
[    1.578592] Freeing unused kernel memory: 424k freed 
[    1.578628] Write protecting the kernel text: 2576k 
[    1.578652] Write protecting the kernel read-only data: 936k 
[    1.595757] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1 
[    1.748054] fuse init (API version 7.9) 
[    1.792269] processor ACPI0007:00: registered as cooling_device0 
[    1.792274] ACPI: Processor [CPU0] (supports 8 throttling states) 
[    1.792452] ACPI: SSDT 3F7F7040, 0087 (r1  PmRef  Cpu1Ist     3000 INTL 20040311) 
[    1.886140] processor ACPI0007:01: registered as cooling_device1 
[    1.886145] ACPI: Processor [CPU1] (supports 8 throttling states) 
[    2.140731] usbcore: registered new interface driver usbfs 
[    2.140755] usbcore: registered new interface driver hub 
[    2.140793] usbcore: registered new device driver usb 
[    2.143152] USB Universal Host Controller Interface driver v3.0 
[    2.143203] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 
[    2.143212] uhci_hcd 0000:00:1d.0: setting latency timer to 64 
[    2.143215] uhci_hcd 0000:00:1d.0: UHCI Host Controller 
[    2.143260] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1 
[    2.143290] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000b400 
[    2.143428] usb usb1: configuration #1 chosen from 1 choice 
[    2.143453] hub 1-0:1.0: USB hub found 
[    2.143459] hub 1-0:1.0: 2 ports detected 
[    2.244294] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 
[    2.244304] uhci_hcd 0000:00:1d.1: setting latency timer to 64 
[    2.244308] uhci_hcd 0000:00:1d.1: UHCI Host Controller 
[    2.244339] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2 
[    2.244370] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000b800 
[    2.244455] usb usb2: configuration #1 chosen from 1 choice 
[    2.244482] hub 2-0:1.0: USB hub found 
[    2.244488] hub 2-0:1.0: 2 ports detected 
[    2.276322] No dock devices found. 
[    2.318746] SCSI subsystem initialized 
[    2.348363] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 
[    2.348373] uhci_hcd 0000:00:1d.2: setting latency timer to 64 
[    2.348376] uhci_hcd 0000:00:1d.2: UHCI Host Controller 
[    2.348409] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3 
[    2.348440] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000bc00 
[    2.348534] usb usb3: configuration #1 chosen from 1 choice 
[    2.348562] hub 3-0:1.0: USB hub found 
[    2.348569] hub 3-0:1.0: 2 ports detected 
[    2.378389] libata version 3.00 loaded. 
[    2.452373] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16 
[    2.452385] uhci_hcd 0000:00:1d.3: setting latency timer to 64 
[    2.452389] uhci_hcd 0000:00:1d.3: UHCI Host Controller 
[    2.452419] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4 
[    2.452453] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000c000 
[    2.452559] usb usb4: configuration #1 chosen from 1 choice 
[    2.452586] hub 4-0:1.0: USB hub found 
[    2.452594] hub 4-0:1.0: 2 ports detected 
[    2.661360] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23 
[    2.661374] ehci_hcd 0000:00:1d.7: setting latency timer to 64 
[    2.661377] ehci_hcd 0000:00:1d.7: EHCI Host Controller 
[    2.661402] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5 
[    2.665294] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported 
[    2.665302] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xd11c4000 
[    2.776043] usb 4-1: new low speed USB device using uhci_hcd and address 2 
[    2.784068] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 
[    2.784258] usb usb5: configuration #1 chosen from 1 choice 
[    2.784289] hub 5-0:1.0: USB hub found 
[    2.784297] hub 5-0:1.0: 8 ports detected 
[    2.840054] hub 4-0:1.0: unable to enumerate USB device on port 1 
[    2.992285] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded 
[    2.992300] r8169 0000:02:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 
[    2.992317] r8169 0000:02:00.0: setting latency timer to 64 
[    2.992627] eth0: RTL8168c/8111c at 0xf8834000, 00:1f:d0:18:73:01, XID 3c4000c0 IRQ 221 
[    2.997039] pata_acpi 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19 
[    2.997066] pata_acpi 0000:00:1f.2: setting latency timer to 64 
[    2.997077] pata_acpi 0000:00:1f.2: PCI INT B disabled 
[    3.000603] ata_piix 0000:00:1f.2: version 2.12 
[    3.000612] ata_piix 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19 
