12.10 - Extended Desktop - How to change virtual desktop size?
Running: Ubuntu Studio 12.10
Platform: Acer Aspire One AO751h
Screen: 1366x768
Video: Integrated Intel Graphics Media Accelerator 500
with Dual Monitor:
Monitor: AOC 22
Res: 1920x1080
Ran: $ xrandr --output VGA-0 --mode 1920x1080 --right-of LVDS-0
Got: $ xrandr: screen cannot be larger than 2048x2048 (desired size 3286x1080)
There is no initial xorg.conf file to edit and they changed the location /xorg.conf.d/ to /usr/share/X11 in 12.10.
Please advise me on the best way to get the virtual display (extended desktop) running properly. I use this setup for work and any help would be appreciated :)
Re: 12.10 - Extended Desktop - How to change virtual desktop size?
Another method that I tried today yielded the same result, that was:
$ xrandr --output LVDS-0 --mode 1366x768 --output VGA-0 --mode 1920x1080 --right-of LVDS-0
Tried with (sudo) root, still got the same message:
$ xrandr: screen cannot be larger than 2048x2048 (desired size 3286x1080)
I've been reading through setting up xorg.conf files today, none of the methods I've been finding on the forum have been working (they worked fine for my 10.04 LTS install, but unfortunately, Ubuntu updated itself and that system crashed).
Looking forward to some help - thanks!
Re: 12.10 - Extended Desktop - How to change virtual desktop size?
I think your intel graphics is limited to 2Kx2K because you are not using the proprietary driver..
The GMA500 is a nasty intel GPU designed by PowerVR SGX (Poulsbo)
The best driver is not open source.
Most of the intel GPUs are supported by the free open source drivers with support of intel but not GMA500 or Cedartrail.
glxinfo | grep OpenGL
post the /var/log/Xorg.0.log file
Re: 12.10 - Extended Desktop - How to change virtual desktop size?
Here is a copy of the previous xorg.conf file that worked:
Code:
Section "Device"
Identifier "Videocard0"
Driver "psb"
Option "IgnoreACPI"
EndSection
Section "Extensions"
Option "Composite" "Enable"
EndSection
Section "Screen"
Identifier "screen1"
Device "Videocard0"
DefaultColorDepth 24
Subsection "Display"
Depth 24
Virtual 3286 1828
EndSubsection
EndSection
However, when placed in /etc/X11/, the system will not boot - again, worked fine under 10.04 LTS, but does not work under 12.10.
I made sure to run:
Code:
sudo chmod 755 xorg.conf
As well ...
Other information;
$ lsmod | grep gma shows;
Code:
Gma500_gfx 187730 1
drm_kms_helper 45271 1 gma500_gfx
drm 226367 3 gma500_gfx,drm_kms_helper
i2c_algo_bit 13197 1 gma500_gfx
video 18847 2 acer_wmi,gma500_gfx
and,
$ lspci | grep VGA shows;
Code:
00:02.0 VGA compatible controller: Intel Corporation System Controller Hub (SCH Poulsbo) Graphics Controller (rev 07)
Stated, I placed a file specific to the video card's driver here :
/usr/share/X11/xorg.conf.d/20-gpudriver.conf
Code:
Section "Device" Identifier "gma500_gfx" Driver "modesetting" Option "SWCursor" "ON" EndSection
While this did not keep the system from booting up, even with this setting, XRandR
still returned:
xrandr: screen cannot be larger than 2048x2048 (desired size 3286x1080)
I've tried as much as I can, please help if you know of any other options.
Re: 12.10 - Extended Desktop - How to change virtual desktop size?
Quote:
Originally Posted by
BicyclerBoy
I think your intel graphics is limited to 2Kx2K because you are not using the proprietary driver..
The GMA500 is a nasty intel GPU designed by PowerVR SGX (Poulsbo)
The best driver is not open source.
Most of the intel GPUs are supported by the free open source drivers with support of intel but not GMA500 or Cedartrail.
glxinfo | grep OpenGL
post the /var/log/Xorg.0.log file
When I ran glxinfo, I had to install mesa-utils
Anyway, here is the return:
Code:
OpenGL vendor string: VMware, Inc.
OpenGL renderer string: Gallium 0.4 on llvmpipe (LLVM 0x301)
OpenGL version string: 2.1 Mesa 9.0
OpenGL shading language version string: 1.20
OpenGL extensions
here is the return from /var/log/Xorg.0.log file
Code:
[ 18.575]
X.Org X Server 1.13.0
Release Date: 2012-09-05
[ 18.575] X Protocol Version 11, Revision 0
[ 18.575] Build Operating System: Linux 3.2.0-26-generic i686 Ubuntu
[ 18.575] Current Operating System: Linux tsani-top 3.5.0-17-lowlatency #18-Ubuntu SMP PREEMPT Tue Oct 9 20:05:16 UTC 2012 i686
[ 18.576] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.5.0-17-lowlatency root=UUID=141b3433-b441-4d95-9362-eccd3aa91713 ro quiet splash vt.handoff=7
[ 18.576] Build Date: 08 October 2012 03:34:08PM
[ 18.576] xorg-server 2:1.13.0-0ubuntu6 (For technical support please see http://www.ubuntu.com/support)
[ 18.576] Current version of pixman: 0.26.0
[ 18.576] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 18.576] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 18.577] (==) Log file: "/var/log/Xorg.0.log", Time: Fri Nov 16 19:19:07 2012
[ 18.589] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[ 18.600] (==) No Layout section. Using the first Screen section.
[ 18.601] (==) No screen section available. Using defaults.
[ 18.601] (**) |-->Screen "Default Screen Section" (0)
[ 18.601] (**) | |-->Monitor "<default monitor>"
[ 18.602] (==) No device specified for screen "Default Screen Section".
Using the first device section listed.
[ 18.602] (**) | |-->Device "gma500_gfx"
[ 18.602] (==) No monitor specified for screen "Default Screen Section".
Using a default monitor configuration.
[ 18.602] (==) Automatically adding devices
[ 18.602] (==) Automatically enabling devices
[ 18.602] (==) Automatically adding GPU devices
[ 18.616] (WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist.
[ 18.616] Entry deleted from font path.
[ 18.616] (WW) The directory "/usr/share/fonts/X11/100dpi/" does not exist.
[ 18.616] Entry deleted from font path.
[ 18.616] (WW) The directory "/usr/share/fonts/X11/75dpi/" does not exist.
[ 18.616] Entry deleted from font path.
[ 18.618] (WW) The directory "/usr/share/fonts/X11/100dpi" does not exist.
[ 18.618] Entry deleted from font path.
[ 18.618] (WW) The directory "/usr/share/fonts/X11/75dpi" does not exist.
[ 18.618] Entry deleted from font path.
[ 18.618] (WW) The directory "/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType" does not exist.
[ 18.618] Entry deleted from font path.
[ 18.619] (==) FontPath set to:
/usr/share/fonts/X11/misc,
/usr/share/fonts/X11/Type1,
built-ins
[ 18.619] (==) ModulePath set to "/usr/lib/i386-linux-gnu/xorg/extra-modules,/usr/lib/xorg/extra-modules,/usr/lib/xorg/modules"
[ 18.619] (II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
[ 18.619] (II) Loader magic: 0xb772f640
[ 18.619] (II) Module ABI versions:
[ 18.619] X.Org ANSI C Emulation: 0.4
[ 18.619] X.Org Video Driver: 13.0
[ 18.619] X.Org XInput driver : 18.0
[ 18.619] X.Org Server Extension : 7.0
[ 18.620] (II) config/udev: Adding drm device (/dev/dri/card0)
[ 18.624] (--) PCI:*(0:0:2:0) 8086:8108:1025:0244 rev 7, Mem @ 0xb0080000/524288, 0xc0000000/268435456, 0xb0000000/262144, I/O @ 0x00001800/8
[ 18.624] (II) Open ACPI successful (/var/run/acpid.socket)
[ 18.624] Initializing built-in extension Generic Event Extension
[ 18.624] Initializing built-in extension SHAPE
[ 18.624] Initializing built-in extension MIT-SHM
[ 18.624] Initializing built-in extension XInputExtension
[ 18.625] Initializing built-in extension XTEST
[ 18.625] Initializing built-in extension BIG-REQUESTS
[ 18.625] Initializing built-in extension SYNC
[ 18.625] Initializing built-in extension XKEYBOARD
[ 18.625] Initializing built-in extension XC-MISC
[ 18.625] Initializing built-in extension SECURITY
[ 18.625] Initializing built-in extension XINERAMA
[ 18.625] Initializing built-in extension XFIXES
[ 18.625] Initializing built-in extension RENDER
[ 18.625] Initializing built-in extension RANDR
[ 18.625] Initializing built-in extension COMPOSITE
[ 18.625] Initializing built-in extension DAMAGE
[ 18.625] Initializing built-in extension MIT-SCREEN-SAVER
[ 18.625] Initializing built-in extension DOUBLE-BUFFER
[ 18.626] Initializing built-in extension RECORD
[ 18.626] Initializing built-in extension DPMS
[ 18.626] Initializing built-in extension X-Resource
[ 18.626] Initializing built-in extension XVideo
[ 18.626] Initializing built-in extension XVideo-MotionCompensation
[ 18.626] Initializing built-in extension XFree86-VidModeExtension
[ 18.626] Initializing built-in extension XFree86-DGA
[ 18.626] Initializing built-in extension XFree86-DRI
[ 18.626] Initializing built-in extension DRI2
[ 18.626] (II) LoadModule: "glx"
[ 18.670] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 18.671] (II) Module glx: vendor="X.Org Foundation"
[ 18.671] compiled for 1.13.0, module version = 1.0.0
[ 18.671] ABI class: X.Org Server Extension, version 7.0
[ 18.672] (==) AIGLX enabled
[ 18.672] Loading extension GLX
[ 18.672] (II) LoadModule: "modesetting"
[ 18.673] (II) Loading /usr/lib/xorg/modules/drivers/modesetting_drv.so
