Hi all,
I followed the howto (thank to you Luca).
After a little fight with the old version of the driver, I finally get this after a reboot:
Code:
[domo@Xmas:~ $ dmesg | grep ipw
ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.0.3
ipw2200: Copyright(c) 2003-2004 Intel Corporation
ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
But, when I launched the wpa_supplicant, I get this loop
Code:
domo@Xmas:~ $ sudo wpa_supplicant -i eth1 -c /etc/wpa_supplicant.conf -D ipw -w -dd
Initializing interface 'eth1' conf '/etc/wpa_supplicant.conf' driver 'ipw'
Configuration file '/etc/wpa_supplicant.conf' -> '/etc/wpa_supplicant.conf'
Reading configuration file '/etc/wpa_supplicant.conf'
Line: 1 - start of a new network block
ssid - hexdump_ascii(len=7):
72 61 62 61 6c 69 6e rabalin
proto: 0x1
scan_ssid=1 (0x1)
key_mgmt: 0x2
PSK - hexdump(len=32): [REMOVED]
Priority group 0
id=0 ssid='rabalin'
Initializing interface (2) 'eth1'
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
wpa_driver_ipw_init is called
Own MAC address: 00:0e:35:26:aa:bb
wpa_driver_ipw_set_wpa: enabled=1
wpa_driver_ipw_set_key: alg=none key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_ipw_set_key: alg=none key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_ipw_set_key: alg=none key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_ipw_set_key: alg=none key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_ipw_set_countermeasures: enabled=0
wpa_driver_ipw_set_drop_unencrypted: enabled=1
Setting scan request: 0 sec 100000 usec
Wireless event: cmd=0x8b06 len=8
RTM_NEWLINK, IFLA_IFNAME: Interface 'eth1' added
RTM_NEWLINK, IFLA_IFNAME: Interface 'eth1' added
Starting AP scan (specific SSID)
Scan SSID - hexdump_ascii(len=7):
72 61 62 61 6c 69 6e rabalin
ioctl[SIOCSIWSCAN{,EXT}]: Operation not supported
Failed to initiate AP scan.
Setting scan request: 10 sec 0 usec
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
Scan timeout - try to get results
Received 0 bytes of scan results (0 BSSes)
Scan results: 0
Selecting BSS from priority group 0
No suitable AP found.
Setting scan request: 5 sec 0 usec
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
Starting AP scan (broadcast SSID)
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
Scan timeout - try to get results
Received 0 bytes of scan results (0 BSSes)
Scan results: 0
Selecting BSS from priority group 0
No suitable AP found.
.....
the strange think is that I set the mode as ad-hoc, and after running wpa_supplicant the mode is unset
Code:
domo@Xmas:~ $ sudo iwconfig eth1
eth1 unassociated ESSID:"rabalin" Nickname:"domo_node"
Mode:Managed Channel=0 Access Point: 00:00:00:00:00:00
Bit Rate=0 kb/s Tx-Power=20 dBm
RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
Did wpa_supplicant don't support the ad-hoc mode ? or did I miss something ?
(forgive my poor english as well :) )