[    3.000616] ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ] 
[    3.000647] ata_piix 0000:00:1f.2: setting latency timer to 64 
[    3.000703] scsi0 : ata_piix 
[    3.000792] scsi1 : ata_piix 
[    3.001457] ata1: SATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14 
[    3.001460] ata2: SATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15 
[    3.176221] ata1.00: HPA unlocked: 156299375 -> 156301488, native 156301488 
[    3.176227] ata1.00: ATA-7: Hitachi HDS721680PLA380, P21OABEA, max UDMA/133 
[    3.176229] ata1.00: 156301488 sectors, multi 16: LBA48 NCQ (depth 0/32) 
[    3.188418] ata1.00: configured for UDMA/133 
[    3.344162] ata2.01: NODEV after polling detection 
[    3.352212] ata2.00: ATAPI: TSSTcorp CDDVDW SH-S223F, SB00, max UDMA/100 
[    3.368074] usb 4-1: new low speed USB device using uhci_hcd and address 3 
[    3.368225] ata2.00: configured for UDMA/100 
[    3.368338] scsi 0:0:0:0: Direct-Access     ATA      Hitachi HDS72168 P21O PQ: 0 ANSI: 5 
[    3.369021] scsi 1:0:0:0: CD-ROM            TSSTcorp CDDVDW SH-S223F  SB00 PQ: 0 ANSI: 5 
[    3.374916] scsi 0:0:0:0: Attached scsi generic sg0 type 0 
[    3.374952] scsi 1:0:0:0: Attached scsi generic sg1 type 5 
[    3.384922] Driver 'sd' needs updating - please use bus_type methods 
[    3.385020] sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB) 
[    3.385036] sd 0:0:0:0: [sda] Write Protect is off 
[    3.385038] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 
[    3.385064] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA 
[    3.385128] sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB) 
[    3.385142] sd 0:0:0:0: [sda] Write Protect is off 
[    3.385145] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 
[    3.385171] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA 
[    3.385175]  sda:<4>Driver 'sr' needs updating - please use bus_type methods 
[    3.403473]  sda1 sda2 < sda5 sda6 > 
[    3.435928] sd 0:0:0:0: [sda] Attached SCSI disk 
[    3.446997] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray 
[    3.447002] Uniform CD-ROM driver Revision: 3.20 
[    3.447089] sr 1:0:0:0: Attached scsi CD-ROM sr0 
[    3.567679] usb 4-1: configuration #1 chosen from 1 choice 
[    3.589592] usbcore: registered new interface driver hiddev 
[    3.628783] input: HID 1241:1111 as /devices/pci0000:00/0000:00:1d.3/usb4/4-1/4-1:1.0/input/input2 
[    3.629062] input,hidraw0: USB HID v1.10 Mouse [HID 1241:1111] on usb-0000:00:1d.3-1 
[    3.629081] usbcore: registered new interface driver usbhid 
[    3.629085] usbhid: v2.6:USB HID core driver 
[    3.775876] PM: Starting manual resume from disk 
[    3.775880] PM: Resume from partition 8:6 
[    3.775882] PM: Checking hibernation image. 
[    3.776222] PM: Resume from disk failed. 
[    3.823920] kjournald starting.  Commit interval 5 seconds 
[    3.823946] EXT3-fs: mounted filesystem with ordered data mode. 
[    8.349125] udevd version 124 started 
[    8.578231] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 
[    8.662583] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 
[    8.768606] Linux agpgart interface v0.103 
[    8.815539] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3 
[    8.837056] ACPI: Power Button (FF) [PWRF] 
[    8.837147] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input4 
[    8.869036] ACPI: Power Button (CM) [PWRB] 
[    8.890063] agpgart-intel 0000:00:00.0: Intel 945G Chipset 
[    8.890316] agpgart-intel 0000:00:00.0: detected 7932K stolen memory 
[    8.905303] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xc0000000 
[    9.019224] parport_pc 00:08: reported by Plug and Play ACPI 
[    9.019269] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE] 
[    9.131901] iTCO_vendor_support: vendor-support=0 
[    9.158694] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008) 
[    9.166483] iTCO_wdt: Found a ICH7 or ICH7R TCO device (Version=2, TCOBASE=0x0460) 
[    9.166580] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0) 
[    9.205759] intel_rng: FWH not detected 
[    9.394407] input: PC Speaker as /devices/platform/pcspkr/input/input5 
[    9.438002] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 
[    9.438020] HDA Intel 0000:00:1b.0: setting latency timer to 64 
[    9.470922] hda_codec: Unknown model for ALC662, trying auto-probe from BIOS... 
[   11.330067] lp0: using parport0 (interrupt-driven). 
[   11.449979] Adding 1662688k swap on /dev/sda6.  Priority:-1 extents:1 across:1662688k 
