Baufrin
November 16th, 2008, 08:38 PM
I have never been able to get the wireless to work under ubuntu since 8.04. Please help. this is the information that is mentioned for submiting a ticket. Thanks for taking a look ( I am a noob in ubuntu)
1 ) Machine Brand and Model (PC/Laptop):
Code: HP Pavilion 9700 laptop (label also calls it a dv9910)
2 ) Wireless Brand, Model and Wireless Chipset:
Code: $ lspci -nn | grep 'Wireless Brand'
03:00.0 Ethernet controller [0200]: Atheros Communications Inc. AR242x 802.11abg Wireless PCI Express Adapter [168c:001c] (rev 01)
3 ) check interface:
Code:
$ ifconfig
eth0 Link encap:Ethernet HWaddr 00:1e:68:78:82:a5
inet addr:192.168.0.195 Bcast:192.168.0.255 Mask:255.255.255.0
inet6 addr: fe80::21e:68ff:fe78:82a5/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:12164 errors:0 dropped:0 overruns:0 frame:0
TX packets:4775 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:10851030 (10.8 MB) TX bytes:571411 (571.4 KB)
Interrupt:220 Base address:0x2000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:82 errors:0 dropped:0 overruns:0 frame:0
TX packets:82 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:4100 (4.1 KB) TX bytes:4100 (4.1 KB)
$ iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
pan0 no wireless extensions.
(hint) if the Wireless interface name is wlan0 you can also use
Code:
$ iwconfig wlan0
4 ) Check for modules:
Code:
$ lsmod
Module Size Used by
ipv6 263972 10
ndiswrapper 196380 0
bridge 56980 0
stp 10628 1 bridge
bnep 20480 2
sco 18308 2
rfcomm 44432 2
l2cap 30464 16 bnep,rfcomm
af_packet 25728 2
ppdev 15620 0
powernow_k8 22148 1
cpufreq_conservative 14600 0
cpufreq_ondemand 14988 1
cpufreq_userspace 11396 0
cpufreq_stats 13188 0
freq_table 12672 3 powernow_k8,cpufreq_ondemand,cpufreq_stats
cpufreq_powersave 9856 0
pci_slot 12552 0
container 11520 0
sbs 19464 0
sbshc 13440 1 sbs
iptable_filter 10752 0
ip_tables 19600 1 iptable_filter
x_tables 22916 1 ip_tables
sbp2 29324 0
parport_pc 39204 0
lp 17156 0
parport 42604 3 ppdev,parport_pc,lp
joydev 18368 0
serio_raw 13444 0
nvidia 7103300 36
agpgart 42184 1 nvidia
pcspkr 10624 0
psmouse 45200 0
k8temp 12416 0
uvcvideo 62728 0
shpchp 37908 0
pci_hotplug 35236 1 shpchp
i2c_core 31892 1 nvidia
compat_ioctl32 9344 1 uvcvideo
videodev 41344 1 uvcvideo
v4l1_compat 22404 2 uvcvideo,videodev
evdev 17696 12
btusb 19736 3
bluetooth 61924 11 bnep,sco,rfcomm,l2cap,btusb
sdhci_pci 15360 0
sdhci 23940 1 sdhci_pci
mmc_core 58268 1 sdhci
video 25104 5
ricoh_mmc 11904 0
output 11008 1 video
snd_hda_intel 381488 2
snd_pcm_oss 46848 0
snd_mixer_oss 22784 1 snd_pcm_oss
snd_pcm 83204 2 snd_hda_intel,snd_pcm_oss
snd_seq_dummy 10884 0
snd_seq_oss 38528 0
snd_seq_midi 14336 0
snd_rawmidi 29824 1 snd_seq_midi
snd_seq_midi_event 15232 2 snd_seq_oss,snd_seq_midi
wmi 14504 0
battery 18436 0
snd_seq 57776 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_mid i_event
snd_timer 29960 2 snd_pcm,snd_seq
snd_seq_device 15116 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi ,snd_seq
snd 63268 13 snd_hda_intel,snd_pcm_oss,snd_mixer_oss,snd_pcm,sn d_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_de vice
button 14224 0
ac 12292 0
soundcore 15328 1 snd
snd_page_alloc 16136 2 snd_hda_intel,snd_pcm
ext3 133384 1
jbd 55444 1 ext3
mbcache 16004 1 ext3
sd_mod 42264 3
crc_t10dif 9984 1 sd_mod
usbhid 35840 0
hid 50560 1 usbhid
sr_mod 22212 0
cdrom 43168 1 sr_mod
sg 39732 0
pata_acpi 12160 0
ata_generic 12932 0
pata_amd 18692 0
ahci 37132 2
ohci1394 37936 0
forcedeth 61328 0
ohci_hcd 31888 0
libata 177312 4 pata_acpi,ata_generic,pata_amd,ahci
scsi_mod 155212 5 sbp2,sd_mod,sr_mod,sg,libata
ehci_hcd 43276 0
ieee1394 96324 2 sbp2,ohci1394
usbcore 148848 7 ndiswrapper,uvcvideo,btusb,usbhid,ohci_hcd,ehci_hc d
dock 16656 1 libata
thermal 23708 0
processor 42156 4 powernow_k8,thermal
fan 12548 0
fbcon 47648 0
tileblit 10880 1 fbcon
font 16512 1 fbcon
bitblit 13824 1 fbcon
softcursor 9984 1 bitblit
fuse 60828 3
$ lsmod | grep "wlan_module_name"
5 ) Kernel boot messages
Code:
$ dmesg
[ 0.516692] PCI: 0000:00:09.0 reg 14 io port: [30e4, 30e7]
[ 0.516696] PCI: 0000:00:09.0 reg 18 io port: [30e8, 30ef]
[ 0.516700] PCI: 0000:00:09.0 reg 1c io port: [30e0, 30e3]
[ 0.516704] PCI: 0000:00:09.0 reg 20 io port: [30d0, 30df]
[ 0.516708] PCI: 0000:00:09.0 reg 24 32bit mmio: [f6484000, f6485fff]
[ 0.516748] PCI: 0000:00:0a.0 reg 10 32bit mmio: [f6488000, f6488fff]
[ 0.516752] PCI: 0000:00:0a.0 reg 14 io port: [30f8, 30ff]
[ 0.516756] PCI: 0000:00:0a.0 reg 18 32bit mmio: [f6489c00, f6489cff]
[ 0.516761] PCI: 0000:00:0a.0 reg 1c 32bit mmio: [f6489800, f648980f]
[ 0.516779] pci 0000:00:0a.0: supports D1
[ 0.516780] pci 0000:00:0a.0: supports D2
[ 0.516782] pci 0000:00:0a.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.516787] pci 0000:00:0a.0: PME# disabled
[ 0.516816] pci 0000:00:0c.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.516819] pci 0000:00:0c.0: PME# disabled
[ 0.516845] pci 0000:00:0d.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.516848] pci 0000:00:0d.0: PME# disabled
[ 0.516866] PCI: 0000:00:12.0 reg 10 32bit mmio: [f5000000, f5ffffff]
[ 0.516870] PCI: 0000:00:12.0 reg 14 32bit mmio: [d0000000, dfffffff]
[ 0.516877] PCI: 0000:00:12.0 reg 1c 64bit mmio: [f4000000, f4ffffff]
[ 0.516883] PCI: 0000:00:12.0 reg 30 32bit mmio: [0, 1ffff]
[ 0.516986] PCI: 0000:02:05.0 reg 10 32bit mmio: [0, 7ff]
[ 0.517017] pci 0000:02:05.0: supports D1
[ 0.517019] pci 0000:02:05.0: supports D2
[ 0.517021] pci 0000:02:05.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.517025] pci 0000:02:05.0: PME# disabled
[ 0.517046] PCI: 0000:02:05.1 reg 10 32bit mmio: [f6100800, f61008ff]
[ 0.517077] pci 0000:02:05.1: supports D1
[ 0.517078] pci 0000:02:05.1: supports D2
[ 0.517080] pci 0000:02:05.1: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.517084] pci 0000:02:05.1: PME# disabled
[ 0.517105] PCI: 0000:02:05.2 reg 10 32bit mmio: [f6100c00, f6100cff]
[ 0.517136] pci 0000:02:05.2: supports D1
[ 0.517137] pci 0000:02:05.2: supports D2
[ 0.517140] pci 0000:02:05.2: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.517144] pci 0000:02:05.2: PME# disabled
[ 0.517164] PCI: 0000:02:05.3 reg 10 32bit mmio: [f6101000, f61010ff]
[ 0.517195] pci 0000:02:05.3: supports D1
[ 0.517197] pci 0000:02:05.3: supports D2
[ 0.517199] pci 0000:02:05.3: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.517203] pci 0000:02:05.3: PME# disabled
[ 0.517225] PCI: 0000:02:05.4 reg 10 32bit mmio: [f6101400, f61014ff]
[ 0.517256] pci 0000:02:05.4: supports D1
[ 0.517258] pci 0000:02:05.4: supports D2
[ 0.517260] pci 0000:02:05.4: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.517264] pci 0000:02:05.4: PME# disabled
[ 0.517293] pci 0000:00:08.0: transparent bridge
[ 0.517298] PCI: bridge 0000:00:08.0 32bit mmio: [f6100000, f61fffff]
[ 0.517337] PCI: bridge 0000:00:0c.0 io port: [4000, 4fff]
[ 0.517340] PCI: bridge 0000:00:0c.0 32bit mmio: [f2000000, f3ffffff]
[ 0.517344] PCI: bridge 0000:00:0c.0 64bit mmio pref: [f0000000, f1ffffff]
[ 0.517379] PCI: 0000:03:00.0 reg 10 64bit mmio: [f6000000, f600ffff]
[ 0.517449] PCI: bridge 0000:00:0d.0 32bit mmio: [f6000000, f60fffff]
[ 0.517459] bus 00 -> node 0
[ 0.517466] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.517575] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P0._PRT]
[ 0.517600] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR1._PRT]
[ 0.517640] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR2._PRT]
[ 0.557911] ACPI: PCI Interrupt Link [LNK1] (IRQs 5) *10
[ 0.557911] ACPI: PCI Interrupt Link [LNK2] (IRQs 7) *11
[ 0.557911] ACPI: PCI Interrupt Link [LNK3] (IRQs 10) *0, disabled.