[ 18.673] (II) Module modesetting: vendor="X.Org Foundation"
[ 18.673] compiled for 1.13.0, module version = 0.5.0
[ 18.673] Module class: X.Org Video Driver
[ 18.673] ABI class: X.Org Video Driver, version 13.0
[ 18.673] (II) modesetting: Driver for Modesetting Kernel Drivers: kms
[ 18.673] (++) using VT number 7
[ 18.674] (II) modesetting(0): using drv /dev/dri/card0
[ 18.674] (II) modesetting(0): Creating default Display subsection in Screen section
"Default Screen Section" for depth/fbbpp 24/32
[ 18.674] (==) modesetting(0): Depth 24, (==) framebuffer bpp 32
[ 18.674] (**) modesetting(0): Option "SWcursor" "ON"
[ 18.674] (==) modesetting(0): RGB weight 888
[ 18.674] (==) modesetting(0): Default visual is TrueColor
[ 18.674] (II) modesetting(0): ShadowFB: preferred NO, enabled NO
[ 18.945] (II) modesetting(0): Output LVDS-0 has no monitor section
[ 19.036] (II) modesetting(0): Output S-video-0 has no monitor section
[ 19.126] (II) modesetting(0): Output S-video-1 has no monitor section
[ 19.312] (II) modesetting(0): Output VGA-0 has no monitor section
[ 19.573] (II) modesetting(0): EDID for output LVDS-0
[ 19.573] (II) modesetting(0): Manufacturer: CMO Model: 1100 Serial#: 0
[ 19.573] (II) modesetting(0): Year: 2009 Week: 9
[ 19.573] (II) modesetting(0): EDID Version: 1.3
[ 19.573] (II) modesetting(0): Digital Display Input
[ 19.573] (II) modesetting(0): Max Image Size [cm]: horiz.: 25 vert.: 14
[ 19.573] (II) modesetting(0): Gamma: 2.20
[ 19.573] (II) modesetting(0): No DPMS capabilities specified
[ 19.573] (II) modesetting(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4
[ 19.573] (II) modesetting(0): First detailed timing is preferred mode
[ 19.573] (II) modesetting(0): redX: 0.565 redY: 0.348 greenX: 0.343 greenY: 0.585
[ 19.574] (II) modesetting(0): blueX: 0.161 blueY: 0.121 whiteX: 0.313 whiteY: 0.329
[ 19.574] (II) modesetting(0): Manufacturer's mask: 0
[ 19.574] (II) modesetting(0): Supported detailed timing:
[ 19.574] (II) modesetting(0): clock: 69.3 MHz Image Size: 256 x 144 mm
[ 19.574] (II) modesetting(0): h_active: 1366 h_sync: 1398 h_sync_end 1420 h_blank_end 1474 h_border: 0
[ 19.574] (II) modesetting(0): v_active: 768 v_sync: 770 v_sync_end 774 v_blanking: 784 v_border: 0
[ 19.574] (II) modesetting(0): N116B6-L02
[ 19.574] (II) modesetting(0): CMO
[ 19.574] (II) modesetting(0): N116B6-L02
[ 19.574] (II) modesetting(0): EDID (in hex):
[ 19.574] (II) modesetting(0): 00ffffffffffff000daf001100000000
[ 19.574] (II) modesetting(0): 0913010380190e780acf459059579529
[ 19.574] (II) modesetting(0): 1f505400000001010101010101010101
[ 19.574] (II) modesetting(0): 010101010101121b566c500010302016
[ 19.574] (II) modesetting(0): 2400009010000018000000fe004e3131
[ 19.575] (II) modesetting(0): 3642362d4c30320a2020000000fe0043
[ 19.575] (II) modesetting(0): 4d4f0a202020202020202020000000fe
[ 19.575] (II) modesetting(0): 004e31313642362d4c30320a20200071
[ 19.575] (II) modesetting(0): Printing probed modes for output LVDS-0
[ 19.575] (II) modesetting(0): Modeline "1366x768"x60.0 69.30 1366 1398 1420 1474 768 770 774 784 -hsync -vsync (47.0 kHz eP)
[ 19.665] (II) modesetting(0): EDID for output S-video-0
[ 19.758] (II) modesetting(0): EDID for output S-video-1
[ 19.943] (II) modesetting(0): EDID for output VGA-0
[ 19.943] (II) modesetting(0): Manufacturer: AOC Model: 2243 Serial#: 10322
[ 19.943] (II) modesetting(0): Year: 2012 Week: 5
[ 19.943] (II) modesetting(0): EDID Version: 1.3
[ 19.943] (II) modesetting(0): Analog Display Input, Input Voltage Level: 0.700/0.700 V
[ 19.943] (II) modesetting(0): Sync: Separate
[ 19.943] (II) modesetting(0): Max Image Size [cm]: horiz.: 48 vert.: 27
[ 19.943] (II) modesetting(0): Gamma: 2.20
[ 19.944] (II) modesetting(0): DPMS capabilities: Off; RGB/Color Display
[ 19.944] (II) modesetting(0): First detailed timing is preferred mode
[ 19.944] (II) modesetting(0): redX: 0.648 redY: 0.339 greenX: 0.282 greenY: 0.603
[ 19.944] (II) modesetting(0): blueX: 0.143 blueY: 0.070 whiteX: 0.313 whiteY: 0.329
[ 19.944] (II) modesetting(0): Supported established timings:
[ 19.944] (II) modesetting(0): 720x400@70Hz
[ 19.944] (II) modesetting(0): 640x480@60Hz
[ 19.944] (II) modesetting(0): 640x480@67Hz
[ 19.944] (II) modesetting(0): 640x480@72Hz
[ 19.944] (II) modesetting(0): 640x480@75Hz
[ 19.944] (II) modesetting(0): 800x600@56Hz
[ 19.944] (II) modesetting(0): 800x600@60Hz
[ 19.944] (II) modesetting(0): 800x600@72Hz
[ 19.944] (II) modesetting(0): 800x600@75Hz
[ 19.944] (II) modesetting(0): 832x624@75Hz
[ 19.944] (II) modesetting(0): 1024x768@60Hz
[ 19.944] (II) modesetting(0): 1024x768@70Hz
[ 19.944] (II) modesetting(0): 1024x768@75Hz
[ 19.944] (II) modesetting(0): 1280x1024@75Hz
[ 19.944] (II) modesetting(0): Manufacturer's mask: 0
[ 19.944] (II) modesetting(0): Supported standard timings:
[ 19.944] (II) modesetting(0): #0: hsize: 1280 vsize 960 refresh: 60 vid: 16513
[ 19.945] (II) modesetting(0): #1: hsize: 1280 vsize 1024 refresh: 60 vid: 32897
[ 19.945] (II) modesetting(0): #2: hsize: 1440 vsize 900 refresh: 60 vid: 149
[ 19.945] (II) modesetting(0): #3: hsize: 1680 vsize 1050 refresh: 60 vid: 179
[ 19.945] (II) modesetting(0): #4: hsize: 1920 vsize 1080 refresh: 60 vid: 49361
[ 19.945] (II) modesetting(0): Supported detailed timing:
[ 19.945] (II) modesetting(0): clock: 148.5 MHz Image Size: 477 x 268 mm
[ 19.945] (II) modesetting(0): h_active: 1920 h_sync: 2008 h_sync_end 2052 h_blank_end 2200 h_border: 0
[ 19.945] (II) modesetting(0): v_active: 1080 v_sync: 1084 v_sync_end 1089 v_blanking: 1125 v_border: 0
[ 19.945] (II) modesetting(0): Ranges: V min: 55 V max: 75 Hz, H min: 30 H max: 83 kHz, PixClock max 175 MHz
[ 19.945] (II) modesetting(0): Monitor name: 2243W
[ 19.945] (II) modesetting(0): Serial No: ACYC1OA010322
[ 19.945] (II) modesetting(0): EDID (in hex):
[ 19.945] (II) modesetting(0): 00ffffffffffff0005e3432252280000
[ 19.945] (II) modesetting(0): 0516010368301b782a3585a656489a24
[ 19.945] (II) modesetting(0): 125054bfef00814081809500b300d1c0
[ 19.945] (II) modesetting(0): 010101010101023a801871382d40582c
[ 19.945] (II) modesetting(0): 4500dd0c1100001e000000fd00374b1e
[ 19.945] (II) modesetting(0): 5311000a202020202020000000fc0032
[ 19.945] (II) modesetting(0): 323433570a20202020202020000000ff
[ 19.945] (II) modesetting(0): 0041435943314f413031303332320064
[ 19.946] (II) modesetting(0): Printing probed modes for output VGA-0
[ 19.946] (II) modesetting(0): Modeline "1920x1080"x60.0 148.50 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync (67.5 kHz eP)
[ 19.946] (II) modesetting(0): Modeline "1680x1050"x60.0 146.25 1680 1784 1960 2240 1050 1053 1059 1089 -hsync +vsync (65.3 kHz e)
[ 19.946] (II) modesetting(0): Modeline "1680x945"x60.0 131.48 1680 1784 1960 2240 945 946 949 978 -hsync +vsync (58.7 kHz)
[ 19.946] (II) modesetting(0): Modeline "1400x1050"x74.9 156.00 1400 1504 1648 1896 1050 1053 1057 1099 -hsync +vsync (82.3 kHz e)
[ 19.946] (II) modesetting(0): Modeline "1400x1050"x60.0 121.75 1400 1488 1632 1864 1050 1053 1057 1089 -hsync +vsync (65.3 kHz e)
[ 19.946] (II) modesetting(0): Modeline "1600x900"x60.0 118.96 1600 1696 1864 2128 900 901 904 932 -hsync +vsync (55.9 kHz)
[ 19.946] (II) modesetting(0): Modeline "1280x1024"x75.0 135.00 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync (80.0 kHz e)
[ 19.946] (II) modesetting(0): Modeline "1280x1024"x60.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz e)
[ 19.946] (II) modesetting(0): Modeline "1440x900"x75.0 136.75 1440 1536 1688 1936 900 903 909 942 -hsync +vsync (70.6 kHz e)
[ 19.946] (II) modesetting(0): Modeline "1440x900"x59.9 106.50 1440 1520 1672 1904 900 903 909 934 -hsync +vsync (55.9 kHz e)
[ 19.946] (II) modesetting(0): Modeline "1280x960"x60.0 108.00 1280 1376 1488 1800 960 961 964 1000 +hsync +vsync (60.0 kHz e)
[ 19.946] (II) modesetting(0): Modeline "1366x768"x60.0 85.89 1366 1439 1583 1800 768 769 772 795 -hsync +vsync (47.7 kHz)
[ 19.946] (II) modesetting(0): Modeline "1360x768"x60.0 85.50 1360 1424 1536 1792 768 771 777 795 +hsync +vsync (47.7 kHz e)
[ 19.946] (II) modesetting(0): Modeline "1280x800"x74.9 106.50 1280 1360 1488 1696 800 803 809 838 -hsync +vsync (62.8 kHz e)
[ 19.947] (II) modesetting(0): Modeline "1280x800"x59.8 83.50 1280 1352 1480 1680 800 803 809 831 +hsync -vsync (49.7 kHz e)
[ 19.947] (II) modesetting(0): Modeline "1152x864"x75.0 108.00 1152 1216 1344 1600 864 865 868 900 +hsync +vsync (67.5 kHz e)
[ 19.947] (II) modesetting(0): Modeline "1280x768"x74.9 102.25 1280 1360 1488 1696 768 771 778 805 +hsync -vsync (60.3 kHz e)
[ 19.947] (II) modesetting(0): Modeline "1280x768"x59.9 79.50 1280 1344 1472 1664 768 771 778 798 -hsync +vsync (47.8 kHz e)
[ 19.947] (II) modesetting(0): Modeline "1024x768"x75.1 78.80 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.1 kHz e)
[ 19.947] (II) modesetting(0): Modeline "1024x768"x70.1 75.00 1024 1048 1184 1328 768 771 777 806 -hsync -vsync (56.5 kHz e)
