You can NAT public or private IPs.
You'll need is setup a router/firewall with your public IP
subnet. Then with firewall rules and NAT you can forward
specific ports to each server based on the...
Type: Posts; User: volkswagner; Keyword(s):
You can NAT public or private IPs.
You'll need is setup a router/firewall with your public IP
subnet. Then with firewall rules and NAT you can forward
specific ports to each server based on the...
Are you hiding part of the netplan cfg file?
Are there any other interfaces on the Ubuntu VM?
Why did you need to specify a mac address in the yml file?
Are there any relevant entries in the...
There's no link to your tutorial and you have not provided any configuration information.
Did you enable IP forwarding?
Do you have NAT/Firewall rules set up?
Since your VMs appear on your Local LAN, you should be able to do as
@TheFu suggested (leave the Bridge interface unconfigured/no IP address).
I've never set up an interface without an IP, so I...
I'd love to help but you've missed some questions.
Do you plan on providing internet to the VM’s?
Please provide your goals and network topology (will the NUC be connected to multiple networks, if you are providing Internet to the VM’s is via your...
Sounds like the iPad is communicating directly to the printer (Wifi - Direct).
Have you tried the good ole pull the power plug on the printer, wait 10 seconds
and plug it back in?
I'm sure sure I'm much help here. I'm just guessing.
Perhaps try adding (inside the [vpn] section):
ike=aes256-sha256-modp2048
esp=aes256-sha256-modp2048
It's hard to say. I never used the gui. When you make changes in the gui, do you
see them reflected in the config files?
Can you post the contents of the config file and protect private items
like...
The function of the bridge is dependent upon which interfaces are included (plus firewall and routing). If a bridge is created without including the local LAN interface, how does that help your...
I'm no expert, but I know the settings need to match on both ends.
You need to configure StrongSwan with Diffie Hellman Groups to
be the same value on each side. It looks like your router can't...
I’m not familiar with DrayTek. It looks like you’ve put username in the identity field. Identity would be = remote ID.
The specific error is regarding DH group. I don’t see DH group setting in...
It seems like running from Wi-Fi card is not contributing to the issue. I’ll add to the other suggestions in case using the LAN port would be better. There are Wi-Fi routers or access points that can...
I finally get some help from ##strongswan.
I had to change the order of my NAT rules.
Traffic was not recognized by the ipsec policy
because it was hitting NAT rules too early.
Here's the...
I've used this guide with great success, including Airprint (using
a usb only printer).
I'm curious if the issues cthog had were due to using fdisk on a GPT partitioned disk.
I believe fdisk currently supports GPT, but I think early versions of fdisk did not.
What's the installed...
Perhaps offer a description of what you'd like to accomplish.
It's possible using two .yaml files for the same interface
is not the best way to offer a "failback" or redundancy?
Is this for...
Greetings,
I'm struggling with setting up Strongswan IPsec VPN between home and cloud
hosted hardware server acting as KVM host.
The host is running 20.04 server with KVM and Strongswan.
Home...
Thanks, LHammonds and TheFu.
Now I know why nobody could tell me why a user's crontab was executing/changing the user as root.
Well, it wasn't and it doesn't.
Looking at LHammonds one-liner in...
Thanks for your reply TheFu.
I think my question remains, "why is a user's crontab, trying to connect to the remote server as root".
The cron job clearly runs as the user "eric" as seen in...
I'm not sure how to word the title.
My google foo hasn't yielded any explanation.
I'm trying to "pull" a backup from a remote server.
On the server running the script, I created a script...
I’m no expert. I’ve only created LVM physical volumes on top of RAID. Looking at your commands it seems logical to me your LVM with missing disk causes fatal error. The PV is missing a member.
...
Try some other tools like traceroute and post your routing table.
You may want to look into ACPI Wake.
I remember using it years ago with MythTV.
https://www.mythtv.org/wiki/ACPI_Wakeup
You’ll want VPN (site to site) to make it secure.