[ 0.557911] ACPI: PCI Interrupt Link [LNK4] (IRQs 11) *0, disabled.
[ 0.557911] ACPI: PCI Interrupt Link [LK1E] (IRQs 16) *0, disabled.
[ 0.557911] ACPI: PCI Interrupt Link [LK2E] (IRQs 17) *0, disabled.
[ 0.557911] ACPI: PCI Interrupt Link [LK3E] (IRQs 18) *0, disabled.
[ 0.558139] ACPI: PCI Interrupt Link [LK4E] (IRQs 19) *10
[ 0.558405] ACPI: PCI Interrupt Link [LSMB] (IRQs *10)
[ 0.558671] ACPI: PCI Interrupt Link [LUS0] (IRQs 18) *11
[ 0.558938] ACPI: PCI Interrupt Link [LUS2] (IRQs 22) *7
[ 0.559210] ACPI: PCI Interrupt Link [LMAC] (IRQs 20) *11
[ 0.559478] ACPI: PCI Interrupt Link [LAZA] (IRQs 21) *10
[ 0.559745] ACPI: PCI Interrupt Link [LGPU] (IRQs 16) *10
[ 0.560021] ACPI: PCI Interrupt Link [LPID] (IRQs 22) *0, disabled.
[ 0.560299] ACPI: PCI Interrupt Link [LSI0] (IRQs 23) *11
[ 0.560567] ACPI: PCI Interrupt Link [Z018] (IRQs 18) *5
[ 0.560838] ACPI: PCI Interrupt Link [Z019] (IRQs 22) *10
[ 0.561110] ACPI: PCI Interrupt Link [LPMU] (IRQs *11)
[ 0.564161] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 0.564183] pnp: PnP ACPI init
[ 0.564183] ACPI: bus type pnp registered
[ 0.569276] pnp: PnP ACPI: found 12 devices
[ 0.569276] ACPI: ACPI bus type pnp unregistered
[ 0.569276] PnPBIOS: Disabled by ACPI PNP
[ 0.569276] PCI: Using ACPI for IRQ routing
[ 0.572045] NET: Registered protocol family 8
[ 0.572047] NET: Registered protocol family 20
[ 0.576040] NetLabel: Initializing
[ 0.576040] NetLabel: domain hash size = 128
[ 0.576040] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.576055] NetLabel: unlabeled traffic allowed by default
[ 0.576064] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 31
[ 0.576069] hpet0: 3 32-bit timers, 25000000 Hz
[ 0.577648] tracer: 772 pages allocated for 65536 entries of 48 bytes
[ 0.577651] actual entries 65620
[ 0.577797] AppArmor: AppArmor Filesystem Enabled
[ 0.577825] ACPI: RTC can wake from S4
[ 0.580051] Switched to high resolution mode on CPU 0
[ 0.580065] Switched to high resolution mode on CPU 1
[ 0.580095] system 00:02: iomem range 0xe0000000-0xefffffff could not be reserved
[ 0.580102] system 00:03: ioport range 0x1000-0x107f has been reserved
[ 0.580106] system 00:03: ioport range 0x1080-0x10ff has been reserved
[ 0.580109] system 00:03: ioport range 0x1400-0x147f has been reserved
[ 0.580112] system 00:03: ioport range 0x1480-0x14ff has been reserved
[ 0.580115] system 00:03: ioport range 0x1800-0x187f has been reserved
[ 0.580118] system 00:03: ioport range 0x1880-0x18ff has been reserved
[ 0.580125] system 00:04: ioport range 0x360-0x361 has been reserved
[ 0.580128] system 00:04: ioport range 0x4d0-0x4d1 has been reserved
[ 0.580139] system 00:0b: iomem range 0xffc00000-0xffffffff could not be reserved
[ 0.580143] system 00:0b: iomem range 0xfec00000-0xfec00fff could not be reserved
[ 0.580146] system 00:0b: iomem range 0xfee00000-0xfeefffff could not be reserved
[ 0.580150] system 00:0b: iomem range 0xfed00000-0xfed00fff has been reserved
[ 0.580153] system 00:0b: iomem range 0xfef00000-0xfef00fff has been reserved
[ 0.615468] pci 0000:00:08.0: PCI bridge, secondary bus 0000:02
[ 0.615471] pci 0000:00:08.0: IO window: disabled
[ 0.615475] pci 0000:00:08.0: MEM window: 0xf6100000-0xf61fffff
[ 0.615478] pci 0000:00:08.0: PREFETCH window: disabled
[ 0.615483] pci 0000:00:0c.0: PCI bridge, secondary bus 0000:04
[ 0.615486] pci 0000:00:0c.0: IO window: 0x4000-0x4fff
[ 0.615489] pci 0000:00:0c.0: MEM window: 0xf2000000-0xf3ffffff
[ 0.615493] pci 0000:00:0c.0: PREFETCH window: 0x000000f0000000-0x000000f1ffffff
[ 0.615497] pci 0000:00:0d.0: PCI bridge, secondary bus 0000:03
[ 0.615499] pci 0000:00:0d.0: IO window: disabled
[ 0.615503] pci 0000:00:0d.0: MEM window: 0xf6000000-0xf60fffff
[ 0.615506] pci 0000:00:0d.0: PREFETCH window: disabled
[ 0.615516] pci 0000:00:08.0: setting latency timer to 64
[ 0.615521] pci 0000:00:0c.0: setting latency timer to 64
[ 0.615526] pci 0000:00:0d.0: setting latency timer to 64
[ 0.615530] bus: 00 index 0 io port: [0, ffff]
[ 0.615532] bus: 00 index 1 mmio: [0, ffffffff]
[ 0.615534] bus: 02 index 0 mmio: [0, 0]
[ 0.615536] bus: 02 index 1 mmio: [f6100000, f61fffff]
[ 0.615539] bus: 02 index 2 mmio: [0, 0]
[ 0.615541] bus: 02 index 3 io port: [0, ffff]
[ 0.615543] bus: 02 index 4 mmio: [0, ffffffff]
[ 0.615545] bus: 04 index 0 io port: [4000, 4fff]
[ 0.615548] bus: 04 index 1 mmio: [f2000000, f3ffffff]
[ 0.615550] bus: 04 index 2 mmio: [f0000000, f1ffffff]
[ 0.615553] bus: 04 index 3 mmio: [0, 0]
[ 0.615555] bus: 03 index 0 mmio: [0, 0]
[ 0.615557] bus: 03 index 1 mmio: [f6000000, f60fffff]
[ 0.615559] bus: 03 index 2 mmio: [0, 0]
[ 0.615561] bus: 03 index 3 mmio: [0, 0]
[ 0.615574] NET: Registered protocol family 2
[ 0.625077] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.625380] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.626181] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.626632] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.626636] TCP reno registered
[ 0.629120] NET: Registered protocol family 1
[ 0.629249] checking if image is initramfs... it is
[ 1.322651] Freeing initrd memory: 7932k freed
[ 1.322824] Simple Boot Flag at 0x36 set to 0x1
[ 1.324095] audit: initializing netlink socket (disabled)
[ 1.324111] type=2000 audit(1226798723.324:1): initialized
[ 1.330205] highmem bounce pool size: 64 pages
[ 1.330211] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 1.333130] VFS: Disk quotas dquot_6.5.1
[ 1.333232] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.333364] msgmni has been set to 1726
[ 1.333495] io scheduler noop registered
[ 1.333497] io scheduler anticipatory registered
[ 1.333500] io scheduler deadline registered
[ 1.333512] io scheduler cfq registered (default)
[ 1.333545] pci 0000:00:00.0: Enabling HT MSI Mapping
[ 1.333705] pci 0000:00:07.0: Enabling HT MSI Mapping
[ 1.333721] pci 0000:00:08.0: Enabling HT MSI Mapping
[ 1.333737] pci 0000:00:09.0: Enabling HT MSI Mapping
[ 1.333754] pci 0000:00:0a.0: Enabling HT MSI Mapping
[ 1.333769] pci 0000:00:0c.0: Enabling HT MSI Mapping
[ 1.333785] pci 0000:00:0d.0: Enabling HT MSI Mapping
[ 1.333800] pci 0000:00:12.0: Boot video device
[ 1.333940] pcieport-driver 0000:00:0c.0: setting latency timer to 64
[ 1.333965] pcieport-driver 0000:00:0c.0: found MSI capability
[ 1.333987] pci_express 0000:00:0c.0:pcie00: allocate port service
[ 1.334045] pci_express 0000:00:0c.0:pcie03: allocate port service
[ 1.334133] pcieport-driver 0000:00:0d.0: setting latency timer to 64
[ 1.334159] pcieport-driver 0000:00:0d.0: found MSI capability
[ 1.334177] pci_express 0000:00:0d.0:pcie00: allocate port service
[ 1.334231] pci_express 0000:00:0d.0:pcie03: allocate port service
[ 1.334636] isapnp: Scanning for PnP cards...
[ 1.687211] isapnp: No Plug & Play device found
[ 1.730977] hpet_resources: 0xfed00000 is busy
[ 1.731088] Serial: 8250/16550 driver4 ports, IRQ sharing enabled
[ 1.733837] brd: module loaded
[ 1.733921] input: Macintosh mouse button emulation as /devices/virtual/input/input0
[ 1.734064] PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12
[ 1.762783] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.762790] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.763178] mice: PS/2 mouse device common for all mice
[ 1.763330] rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0
[ 1.763364] rtc0: alarms up to one year, y3k, hpet irqs
[ 1.763502] EISA: Probing bus 0 at eisa.0
[ 1.763508] Cannot allocate resource for EISA slot 1
[ 1.763513] Cannot allocate resource for EISA slot 3
[ 1.763516] Cannot allocate resource for EISA slot 4
[ 1.763530] EISA: Detected 0 cards.