[ 19.947] (II) modesetting(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e)
[ 19.947] (II) modesetting(0): Modeline "1024x576"x60.0 46.97 1024 1064 1168 1312 576 577 580 597 -hsync +vsync (35.8 kHz)
[ 19.947] (II) modesetting(0): Modeline "832x624"x74.6 57.28 832 864 928 1152 624 625 628 667 -hsync -vsync (49.7 kHz e)
[ 19.947] (II) modesetting(0): Modeline "800x600"x72.2 50.00 800 856 976 1040 600 637 643 666 +hsync +vsync (48.1 kHz e)
[ 19.947] (II) modesetting(0): Modeline "800x600"x75.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz e)
[ 19.947] (II) modesetting(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e)
[ 19.947] (II) modesetting(0): Modeline "800x600"x56.2 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz e)
[ 19.947] (II) modesetting(0): Modeline "848x480"x60.0 33.75 848 864 976 1088 480 486 494 517 +hsync +vsync (31.0 kHz e)
[ 19.947] (II) modesetting(0): Modeline "640x480"x72.8 31.50 640 664 704 832 480 489 491 520 -hsync -vsync (37.9 kHz e)
[ 19.947] (II) modesetting(0): Modeline "640x480"x75.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz e)
[ 19.948] (II) modesetting(0): Modeline "640x480"x66.7 30.24 640 704 768 864 480 483 486 525 -hsync -vsync (35.0 kHz e)
[ 19.948] (II) modesetting(0): Modeline "640x480"x60.0 25.20 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz e)
[ 19.948] (II) modesetting(0): Modeline "720x400"x70.1 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz e)
[ 19.948] (II) modesetting(0): Output LVDS-0 connected
[ 19.948] (II) modesetting(0): Output S-video-0 disconnected
[ 19.948] (II) modesetting(0): Output S-video-1 disconnected
[ 19.948] (II) modesetting(0): Output VGA-0 connected
[ 19.948] (II) modesetting(0): Using exact sizes for initial modes
[ 19.948] (II) modesetting(0): Output LVDS-0 using initial mode 1366x768
[ 19.948] (II) modesetting(0): Output VGA-0 using initial mode 1366x768
[ 19.948] (II) modesetting(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated.
[ 19.948] (==) modesetting(0): DPI set to (96, 96)
[ 19.948] (II) Loading sub module "fb"
[ 19.948] (II) LoadModule: "fb"
[ 19.949] (II) Loading /usr/lib/xorg/modules/libfb.so
[ 19.950] (II) Module fb: vendor="X.Org Foundation"
[ 19.950] compiled for 1.13.0, module version = 1.0.0
[ 19.950] ABI class: X.Org ANSI C Emulation, version 0.4
[ 19.950] (==) Depth 24 pixmap format is 32 bpp
[ 19.950] (==) modesetting(0): Backing store disabled
[ 19.950] (==) modesetting(0): Silken mouse enabled
[ 19.950] (II) modesetting(0): RandR 1.2 enabled, ignore the following RandR disabled message.
[ 19.951] (==) modesetting(0): DPMS enabled
[ 20.321] (--) RandR disabled
[ 20.412] (II) AIGLX: Screen 0 is not DRI2 capable
[ 20.412] (II) AIGLX: Screen 0 is not DRI capable
[ 21.073] (II) AIGLX: Loaded and initialized swrast
[ 21.073] (II) GLX: Initialized DRISWRAST GL provider for screen 0
[ 21.075] (II) modesetting(0): Damage tracking initialized
[ 21.075] (II) modesetting(0): Setting screen physical size to 361 x 203
[ 21.242] (II) XKB: reuse xkmfile /var/lib/xkb/server-B20D7FC79C7F597315E3E501AEF10E0D866E8E92.xkm
[ 21.261] (II) config/udev: Adding input device Video Bus (/dev/input/event6)
[ 21.261] (**) Video Bus: Applying InputClass "evdev keyboard catchall"
[ 21.261] (II) LoadModule: "evdev"
[ 21.272] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 21.288] (II) Module evdev: vendor="X.Org Foundation"
[ 21.288] compiled for 1.13.0, module version = 2.7.3
[ 21.288] Module class: X.Org XInput Driver
[ 21.288] ABI class: X.Org XInput driver, version 18.0
[ 21.288] (II) Using input driver 'evdev' for 'Video Bus'
[ 21.289] (**) Video Bus: always reports core events
[ 21.289] (**) evdev: Video Bus: Device: "/dev/input/event6"
[ 21.289] (--) evdev: Video Bus: Vendor 0 Product 0x6
[ 21.289] (--) evdev: Video Bus: Found keys
[ 21.289] (II) evdev: Video Bus: Configuring as keyboard
[ 21.289] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input7/event6"
[ 21.289] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 6)
[ 21.290] (**) Option "xkb_rules" "evdev"
[ 21.290] (**) Option "xkb_model" "pc105"
[ 21.290] (**) Option "xkb_layout" "us"
[ 21.292] (II) config/udev: Adding input device Power Button (/dev/input/event1)
[ 21.292] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 21.292] (II) Using input driver 'evdev' for 'Power Button'
[ 21.292] (**) Power Button: always reports core events
[ 21.292] (**) evdev: Power Button: Device: "/dev/input/event1"
[ 21.293] (--) evdev: Power Button: Vendor 0 Product 0x1
[ 21.293] (--) evdev: Power Button: Found keys
[ 21.293] (II) evdev: Power Button: Configuring as keyboard
[ 21.293] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1/event1"
[ 21.293] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 7)
[ 21.293] (**) Option "xkb_rules" "evdev"
[ 21.293] (**) Option "xkb_model" "pc105"
[ 21.293] (**) Option "xkb_layout" "us"
[ 21.295] (II) config/udev: Adding input device Lid Switch (/dev/input/event0)
[ 21.295] (II) No input driver specified, ignoring this device.
[ 21.295] (II) This device may have been added with another device file.
[ 21.296] (II) config/udev: Adding input device Sleep Button (/dev/input/event2)
[ 21.296] (**) Sleep Button: Applying InputClass "evdev keyboard catchall"
[ 21.297] (II) Using input driver 'evdev' for 'Sleep Button'
[ 21.297] (**) Sleep Button: always reports core events
[ 21.297] (**) evdev: Sleep Button: Device: "/dev/input/event2"
[ 21.297] (--) evdev: Sleep Button: Vendor 0 Product 0x3
[ 21.297] (--) evdev: Sleep Button: Found keys
[ 21.297] (II) evdev: Sleep Button: Configuring as keyboard
[ 21.297] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input2/event2"
[ 21.297] (II) XINPUT: Adding extended input device "Sleep Button" (type: KEYBOARD, id 8)
[ 21.297] (**) Option "xkb_rules" "evdev"
[ 21.297] (**) Option "xkb_model" "pc105"
[ 21.297] (**) Option "xkb_layout" "us"
[ 21.299] (II) config/udev: Adding drm device (/dev/dri/card0)
[ 21.301] (II) config/udev: Adding input device HDA Intel MID Mic (/dev/input/event10)
[ 21.301] (II) No input driver specified, ignoring this device.
[ 21.301] (II) This device may have been added with another device file.
[ 21.302] (II) config/udev: Adding input device HDA Intel MID Headphone (/dev/input/event11)
[ 21.302] (II) No input driver specified, ignoring this device.
[ 21.302] (II) This device may have been added with another device file.
[ 21.303] (II) config/udev: Adding input device Microsft Microsoft Wireless Desktop Receiver 3.1 (/dev/input/event4)
[ 21.303] (**) Microsft Microsoft Wireless Desktop Receiver 3.1: Applying InputClass "evdev keyboard catchall"
[ 21.304] (II) Using input driver 'evdev' for 'Microsft Microsoft Wireless Desktop Receiver 3.1'
[ 21.304] (**) Microsft Microsoft Wireless Desktop Receiver 3.1: always reports core events
[ 21.304] (**) evdev: Microsft Microsoft Wireless Desktop Receiver 3.1: Device: "/dev/input/event4"
[ 21.304] (--) evdev: Microsft Microsoft Wireless Desktop Receiver 3.1: Vendor 0x45e Product 0xf9
[ 21.304] (--) evdev: Microsft Microsoft Wireless Desktop Receiver 3.1: Found keys
[ 21.304] (II) evdev: Microsft Microsoft Wireless Desktop Receiver 3.1: Configuring as keyboard
[ 21.304] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.0/input/input5/event4"
[ 21.304] (II) XINPUT: Adding extended input device "Microsft Microsoft Wireless Desktop Receiver 3.1" (type: KEYBOARD, id 9)
[ 21.304] (**) Option "xkb_rules" "evdev"
[ 21.304] (**) Option "xkb_model" "pc105"
[ 21.304] (**) Option "xkb_layout" "us"
[ 21.307] (II) config/udev: Adding input device Microsft Microsoft Wireless Desktop Receiver 3.1 (/dev/input/event5)
[ 21.307] (**) Microsft Microsoft Wireless Desktop Receiver 3.1: Applying InputClass "evdev pointer catchall"
[ 21.307] (**) Microsft Microsoft Wireless Desktop Receiver 3.1: Applying InputClass "evdev keyboard catchall"
[ 21.307] (II) Using input driver 'evdev' for 'Microsft Microsoft Wireless Desktop Receiver 3.1'
[ 21.307] (**) Microsft Microsoft Wireless Desktop Receiver 3.1: always reports core events
[ 21.307] (**) evdev: Microsft Microsoft Wireless Desktop Receiver 3.1: Device: "/dev/input/event5"
[ 21.307] (--) evdev: Microsft Microsoft Wireless Desktop Receiver 3.1: Vendor 0x45e Product 0xf9
[ 21.307] (--) evdev: Microsft Microsoft Wireless Desktop Receiver 3.1: Found 9 mouse buttons
[ 21.307] (--) evdev: Microsft Microsoft Wireless Desktop Receiver 3.1: Found scroll wheel(s)
[ 21.308] (--) evdev: Microsft Microsoft Wireless Desktop Receiver 3.1: Found relative axes
[ 21.308] (--) evdev: Microsft Microsoft Wireless Desktop Receiver 3.1: Found x and y relative axes
[ 21.308] (--) evdev: Microsft Microsoft Wireless Desktop Receiver 3.1: Found absolute axes
[ 21.308] (II) evdev: Microsft Microsoft Wireless Desktop Receiver 3.1: Forcing absolute x/y axes to exist.
