Hi guyz, am kinda new to linux, i need advice on how to create a p2p stream server for live and vod, do broadcast internet tv on a multicast network, any assistance, i will highly appreciate...
...
Type: Posts; User: kanjah; Keyword(s):
Hi guyz, am kinda new to linux, i need advice on how to create a p2p stream server for live and vod, do broadcast internet tv on a multicast network, any assistance, i will highly appreciate...
...
thank you cheesemill,
hi cheesemill, how will i deploy the webmin in the server and yet i dnt have a browser?
thanks dino99, al follow the link you gave
Hi mates, am trying to install a gui for my ubuntu server 64, so that i can install webmin, to monitor and manage the squid proxy, but i encouter, problems whilst doing it., i used
apt-get...
thanks seiji sensi, i followed the link and all is well
Hi guyz, i have sucesfully installed squid3 3.1.20 64bit, and all is well. when i run the cache.log i get this error
intercept.cc(137) Netfilter Interception: NF getsockopt(SO_ORIGINAL_DST) faile...
hi mates, am currently using squid3 3.1.20 64 bit on ubuntu server 12tty 64 bit, i have a problem with my refresh rate, which prevents squid3 to start, here's a sample code that am using
...
i did, but it still displays the same.....it allows access
i have, that was a typo
hi mates, am currently running squid 3.1.20, 64 bit on hpz800 as transparent. All is well except the server doesn't block any address that i have specified, here'z my sample code
acl bad_site...
Hi guyz, i have hp z800, running on ubuntu 12 amg64, wth two onboard NIC (eth1 and p1p1), the problem is that pinging p1p1 gives high latency and after a restart the p1p1(as shown when i run lshw -C...
thanks papibe, from the sudo lshw -C network, i found the other eth interface to be disabled, i enabled it and all is well, thank you again
Hi guyz, i have a hp z800, running ubuntu server 12amg 64, with 2 on board NIC, the system seems to pick one and ignore the other, i have searched it in /etc/networks/interfaces, seems not to be...
I did edit the GRUB_CMDLINE_LINUX_DEFAULT add the line at the end="quiet drm_kms_helper.poll=0".since i could not edit the file due to the multiple error display, i copied the file to a flash disk...
Hi grahammechanical, thanks for the reply, how do i log on into fail safe?
hi chessmill, {drm} nouveau 0000:28:00.0: no native mode, forcing panel scaling
is the error that i get, when i try to edit the GRUB_CMDLINE_LINUX_DEFAULT, the {drm} nouveau 0000:28:00.0: no native...
hi chessmill, am tying to add "quiet drm_kms_helper.poll=0", editing it normall seems hard since i get a continious error message
Hi brent1975, tried it without the rw, the system is still in read only mode, even after restart
Hi cheesemill, thanks for the reply, tried the mount -o rw, remount /, the condition is still the same, do i need put another command after this?
Hi guyz, ave installed ubuntu server 12amg64, i need to boot in recovery mode so as to make change on the /etc/default/grub file, but in recovery mode i have only read privileges, i have tried using...
Hi guyz, just installed ubuntu server 12 amd64 on hp z800 workstation, to be used as a proxy server. I has 32 gb ddr3 ram, 2x3.0 xeon processor, tesla nvida media card, and 2tb space. At the login...
hi, am running as root, ave tried using find, but i dnt seem to find the deb file
hi guyz, am kinda new to ubuntu, i really need help, ave downloaded deb file using
wget http://www.dmasoftlab.com/cont/download/libltdl3_1.5.24-1ubuntu1_i386.deb
but if i run
dpkg -i...
Hi guyz, i have installed squid3 and would want to change its default icon to my own, i have one png hosted on imageshack, did refer to it on squid errorpage.css
"background:...