[ 1.763534] cpuidle: using governor ladder
[ 1.763537] cpuidle: using governor menu
[ 1.764034] TCP cubic registered
[ 1.764062] Using IPI No-Shortcut mode
[ 1.764280] registered taskstats version 1
[ 1.764421] Magic number: 0:709:407
[ 1.764577] acpi PNP0800:00: hash matches
[ 1.764589] acpi ACPI0003:00: hash matches
[ 1.764635] rtc_cmos 00:07: setting system clock to 2008-11-16 01:25:24 UTC (1226798724)
[ 1.764638] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 1.764641] EDD information not available.
[ 1.764953] Freeing unused kernel memory: 424k freed
[ 1.765039] Write protecting the kernel text: 2576k
[ 1.765080] Write protecting the kernel read-only data: 936k
[ 1.784619] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
[ 1.900407] fuse init (API version 7.9)
[ 2.026738] ACPI: processor limited to max C-state 1
[ 2.026931] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[ 2.027021] processor ACPI0007:00: registered as cooling_device0
[ 2.027027] ACPI: Processor [CPU0] (supports 8 throttling states)
[ 2.027245] ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
[ 2.027319] processor ACPI0007:01: registered as cooling_device1
[ 2.027324] ACPI: Processor [CPU1] (supports 8 throttling states)
[ 2.030097] ACPI Exception (thermal-0377): AE_OK, No or invalid critical threshold [20080609]
[ 2.504261] No dock devices found.
[ 2.542304] usbcore: registered new interface driver usbfs
[ 2.542327] usbcore: registered new interface driver hub
[ 2.542397] usbcore: registered new device driver usb
[ 2.545603] ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 22
[ 2.545616] ehci_hcd 0000:00:02.1: PCI INT B -> Link[LUS2] -> GSI 22 (level, low) -> IRQ 22
[ 2.545628] ehci_hcd 0000:00:02.1: setting latency timer to 64
[ 2.545631] ehci_hcd 0000:00:02.1: EHCI Host Controller
[ 2.545681] ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1
[ 2.545710] ehci_hcd 0000:00:02.1: debug port 1
[ 2.545715] ehci_hcd 0000:00:02.1: cache line size of 64 is not supported
[ 2.545731] ehci_hcd 0000:00:02.1: irq 22, io mem 0xf6489000
[ 2.559461] ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 2.559624] usb usb1: configuration #1 chosen from 1 choice
[ 2.559657] hub 1-0:1.0: USB hub found
[ 2.559667] hub 1-0:1.0: 7 ports detected
[ 2.560227] SCSI subsystem initialized
[ 2.579472] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.579614] libata version 3.00 loaded.
[ 2.765893] ACPI: PCI Interrupt Link [Z019] enabled at IRQ 22
[ 2.765901] ehci_hcd 0000:00:04.1: PCI INT B -> Link[Z019] -> GSI 22 (level, low) -> IRQ 22
[ 2.765917] ehci_hcd 0000:00:04.1: setting latency timer to 64
[ 2.765920] ehci_hcd 0000:00:04.1: EHCI Host Controller
[ 2.765947] ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 2
[ 2.765976] ehci_hcd 0000:00:04.1: debug port 1
[ 2.765981] ehci_hcd 0000:00:04.1: cache line size of 64 is not supported
[ 2.765989] ehci_hcd 0000:00:04.1: irq 22, io mem 0xf6489400
[ 2.777030] ehci_hcd 0000:00:04.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 2.777219] usb usb2: configuration #1 chosen from 1 choice
[ 2.777247] hub 2-0:1.0: USB hub found
[ 2.777257] hub 2-0:1.0: 2 ports detected
[ 8.188951] ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 18
[ 8.188964] ohci_hcd 0000:00:02.0: PCI INT A -> Link[LUS0] -> GSI 18 (level, low) -> IRQ 18
[ 8.188979] ohci_hcd 0000:00:02.0: setting latency timer to 64
[ 8.188982] ohci_hcd 0000:00:02.0: OHCI Host Controller
[ 8.189012] Clocksource tsc unstable (delta = 4398044243638 ns)
[ 8.189031] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 3
[ 8.189055] ohci_hcd 0000:00:02.0: irq 18, io mem 0xf6486000
[ 8.432377] usb usb3: configuration #1 chosen from 1 choice
[ 8.432407] hub 3-0:1.0: USB hub found
[ 8.432418] hub 3-0:1.0: 7 ports detected
[ 8.616378] usb 2-2: new high speed USB device using ehci_hcd and address 3
[ 8.663985] ACPI: PCI Interrupt Link [Z018] enabled at IRQ 18
[ 8.663991] ohci_hcd 0000:00:04.0: PCI INT A -> Link[Z018] -> GSI 18 (level, low) -> IRQ 18
[ 8.664006] ohci_hcd 0000:00:04.0: setting latency timer to 64
[ 8.664009] ohci_hcd 0000:00:04.0: OHCI Host Controller
[ 8.664039] ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 4
[ 8.664053] ohci_hcd 0000:00:04.0: irq 18, io mem 0xf6487000
[ 8.743512] usb usb4: configuration #1 chosen from 1 choice
[ 8.743541] hub 4-0:1.0: USB hub found
[ 8.743552] hub 4-0:1.0: 2 ports detected
[ 8.871849] usb 2-2: configuration #1 chosen from 1 choice
[ 8.961117] pata_amd 0000:00:06.0: version 0.3.10
[ 8.961165] pata_amd 0000:00:06.0: setting latency timer to 64
[ 8.961590] scsi0 : pata_amd
[ 8.961981] scsi1 : pata_amd
[ 8.962392] ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0x30c0 irq 14
[ 8.962396] ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x30c8 irq 15
[ 9.053828] usb 3-5: new low speed USB device using ohci_hcd and address 2
[ 9.148076] ata1.00: ATAPI: PIONEER DVDRW DR-KD08HB, 1K09, max MWDMA2
[ 9.148090] ata1: nv_mode_filter: 0x39f&0x39f->0x39f, BIOS=0x0 (0xc600) ACPI=0x39f (120:600:0x12)
[ 9.210577] ata1.00: configured for MWDMA2
[ 9.210619] ata2: port disabled. ignoring.
[ 9.249308] scsi 0:0:0:0: CD-ROM PIONEER DVDRW DR-KD08HB 1K09 PQ: 0 ANSI: 5
[ 9.249497] ahci 0000:00:09.0: version 3.0
[ 9.249918] ACPI: PCI Interrupt Link [LSI0] enabled at IRQ 23
[ 9.249929] ahci 0000:00:09.0: PCI INT A -> Link[LSI0] -> GSI 23 (level, low) -> IRQ 23
[ 9.250019] ahci 0000:00:09.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl IDE mode
[ 9.250024] ahci 0000:00:09.0: flags: 64bit sntf led clo pmp pio slum part
[ 9.250027] ahci 0000:00:09.0: setting latency timer to 64
[ 9.251038] scsi2 : ahci
[ 9.251496] scsi3 : ahci
[ 9.251952] scsi4 : ahci
[ 9.253126] scsi5 : ahci
[ 9.253242] ata3: SATA max UDMA/133 abar m8192@0xf6484000 port 0xf6484100 irq 221
[ 9.253245] ata4: SATA max UDMA/133 abar m8192@0xf6484000 port 0xf6484180 irq 221
[ 9.253248] ata5: SATA max UDMA/133 abar m8192@0xf6484000 port 0xf6484200 irq 221
[ 9.253252] ata6: SATA max UDMA/133 abar m8192@0xf6484000 port 0xf6484280 irq 221
[ 9.291704] usb 3-5: configuration #1 chosen from 1 choice
[ 9.491949] usb 4-1: new full speed USB device using ohci_hcd and address 2
[ 9.776574] usb 4-1: configuration #1 chosen from 1 choice
[ 9.804218] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 9.804635] ata3.00: ATA-8: TOSHIBA MK2552GSX, LV012C, max UDMA/100
[ 9.804638] ata3.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 9.805128] ata3.00: configured for UDMA/100
[ 10.179628] ata4: SATA link down (SStatus 0 SControl 300)
[ 10.554500] ata5: SATA link down (SStatus 0 SControl 300)
[ 10.930645] ata6: SATA link down (SStatus 0 SControl 300)
[ 10.930754] scsi 2:0:0:0: Direct-Access ATA TOSHIBA MK2552GS LV01 PQ: 0 ANSI: 5
[ 10.930861] forcedeth: Reverse Engineered nForce ethernet driver. Version 0.61.
[ 10.931297] ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 20
[ 10.931308] forcedeth 0000:00:0a.0: PCI INT A -> Link[LMAC] -> GSI 20 (level, low) -> IRQ 20
[ 10.931313] forcedeth 0000:00:0a.0: setting latency timer to 64
[ 11.493107] forcedeth 0000:00:0a.0: ifname eth0, PHY OUI 0x732 @ 1, addr 00:1e:68:78:82:a5
[ 11.493111] forcedeth 0000:00:0a.0: highdma pwrctl mgmt timirq lnktim msi desc-v3
[ 11.494949] ohci1394 0000:02:05.0: enabling device (0100 -> 0102)
[ 11.495376] ACPI: PCI Interrupt Link [LNK1] enabled at IRQ 5
[ 11.495389] ohci1394 0000:02:05.0: PCI INT A -> Link[LNK1] -> GSI 5 (level, low) -> IRQ 5
[ 11.547123] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[5] MMIO=[f6100000-f61007ff] Max Packet=[2048] IR/IT contexts=[4/4]
[ 11.593228] scsi 0:0:0:0: Attached scsi generic sg0 type 5
[ 11.594230] scsi 2:0:0:0: Attached scsi generic sg1 type 0
[ 11.615666] Driver 'sr' needs updating - please use bus_type methods
[ 11.626710] usbcore: registered new interface driver hiddev
[ 11.632231] Driver 'sd' needs updating - please use bus_type methods
[ 11.636694] input: Razer Razer Diamondback Optical Mouse as /devices/pci0000:00/0000:00:02.0/usb3/3-5/3-5:1.0/input/input2
[ 11.654718] input,hidraw0: USB HID v1.10 Mouse [Razer Razer Diamondback Optical Mouse] on usb-0000:00:02.0-5
[ 11.654746] usbcore: registered new interface driver usbhid
[ 11.654750] usbhid: v2.6:USB HID core driver
[ 11.743384] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[ 11.743390] Uniform CD-ROM driver Revision: 3.20
[ 11.743493] sr 0:0:0:0: Attached scsi CD-ROM sr0
[ 11.743619] sd 2:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB)
[ 11.743640] sd 2:0:0:0: [sda] Write Protect is off
[ 11.743643] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 11.743679] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 11.743750] sd 2:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB)
[ 11.743767] sd 2:0:0:0: [sda] Write Protect is off
[ 11.743770] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 11.743802] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 11.743806] sda: sda1 sda2 sda3 < sda5 sda6 >
[ 11.870576] sd 2:0:0:0: [sda] Attached SCSI disk
[ 13.740127] PM: Starting manual resume from disk
[ 13.740131] PM: Resume from partition 8:6
[ 13.740133] PM: Checking hibernation image.