[ 21.308] (--) evdev: Microsft Microsoft Wireless Desktop Receiver 3.1: Found keys
[ 21.308] (II) evdev: Microsft Microsoft Wireless Desktop Receiver 3.1: Configuring as mouse
[ 21.308] (II) evdev: Microsft Microsoft Wireless Desktop Receiver 3.1: Configuring as keyboard
[ 21.308] (II) evdev: Microsft Microsoft Wireless Desktop Receiver 3.1: Adding scrollwheel support
[ 21.308] (**) evdev: Microsft Microsoft Wireless Desktop Receiver 3.1: YAxisMapping: buttons 4 and 5
[ 21.308] (**) evdev: Microsft Microsoft Wireless Desktop Receiver 3.1: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 21.308] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.1/input/input6/event5"
[ 21.308] (II) XINPUT: Adding extended input device "Microsft Microsoft Wireless Desktop Receiver 3.1" (type: KEYBOARD, id 10)
[ 21.308] (**) Option "xkb_rules" "evdev"
[ 21.308] (**) Option "xkb_model" "pc105"
[ 21.308] (**) Option "xkb_layout" "us"
[ 21.309] (II) evdev: Microsft Microsoft Wireless Desktop Receiver 3.1: initialized for relative axes.
[ 21.309] (WW) evdev: Microsft Microsoft Wireless Desktop Receiver 3.1: ignoring absolute axes.
[ 21.310] (**) Microsft Microsoft Wireless Desktop Receiver 3.1: (accel) keeping acceleration scheme 1
[ 21.310] (**) Microsft Microsoft Wireless Desktop Receiver 3.1: (accel) acceleration profile 0
[ 21.310] (**) Microsft Microsoft Wireless Desktop Receiver 3.1: (accel) acceleration factor: 2.000
[ 21.310] (**) Microsft Microsoft Wireless Desktop Receiver 3.1: (accel) acceleration threshold: 4
[ 21.311] (II) config/udev: Adding input device Microsft Microsoft Wireless Desktop Receiver 3.1 (/dev/input/mouse0)
[ 21.311] (II) No input driver specified, ignoring this device.
[ 21.312] (II) This device may have been added with another device file.
[ 21.313] (II) config/udev: Adding input device WebCam (/dev/input/event8)
[ 21.313] (**) WebCam: Applying InputClass "evdev keyboard catchall"
[ 21.313] (II) Using input driver 'evdev' for 'WebCam'
[ 21.313] (**) WebCam: always reports core events
[ 21.313] (**) evdev: WebCam: Device: "/dev/input/event8"
[ 21.313] (--) evdev: WebCam: Vendor 0x64e Product 0xa102
[ 21.313] (--) evdev: WebCam: Found keys
[ 21.313] (II) evdev: WebCam: Configuring as keyboard
[ 21.314] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.7/usb1/1-4/1-4:1.0/input/input9/event8"
[ 21.314] (II) XINPUT: Adding extended input device "WebCam" (type: KEYBOARD, id 11)
[ 21.314] (**) Option "xkb_rules" "evdev"
[ 21.314] (**) Option "xkb_model" "pc105"
[ 21.314] (**) Option "xkb_layout" "us"
[ 21.316] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event3)
[ 21.316] (**) AT Translated Set 2 keyboard: Applying InputClass "evdev keyboard catchall"
[ 21.316] (II) Using input driver 'evdev' for 'AT Translated Set 2 keyboard'
[ 21.317] (**) AT Translated Set 2 keyboard: always reports core events
[ 21.317] (**) evdev: AT Translated Set 2 keyboard: Device: "/dev/input/event3"
[ 21.317] (--) evdev: AT Translated Set 2 keyboard: Vendor 0x1 Product 0x1
[ 21.317] (--) evdev: AT Translated Set 2 keyboard: Found keys
[ 21.317] (II) evdev: AT Translated Set 2 keyboard: Configuring as keyboard
[ 21.317] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio0/input/input4/event3"
[ 21.317] (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD, id 12)
[ 21.317] (**) Option "xkb_rules" "evdev"
[ 21.317] (**) Option "xkb_model" "pc105"
[ 21.317] (**) Option "xkb_layout" "us"
[ 21.320] (II) config/udev: Adding input device SynPS/2 Synaptics TouchPad (/dev/input/event7)
[ 21.320] (**) SynPS/2 Synaptics TouchPad: Applying InputClass "evdev touchpad catchall"
[ 21.320] (**) SynPS/2 Synaptics TouchPad: Applying InputClass "touchpad catchall"
[ 21.320] (**) SynPS/2 Synaptics TouchPad: Applying InputClass "Default clickpad buttons"
[ 21.320] (II) LoadModule: "synaptics"
[ 21.321] (II) Loading /usr/lib/xorg/modules/input/synaptics_drv.so
[ 21.336] (II) Module synaptics: vendor="X.Org Foundation"
[ 21.337] compiled for 1.12.99.905, module version = 1.6.2
[ 21.337] Module class: X.Org XInput Driver
[ 21.337] ABI class: X.Org XInput driver, version 18.0
[ 21.337] (II) Using input driver 'synaptics' for 'SynPS/2 Synaptics TouchPad'
[ 21.337] (**) SynPS/2 Synaptics TouchPad: always reports core events
[ 21.337] (**) Option "Device" "/dev/input/event7"
[ 21.338] (II) synaptics: SynPS/2 Synaptics TouchPad: ignoring touch events for semi-multitouch device
[ 21.338] (--) synaptics: SynPS/2 Synaptics TouchPad: x-axis range 1472 - 5888
[ 21.338] (--) synaptics: SynPS/2 Synaptics TouchPad: y-axis range 1408 - 5012
[ 21.338] (--) synaptics: SynPS/2 Synaptics TouchPad: pressure range 0 - 255
[ 21.338] (--) synaptics: SynPS/2 Synaptics TouchPad: finger width range 0 - 15
[ 21.338] (--) synaptics: SynPS/2 Synaptics TouchPad: buttons: left right double triple
[ 21.338] (--) synaptics: SynPS/2 Synaptics TouchPad: Vendor 0x2 Product 0x7
[ 21.338] (--) synaptics: SynPS/2 Synaptics TouchPad: touchpad found
[ 21.338] (**) SynPS/2 Synaptics TouchPad: always reports core events
[ 21.339] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio2/input/input8/event7"
[ 21.339] (II) XINPUT: Adding extended input device "SynPS/2 Synaptics TouchPad" (type: TOUCHPAD, id 13)
[ 21.339] (**) synaptics: SynPS/2 Synaptics TouchPad: (accel) MinSpeed is now constant deceleration 2.5
[ 21.339] (**) synaptics: SynPS/2 Synaptics TouchPad: MaxSpeed is now 1.75
[ 21.339] (**) synaptics: SynPS/2 Synaptics TouchPad: AccelFactor is now 0.035
[ 21.340] (**) SynPS/2 Synaptics TouchPad: (accel) keeping acceleration scheme 1
[ 21.340] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration profile 1
[ 21.340] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration factor: 2.000
[ 21.340] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration threshold: 4
[ 21.340] (--) synaptics: SynPS/2 Synaptics TouchPad: touchpad found
[ 21.341] (II) config/udev: Adding input device SynPS/2 Synaptics TouchPad (/dev/input/mouse1)
[ 21.341] (**) SynPS/2 Synaptics TouchPad: Ignoring device from InputClass "touchpad ignore duplicates"
[ 21.350] (II) config/udev: Adding input device Acer BMA150 accelerometer (/dev/input/event9)
[ 21.351] (II) No input driver specified, ignoring this device.
[ 21.351] (II) This device may have been added with another device file.
[ 21.351] (II) config/udev: Adding input device Acer BMA150 accelerometer (/dev/input/js0)
[ 21.351] (II) No input driver specified, ignoring this device.
[ 21.352] (II) This device may have been added with another device file.