[   12.000748] EXT3 FS on sda5, internal journal 
[   12.923336] type=1505 audit(1238156584.690:2): operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" name2="default" pid=3965 
[   13.074482] type=1505 audit(1238156584.841:3): operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" name2="default" pid=3970 
[   13.074683] type=1505 audit(1238156584.841:4): operation="profile_load" name="/usr/sbin/cupsd" name2="default" pid=3970 
[   13.191122] ip_tables: (C) 2000-2006 Netfilter Core Team 
[   13.690553] ACPI: WMI: Mapper loaded 
[   14.474697] warning: `avahi-daemon' uses 32-bit capabilities (legacy support in use) 
[   14.526175] apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac) 
[   14.526180] apm: disabled - APM is not SMP safe. 
[   14.693316] ppdev: user-space parallel port driver 
[   15.751692] Bluetooth: Core ver 2.13 
[   15.753233] NET: Registered protocol family 31 
[   15.753242] Bluetooth: HCI device and connection manager initialized 
[   15.753249] Bluetooth: HCI socket layer initialized 
[   15.770545] Bluetooth: L2CAP ver 2.11 
[   15.770553] Bluetooth: L2CAP socket layer initialized 
[   15.786045] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 
[   15.786053] Bluetooth: BNEP filters: protocol multicast 
[   15.819462] Bridge firewalling registered 
[   15.819668] pan0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature. 
[   15.834988] Bluetooth: SCO (Voice Link) ver 0.6 
[   15.834996] Bluetooth: SCO socket layer initialized 
[   15.902001] Bluetooth: RFCOMM socket layer initialized 
[   15.902023] Bluetooth: RFCOMM TTY layer initialized 
[   15.902026] Bluetooth: RFCOMM ver 1.10 
[   18.773166] [drm] Initialized drm 1.1.0 20060810 
[   18.835265] pci 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 
[   18.835279] pci 0000:00:02.0: setting latency timer to 64 
[   18.837883] [drm] Initialized i915 1.6.0 20060119 on minor 0 
[   20.021702] r8169: eth0: link up 
[   20.021717] r8169: eth0: link up 
[   20.483973] NET: Registered protocol family 17 
[   89.306664] r8169 0000:02:00.0: PCI INT A disabled 
[  111.301145] type=1503 audit(1238156683.070:5): operation="inode_permission" requested_mask="r::" denied_mask="r::" fsuid=7 name="/proc/5539/net/" pid=5539 profile="/usr/sbin/cupsd" 
[  111.399810] NET: Registered protocol family 10 
[  111.401582] lo: Disabled Privacy Extensions 
[  111.403779] type=1503 audit(1238156683.171:6): operation="socket_create" family="ax25" sock_type="dgram" protocol=0 pid=5539 profile="/usr/sbin/cupsd" 
[  111.404274] type=1503 audit(1238156683.171:7): operation="socket_create" family="netrom" sock_type="seqpacket" protocol=0 pid=5539 profile="/usr/sbin/cupsd" 
[  111.404746] type=1503 audit(1238156683.171:8): operation="socket_create" family="rose" sock_type="dgram" protocol=0 pid=5539 profile="/usr/sbin/cupsd" 
[  111.405203] type=1503 audit(1238156683.175:9): operation="socket_create" family="ipx" sock_type="dgram" protocol=0 pid=5539 profile="/usr/sbin/cupsd" 
[  111.405665] type=1503 audit(1238156683.175:10): operation="socket_create" family="appletalk" sock_type="dgram" protocol=0 pid=5539 profile="/usr/sbin/cupsd" 
[  111.406136] type=1503 audit(1238156683.175:11): operation="socket_create" family="econet" sock_type="dgram" protocol=0 pid=5539 profile="/usr/sbin/cupsd" 
[  111.406597] type=1503 audit(1238156683.175:12): operation="socket_create" family="ash" sock_type="dgram" protocol=0 pid=5539 profile="/usr/sbin/cupsd" 
[  111.407051] type=1503 audit(1238156683.175:13): operation="socket_create" family="x25" sock_type="seqpacket" protocol=0 pid=5539 profile="/usr/sbin/cupsd" 
[  111.407606] type=1503 audit(1238156683.175:14): operation="inode_permission" requested_mask="::r" denied_mask="::r" fsuid=7 name="/proc/5539/net/dev" pid=5539 profile="/usr/sbin/cupsd" 
[  112.268321] ppdev0: registered pardevice 
[  112.316203] ppdev0: unregistered pardevice 
[  113.396175] ppdev0: registered pardevice 
[  113.444355] ppdev0: unregistered pardevice 
[  113.456315] ppdev0: registered pardevice 
[  113.505031] ppdev0: unregistered pardevice 
[  117.078530] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded 
[  117.078559] r8169 0000:02:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 
[  117.078582] r8169 0000:02:00.0: setting latency timer to 64 
[  117.081454] eth0: RTL8168c/8111c at 0xf8836000, 00:1f:d0:18:73:01, XID 3c4000c0 IRQ 221 
[  121.098879] r8169: eth0: link up 
[  121.098895] r8169: eth0: link up