[ 13.740268] PM: Resume from disk failed.
[ 13.796622] kjournald starting. Commit interval 5 seconds
[ 13.796648] EXT3-fs: mounted filesystem with ordered data mode.
[ 14.013217] ieee1394: Host added: ID:BUS[0-00:1023] GUID[00241b00311f0001]
[ 25.267244] udevd version 124 started
[ 25.853160] ACPI: AC Adapter [ACAD] (on-line)
[ 25.925195] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[ 25.949035] ACPI: Power Button (FF) [PWRF]
[ 25.949167] input: Sleep Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input4
[ 25.981060] ACPI: Sleep Button (CM) [SLPB]
[ 25.981150] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input5
[ 25.981610] ACPI: Lid Switch [LID]
[ 25.981708] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input6
[ 26.009044] ACPI: Power Button (CM) [PWRB]
[ 26.329541] ACPI: Battery Slot [BAT0] (battery present)
[ 26.329829] ACPI: WMI: Mapper loaded
[ 26.931657] ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 21
[ 26.931671] HDA Intel 0000:00:07.0: PCI INT A -> Link[LAZA] -> GSI 21 (level, low) -> IRQ 21
[ 26.931700] HDA Intel 0000:00:07.0: setting latency timer to 64
[ 26.952170] ricoh-mmc: Ricoh MMC Controller disabling driver
[ 26.952174] ricoh-mmc: Copyright(c) Philip Langdale
[ 26.971601] acpi device:25: registered as cooling_device2
[ 26.971806] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:23/input/input7
[ 26.975085] sdhci: Secure Digital Host Controller Interface driver
[ 26.975089] sdhci: Copyright(c) Pierre Ossman
[ 26.992031] ACPI: Video Device [UVGA] (multi-head: yes rom: no post: no)
[ 26.994523] ricoh-mmc: Ricoh MMC controller found at 0000:02:05.2 [1180:0843] (rev 12)
[ 26.994539] ricoh-mmc: Controller is now disabled.
[ 27.022773] sdhci-pci 0000:02:05.1: SDHCI controller found [1180:0822] (rev 22)
[ 27.023199] ACPI: PCI Interrupt Link [LNK2] enabled at IRQ 7
[ 27.023211] sdhci-pci 0000:02:05.1: PCI INT B -> Link[LNK2] -> GSI 7 (level, low) -> IRQ 7
[ 27.026267] mmc0: SDHCI controller on PCI [0000:02:05.1] using PIO
[ 27.093785] Bluetooth: Core ver 2.13
[ 27.094344] NET: Registered protocol family 31
[ 27.094347] Bluetooth: HCI device and connection manager initialized
[ 27.094351] Bluetooth: HCI socket layer initialized
[ 27.138228] Bluetooth: Generic Bluetooth USB driver ver 0.3
[ 27.138335] usbcore: registered new interface driver btusb
[ 27.378111] Linux video capture interface: v2.00
[ 27.450762] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 27.455928] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 27.502658] uvcvideo: Found UVC 1.00 device HP Webcam (0c45:62c0)
[ 27.506268] input: HP Webcam as /devices/pci0000:00/0000:00:04.1/usb2/2-2/2-2:1.0/input/input8
[ 27.525247] usbcore: registered new interface driver uvcvideo
[ 27.525268] USB Video Class driver (v0.1.0)
[ 27.687141] input: PC Speaker as /devices/platform/pcspkr/input/input9
[ 27.697227] Linux agpgart interface v0.103
[ 27.758966] ndiswrapper version 1.53 loaded (smp=yes, preempt=no)
[ 28.522465] ACPI: PCI Interrupt Link [LGPU] enabled at IRQ 16
[ 28.522480] nvidia 0000:00:12.0: PCI INT A -> Link[LGPU] -> GSI 16 (level, low) -> IRQ 16
[ 28.522487] nvidia 0000:00:12.0: setting latency timer to 64
[ 28.522745] NVRM: loading NVIDIA UNIX x86 Kernel Module 173.14.12 Thu Jul 17 18:11:36 PDT 2008
[ 28.525437] usbcore: registered new interface driver ndiswrapper
[ 28.532540] Synaptics Touchpad, model: 1, fw: 6.3, id: 0x1a0b1, caps: 0xa04711/0xa00000
[ 28.609564] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input10
[ 29.266480] lp: driver loaded but no devices found
[ 29.444744] Adding 2602488k swap on /dev/sda6. Priority:-1 extents:1 across:2602488k
[ 73.198487] EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
[ 73.198673] EXT3 FS on sda5, internal journal
[ 74.252977] type=1505 audit(1226816797.167:2): operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" name2="default" pid=4798
[ 74.456521] type=1505 audit(1226816797.368:3): operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" name2="default" pid=4803
[ 74.456781] type=1505 audit(1226816797.368:4): operation="profile_load" name="/usr/sbin/cupsd" name2="default" pid=4803
[ 74.617254] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 75.422192] powernow-k8: Found 1 AMD Turion(tm) 64 X2 Mobile Technology TL-60 processors (2 cpu cores) (version 2.20.00)
[ 75.422838] powernow-k8: 0 : fid 0xc (2000 MHz), vid 0x11
[ 75.422843] powernow-k8: 1 : fid 0xa (1800 MHz), vid 0x12
[ 75.422845] powernow-k8: 2 : fid 0x8 (1600 MHz), vid 0x13
[ 75.422848] powernow-k8: 3 : fid 0x0 (800 MHz), vid 0x1e
[ 76.175752] warning: `avahi-daemon' uses 32-bit capabilities (legacy support in use)
[ 76.260037] apm: BIOS not found.
[ 76.373312] ppdev: user-space parallel port driver
[ 79.766222] NET: Registered protocol family 17
[ 82.081519] Bluetooth: L2CAP ver 2.11
[ 82.081536] Bluetooth: L2CAP socket layer initialized
[ 82.100503] Bluetooth: RFCOMM socket layer initialized
[ 82.100552] Bluetooth: RFCOMM TTY layer initialized
[ 82.100558] Bluetooth: RFCOMM ver 1.10
[ 82.148121] Bluetooth: SCO (Voice Link) ver 0.6
[ 82.148141] Bluetooth: SCO socket layer initialized
[ 82.216834] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 82.216856] Bluetooth: BNEP filters: protocol multicast
[ 82.278172] Bridge firewalling registered
[ 82.279149] pan0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
[ 131.326959] CPU0 attaching NULL sched-domain.
[ 131.326977] CPU1 attaching NULL sched-domain.
[ 131.328821] CPU0 attaching sched-domain:
[ 131.328828] domain 0: span 0-1 level CPU
[ 131.328832] groups: 0 1
[ 131.328839] CPU1 attaching sched-domain:
[ 131.328842] domain 0: span 0-1 level CPU
[ 131.328845] groups: 1 0
[55620.706975] usbcore: deregistering interface driver ndiswrapper
[55620.764746] ndiswrapper version 1.53 loaded (smp=yes, preempt=no)
[55620.825079] ndiswrapper (link_pe_images:603): DLL initialize failed for athw.sys
[55620.825911] ndiswrapper: driver netathw (,06/27/2008,7.6.0.239) loaded
[55620.830047] ACPI: PCI Interrupt Link [LK4E] enabled at IRQ 19
[55620.830083] ndiswrapper 0000:03:00.0: PCI INT A -> Link[LK4E] -> GSI 19 (level, low) -> IRQ 19
[55620.830105] ndiswrapper (mp_init:210): assuming WDM (non-NDIS) driver
[55620.840939] usbcore: registered new interface driver ndiswrapper
[55723.661908] NET: Registered protocol family 10
[55723.664562] lo: Disabled Privacy Extensions
[55733.764021] eth0: no IPv6 routers present
6 ) Network configuration
Code:
$ sudo lshw -C network
*-network
description: Ethernet interface
product: MCP67 Ethernet
vendor: nVidia Corporation
physical id: a
bus info: pci@0000:00:0a.0
logical name: eth0
version: a2
serial: 00:1e:68:78:82:a5
size: 100MB/s
capacity: 100MB/s
width: 32 bits
clock: 66MHz
capabilities: pm msi ht bus_master cap_list ethernet physical mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=forcedeth driverversion=0.61 duplex=full ip=192.168.0.195 latency=0 link=yes maxlatency=20 mingnt=1 module=forcedeth multicast=yes port=MII speed=100MB/s
*-network
description: Ethernet controller
product: AR242x 802.11abg Wireless PCI Express Adapter
vendor: Atheros Communications Inc.
physical id: 0
bus info: pci@0000:03:00.0
version: 01
width: 64 bits
clock: 33MHz
capabilities: pm msi pciexpress msix bus_master cap_list
configuration: driver=ndiswrapper latency=0 module=ndiswrapper
*-network DISABLED
description: Ethernet interface
physical id: 1
logical name: pan0
serial: 96:a8:1d:c8:21:00
capabilities: ethernet physical
configuration: broadcast=yes driver=bridge driverversion=2.3 firmware=N/A link=yes multicast=yes
7 ) Scan for networks:
Code:
$ iwlist scan
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
pan0 Interface doesn't support scanning.
