There is no password, but password is required to unlock, you can press switch user and then you can login and end up on a inf. loading screen (Ctrl+Alt+F2 to get back)
you can manually lock via...
Type: Posts; User: pqwoerituytrueiwoq; Keyword(s):
There is no password, but password is required to unlock, you can press switch user and then you can login and end up on a inf. loading screen (Ctrl+Alt+F2 to get back)
you can manually lock via...
I have a HL-L2360DW and have the same experience as SeijiSensei using a wired connection, my Mom has a HLL2300D (USB only) and it is a PITA every time i print i have to hit the power button i think...
you could edit the wav file in audacity and amplify it or you can use amixer and get the current volume, set the volume, the play the file then set the volume back
The sata controller i am using is not the ideal chipset, so i think it is VERY VERY picky and my box is not the best for EMI... i have a cable modem, boost converter, audio amp, and 5 port switch in...
For the purpose of expansion and having different permissions on each folder on the partition
in other news...
pool: mypool
state: ONLINE
status: One or more devices has experienced an...
Fine i'll just use symbolic links...
$ zfs list
NAME USED AVAIL REFER MOUNTPOINT
mypool 31.0G 7.09T 30.9G /spinningRust
$ cat /etc/fstab
# /etc/fstab:...
$ sudo zfs list mypool
NAME USED AVAIL REFER MOUNTPOINT
mypool 31.0G 7.09T 30.9G /mnt/HDD
$ ls /mnt/HDD/
apt-cacher-ng testDir www
the data is 100% on the ZFS array's...
note the issue seems to be my binds in /etc/fstab, disabling them made the system happy, these binds are linked to my zfs array
No i have 3 arrays
2 are in md using raid1 (/ and /mnt/Data)
1 is...
mypool mountpoint /mnt/HDD local
$ cat /proc/mounts
sysfs /sys sysfs rw,nosuid,nodev,noexec,relatime 0 0
proc /proc proc rw,nosuid,nodev,noexec,relatime 0 0
udev...
found the cause in my fstab file
#/mnt/HDD/www /var/www bind x-systemd.after=zfs-mount.service,x-systemd.requires=/mnt/HDD,defaults,bind 0 0
#/mnt/HDD/www ...
now the issue is worse and i have my WTR54GL out
my md array for / is read-only as a result nothing is working
xubuntu@xubuntu:~$ cat /proc/mdstat
Personalities : [raid1]
md1 : active...
this morning i noted some errors in my array from, but i was able to pass a scrub so i cleared it and the drive shows good in SMART, if i have ANOTHER bad sata cable... anyone know where i can get...
the instructions in post #3 are for use on a live session, I am not sure what needs to be omitted to run them on a normal session
yes if i can't boot my server i have no internet access (well...
so a power outage will cause this to happen? can i automate a repair attempt? (having to use a live GUI session on a headless server is no fun)
right now the server is booted and running, i should...
Power when out, UPS battery ran out of power, power was lost
BIOS powered up when power was restored, but the system was waiting on user input (Ctrl+D to continue) before it started my VM...
installed kubuntu just now and i did not get/notice a minimal option, the install icon and installer do show 23.10
https://cdimage.ubuntu.com/kubuntu/daily-live/current/
i know a reboot is required, i have been using these options for years now (since Nov 26 2021) and suddenly it was not working a as of a few days ago
$ uptime
23:28:49 up 56 days, 16:24, 10...
looks like it was changed to enabled?
cat /sys/module/snd_hda_intel/parameters/power_save
1
In-spite of my config file last being edited since Nov 26 2021 (the install date the OS)
From my /etc/modprobe.d/alsa-base.conf file
# https://bbs.archlinux.org/viewtopic.php?pid=1766206#p1766206
options snd_hda_intel power_save=0
options snd_hda_intel power_save=0...
no GPS, the server just syncs with the default time servers, i did this so all my PICOs that care about the time can get the time from a the local network (better then hoping the internet is working...
so about this:
sudo timedatectl set-ntp off
Failed to set ntp: NTP not supported
i had to install systemd-timesyncd to make that work, now i can toggle the checkbox in the GUI
does the ntp...
running kubuntu 22.04 and i noticed my clock is about 20 seconds or so off
I have a local ntp server that is up and running, but i need to know how to enable it and config it to use my server
...
i just go and read my code
Examples of how bad i am about comments
https://github.com/GM-Script-Writer-62850/PICO_W_Thermostat/blob/main/PICO/main.py...
i rarely comment my code, and when i do it is cause it is VERY confusing to read, unless it is a config file, then i will put notes in it
I found it... thanks Paddy for solving issue of my own creation...
$ type date
date is aliased to `date +"%A %B %d, %I:%M %p"'
wait what!? why...
*reads .bash_aliases*
why did i do that?...