[ 52.087] (II) modesetting(0): EDID vendor "CMO", prod id 4352
[ 52.087] (II) modesetting(0): Printing DDC gathered Modelines:
[ 52.087] (II) modesetting(0): Modeline "1366x768"x0.0 69.30 1366 1398 1420 1474 768 770 774 784 -hsync -vsync (47.0 kHz eP)
[ 52.942] (II) modesetting(0): EDID vendor "CMO", prod id 4352
[ 52.942] (II) modesetting(0): Printing DDC gathered Modelines:
[ 52.942] (II) modesetting(0): Modeline "1366x768"x0.0 69.30 1366 1398 1420 1474 768 770 774 784 -hsync -vsync (47.0 kHz eP)
[ 53.573] (II) modesetting(0): EDID vendor "CMO", prod id 4352
[ 53.573] (II) modesetting(0): Printing DDC gathered Modelines:
[ 53.573] (II) modesetting(0): Modeline "1366x768"x0.0 69.30 1366 1398 1420 1474 768 770 774 784 -hsync -vsync (47.0 kHz eP)
[ 53.945] (II) modesetting(0): Allocate new frame buffer 1920x1080 stride
[ 96.598] (II) modesetting(0): EDID vendor "CMO", prod id 4352
[ 96.599] (II) modesetting(0): Printing DDC gathered Modelines:
[ 96.606] (II) modesetting(0): Modeline "1366x768"x0.0 69.30 1366 1398 1420 1474 768 770 774 784 -hsync -vsync (47.0 kHz eP)
[ 102.563] (II) modesetting(0): EDID vendor "CMO", prod id 4352
[ 102.564] (II) modesetting(0): Printing DDC gathered Modelines:
[ 102.564] (II) modesetting(0): Modeline "1366x768"x0.0 69.30 1366 1398 1420 1474 768 770 774 784 -hsync -vsync (47.0 kHz eP)
[ 103.464] (II) modesetting(0): EDID vendor "CMO", prod id 4352
[ 103.464] (II) modesetting(0): Printing DDC gathered Modelines:
[ 103.464] (II) modesetting(0): Modeline "1366x768"x0.0 69.30 1366 1398 1420 1474 768 770 774 784 -hsync -vsync (47.0 kHz eP)
[ 104.184] (II) modesetting(0): EDID vendor "CMO", prod id 4352
[ 104.184] (II) modesetting(0): Printing DDC gathered Modelines:
[ 104.184] (II) modesetting(0): Modeline "1366x768"x0.0 69.30 1366 1398 1420 1474 768 770 774 784 -hsync -vsync (47.0 kHz eP)
[ 105.662] (II) modesetting(0): EDID vendor "CMO", prod id 4352
[ 105.663] (II) modesetting(0): Printing DDC gathered Modelines:
[ 105.663] (II) modesetting(0): Modeline "1366x768"x0.0 69.30 1366 1398 1420 1474 768 770 774 784 -hsync -vsync (47.0 kHz eP)
[ 106.305] (II) modesetting(0): EDID vendor "CMO", prod id 4352
[ 106.305] (II) modesetting(0): Printing DDC gathered Modelines:
[ 106.305] (II) modesetting(0): Modeline "1366x768"x0.0 69.30 1366 1398 1420 1474 768 770 774 784 -hsync -vsync (47.0 kHz eP)
[ 1496.536] (II) modesetting(0): EDID vendor "CMO", prod id 4352
[ 1496.536] (II) modesetting(0): Printing DDC gathered Modelines:
[ 1496.537] (II) modesetting(0): Modeline "1366x768"x0.0 69.30 1366 1398 1420 1474 768 770 774 784 -hsync -vsync (47.0 kHz eP)
Re: 12.10 - Extended Desktop - How to change virtual desktop size?
AFAIK you are using s/w rasteriser/render & no DRI support.
The video driver looks to be some default Xorg driver..
The gma500_gfx is the *buntu supported open source attempt..
I think you are not using it..
http://ubuntuforums.org/showthread.p...984236&page=13
post #107
"The EMGD or PSB drivers are unsupported in current Ubuntus"
I would backup/delete the /etc/X11/xorg.conf & reboot, then look at Xorg.0.conf to see if gma500 driver has claimed the video h/w..
If you like to take some risk, the xorg-edgers ppa could be an option, there is initial support for the new CedarView/Trail which is also based on PowerVR.
Re: 12.10 - Extended Desktop - How to change virtual desktop size?
Quote:
Originally Posted by
BicyclerBoy
AFAIK you are using s/w rasteriser/render & no DRI support.
The video driver looks to be some default Xorg driver..
The gma500_gfx is the *buntu supported open source attempt..
I think you are not using it..
http://ubuntuforums.org/showthread.p...984236&page=13
post #107
"The EMGD or PSB drivers are unsupported in current Ubuntus"
I would backup/delete the /etc/X11/xorg.conf & reboot, then look at Xorg.0.conf to see if gma500 driver has claimed the video h/w..
If you like to take some risk, the xorg-edgers ppa could be an option, there is initial support for the new CedarView/Trail which is also based on PowerVR.
The xorg.conf has been removed (bk'd), we'll reboot and see what we have ... thanks so much, we'll give it a shot.
If not, we'll try to add that ppa and go that route.
Re: 12.10 - Extended Desktop - How to change virtual desktop size?
https://wiki.ubuntu.com/HardwareSupp...eoCardsPoulsbo
The best advise there is to stay on 12.04..
One major component of xorg-edgers is a later kernel..
Re: 12.10 - Extended Desktop - How to change virtual desktop size?
Quote:
Originally Posted by
BicyclerBoy
Understood:
Here is the updated Xorg.0.log
Code:
[ 21.919]
X.Org X Server 1.13.0
Release Date: 2012-09-05
[ 21.920] X Protocol Version 11, Revision 0
[ 21.920] Build Operating System: Linux 3.2.0-26-generic i686 Ubuntu
[ 21.920] Current Operating System: Linux tsani-top 3.5.0-17-lowlatency #18-Ubuntu SMP PREEMPT Tue Oct 9 20:05:16 UTC 2012 i686
[ 21.920] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.5.0-17-lowlatency root=UUID=141b3433-b441-4d95-9362-eccd3aa91713 ro quiet splash vt.handoff=7
[ 21.920] Build Date: 08 October 2012 03:34:08PM
[ 21.920] xorg-server 2:1.13.0-0ubuntu6 (For technical support please see http://www.ubuntu.com/support)
[ 21.920] Current version of pixman: 0.26.0
[ 21.921] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 21.921] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 21.921] (==) Log file: "/var/log/Xorg.0.log", Time: Fri Nov 16 21:25:33 2012
[ 21.940] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[ 21.952] (==) No Layout section. Using the first Screen section.
[ 21.952] (==) No screen section available. Using defaults.
[ 21.952] (**) |-->Screen "Default Screen Section" (0)
[ 21.952] (**) | |-->Monitor "<default monitor>"
[ 21.953] (==) No device specified for screen "Default Screen Section".
Using the first device section listed.
[ 21.953] (**) | |-->Device "gma500_gfx"
[ 21.953] (==) No monitor specified for screen "Default Screen Section".
Using a default monitor configuration.
[ 21.953] (==) Automatically adding devices
[ 21.953] (==) Automatically enabling devices
[ 21.953] (==) Automatically adding GPU devices
[ 21.979] (WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist.
[ 21.979] Entry deleted from font path.
[ 21.979] (WW) The directory "/usr/share/fonts/X11/100dpi/" does not exist.
[ 21.979] Entry deleted from font path.
[ 21.979] (WW) The directory "/usr/share/fonts/X11/75dpi/" does not exist.
[ 21.979] Entry deleted from font path.
[ 21.980] (WW) The directory "/usr/share/fonts/X11/100dpi" does not exist.
[ 21.980] Entry deleted from font path.
[ 21.980] (WW) The directory "/usr/share/fonts/X11/75dpi" does not exist.
[ 21.980] Entry deleted from font path.
[ 21.980] (WW) The directory "/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType" does not exist.
[ 21.980] Entry deleted from font path.
[ 21.980] (==) FontPath set to:
/usr/share/fonts/X11/misc,
/usr/share/fonts/X11/Type1,
built-ins
[ 21.980] (==) ModulePath set to "/usr/lib/i386-linux-gnu/xorg/extra-modules,/usr/lib/xorg/extra-modules,/usr/lib/xorg/modules"
[ 21.980] (II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
[ 21.980] (II) Loader magic: 0xb7704640
[ 21.980] (II) Module ABI versions:
[ 21.980] X.Org ANSI C Emulation: 0.4
[ 21.980] X.Org Video Driver: 13.0
[ 21.980] X.Org XInput driver : 18.0
[ 21.980] X.Org Server Extension : 7.0
[ 21.982] (II) config/udev: Adding drm device (/dev/dri/card0)
[ 21.985] (--) PCI:*(0:0:2:0) 8086:8108:1025:0244 rev 7, Mem @ 0xb0080000/524288, 0xc0000000/268435456, 0xb0000000/262144, I/O @ 0x00001800/8
[ 21.985] (II) Open ACPI successful (/var/run/acpid.socket)
[ 21.986] Initializing built-in extension Generic Event Extension
[ 21.986] Initializing built-in extension SHAPE
[ 21.986] Initializing built-in extension MIT-SHM
[ 21.986] Initializing built-in extension XInputExtension
[ 21.986] Initializing built-in extension XTEST
[ 21.986] Initializing built-in extension BIG-REQUESTS
[ 21.986] Initializing built-in extension SYNC
[ 21.986] Initializing built-in extension XKEYBOARD
[ 21.986] Initializing built-in extension XC-MISC
[ 21.986] Initializing built-in extension SECURITY
[ 21.986] Initializing built-in extension XINERAMA
[ 21.986] Initializing built-in extension XFIXES
[ 21.986] Initializing built-in extension RENDER
[ 21.987] Initializing built-in extension RANDR
[ 21.987] Initializing built-in extension COMPOSITE
[ 21.987] Initializing built-in extension DAMAGE
[ 21.987] Initializing built-in extension MIT-SCREEN-SAVER
[ 21.987] Initializing built-in extension DOUBLE-BUFFER
[ 21.987] Initializing built-in extension RECORD
[ 21.987] Initializing built-in extension DPMS
[ 21.987] Initializing built-in extension X-Resource
[ 21.987] Initializing built-in extension XVideo
[ 21.987] Initializing built-in extension XVideo-MotionCompensation
[ 21.987] Initializing built-in extension XFree86-VidModeExtension
[ 21.987] Initializing built-in extension XFree86-DGA
[ 21.987] Initializing built-in extension XFree86-DRI
[ 21.987] Initializing built-in extension DRI2
[ 21.987] (II) LoadModule: "glx"
[ 22.033] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 22.034] (II) Module glx: vendor="X.Org Foundation"
[ 22.034] compiled for 1.13.0, module version = 1.0.0
[ 22.034] ABI class: X.Org Server Extension, version 7.0
[ 22.034] (==) AIGLX enabled
[ 22.034] Loading extension GLX
[ 22.034] (II) LoadModule: "modesetting"
[ 22.035] (II) Loading /usr/lib/xorg/modules/drivers/modesetting_drv.so
[ 22.036] (II) Module modesetting: vendor="X.Org Foundation"
[ 22.036] compiled for 1.13.0, module version = 0.5.0
[ 22.036] Module class: X.Org Video Driver
[ 22.036] ABI class: X.Org Video Driver, version 13.0
[ 22.036] (II) modesetting: Driver for Modesetting Kernel Drivers: kms
[ 22.036] (++) using VT number 7
[ 22.036] (II) modesetting(0): using drv /dev/dri/card0
[ 22.037] (II) modesetting(0): Creating default Display subsection in Screen section
"Default Screen Section" for depth/fbbpp 24/32
[ 22.037] (==) modesetting(0): Depth 24, (==) framebuffer bpp 32
[ 22.037] (**) modesetting(0): Option "SWcursor" "ON"
[ 22.037] (==) modesetting(0): RGB weight 888
[ 22.037] (==) modesetting(0): Default visual is TrueColor