8 ) Ubuntu Version:
Code:
$ lsb_release -d
Description: Ubuntu 8.10
9 ) Kernel/architecture (including 32 vs. 64 bit):
Code:
$ uname -mr
2.6.27-7-generic i686
10 ) Restarting the network:
Code:
$ sudo /etc/init.d/networking restart
* Reconfiguring network interfaces... [ OK ]
1 ) Machine Brand and Model (PC/Laptop):
Code: HP Pavilion 9700 laptop (label also calls it a dv9910)
2 ) Wireless Brand, Model and Wireless Chipset:
Code: $ lspci -nn | grep 'Wireless Brand'
03:00.0 Ethernet controller [0200]: Atheros Communications Inc. AR242x 802.11abg Wireless PCI Express Adapter [168c:001c] (rev 01)
3 ) check interface:
Code:
$ ifconfig
eth0 Link encap:Ethernet HWaddr 00:1e:68:78:82:a5
inet addr:192.168.0.195 Bcast:192.168.0.255 Mask:255.255.255.0
inet6 addr: fe80::21e:68ff:fe78:82a5/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:12164 errors:0 dropped:0 overruns:0 frame:0
TX packets:4775 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:10851030 (10.8 MB) TX bytes:571411 (571.4 KB)
Interrupt:220 Base address:0x2000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:82 errors:0 dropped:0 overruns:0 frame:0
TX packets:82 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:4100 (4.1 KB) TX bytes:4100 (4.1 KB)
$ iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
pan0 no wireless extensions.
(hint) if the Wireless interface name is wlan0 you can also use
Code:
$ iwconfig wlan0
4 ) Check for modules:
Code:
$ lsmod
Module Size Used by
ipv6 263972 10
ndiswrapper 196380 0
bridge 56980 0
stp 10628 1 bridge
bnep 20480 2
sco 18308 2
rfcomm 44432 2
l2cap 30464 16 bnep,rfcomm
af_packet 25728 2
ppdev 15620 0
powernow_k8 22148 1
cpufreq_conservative 14600 0
cpufreq_ondemand 14988 1
cpufreq_userspace 11396 0
cpufreq_stats 13188 0
freq_table 12672 3 powernow_k8,cpufreq_ondemand,cpufreq_stats
cpufreq_powersave 9856 0
pci_slot 12552 0
container 11520 0
sbs 19464 0
sbshc 13440 1 sbs
iptable_filter 10752 0
ip_tables 19600 1 iptable_filter
x_tables 22916 1 ip_tables
sbp2 29324 0
parport_pc 39204 0
lp 17156 0
parport 42604 3 ppdev,parport_pc,lp
joydev 18368 0
serio_raw 13444 0
nvidia 7103300 36
agpgart 42184 1 nvidia
pcspkr 10624 0
psmouse 45200 0
k8temp 12416 0
uvcvideo 62728 0
shpchp 37908 0
pci_hotplug 35236 1 shpchp
i2c_core 31892 1 nvidia
compat_ioctl32 9344 1 uvcvideo
videodev 41344 1 uvcvideo
v4l1_compat 22404 2 uvcvideo,videodev
evdev 17696 12
btusb 19736 3
bluetooth 61924 11 bnep,sco,rfcomm,l2cap,btusb
sdhci_pci 15360 0
sdhci 23940 1 sdhci_pci
mmc_core 58268 1 sdhci
video 25104 5
ricoh_mmc 11904 0
output 11008 1 video
snd_hda_intel 381488 2
snd_pcm_oss 46848 0
snd_mixer_oss 22784 1 snd_pcm_oss
snd_pcm 83204 2 snd_hda_intel,snd_pcm_oss
snd_seq_dummy 10884 0
snd_seq_oss 38528 0
snd_seq_midi 14336 0
snd_rawmidi 29824 1 snd_seq_midi
snd_seq_midi_event 15232 2 snd_seq_oss,snd_seq_midi
wmi 14504 0
battery 18436 0
snd_seq 57776 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_mid i_event
snd_timer 29960 2 snd_pcm,snd_seq
snd_seq_device 15116 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi ,snd_seq
snd 63268 13 snd_hda_intel,snd_pcm_oss,snd_mixer_oss,snd_pcm,sn d_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_de vice
button 14224 0
ac 12292 0
soundcore 15328 1 snd
snd_page_alloc 16136 2 snd_hda_intel,snd_pcm
ext3 133384 1
jbd 55444 1 ext3
mbcache 16004 1 ext3
sd_mod 42264 3
crc_t10dif 9984 1 sd_mod
usbhid 35840 0
hid 50560 1 usbhid
sr_mod 22212 0
cdrom 43168 1 sr_mod
sg 39732 0
pata_acpi 12160 0
ata_generic 12932 0
pata_amd 18692 0
ahci 37132 2
ohci1394 37936 0
forcedeth 61328 0
ohci_hcd 31888 0
libata 177312 4 pata_acpi,ata_generic,pata_amd,ahci
scsi_mod 155212 5 sbp2,sd_mod,sr_mod,sg,libata
ehci_hcd 43276 0
ieee1394 96324 2 sbp2,ohci1394
usbcore 148848 7 ndiswrapper,uvcvideo,btusb,usbhid,ohci_hcd,ehci_hc d
dock 16656 1 libata
thermal 23708 0
processor 42156 4 powernow_k8,thermal
fan 12548 0
fbcon 47648 0
tileblit 10880 1 fbcon
font 16512 1 fbcon
bitblit 13824 1 fbcon
softcursor 9984 1 bitblit
fuse 60828 3
$ lsmod | grep "wlan_module_name"
5 ) Kernel boot messages
Code:
$ dmesg
[ 0.516692] PCI: 0000:00:09.0 reg 14 io port: [30e4, 30e7]
[ 0.516696] PCI: 0000:00:09.0 reg 18 io port: [30e8, 30ef]
[ 0.516700] PCI: 0000:00:09.0 reg 1c io port: [30e0, 30e3]
[ 0.516704] PCI: 0000:00:09.0 reg 20 io port: [30d0, 30df]
[ 0.516708] PCI: 0000:00:09.0 reg 24 32bit mmio: [f6484000, f6485fff]
[ 0.516748] PCI: 0000:00:0a.0 reg 10 32bit mmio: [f6488000, f6488fff]
[ 0.516752] PCI: 0000:00:0a.0 reg 14 io port: [30f8, 30ff]
[ 0.516756] PCI: 0000:00:0a.0 reg 18 32bit mmio: [f6489c00, f6489cff]
[ 0.516761] PCI: 0000:00:0a.0 reg 1c 32bit mmio: [f6489800, f648980f]
[ 0.516779] pci 0000:00:0a.0: supports D1
[ 0.516780] pci 0000:00:0a.0: supports D2
[ 0.516782] pci 0000:00:0a.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.516787] pci 0000:00:0a.0: PME# disabled
[ 0.516816] pci 0000:00:0c.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.516819] pci 0000:00:0c.0: PME# disabled
[ 0.516845] pci 0000:00:0d.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.516848] pci 0000:00:0d.0: PME# disabled
[ 0.516866] PCI: 0000:00:12.0 reg 10 32bit mmio: [f5000000, f5ffffff]
[ 0.516870] PCI: 0000:00:12.0 reg 14 32bit mmio: [d0000000, dfffffff]
[ 0.516877] PCI: 0000:00:12.0 reg 1c 64bit mmio: [f4000000, f4ffffff]
[ 0.516883] PCI: 0000:00:12.0 reg 30 32bit mmio: [0, 1ffff]
[ 0.516986] PCI: 0000:02:05.0 reg 10 32bit mmio: [0, 7ff]
[ 0.517017] pci 0000:02:05.0: supports D1
[ 0.517019] pci 0000:02:05.0: supports D2
[ 0.517021] pci 0000:02:05.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.517025] pci 0000:02:05.0: PME# disabled
[ 0.517046] PCI: 0000:02:05.1 reg 10 32bit mmio: [f6100800, f61008ff]
[ 0.517077] pci 0000:02:05.1: supports D1
[ 0.517078] pci 0000:02:05.1: supports D2
[ 0.517080] pci 0000:02:05.1: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.517084] pci 0000:02:05.1: PME# disabled
[ 0.517105] PCI: 0000:02:05.2 reg 10 32bit mmio: [f6100c00, f6100cff]
[ 0.517136] pci 0000:02:05.2: supports D1
[ 0.517137] pci 0000:02:05.2: supports D2
[ 0.517140] pci 0000:02:05.2: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.517144] pci 0000:02:05.2: PME# disabled
[ 0.517164] PCI: 0000:02:05.3 reg 10 32bit mmio: [f6101000, f61010ff]
[ 0.517195] pci 0000:02:05.3: supports D1
[ 0.517197] pci 0000:02:05.3: supports D2
[ 0.517199] pci 0000:02:05.3: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.517203] pci 0000:02:05.3: PME# disabled
[ 0.517225] PCI: 0000:02:05.4 reg 10 32bit mmio: [f6101400, f61014ff]
[ 0.517256] pci 0000:02:05.4: supports D1
[ 0.517258] pci 0000:02:05.4: supports D2
[ 0.517260] pci 0000:02:05.4: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.517264] pci 0000:02:05.4: PME# disabled
[ 0.517293] pci 0000:00:08.0: transparent bridge
[ 0.517298] PCI: bridge 0000:00:08.0 32bit mmio: [f6100000, f61fffff]
[ 0.517337] PCI: bridge 0000:00:0c.0 io port: [4000, 4fff]
[ 0.517340] PCI: bridge 0000:00:0c.0 32bit mmio: [f2000000, f3ffffff]
[ 0.517344] PCI: bridge 0000:00:0c.0 64bit mmio pref: [f0000000, f1ffffff]
[ 0.517379] PCI: 0000:03:00.0 reg 10 64bit mmio: [f6000000, f600ffff]
[ 0.517449] PCI: bridge 0000:00:0d.0 32bit mmio: [f6000000, f60fffff]
[ 0.517459] bus 00 -> node 0
[ 0.517466] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.517575] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P0._PRT]
[ 0.517600] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR1._PRT]
[ 0.517640] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR2._PRT]
[ 0.557911] ACPI: PCI Interrupt Link [LNK1] (IRQs 5) *10
[ 0.557911] ACPI: PCI Interrupt Link [LNK2] (IRQs 7) *11
[ 0.557911] ACPI: PCI Interrupt Link [LNK3] (IRQs 10) *0, disabled.
