excogitation
September 10th, 2008, 12:08 AM
The harddrive is encrypted (whole disk) using Truecrypt.
It's in a SATA/USB <-> PATA & SATA housing and I connect it with USB to my laptop.
# lsusb
Bus 005 Device 005: ID 152d:2338 JMicron Technology Corp. / JMicron USA Technology Corp. JM20337 Hi-Speed USB to SATA & PATA Combo Bridge
# fdisk -l
Disk /dev/sdb: 80.0 GB, 80026361856 bytes
255 heads, 63 sectors/track, 9729 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0xf2e3c1f6
Disk /dev/sdb doesn't contain a valid partition table
After a while just makes those awful clicking noises.
Using it in Windows works just fine (no unexpected noise).
# dmesg
[55072.064065] usb 5-4: new high speed USB device using ehci_hcd and address 4
[55072.228846] usb 5-4: configuration #1 chosen from 1 choice
[55072.267819] scsi3 : SCSI emulation for USB Mass Storage devices
[55072.274405] usb-storage: device found at 4
[55072.274416] usb-storage: waiting for device to settle before scanning
[55077.272472] usb-storage: device scan complete
[55077.275329] scsi 3:0:0:0: Direct-Access ST980815 A D PQ: 0 ANSI: 2 CCS
[55077.319487] sd 3:0:0:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
[55077.323042] sd 3:0:0:0: [sdb] Write Protect is off
[55077.323057] sd 3:0:0:0: [sdb] Mode Sense: 00 38 00 00
[55077.323063] sd 3:0:0:0: [sdb] Assuming drive cache: write through
[55077.331449] sd 3:0:0:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
[55077.334181] sd 3:0:0:0: [sdb] Write Protect is off
[55077.334195] sd 3:0:0:0: [sdb] Mode Sense: 00 38 00 00
[55077.334201] sd 3:0:0:0: [sdb] Assuming drive cache: write through
[55077.335179] sdb:<6>sd 3:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OK
[55089.000496] end_request: I/O error, dev sdb, sector 0
[55089.000510] Buffer I/O error on device sdb, logical block 0
[55089.002304] sd 3:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OK
[55089.002319] end_request: I/O error, dev sdb, sector 0
[55089.002326] Buffer I/O error on device sdb, logical block 0
[55089.005228] sd 3:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OK
[55089.005242] end_request: I/O error, dev sdb, sector 0
[55089.005249] Buffer I/O error on device sdb, logical block 0
[55089.012360] sd 3:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OK
[55089.012379] end_request: I/O error, dev sdb, sector 0
[55089.012388] Buffer I/O error on device sdb, logical block 0
[55089.017457] sd 3:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OK
[55089.017468] end_request: I/O error, dev sdb, sector 0
[55089.017475] Buffer I/O error on device sdb, logical block 0
[55089.017501] ldm_validate_partition_table(): Disk read failed.
[55089.017753] sd 3:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OK
[55089.017762] end_request: I/O error, dev sdb, sector 0
[55089.017769] Buffer I/O error on device sdb, logical block 0
[55089.018120] sd 3:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OK
[55089.018135] end_request: I/O error, dev sdb, sector 0
[55089.018143] Buffer I/O error on device sdb, logical block 0
[55089.018416] sd 3:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OK
[55089.018426] end_request: I/O error, dev sdb, sector 0
[55089.018433] Buffer I/O error on device sdb, logical block 0
[55089.019117] sd 3:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OK
[55089.019127] end_request: I/O error, dev sdb, sector 0
[55089.019134] Buffer I/O error on device sdb, logical block 0
[55089.019158] Dev sdb: unable to read RDB block 0
[55089.019330] sd 3:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OK
[55089.019340] end_request: I/O error, dev sdb, sector 0
[55089.019599] sd 3:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OK
[55089.019609] end_request: I/O error, dev sdb, sector 0
[55089.020248] sd 3:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OK
[55089.020259] end_request: I/O error, dev sdb, sector 24
[55089.021051] sd 3:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OK
[55089.021061] end_request: I/O error, dev sdb, sector 24
[55089.021259] sd 3:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OK
[55089.021269] end_request: I/O error, dev sdb, sector 0
[55089.021462] sd 3:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OK
[55089.021471] end_request: I/O error, dev sdb, sector 0
[55089.021493] unable to read partition table
[55089.026369] sd 3:0:0:0: [sdb] Attached SCSI disk
[55089.026598] sd 3:0:0:0: Attached scsi generic sg2 type 0
[55089.073268] usb 5-4: USB disconnect, address 4
[55101.344414] ACPI: \_SB_.PCI0.SATA.SECD.BAY_: found ejectable bay
[55101.344427] ACPI: \_SB_.PCI0.SATA.SECD.BAY_: Adding notify handler
[55101.346551] ACPI: Error installing bay notify handler
[55126.784051] usb 5-4: new high speed USB device using ehci_hcd and address 5
[55126.971125] usb 5-4: configuration #1 chosen from 1 choice
[55126.999189] scsi4 : SCSI emulation for USB Mass Storage devices
[55127.003346] usb-storage: device found at 5
[55127.003358] usb-storage: waiting for device to settle before scanning
[55132.000389] usb-storage: device scan complete
[55132.001998] scsi 4:0:0:0: Direct-Access ST980815 A D PQ: 0 ANSI: 2 CCS
[55132.054898] sd 4:0:0:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
[55132.057217] sd 4:0:0:0: [sdb] Write Protect is off
[55132.057230] sd 4:0:0:0: [sdb] Mode Sense: 00 38 00 00
[55132.057251] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[55132.060750] sd 4:0:0:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
[55132.062765] sd 4:0:0:0: [sdb] Write Protect is off
[55132.062777] sd 4:0:0:0: [sdb] Mode Sense: 00 38 00 00
[55132.062783] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[55132.067669] sdb: unknown partition table
[55132.087338] sd 4:0:0:0: [sdb] Attached SCSI disk
[55132.088320] sd 4:0:0:0: Attached scsi generic sg2 type 0
[55155.204177] usb 5-4: USB disconnect, address 5
It's in a SATA/USB <-> PATA & SATA housing and I connect it with USB to my laptop.