**coutts99** · March 27th, 2009

Can you send ifconfig output again?

Can you ping your default gateway?

**DancinHomer** · March 27th, 2009

Code:

eth0      Link encap:Ethernet  HWaddr 00:1f:d0:18:73:01  
          UP BROADCAST RUNNING MULTICAST  MTU:64  Metric:1 
          RX packets:25 errors:0 dropped:3985147215 overruns:0 frame:0 
          TX packets:12 errors:0 dropped:0 overruns:0 carrier:0 
          collisions:0 txqueuelen:1000 
          RX bytes:5018 (5.0 KB)  TX bytes:2665 (2.6 KB) 
          Interrupt:221 Base address:0x6000 

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0 
          inet6 addr: ::1/128 Scope:Host 
          UP LOOPBACK RUNNING  MTU:16436  Metric:1 
          RX packets:240 errors:0 dropped:0 overruns:0 frame:0 
          TX packets:240 errors:0 dropped:0 overruns:0 carrier:0 
          collisions:0 txqueuelen:0 
          RX bytes:15040 (15.0 KB)  TX bytes:15040 (15.0 KB)

I'm using the ping tool from the Network Tool utility and it doesn't seem to ping - I click on ping and nothing happens (all statistics read 0)

Thread: All seems okay, but cannot access internet >

Thread Tools

Display

All seems okay, but cannot access internet > SOLVED

Re: All seems okay, but cannot access internet >

Re: All seems okay, but cannot access internet >

Re: All seems okay, but cannot access internet >

Re: All seems okay, but cannot access internet >

Re: All seems okay, but cannot access internet >

Re: All seems okay, but cannot access internet >

Re: All seems okay, but cannot access internet >

Re: All seems okay, but cannot access internet >

Re: All seems okay, but cannot access internet >

Bookmarks

Bookmarks

Posting Permissions