[ 0.557911] ACPI: PCI Interrupt Link [LNK4] (IRQs 11) *0, disabled.
[ 0.557911] ACPI: PCI Interrupt Link [LK1E] (IRQs 16) *0, disabled.
[ 0.557911] ACPI: PCI Interrupt Link [LK2E] (IRQs 17) *0, disabled.
[ 0.557911] ACPI: PCI Interrupt Link [LK3E] (IRQs 18) *0, disabled.
[ 0.558139] ACPI: PCI Interrupt Link [LK4E] (IRQs 19) *10
[ 0.558405] ACPI: PCI Interrupt Link [LSMB] (IRQs *10)
[ 0.558671] ACPI: PCI Interrupt Link [LUS0] (IRQs 18) *11
[ 0.558938] ACPI: PCI Interrupt Link [LUS2] (IRQs 22) *7
[ 0.559210] ACPI: PCI Interrupt Link [LMAC] (IRQs 20) *11
[ 0.559478] ACPI: PCI Interrupt Link [LAZA] (IRQs 21) *10
[ 0.559745] ACPI: PCI Interrupt Link [LGPU] (IRQs 16) *10
[ 0.560021] ACPI: PCI Interrupt Link [LPID] (IRQs 22) *0, disabled.
[ 0.560299] ACPI: PCI Interrupt Link [LSI0] (IRQs 23) *11
[ 0.560567] ACPI: PCI Interrupt Link [Z018] (IRQs 18) *5
[ 0.560838] ACPI: PCI Interrupt Link [Z019] (IRQs 22) *10
[ 0.561110] ACPI: PCI Interrupt Link [LPMU] (IRQs *11)
[ 0.564161] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 0.564183] pnp: PnP ACPI init
[ 0.564183] ACPI: bus type pnp registered
[ 0.569276] pnp: PnP ACPI: found 12 devices
[ 0.569276] ACPI: ACPI bus type pnp unregistered
[ 0.569276] PnPBIOS: Disabled by ACPI PNP
[ 0.569276] PCI: Using ACPI for IRQ routing
[ 0.572045] NET: Registered protocol family 8
[ 0.572047] NET: Registered protocol family 20
[ 0.576040] NetLabel: Initializing
[ 0.576040] NetLabel: domain hash size = 128
[ 0.576040] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.576055] NetLabel: unlabeled traffic allowed by default
[ 0.576064] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 31
[ 0.576069] hpet0: 3 32-bit timers, 25000000 Hz
[ 0.577648] tracer: 772 pages allocated for 65536 entries of 48 bytes
[ 0.577651] actual entries 65620
[ 0.577797] AppArmor: AppArmor Filesystem Enabled
[ 0.577825] ACPI: RTC can wake from S4
[ 0.580051] Switched to high resolution mode on CPU 0
[ 0.580065] Switched to high resolution mode on CPU 1
[ 0.580095] system 00:02: iomem range 0xe0000000-0xefffffff could not be reserved
[ 0.580102] system 00:03: ioport range 0x1000-0x107f has been reserved
[ 0.580106] system 00:03: ioport range 0x1080-0x10ff has been reserved
[ 0.580109] system 00:03: ioport range 0x1400-0x147f has been reserved
[ 0.580112] system 00:03: ioport range 0x1480-0x14ff has been reserved
[ 0.580115] system 00:03: ioport range 0x1800-0x187f has been reserved
[ 0.580118] system 00:03: ioport range 0x1880-0x18ff has been reserved
[ 0.580125] system 00:04: ioport range 0x360-0x361 has been reserved
[ 0.580128] system 00:04: ioport range 0x4d0-0x4d1 has been reserved
[ 0.580139] system 00:0b: iomem range 0xffc00000-0xffffffff could not be reserved
[ 0.580143] system 00:0b: iomem range 0xfec00000-0xfec00fff could not be reserved
[ 0.580146] system 00:0b: iomem range 0xfee00000-0xfeefffff could not be reserved
[ 0.580150] system 00:0b: iomem range 0xfed00000-0xfed00fff has been reserved
[ 0.580153] system 00:0b: iomem range 0xfef00000-0xfef00fff has been reserved
[ 0.615468] pci 0000:00:08.0: PCI bridge, secondary bus 0000:02
[ 0.615471] pci 0000:00:08.0: IO window: disabled
[ 0.615475] pci 0000:00:08.0: MEM window: 0xf6100000-0xf61fffff
[ 0.615478] pci 0000:00:08.0: PREFETCH window: disabled
[ 0.615483] pci 0000:00:0c.0: PCI bridge, secondary bus 0000:04
[ 0.615486] pci 0000:00:0c.0: IO window: 0x4000-0x4fff
[ 0.615489] pci 0000:00:0c.0: MEM window: 0xf2000000-0xf3ffffff
[ 0.615493] pci 0000:00:0c.0: PREFETCH window: 0x000000f0000000-0x000000f1ffffff
[ 0.615497] pci 0000:00:0d.0: PCI bridge, secondary bus 0000:03
[ 0.615499] pci 0000:00:0d.0: IO window: disabled
[ 0.615503] pci 0000:00:0d.0: MEM window: 0xf6000000-0xf60fffff
[ 0.615506] pci 0000:00:0d.0: PREFETCH window: disabled
[ 0.615516] pci 0000:00:08.0: setting latency timer to 64
[ 0.615521] pci 0000:00:0c.0: setting latency timer to 64
[ 0.615526] pci 0000:00:0d.0: setting latency timer to 64
[ 0.615530] bus: 00 index 0 io port: [0, ffff]
[ 0.615532] bus: 00 index 1 mmio: [0, ffffffff]
[ 0.615534] bus: 02 index 0 mmio: [0, 0]
[ 0.615536] bus: 02 index 1 mmio: [f6100000, f61fffff]
[ 0.615539] bus: 02 index 2 mmio: [0, 0]
[ 0.615541] bus: 02 index 3 io port: [0, ffff]
[ 0.615543] bus: 02 index 4 mmio: [0, ffffffff]
[ 0.615545] bus: 04 index 0 io port: [4000, 4fff]
[ 0.615548] bus: 04 index 1 mmio: [f2000000, f3ffffff]
[ 0.615550] bus: 04 index 2 mmio: [f0000000, f1ffffff]
[ 0.615553] bus: 04 index 3 mmio: [0, 0]
[ 0.615555] bus: 03 index 0 mmio: [0, 0]
[ 0.615557] bus: 03 index 1 mmio: [f6000000, f60fffff]
[ 0.615559] bus: 03 index 2 mmio: [0, 0]
[ 0.615561] bus: 03 index 3 mmio: [0, 0]
[ 0.615574] NET: Registered protocol family 2
[ 0.625077] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.625380] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.626181] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.626632] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.626636] TCP reno registered
[ 0.629120] NET: Registered protocol family 1
[ 0.629249] checking if image is initramfs... it is
[ 1.322651] Freeing initrd memory: 7932k freed
[ 1.322824] Simple Boot Flag at 0x36 set to 0x1
[ 1.324095] audit: initializing netlink socket (disabled)
[ 1.324111] type=2000 audit(1226798723.324:1): initialized
[ 1.330205] highmem bounce pool size: 64 pages
[ 1.330211] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 1.333130] VFS: Disk quotas dquot_6.5.1
[ 1.333232] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.333364] msgmni has been set to 1726
[ 1.333495] io scheduler noop registered
[ 1.333497] io scheduler anticipatory registered
[ 1.333500] io scheduler deadline registered
[ 1.333512] io scheduler cfq registered (default)
[ 1.333545] pci 0000:00:00.0: Enabling HT MSI Mapping
[ 1.333705] pci 0000:00:07.0: Enabling HT MSI Mapping
[ 1.333721] pci 0000:00:08.0: Enabling HT MSI Mapping
[ 1.333737] pci 0000:00:09.0: Enabling HT MSI Mapping
[ 1.333754] pci 0000:00:0a.0: Enabling HT MSI Mapping
[ 1.333769] pci 0000:00:0c.0: Enabling HT MSI Mapping
[ 1.333785] pci 0000:00:0d.0: Enabling HT MSI Mapping
[ 1.333800] pci 0000:00:12.0: Boot video device
[ 1.333940] pcieport-driver 0000:00:0c.0: setting latency timer to 64
[ 1.333965] pcieport-driver 0000:00:0c.0: found MSI capability
[ 1.333987] pci_express 0000:00:0c.0:pcie00: allocate port service
[ 1.334045] pci_express 0000:00:0c.0:pcie03: allocate port service
[ 1.334133] pcieport-driver 0000:00:0d.0: setting latency timer to 64
[ 1.334159] pcieport-driver 0000:00:0d.0: found MSI capability
[ 1.334177] pci_express 0000:00:0d.0:pcie00: allocate port service
[ 1.334231] pci_express 0000:00:0d.0:pcie03: allocate port service
[ 1.334636] isapnp: Scanning for PnP cards...
[ 1.687211] isapnp: No Plug & Play device found
[ 1.730977] hpet_resources: 0xfed00000 is busy
[ 1.731088] Serial: 8250/16550 driver4 ports, IRQ sharing enabled
[ 1.733837] brd: module loaded
[ 1.733921] input: Macintosh mouse button emulation as /devices/virtual/input/input0
[ 1.734064] PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12
[ 1.762783] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.762790] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.763178] mice: PS/2 mouse device common for all mice
[ 1.763330] rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0
[ 1.763364] rtc0: alarms up to one year, y3k, hpet irqs
[ 1.763502] EISA: Probing bus 0 at eisa.0
[ 1.763508] Cannot allocate resource for EISA slot 1
[ 1.763513] Cannot allocate resource for EISA slot 3
[ 1.763516] Cannot allocate resource for EISA slot 4
[ 1.763530] EISA: Detected 0 cards.
[ 1.763534] cpuidle: using governor ladder
[ 1.763537] cpuidle: using governor menu
[ 1.764034] TCP cubic registered
[ 1.764062] Using IPI No-Shortcut mode
[ 1.764280] registered taskstats version 1
[ 1.764421] Magic number: 0:709:407
[ 1.764577] acpi PNP0800:00: hash matches
[ 1.764589] acpi ACPI0003:00: hash matches
[ 1.764635] rtc_cmos 00:07: setting system clock to 2008-11-16 01:25:24 UTC (1226798724)
[ 1.764638] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 1.764641] EDD information not available.