[ 22.037] (II) modesetting(0): ShadowFB: preferred NO, enabled NO
[ 22.265] (II) modesetting(0): Output LVDS-0 has no monitor section
[ 22.356] (II) modesetting(0): Output S-video-0 has no monitor section
[ 22.446] (II) modesetting(0): Output S-video-1 has no monitor section
[ 22.630] (II) modesetting(0): Output VGA-0 has no monitor section
[ 22.860] (II) modesetting(0): EDID for output LVDS-0
[ 22.861] (II) modesetting(0): Manufacturer: CMO Model: 1100 Serial#: 0
[ 22.861] (II) modesetting(0): Year: 2009 Week: 9
[ 22.861] (II) modesetting(0): EDID Version: 1.3
[ 22.861] (II) modesetting(0): Digital Display Input
[ 22.861] (II) modesetting(0): Max Image Size [cm]: horiz.: 25 vert.: 14
[ 22.861] (II) modesetting(0): Gamma: 2.20
[ 22.861] (II) modesetting(0): No DPMS capabilities specified
[ 22.861] (II) modesetting(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4
[ 22.861] (II) modesetting(0): First detailed timing is preferred mode
[ 22.861] (II) modesetting(0): redX: 0.565 redY: 0.348 greenX: 0.343 greenY: 0.585
[ 22.861] (II) modesetting(0): blueX: 0.161 blueY: 0.121 whiteX: 0.313 whiteY: 0.329
[ 22.861] (II) modesetting(0): Manufacturer's mask: 0
[ 22.861] (II) modesetting(0): Supported detailed timing:
[ 22.861] (II) modesetting(0): clock: 69.3 MHz Image Size: 256 x 144 mm
[ 22.862] (II) modesetting(0): h_active: 1366 h_sync: 1398 h_sync_end 1420 h_blank_end 1474 h_border: 0
[ 22.862] (II) modesetting(0): v_active: 768 v_sync: 770 v_sync_end 774 v_blanking: 784 v_border: 0
[ 22.862] (II) modesetting(0): N116B6-L02
[ 22.862] (II) modesetting(0): CMO
[ 22.862] (II) modesetting(0): N116B6-L02
[ 22.862] (II) modesetting(0): EDID (in hex):
[ 22.862] (II) modesetting(0): 00ffffffffffff000daf001100000000
[ 22.862] (II) modesetting(0): 0913010380190e780acf459059579529
[ 22.862] (II) modesetting(0): 1f505400000001010101010101010101
[ 22.862] (II) modesetting(0): 010101010101121b566c500010302016
[ 22.862] (II) modesetting(0): 2400009010000018000000fe004e3131
[ 22.862] (II) modesetting(0): 3642362d4c30320a2020000000fe0043
[ 22.862] (II) modesetting(0): 4d4f0a202020202020202020000000fe
[ 22.862] (II) modesetting(0): 004e31313642362d4c30320a20200071
[ 22.862] (II) modesetting(0): Printing probed modes for output LVDS-0
[ 22.862] (II) modesetting(0): Modeline "1366x768"x60.0 69.30 1366 1398 1420 1474 768 770 774 784 -hsync -vsync (47.0 kHz eP)
[ 22.953] (II) modesetting(0): EDID for output S-video-0
[ 23.043] (II) modesetting(0): EDID for output S-video-1
[ 23.233] (II) modesetting(0): EDID for output VGA-0
[ 23.233] (II) modesetting(0): Manufacturer: AOC Model: 2243 Serial#: 10322
[ 23.233] (II) modesetting(0): Year: 2012 Week: 5
[ 23.233] (II) modesetting(0): EDID Version: 1.3
[ 23.233] (II) modesetting(0): Analog Display Input, Input Voltage Level: 0.700/0.700 V
[ 23.233] (II) modesetting(0): Sync: Separate
[ 23.234] (II) modesetting(0): Max Image Size [cm]: horiz.: 48 vert.: 27
[ 23.234] (II) modesetting(0): Gamma: 2.20
[ 23.234] (II) modesetting(0): DPMS capabilities: Off; RGB/Color Display
[ 23.244] (II) modesetting(0): First detailed timing is preferred mode
[ 23.244] (II) modesetting(0): redX: 0.648 redY: 0.339 greenX: 0.282 greenY: 0.603
[ 23.244] (II) modesetting(0): blueX: 0.143 blueY: 0.070 whiteX: 0.313 whiteY: 0.329
[ 23.244] (II) modesetting(0): Supported established timings:
[ 23.244] (II) modesetting(0): 720x400@70Hz
[ 23.244] (II) modesetting(0): 640x480@60Hz
[ 23.244] (II) modesetting(0): 640x480@67Hz
[ 23.244] (II) modesetting(0): 640x480@72Hz
[ 23.244] (II) modesetting(0): 640x480@75Hz
[ 23.244] (II) modesetting(0): 800x600@56Hz
[ 23.246] (II) modesetting(0): 800x600@60Hz
[ 23.246] (II) modesetting(0): 800x600@72Hz
[ 23.246] (II) modesetting(0): 800x600@75Hz
[ 23.246] (II) modesetting(0): 832x624@75Hz
[ 23.246] (II) modesetting(0): 1024x768@60Hz
[ 23.246] (II) modesetting(0): 1024x768@70Hz
[ 23.246] (II) modesetting(0): 1024x768@75Hz
[ 23.246] (II) modesetting(0): 1280x1024@75Hz
[ 23.246] (II) modesetting(0): Manufacturer's mask: 0
[ 23.246] (II) modesetting(0): Supported standard timings:
[ 23.246] (II) modesetting(0): #0: hsize: 1280 vsize 960 refresh: 60 vid: 16513
[ 23.246] (II) modesetting(0): #1: hsize: 1280 vsize 1024 refresh: 60 vid: 32897
[ 23.246] (II) modesetting(0): #2: hsize: 1440 vsize 900 refresh: 60 vid: 149
[ 23.246] (II) modesetting(0): #3: hsize: 1680 vsize 1050 refresh: 60 vid: 179
[ 23.246] (II) modesetting(0): #4: hsize: 1920 vsize 1080 refresh: 60 vid: 49361
[ 23.247] (II) modesetting(0): Supported detailed timing:
[ 23.247] (II) modesetting(0): clock: 148.5 MHz Image Size: 477 x 268 mm
[ 23.247] (II) modesetting(0): h_active: 1920 h_sync: 2008 h_sync_end 2052 h_blank_end 2200 h_border: 0
[ 23.247] (II) modesetting(0): v_active: 1080 v_sync: 1084 v_sync_end 1089 v_blanking: 1125 v_border: 0
[ 23.247] (II) modesetting(0): Ranges: V min: 55 V max: 75 Hz, H min: 30 H max: 83 kHz, PixClock max 175 MHz
[ 23.247] (II) modesetting(0): Monitor name: 2243W
[ 23.247] (II) modesetting(0): Serial No: ACYC1OA010322
[ 23.247] (II) modesetting(0): EDID (in hex):
[ 23.247] (II) modesetting(0): 00ffffffffffff0005e3432252280000
[ 23.247] (II) modesetting(0): 0516010368301b782a3585a656489a24
[ 23.247] (II) modesetting(0): 125054bfef00814081809500b300d1c0
[ 23.247] (II) modesetting(0): 010101010101023a801871382d40582c
[ 23.247] (II) modesetting(0): 4500dd0c1100001e000000fd00374b1e
[ 23.249] (II) modesetting(0): 5311000a202020202020000000fc0032
[ 23.249] (II) modesetting(0): 323433570a20202020202020000000ff
[ 23.249] (II) modesetting(0): 0041435943314f413031303332320064
[ 23.249] (II) modesetting(0): Printing probed modes for output VGA-0
[ 23.249] (II) modesetting(0): Modeline "1920x1080"x60.0 148.50 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync (67.5 kHz eP)
[ 23.249] (II) modesetting(0): Modeline "1680x1050"x60.0 146.25 1680 1784 1960 2240 1050 1053 1059 1089 -hsync +vsync (65.3 kHz e)
[ 23.249] (II) modesetting(0): Modeline "1680x945"x60.0 131.48 1680 1784 1960 2240 945 946 949 978 -hsync +vsync (58.7 kHz)
[ 23.249] (II) modesetting(0): Modeline "1400x1050"x74.9 156.00 1400 1504 1648 1896 1050 1053 1057 1099 -hsync +vsync (82.3 kHz e)
[ 23.249] (II) modesetting(0): Modeline "1400x1050"x60.0 121.75 1400 1488 1632 1864 1050 1053 1057 1089 -hsync +vsync (65.3 kHz e)
[ 23.250] (II) modesetting(0): Modeline "1600x900"x60.0 118.96 1600 1696 1864 2128 900 901 904 932 -hsync +vsync (55.9 kHz)
[ 23.250] (II) modesetting(0): Modeline "1280x1024"x75.0 135.00 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync (80.0 kHz e)
[ 23.250] (II) modesetting(0): Modeline "1280x1024"x60.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz e)
[ 23.250] (II) modesetting(0): Modeline "1440x900"x75.0 136.75 1440 1536 1688 1936 900 903 909 942 -hsync +vsync (70.6 kHz e)
[ 23.250] (II) modesetting(0): Modeline "1440x900"x59.9 106.50 1440 1520 1672 1904 900 903 909 934 -hsync +vsync (55.9 kHz e)
[ 23.250] (II) modesetting(0): Modeline "1280x960"x60.0 108.00 1280 1376 1488 1800 960 961 964 1000 +hsync +vsync (60.0 kHz e)
[ 23.250] (II) modesetting(0): Modeline "1366x768"x60.0 85.89 1366 1439 1583 1800 768 769 772 795 -hsync +vsync (47.7 kHz)
[ 23.250] (II) modesetting(0): Modeline "1360x768"x60.0 85.50 1360 1424 1536 1792 768 771 777 795 +hsync +vsync (47.7 kHz e)
[ 23.250] (II) modesetting(0): Modeline "1280x800"x74.9 106.50 1280 1360 1488 1696 800 803 809 838 -hsync +vsync (62.8 kHz e)
[ 23.250] (II) modesetting(0): Modeline "1280x800"x59.8 83.50 1280 1352 1480 1680 800 803 809 831 +hsync -vsync (49.7 kHz e)
[ 23.250] (II) modesetting(0): Modeline "1152x864"x75.0 108.00 1152 1216 1344 1600 864 865 868 900 +hsync +vsync (67.5 kHz e)
[ 23.251] (II) modesetting(0): Modeline "1280x768"x74.9 102.25 1280 1360 1488 1696 768 771 778 805 +hsync -vsync (60.3 kHz e)
[ 23.251] (II) modesetting(0): Modeline "1280x768"x59.9 79.50 1280 1344 1472 1664 768 771 778 798 -hsync +vsync (47.8 kHz e)
[ 23.251] (II) modesetting(0): Modeline "1024x768"x75.1 78.80 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.1 kHz e)
[ 23.251] (II) modesetting(0): Modeline "1024x768"x70.1 75.00 1024 1048 1184 1328 768 771 777 806 -hsync -vsync (56.5 kHz e)
[ 23.251] (II) modesetting(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e)
[ 23.251] (II) modesetting(0): Modeline "1024x576"x60.0 46.97 1024 1064 1168 1312 576 577 580 597 -hsync +vsync (35.8 kHz)
[ 23.251] (II) modesetting(0): Modeline "832x624"x74.6 57.28 832 864 928 1152 624 625 628 667 -hsync -vsync (49.7 kHz e)
[ 23.251] (II) modesetting(0): Modeline "800x600"x72.2 50.00 800 856 976 1040 600 637 643 666 +hsync +vsync (48.1 kHz e)
[ 23.251] (II) modesetting(0): Modeline "800x600"x75.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz e)
[ 23.251] (II) modesetting(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e)
[ 23.251] (II) modesetting(0): Modeline "800x600"x56.2 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz e)
[ 23.251] (II) modesetting(0): Modeline "848x480"x60.0 33.75 848 864 976 1088 480 486 494 517 +hsync +vsync (31.0 kHz e)
[ 23.252] (II) modesetting(0): Modeline "640x480"x72.8 31.50 640 664 704 832 480 489 491 520 -hsync -vsync (37.9 kHz e)
[ 23.252] (II) modesetting(0): Modeline "640x480"x75.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz e)
[ 23.252] (II) modesetting(0): Modeline "640x480"x66.7 30.24 640 704 768 864 480 483 486 525 -hsync -vsync (35.0 kHz e)
[ 23.252] (II) modesetting(0): Modeline "640x480"x60.0 25.20 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz e)
[ 23.253] (II) modesetting(0): Modeline "720x400"x70.1 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz e)
[ 23.253] (II) modesetting(0): Output LVDS-0 connected
[ 23.253] (II) modesetting(0): Output S-video-0 disconnected
[ 23.253] (II) modesetting(0): Output S-video-1 disconnected
[ 23.253] (II) modesetting(0): Output VGA-0 connected
[ 23.253] (II) modesetting(0): Using exact sizes for initial modes
[ 23.253] (II) modesetting(0): Output LVDS-0 using initial mode 1366x768
[ 23.253] (II) modesetting(0): Output VGA-0 using initial mode 1366x768
[ 23.253] (II) modesetting(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated.
