Time not kept on NTP server
I try to have one NTP-server on my network and have others synchronize with it.
I installed NTP on one (fysical) server and tried various variations of /etc/ntp.conf which all lead to the following:
- I stop NTP.
- set my time with ntpdate from one of the timeservers
- I start NTP
- My server runs the correct time for a couple of minutes, and then jumps 257.3 seconds backwards and keeps this distance to the timeservers.
- I stop NTP .... set time ... start NTP 15 minutes later.... 257.3 seconds in the past.... etc...
The clients follow the server-time or find huge offsets depending on whether they use only this or other timeservers as well.
Also when I don't start NTP, my server falls back about 257 seconds somewhere within 10 minutes and stays there. I did set the hardware-clock with hwclock --systohc to a 'propper' time, but this did not influence the behavior.
Anyone got a clue? I am out of them. After a wile, ntpdc -p reads:
in which 192.168.34.255 is my local subnet.
remote local st poll reach delay offset disp
*ipv6.net 192.168.34.90 2 64 377 0.03630 257.51047 0.03069
=europium.canoni 192.168.34.90 2 64 377 0.01447 257.52319 0.03081
=nfs01.ip2.net 192.168.34.90 3 64 377 0.03232 257.48066 0.03059
^192.168.34.255 192.168.34.95 16 64 0 0.00000 0.000000 4.00000
=ntp.networking4 192.168.34.90 2 64 377 0.02934 257.51364 0.03061
=ntp0.mediamatic 192.168.34.90 2 64 377 0.02516 257.51202 0.03073
Thanks for reading,
p.s. This is the last ntp.conf I used
# /etc/ntp.conf, configuration for ntpd; see ntp.conf(5) for help
# Enable this if you want statistics to be logged.
statistics loopstats peerstats clockstats
filegen loopstats file loopstats type day enable
filegen peerstats file peerstats type day enable
filegen clockstats file clockstats type day enable
# You do need to talk to an NTP server or two (or three).
server 0.debian.pool.ntp.org iburst
server 1.debian.pool.ntp.org iburst
server 2.debian.pool.ntp.org iburst
server 3.debian.pool.ntp.org iburst
# Access control configuration; see /usr/share/doc/ntp-doc/html/accopt.html for
# details. The web page <http://support.ntp.org/bin/view/Support/AccessRestrictions>
# might also be helpful.
# Note that "restrict" applies to both servers and clients, so a configuration
# that might be intended to block requests from certain clients could also end
# up blocking replies from your own upstream servers.
# By default, exchange time with everybody, but don't allow configuration.
restrict -4 default kod notrap nomodify nopeer noquery
restrict -6 default kod notrap nomodify nopeer noquery
# Local users may interrogate the ntp server more closely.
# Clients from this (example!) subnet have unlimited access, but only if
# cryptographically authenticated.
#restrict 192.168.123.0 mask 255.255.255.0 notrust
#restrict 192.168.34.0 mask 255.255.255.0 nomodify notrap
# If you want to provide time to your local subnet, change the next line.
# (Again, the address is an example only.)
# If you want to listen to time broadcasts on your local subnet, de-comment the
# next lines. Please do this only if you trust everybody on the network!