[ 1.764953] Freeing unused kernel memory: 424k freed
[ 1.765039] Write protecting the kernel text: 2576k
[ 1.765080] Write protecting the kernel read-only data: 936k
[ 1.784619] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
[ 1.900407] fuse init (API version 7.9)
[ 2.026738] ACPI: processor limited to max C-state 1
[ 2.026931] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[ 2.027021] processor ACPI0007:00: registered as cooling_device0
[ 2.027027] ACPI: Processor [CPU0] (supports 8 throttling states)
[ 2.027245] ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
[ 2.027319] processor ACPI0007:01: registered as cooling_device1
[ 2.027324] ACPI: Processor [CPU1] (supports 8 throttling states)
[ 2.030097] ACPI Exception (thermal-0377): AE_OK, No or invalid critical threshold [20080609]
[ 2.504261] No dock devices found.
[ 2.542304] usbcore: registered new interface driver usbfs
[ 2.542327] usbcore: registered new interface driver hub
[ 2.542397] usbcore: registered new device driver usb
[ 2.545603] ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 22
[ 2.545616] ehci_hcd 0000:00:02.1: PCI INT B -> Link[LUS2] -> GSI 22 (level, low) -> IRQ 22
[ 2.545628] ehci_hcd 0000:00:02.1: setting latency timer to 64
[ 2.545631] ehci_hcd 0000:00:02.1: EHCI Host Controller
[ 2.545681] ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1
[ 2.545710] ehci_hcd 0000:00:02.1: debug port 1
[ 2.545715] ehci_hcd 0000:00:02.1: cache line size of 64 is not supported
[ 2.545731] ehci_hcd 0000:00:02.1: irq 22, io mem 0xf6489000
[ 2.559461] ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 2.559624] usb usb1: configuration #1 chosen from 1 choice
[ 2.559657] hub 1-0:1.0: USB hub found
[ 2.559667] hub 1-0:1.0: 7 ports detected
[ 2.560227] SCSI subsystem initialized
[ 2.579472] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.579614] libata version 3.00 loaded.
[ 2.765893] ACPI: PCI Interrupt Link [Z019] enabled at IRQ 22
[ 2.765901] ehci_hcd 0000:00:04.1: PCI INT B -> Link[Z019] -> GSI 22 (level, low) -> IRQ 22
[ 2.765917] ehci_hcd 0000:00:04.1: setting latency timer to 64
[ 2.765920] ehci_hcd 0000:00:04.1: EHCI Host Controller
[ 2.765947] ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 2
[ 2.765976] ehci_hcd 0000:00:04.1: debug port 1
[ 2.765981] ehci_hcd 0000:00:04.1: cache line size of 64 is not supported
[ 2.765989] ehci_hcd 0000:00:04.1: irq 22, io mem 0xf6489400
[ 2.777030] ehci_hcd 0000:00:04.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 2.777219] usb usb2: configuration #1 chosen from 1 choice
[ 2.777247] hub 2-0:1.0: USB hub found
[ 2.777257] hub 2-0:1.0: 2 ports detected
[ 8.188951] ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 18
[ 8.188964] ohci_hcd 0000:00:02.0: PCI INT A -> Link[LUS0] -> GSI 18 (level, low) -> IRQ 18
[ 8.188979] ohci_hcd 0000:00:02.0: setting latency timer to 64
[ 8.188982] ohci_hcd 0000:00:02.0: OHCI Host Controller
[ 8.189012] Clocksource tsc unstable (delta = 4398044243638 ns)
[ 8.189031] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 3
[ 8.189055] ohci_hcd 0000:00:02.0: irq 18, io mem 0xf6486000
[ 8.432377] usb usb3: configuration #1 chosen from 1 choice
[ 8.432407] hub 3-0:1.0: USB hub found
[ 8.432418] hub 3-0:1.0: 7 ports detected
[ 8.616378] usb 2-2: new high speed USB device using ehci_hcd and address 3
[ 8.663985] ACPI: PCI Interrupt Link [Z018] enabled at IRQ 18
[ 8.663991] ohci_hcd 0000:00:04.0: PCI INT A -> Link[Z018] -> GSI 18 (level, low) -> IRQ 18
[ 8.664006] ohci_hcd 0000:00:04.0: setting latency timer to 64
[ 8.664009] ohci_hcd 0000:00:04.0: OHCI Host Controller
[ 8.664039] ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 4
[ 8.664053] ohci_hcd 0000:00:04.0: irq 18, io mem 0xf6487000
[ 8.743512] usb usb4: configuration #1 chosen from 1 choice
[ 8.743541] hub 4-0:1.0: USB hub found
[ 8.743552] hub 4-0:1.0: 2 ports detected
[ 8.871849] usb 2-2: configuration #1 chosen from 1 choice
[ 8.961117] pata_amd 0000:00:06.0: version 0.3.10
[ 8.961165] pata_amd 0000:00:06.0: setting latency timer to 64
[ 8.961590] scsi0 : pata_amd
[ 8.961981] scsi1 : pata_amd
[ 8.962392] ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0x30c0 irq 14
[ 8.962396] ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x30c8 irq 15
[ 9.053828] usb 3-5: new low speed USB device using ohci_hcd and address 2
[ 9.148076] ata1.00: ATAPI: PIONEER DVDRW DR-KD08HB, 1K09, max MWDMA2
[ 9.148090] ata1: nv_mode_filter: 0x39f&0x39f->0x39f, BIOS=0x0 (0xc600) ACPI=0x39f (120:600:0x12)
[ 9.210577] ata1.00: configured for MWDMA2
[ 9.210619] ata2: port disabled. ignoring.
[ 9.249308] scsi 0:0:0:0: CD-ROM PIONEER DVDRW DR-KD08HB 1K09 PQ: 0 ANSI: 5
[ 9.249497] ahci 0000:00:09.0: version 3.0
[ 9.249918] ACPI: PCI Interrupt Link [LSI0] enabled at IRQ 23
[ 9.249929] ahci 0000:00:09.0: PCI INT A -> Link[LSI0] -> GSI 23 (level, low) -> IRQ 23
[ 9.250019] ahci 0000:00:09.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl IDE mode
[ 9.250024] ahci 0000:00:09.0: flags: 64bit sntf led clo pmp pio slum part
[ 9.250027] ahci 0000:00:09.0: setting latency timer to 64
[ 9.251038] scsi2 : ahci
[ 9.251496] scsi3 : ahci
[ 9.251952] scsi4 : ahci
[ 9.253126] scsi5 : ahci
[ 9.253242] ata3: SATA max UDMA/133 abar m8192@0xf6484000 port 0xf6484100 irq 221
[ 9.253245] ata4: SATA max UDMA/133 abar m8192@0xf6484000 port 0xf6484180 irq 221
[ 9.253248] ata5: SATA max UDMA/133 abar m8192@0xf6484000 port 0xf6484200 irq 221
[ 9.253252] ata6: SATA max UDMA/133 abar m8192@0xf6484000 port 0xf6484280 irq 221
[ 9.291704] usb 3-5: configuration #1 chosen from 1 choice
[ 9.491949] usb 4-1: new full speed USB device using ohci_hcd and address 2
[ 9.776574] usb 4-1: configuration #1 chosen from 1 choice
[ 9.804218] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 9.804635] ata3.00: ATA-8: TOSHIBA MK2552GSX, LV012C, max UDMA/100
[ 9.804638] ata3.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 9.805128] ata3.00: configured for UDMA/100
[ 10.179628] ata4: SATA link down (SStatus 0 SControl 300)
[ 10.554500] ata5: SATA link down (SStatus 0 SControl 300)
[ 10.930645] ata6: SATA link down (SStatus 0 SControl 300)
[ 10.930754] scsi 2:0:0:0: Direct-Access ATA TOSHIBA MK2552GS LV01 PQ: 0 ANSI: 5
[ 10.930861] forcedeth: Reverse Engineered nForce ethernet driver. Version 0.61.
[ 10.931297] ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 20
[ 10.931308] forcedeth 0000:00:0a.0: PCI INT A -> Link[LMAC] -> GSI 20 (level, low) -> IRQ 20
[ 10.931313] forcedeth 0000:00:0a.0: setting latency timer to 64
[ 11.493107] forcedeth 0000:00:0a.0: ifname eth0, PHY OUI 0x732 @ 1, addr 00:1e:68:78:82:a5
[ 11.493111] forcedeth 0000:00:0a.0: highdma pwrctl mgmt timirq lnktim msi desc-v3
[ 11.494949] ohci1394 0000:02:05.0: enabling device (0100 -> 0102)
[ 11.495376] ACPI: PCI Interrupt Link [LNK1] enabled at IRQ 5
[ 11.495389] ohci1394 0000:02:05.0: PCI INT A -> Link[LNK1] -> GSI 5 (level, low) -> IRQ 5
[ 11.547123] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[5] MMIO=[f6100000-f61007ff] Max Packet=[2048] IR/IT contexts=[4/4]
[ 11.593228] scsi 0:0:0:0: Attached scsi generic sg0 type 5
[ 11.594230] scsi 2:0:0:0: Attached scsi generic sg1 type 0
[ 11.615666] Driver 'sr' needs updating - please use bus_type methods
[ 11.626710] usbcore: registered new interface driver hiddev
[ 11.632231] Driver 'sd' needs updating - please use bus_type methods
[ 11.636694] input: Razer Razer Diamondback Optical Mouse as /devices/pci0000:00/0000:00:02.0/usb3/3-5/3-5:1.0/input/input2
[ 11.654718] input,hidraw0: USB HID v1.10 Mouse [Razer Razer Diamondback Optical Mouse] on usb-0000:00:02.0-5
[ 11.654746] usbcore: registered new interface driver usbhid
[ 11.654750] usbhid: v2.6:USB HID core driver
[ 11.743384] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[ 11.743390] Uniform CD-ROM driver Revision: 3.20
[ 11.743493] sr 0:0:0:0: Attached scsi CD-ROM sr0
[ 11.743619] sd 2:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB)
[ 11.743640] sd 2:0:0:0: [sda] Write Protect is off
[ 11.743643] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 11.743679] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 11.743750] sd 2:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB)
[ 11.743767] sd 2:0:0:0: [sda] Write Protect is off
[ 11.743770] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 11.743802] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 11.743806] sda: sda1 sda2 sda3 < sda5 sda6 >
[ 11.870576] sd 2:0:0:0: [sda] Attached SCSI disk
[ 13.740127] PM: Starting manual resume from disk
[ 13.740131] PM: Resume from partition 8:6
[ 13.740133] PM: Checking hibernation image.