[ 23.253] (==) modesetting(0): DPI set to (96, 96)
[ 23.253] (II) Loading sub module "fb"
[ 23.253] (II) LoadModule: "fb"
[ 23.255] (II) Loading /usr/lib/xorg/modules/libfb.so
[ 23.256] (II) Module fb: vendor="X.Org Foundation"
[ 23.256] compiled for 1.13.0, module version = 1.0.0
[ 23.256] ABI class: X.Org ANSI C Emulation, version 0.4
[ 23.256] (==) Depth 24 pixmap format is 32 bpp
[ 23.257] (==) modesetting(0): Backing store disabled
[ 23.257] (==) modesetting(0): Silken mouse enabled
[ 23.257] (II) modesetting(0): RandR 1.2 enabled, ignore the following RandR disabled message.
[ 23.259] (==) modesetting(0): DPMS enabled
[ 23.714] (--) RandR disabled
[ 23.785] (II) AIGLX: Screen 0 is not DRI2 capable
[ 23.785] (II) AIGLX: Screen 0 is not DRI capable
[ 24.380] (II) AIGLX: Loaded and initialized swrast
[ 24.380] (II) GLX: Initialized DRISWRAST GL provider for screen 0
[ 24.382] (II) modesetting(0): Damage tracking initialized
[ 24.382] (II) modesetting(0): Setting screen physical size to 361 x 203
[ 24.550] (II) XKB: reuse xkmfile /var/lib/xkb/server-B20D7FC79C7F597315E3E501AEF10E0D866E8E92.xkm
[ 24.568] (II) config/udev: Adding input device Video Bus (/dev/input/event6)
[ 24.568] (**) Video Bus: Applying InputClass "evdev keyboard catchall"
[ 24.568] (II) LoadModule: "evdev"
[ 24.578] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 24.594] (II) Module evdev: vendor="X.Org Foundation"
[ 24.594] compiled for 1.13.0, module version = 2.7.3
[ 24.594] Module class: X.Org XInput Driver
[ 24.594] ABI class: X.Org XInput driver, version 18.0
[ 24.595] (II) Using input driver 'evdev' for 'Video Bus'
[ 24.595] (**) Video Bus: always reports core events
[ 24.595] (**) evdev: Video Bus: Device: "/dev/input/event6"
[ 24.595] (--) evdev: Video Bus: Vendor 0 Product 0x6
[ 24.595] (--) evdev: Video Bus: Found keys
[ 24.595] (II) evdev: Video Bus: Configuring as keyboard
[ 24.595] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input7/event6"
[ 24.596] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 6)
[ 24.596] (**) Option "xkb_rules" "evdev"
[ 24.596] (**) Option "xkb_model" "pc105"
[ 24.596] (**) Option "xkb_layout" "us"
[ 24.598] (II) config/udev: Adding input device Power Button (/dev/input/event1)
[ 24.598] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 24.598] (II) Using input driver 'evdev' for 'Power Button'
[ 24.598] (**) Power Button: always reports core events
[ 24.598] (**) evdev: Power Button: Device: "/dev/input/event1"
[ 24.599] (--) evdev: Power Button: Vendor 0 Product 0x1
[ 24.599] (--) evdev: Power Button: Found keys
[ 24.599] (II) evdev: Power Button: Configuring as keyboard
[ 24.599] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1/event1"
[ 24.599] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 7)
[ 24.599] (**) Option "xkb_rules" "evdev"
[ 24.599] (**) Option "xkb_model" "pc105"
[ 24.599] (**) Option "xkb_layout" "us"
[ 24.601] (II) config/udev: Adding input device Lid Switch (/dev/input/event0)
[ 24.601] (II) No input driver specified, ignoring this device.
[ 24.601] (II) This device may have been added with another device file.
[ 24.603] (II) config/udev: Adding input device Sleep Button (/dev/input/event2)
[ 24.603] (**) Sleep Button: Applying InputClass "evdev keyboard catchall"
[ 24.603] (II) Using input driver 'evdev' for 'Sleep Button'
[ 24.603] (**) Sleep Button: always reports core events
[ 24.603] (**) evdev: Sleep Button: Device: "/dev/input/event2"
[ 24.603] (--) evdev: Sleep Button: Vendor 0 Product 0x3
[ 24.603] (--) evdev: Sleep Button: Found keys
[ 24.603] (II) evdev: Sleep Button: Configuring as keyboard
[ 24.603] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input2/event2"
[ 24.603] (II) XINPUT: Adding extended input device "Sleep Button" (type: KEYBOARD, id 8)
[ 24.603] (**) Option "xkb_rules" "evdev"
[ 24.604] (**) Option "xkb_model" "pc105"
[ 24.604] (**) Option "xkb_layout" "us"
[ 24.605] (II) config/udev: Adding drm device (/dev/dri/card0)
[ 24.607] (II) config/udev: Adding input device HDA Intel MID Mic (/dev/input/event10)
[ 24.607] (II) No input driver specified, ignoring this device.
[ 24.607] (II) This device may have been added with another device file.
[ 24.608] (II) config/udev: Adding input device HDA Intel MID Headphone (/dev/input/event11)
[ 24.608] (II) No input driver specified, ignoring this device.
[ 24.609] (II) This device may have been added with another device file.
[ 24.610] (II) config/udev: Adding input device Microsft Microsoft Wireless Desktop Receiver 3.1 (/dev/input/event4)
[ 24.610] (**) Microsft Microsoft Wireless Desktop Receiver 3.1: Applying InputClass "evdev keyboard catchall"
[ 24.610] (II) Using input driver 'evdev' for 'Microsft Microsoft Wireless Desktop Receiver 3.1'
[ 24.610] (**) Microsft Microsoft Wireless Desktop Receiver 3.1: always reports core events
[ 24.610] (**) evdev: Microsft Microsoft Wireless Desktop Receiver 3.1: Device: "/dev/input/event4"
[ 24.610] (--) evdev: Microsft Microsoft Wireless Desktop Receiver 3.1: Vendor 0x45e Product 0xf9
[ 24.610] (--) evdev: Microsft Microsoft Wireless Desktop Receiver 3.1: Found keys
[ 24.610] (II) evdev: Microsft Microsoft Wireless Desktop Receiver 3.1: Configuring as keyboard
[ 24.611] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.0/input/input5/event4"
[ 24.611] (II) XINPUT: Adding extended input device "Microsft Microsoft Wireless Desktop Receiver 3.1" (type: KEYBOARD, id 9)
[ 24.611] (**) Option "xkb_rules" "evdev"
[ 24.611] (**) Option "xkb_model" "pc105"
[ 24.611] (**) Option "xkb_layout" "us"
[ 24.613] (II) config/udev: Adding input device Microsft Microsoft Wireless Desktop Receiver 3.1 (/dev/input/event5)
[ 24.614] (**) Microsft Microsoft Wireless Desktop Receiver 3.1: Applying InputClass "evdev pointer catchall"
[ 24.614] (**) Microsft Microsoft Wireless Desktop Receiver 3.1: Applying InputClass "evdev keyboard catchall"
[ 24.614] (II) Using input driver 'evdev' for 'Microsft Microsoft Wireless Desktop Receiver 3.1'
[ 24.614] (**) Microsft Microsoft Wireless Desktop Receiver 3.1: always reports core events
[ 24.614] (**) evdev: Microsft Microsoft Wireless Desktop Receiver 3.1: Device: "/dev/input/event5"
[ 24.614] (--) evdev: Microsft Microsoft Wireless Desktop Receiver 3.1: Vendor 0x45e Product 0xf9
[ 24.614] (--) evdev: Microsft Microsoft Wireless Desktop Receiver 3.1: Found 9 mouse buttons
[ 24.614] (--) evdev: Microsft Microsoft Wireless Desktop Receiver 3.1: Found scroll wheel(s)
[ 24.614] (--) evdev: Microsft Microsoft Wireless Desktop Receiver 3.1: Found relative axes
[ 24.614] (--) evdev: Microsft Microsoft Wireless Desktop Receiver 3.1: Found x and y relative axes
[ 24.614] (--) evdev: Microsft Microsoft Wireless Desktop Receiver 3.1: Found absolute axes
[ 24.614] (II) evdev: Microsft Microsoft Wireless Desktop Receiver 3.1: Forcing absolute x/y axes to exist.