[ 13.740268] PM: Resume from disk failed.
[ 13.796622] kjournald starting. Commit interval 5 seconds
[ 13.796648] EXT3-fs: mounted filesystem with ordered data mode.
[ 14.013217] ieee1394: Host added: ID:BUS[0-00:1023] GUID[00241b00311f0001]
[ 25.267244] udevd version 124 started
[ 25.853160] ACPI: AC Adapter [ACAD] (on-line)
[ 25.925195] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[ 25.949035] ACPI: Power Button (FF) [PWRF]
[ 25.949167] input: Sleep Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input4
[ 25.981060] ACPI: Sleep Button (CM) [SLPB]
[ 25.981150] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input5
[ 25.981610] ACPI: Lid Switch [LID]
[ 25.981708] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input6
[ 26.009044] ACPI: Power Button (CM) [PWRB]
[ 26.329541] ACPI: Battery Slot [BAT0] (battery present)
[ 26.329829] ACPI: WMI: Mapper loaded
[ 26.931657] ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 21
[ 26.931671] HDA Intel 0000:00:07.0: PCI INT A -> Link[LAZA] -> GSI 21 (level, low) -> IRQ 21
[ 26.931700] HDA Intel 0000:00:07.0: setting latency timer to 64
[ 26.952170] ricoh-mmc: Ricoh MMC Controller disabling driver
[ 26.952174] ricoh-mmc: Copyright(c) Philip Langdale
[ 26.971601] acpi device:25: registered as cooling_device2
[ 26.971806] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:23/input/input7
[ 26.975085] sdhci: Secure Digital Host Controller Interface driver
[ 26.975089] sdhci: Copyright(c) Pierre Ossman
[ 26.992031] ACPI: Video Device [UVGA] (multi-head: yes rom: no post: no)
[ 26.994523] ricoh-mmc: Ricoh MMC controller found at 0000:02:05.2 [1180:0843] (rev 12)
[ 26.994539] ricoh-mmc: Controller is now disabled.
[ 27.022773] sdhci-pci 0000:02:05.1: SDHCI controller found [1180:0822] (rev 22)
[ 27.023199] ACPI: PCI Interrupt Link [LNK2] enabled at IRQ 7
[ 27.023211] sdhci-pci 0000:02:05.1: PCI INT B -> Link[LNK2] -> GSI 7 (level, low) -> IRQ 7
[ 27.026267] mmc0: SDHCI controller on PCI [0000:02:05.1] using PIO
[ 27.093785] Bluetooth: Core ver 2.13
[ 27.094344] NET: Registered protocol family 31
[ 27.094347] Bluetooth: HCI device and connection manager initialized
[ 27.094351] Bluetooth: HCI socket layer initialized
[ 27.138228] Bluetooth: Generic Bluetooth USB driver ver 0.3
[ 27.138335] usbcore: registered new interface driver btusb
[ 27.378111] Linux video capture interface: v2.00
[ 27.450762] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 27.455928] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 27.502658] uvcvideo: Found UVC 1.00 device HP Webcam (0c45:62c0)
[ 27.506268] input: HP Webcam as /devices/pci0000:00/0000:00:04.1/usb2/2-2/2-2:1.0/input/input8
[ 27.525247] usbcore: registered new interface driver uvcvideo
[ 27.525268] USB Video Class driver (v0.1.0)
[ 27.687141] input: PC Speaker as /devices/platform/pcspkr/input/input9
[ 27.697227] Linux agpgart interface v0.103
[ 27.758966] ndiswrapper version 1.53 loaded (smp=yes, preempt=no)
[ 28.522465] ACPI: PCI Interrupt Link [LGPU] enabled at IRQ 16
[ 28.522480] nvidia 0000:00:12.0: PCI INT A -> Link[LGPU] -> GSI 16 (level, low) -> IRQ 16
[ 28.522487] nvidia 0000:00:12.0: setting latency timer to 64
[ 28.522745] NVRM: loading NVIDIA UNIX x86 Kernel Module 173.14.12 Thu Jul 17 18:11:36 PDT 2008
[ 28.525437] usbcore: registered new interface driver ndiswrapper
[ 28.532540] Synaptics Touchpad, model: 1, fw: 6.3, id: 0x1a0b1, caps: 0xa04711/0xa00000
[ 28.609564] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input10
[ 29.266480] lp: driver loaded but no devices found
[ 29.444744] Adding 2602488k swap on /dev/sda6. Priority:-1 extents:1 across:2602488k
[ 73.198487] EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
[ 73.198673] EXT3 FS on sda5, internal journal
[ 74.252977] type=1505 audit(1226816797.167:2): operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" name2="default" pid=4798
[ 74.456521] type=1505 audit(1226816797.368:3): operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" name2="default" pid=4803
[ 74.456781] type=1505 audit(1226816797.368:4): operation="profile_load" name="/usr/sbin/cupsd" name2="default" pid=4803
[ 74.617254] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 75.422192] powernow-k8: Found 1 AMD Turion(tm) 64 X2 Mobile Technology TL-60 processors (2 cpu cores) (version 2.20.00)
[ 75.422838] powernow-k8: 0 : fid 0xc (2000 MHz), vid 0x11
[ 75.422843] powernow-k8: 1 : fid 0xa (1800 MHz), vid 0x12
[ 75.422845] powernow-k8: 2 : fid 0x8 (1600 MHz), vid 0x13
[ 75.422848] powernow-k8: 3 : fid 0x0 (800 MHz), vid 0x1e
[ 76.175752] warning: `avahi-daemon' uses 32-bit capabilities (legacy support in use)
[ 76.260037] apm: BIOS not found.
[ 76.373312] ppdev: user-space parallel port driver
[ 79.766222] NET: Registered protocol family 17
[ 82.081519] Bluetooth: L2CAP ver 2.11
[ 82.081536] Bluetooth: L2CAP socket layer initialized
[ 82.100503] Bluetooth: RFCOMM socket layer initialized
[ 82.100552] Bluetooth: RFCOMM TTY layer initialized
[ 82.100558] Bluetooth: RFCOMM ver 1.10
[ 82.148121] Bluetooth: SCO (Voice Link) ver 0.6
[ 82.148141] Bluetooth: SCO socket layer initialized
[ 82.216834] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 82.216856] Bluetooth: BNEP filters: protocol multicast
[ 82.278172] Bridge firewalling registered
[ 82.279149] pan0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
[ 131.326959] CPU0 attaching NULL sched-domain.
[ 131.326977] CPU1 attaching NULL sched-domain.
[ 131.328821] CPU0 attaching sched-domain:
[ 131.328828] domain 0: span 0-1 level CPU
[ 131.328832] groups: 0 1
[ 131.328839] CPU1 attaching sched-domain:
[ 131.328842] domain 0: span 0-1 level CPU
[ 131.328845] groups: 1 0
[55620.706975] usbcore: deregistering interface driver ndiswrapper
[55620.764746] ndiswrapper version 1.53 loaded (smp=yes, preempt=no)
[55620.825079] ndiswrapper (link_pe_images:603): DLL initialize failed for athw.sys
[55620.825911] ndiswrapper: driver netathw (,06/27/2008,7.6.0.239) loaded
[55620.830047] ACPI: PCI Interrupt Link [LK4E] enabled at IRQ 19
[55620.830083] ndiswrapper 0000:03:00.0: PCI INT A -> Link[LK4E] -> GSI 19 (level, low) -> IRQ 19
[55620.830105] ndiswrapper (mp_init:210): assuming WDM (non-NDIS) driver
[55620.840939] usbcore: registered new interface driver ndiswrapper
[55723.661908] NET: Registered protocol family 10
[55723.664562] lo: Disabled Privacy Extensions
[55733.764021] eth0: no IPv6 routers present
6 ) Network configuration
Code:
$ sudo lshw -C network
*-network
description: Ethernet interface
product: MCP67 Ethernet
vendor: nVidia Corporation
physical id: a
bus info: pci@0000:00:0a.0
logical name: eth0
version: a2
serial: 00:1e:68:78:82:a5
size: 100MB/s
capacity: 100MB/s
width: 32 bits
clock: 66MHz
capabilities: pm msi ht bus_master cap_list ethernet physical mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=forcedeth driverversion=0.61 duplex=full ip=192.168.0.195 latency=0 link=yes maxlatency=20 mingnt=1 module=forcedeth multicast=yes port=MII speed=100MB/s
*-network
description: Ethernet controller
product: AR242x 802.11abg Wireless PCI Express Adapter
vendor: Atheros Communications Inc.
physical id: 0
bus info: pci@0000:03:00.0
version: 01
width: 64 bits
clock: 33MHz
capabilities: pm msi pciexpress msix bus_master cap_list
configuration: driver=ndiswrapper latency=0 module=ndiswrapper
*-network DISABLED
description: Ethernet interface
physical id: 1
logical name: pan0
serial: 96:a8:1d:c8:21:00
capabilities: ethernet physical
configuration: broadcast=yes driver=bridge driverversion=2.3 firmware=N/A link=yes multicast=yes
7 ) Scan for networks:
Code:
$ iwlist scan
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
pan0 Interface doesn't support scanning.
8 ) Ubuntu Version:
Code:
$ lsb_release -d
Description: Ubuntu 8.10
9 ) Kernel/architecture (including 32 vs. 64 bit):
Code:
$ uname -mr
2.6.27-7-generic i686
10 ) Restarting the network:
Code:
$ sudo /etc/init.d/networking restart
* Reconfiguring network interfaces... [ OK ]