[ 24.614] (--) evdev: Microsft Microsoft Wireless Desktop Receiver 3.1: Found keys
[ 24.614] (II) evdev: Microsft Microsoft Wireless Desktop Receiver 3.1: Configuring as mouse
[ 24.615] (II) evdev: Microsft Microsoft Wireless Desktop Receiver 3.1: Configuring as keyboard
[ 24.615] (II) evdev: Microsft Microsoft Wireless Desktop Receiver 3.1: Adding scrollwheel support
[ 24.615] (**) evdev: Microsft Microsoft Wireless Desktop Receiver 3.1: YAxisMapping: buttons 4 and 5
[ 24.615] (**) evdev: Microsft Microsoft Wireless Desktop Receiver 3.1: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 24.615] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.1/input/input6/event5"
[ 24.615] (II) XINPUT: Adding extended input device "Microsft Microsoft Wireless Desktop Receiver 3.1" (type: KEYBOARD, id 10)
[ 24.615] (**) Option "xkb_rules" "evdev"
[ 24.615] (**) Option "xkb_model" "pc105"
[ 24.615] (**) Option "xkb_layout" "us"
[ 24.616] (II) evdev: Microsft Microsoft Wireless Desktop Receiver 3.1: initialized for relative axes.
[ 24.616] (WW) evdev: Microsft Microsoft Wireless Desktop Receiver 3.1: ignoring absolute axes.
[ 24.617] (**) Microsft Microsoft Wireless Desktop Receiver 3.1: (accel) keeping acceleration scheme 1
[ 24.617] (**) Microsft Microsoft Wireless Desktop Receiver 3.1: (accel) acceleration profile 0
[ 24.617] (**) Microsft Microsoft Wireless Desktop Receiver 3.1: (accel) acceleration factor: 2.000
[ 24.617] (**) Microsft Microsoft Wireless Desktop Receiver 3.1: (accel) acceleration threshold: 4
[ 24.618] (II) config/udev: Adding input device Microsft Microsoft Wireless Desktop Receiver 3.1 (/dev/input/mouse0)
[ 24.619] (II) No input driver specified, ignoring this device.
[ 24.619] (II) This device may have been added with another device file.
[ 24.620] (II) config/udev: Adding input device WebCam (/dev/input/event8)
[ 24.620] (**) WebCam: Applying InputClass "evdev keyboard catchall"
[ 24.620] (II) Using input driver 'evdev' for 'WebCam'
[ 24.620] (**) WebCam: always reports core events
[ 24.620] (**) evdev: WebCam: Device: "/dev/input/event8"
[ 24.621] (--) evdev: WebCam: Vendor 0x64e Product 0xa102
[ 24.621] (--) evdev: WebCam: Found keys
[ 24.621] (II) evdev: WebCam: Configuring as keyboard
[ 24.621] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.7/usb1/1-4/1-4:1.0/input/input9/event8"
[ 24.621] (II) XINPUT: Adding extended input device "WebCam" (type: KEYBOARD, id 11)
[ 24.621] (**) Option "xkb_rules" "evdev"
[ 24.621] (**) Option "xkb_model" "pc105"
[ 24.621] (**) Option "xkb_layout" "us"
[ 24.623] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event3)
[ 24.623] (**) AT Translated Set 2 keyboard: Applying InputClass "evdev keyboard catchall"
[ 24.624] (II) Using input driver 'evdev' for 'AT Translated Set 2 keyboard'
[ 24.624] (**) AT Translated Set 2 keyboard: always reports core events
[ 24.624] (**) evdev: AT Translated Set 2 keyboard: Device: "/dev/input/event3"
[ 24.624] (--) evdev: AT Translated Set 2 keyboard: Vendor 0x1 Product 0x1
[ 24.624] (--) evdev: AT Translated Set 2 keyboard: Found keys
[ 24.624] (II) evdev: AT Translated Set 2 keyboard: Configuring as keyboard
[ 24.624] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio0/input/input4/event3"
[ 24.624] (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD, id 12)
[ 24.624] (**) Option "xkb_rules" "evdev"
[ 24.624] (**) Option "xkb_model" "pc105"
[ 24.624] (**) Option "xkb_layout" "us"
[ 24.627] (II) config/udev: Adding input device SynPS/2 Synaptics TouchPad (/dev/input/event7)
[ 24.627] (**) SynPS/2 Synaptics TouchPad: Applying InputClass "evdev touchpad catchall"
[ 24.627] (**) SynPS/2 Synaptics TouchPad: Applying InputClass "touchpad catchall"
[ 24.627] (**) SynPS/2 Synaptics TouchPad: Applying InputClass "Default clickpad buttons"
[ 24.627] (II) LoadModule: "synaptics"
[ 24.628] (II) Loading /usr/lib/xorg/modules/input/synaptics_drv.so
[ 24.643] (II) Module synaptics: vendor="X.Org Foundation"
[ 24.644] compiled for 1.12.99.905, module version = 1.6.2
[ 24.644] Module class: X.Org XInput Driver
[ 24.644] ABI class: X.Org XInput driver, version 18.0
[ 24.644] (II) Using input driver 'synaptics' for 'SynPS/2 Synaptics TouchPad'
[ 24.644] (**) SynPS/2 Synaptics TouchPad: always reports core events
[ 24.644] (**) Option "Device" "/dev/input/event7"
[ 24.645] (II) synaptics: SynPS/2 Synaptics TouchPad: ignoring touch events for semi-multitouch device
[ 24.645] (--) synaptics: SynPS/2 Synaptics TouchPad: x-axis range 1472 - 5888
[ 24.645] (--) synaptics: SynPS/2 Synaptics TouchPad: y-axis range 1408 - 5012
[ 24.645] (--) synaptics: SynPS/2 Synaptics TouchPad: pressure range 0 - 255
[ 24.645] (--) synaptics: SynPS/2 Synaptics TouchPad: finger width range 0 - 15
[ 24.645] (--) synaptics: SynPS/2 Synaptics TouchPad: buttons: left right double triple
[ 24.645] (--) synaptics: SynPS/2 Synaptics TouchPad: Vendor 0x2 Product 0x7
[ 24.646] (--) synaptics: SynPS/2 Synaptics TouchPad: touchpad found
[ 24.646] (**) SynPS/2 Synaptics TouchPad: always reports core events
[ 24.646] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio2/input/input8/event7"
[ 24.646] (II) XINPUT: Adding extended input device "SynPS/2 Synaptics TouchPad" (type: TOUCHPAD, id 13)
[ 24.646] (**) synaptics: SynPS/2 Synaptics TouchPad: (accel) MinSpeed is now constant deceleration 2.5
[ 24.646] (**) synaptics: SynPS/2 Synaptics TouchPad: MaxSpeed is now 1.75
[ 24.646] (**) synaptics: SynPS/2 Synaptics TouchPad: AccelFactor is now 0.035
[ 24.647] (**) SynPS/2 Synaptics TouchPad: (accel) keeping acceleration scheme 1
[ 24.647] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration profile 1
[ 24.647] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration factor: 2.000
[ 24.647] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration threshold: 4
[ 24.647] (--) synaptics: SynPS/2 Synaptics TouchPad: touchpad found
[ 24.648] (II) config/udev: Adding input device SynPS/2 Synaptics TouchPad (/dev/input/mouse1)
[ 24.648] (**) SynPS/2 Synaptics TouchPad: Ignoring device from InputClass "touchpad ignore duplicates"
[ 24.657] (II) config/udev: Adding input device Acer BMA150 accelerometer (/dev/input/event9)
[ 24.658] (II) No input driver specified, ignoring this device.
[ 24.658] (II) This device may have been added with another device file.
[ 24.658] (II) config/udev: Adding input device Acer BMA150 accelerometer (/dev/input/js0)
[ 24.658] (II) No input driver specified, ignoring this device.
[ 24.659] (II) This device may have been added with another device file.
[ 256.088] (II) modesetting(0): EDID vendor "CMO", prod id 4352
[ 256.088] (II) modesetting(0): Printing DDC gathered Modelines:
[ 256.088] (II) modesetting(0): Modeline "1366x768"x0.0 69.30 1366 1398 1420 1474 768 770 774 784 -hsync -vsync (47.0 kHz eP)
[ 256.856] (II) modesetting(0): EDID vendor "CMO", prod id 4352
[ 256.856] (II) modesetting(0): Printing DDC gathered Modelines:
[ 256.856] (II) modesetting(0): Modeline "1366x768"x0.0 69.30 1366 1398 1420 1474 768 770 774 784 -hsync -vsync (47.0 kHz eP)
[ 257.503] (II) modesetting(0): EDID vendor "CMO", prod id 4352
[ 257.503] (II) modesetting(0): Printing DDC gathered Modelines:
[ 257.503] (II) modesetting(0): Modeline "1366x768"x0.0 69.30 1366 1398 1420 1474 768 770 774 784 -hsync -vsync (47.0 kHz eP)
[ 257.875] (II) modesetting(0): Allocate new frame buffer 1920x1080 stride
Re: 12.10 - Extended Desktop - How to change virtual desktop size?
Looks like nothing changed..
I don't recognise the "modesetting" driver label.
Sounds like a kms driver for the framebuffer for console & before the X server driver takes over..
could try
sudo Xorg -configure
- this will write a new xorg.conf file..
Your previous posted output from "lsmod | grep gma" does show the gma500_gfx loaded so maybe this is all you get..
Reading:
https://wiki.archlinux.org/index.php/Poulsbo
modesetting is the driver name of gma500_gfx