# lsusb
Bus 005 Device 005: ID 152d:2338 JMicron Technology Corp. / JMicron USA Technology Corp. JM20337 Hi-Speed USB to SATA & PATA Combo Bridge
# fdisk -l
Disk /dev/sdb: 80.0 GB, 80026361856 bytes
255 heads, 63 sectors/track, 9729 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0xf2e3c1f6
Disk /dev/sdb doesn't contain a valid partition table
After a while just makes those awful clicking noises.
Using it in Windows works just fine (no unexpected noise).
# dmesg
[55072.064065] usb 5-4: new high speed USB device using ehci_hcd and address 4
[55072.228846] usb 5-4: configuration #1 chosen from 1 choice
[55072.267819] scsi3 : SCSI emulation for USB Mass Storage devices
[55072.274405] usb-storage: device found at 4
[55072.274416] usb-storage: waiting for device to settle before scanning
[55077.272472] usb-storage: device scan complete
[55077.275329] scsi 3:0:0:0: Direct-Access ST980815 A D PQ: 0 ANSI: 2 CCS
[55077.319487] sd 3:0:0:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
[55077.323042] sd 3:0:0:0: [sdb] Write Protect is off
[55077.323057] sd 3:0:0:0: [sdb] Mode Sense: 00 38 00 00
[55077.323063] sd 3:0:0:0: [sdb] Assuming drive cache: write through
[55077.331449] sd 3:0:0:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
[55077.334181] sd 3:0:0:0: [sdb] Write Protect is off
[55077.334195] sd 3:0:0:0: [sdb] Mode Sense: 00 38 00 00
[55077.334201] sd 3:0:0:0: [sdb] Assuming drive cache: write through
[55077.335179] sdb:<6>sd 3:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OK
[55089.000496] end_request: I/O error, dev sdb, sector 0
[55089.000510] Buffer I/O error on device sdb, logical block 0
[55089.002304] sd 3:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OK
[55089.002319] end_request: I/O error, dev sdb, sector 0
[55089.002326] Buffer I/O error on device sdb, logical block 0
[55089.005228] sd 3:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OK
[55089.005242] end_request: I/O error, dev sdb, sector 0
[55089.005249] Buffer I/O error on device sdb, logical block 0
[55089.012360] sd 3:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OK
[55089.012379] end_request: I/O error, dev sdb, sector 0
[55089.012388] Buffer I/O error on device sdb, logical block 0
[55089.017457] sd 3:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OK
[55089.017468] end_request: I/O error, dev sdb, sector 0
[55089.017475] Buffer I/O error on device sdb, logical block 0
[55089.017501] ldm_validate_partition_table(): Disk read failed.
[55089.017753] sd 3:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OK
[55089.017762] end_request: I/O error, dev sdb, sector 0
[55089.017769] Buffer I/O error on device sdb, logical block 0
[55089.018120] sd 3:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OK
[55089.018135] end_request: I/O error, dev sdb, sector 0
[55089.018143] Buffer I/O error on device sdb, logical block 0
[55089.018416] sd 3:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OK
[55089.018426] end_request: I/O error, dev sdb, sector 0
[55089.018433] Buffer I/O error on device sdb, logical block 0
[55089.019117] sd 3:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OK
[55089.019127] end_request: I/O error, dev sdb, sector 0
[55089.019134] Buffer I/O error on device sdb, logical block 0
[55089.019158] Dev sdb: unable to read RDB block 0
[55089.019330] sd 3:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OK
[55089.019340] end_request: I/O error, dev sdb, sector 0
[55089.019599] sd 3:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OK
[55089.019609] end_request: I/O error, dev sdb, sector 0
[55089.020248] sd 3:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OK
[55089.020259] end_request: I/O error, dev sdb, sector 24
[55089.021051] sd 3:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OK
[55089.021061] end_request: I/O error, dev sdb, sector 24
[55089.021259] sd 3:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OK
[55089.021269] end_request: I/O error, dev sdb, sector 0
[55089.021462] sd 3:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OK
[55089.021471] end_request: I/O error, dev sdb, sector 0
[55089.021493] unable to read partition table
[55089.026369] sd 3:0:0:0: [sdb] Attached SCSI disk
[55089.026598] sd 3:0:0:0: Attached scsi generic sg2 type 0
[55089.073268] usb 5-4: USB disconnect, address 4
[55101.344414] ACPI: \_SB_.PCI0.SATA.SECD.BAY_: found ejectable bay
[55101.344427] ACPI: \_SB_.PCI0.SATA.SECD.BAY_: Adding notify handler
[55101.346551] ACPI: Error installing bay notify handler
[55126.784051] usb 5-4: new high speed USB device using ehci_hcd and address 5
[55126.971125] usb 5-4: configuration #1 chosen from 1 choice
[55126.999189] scsi4 : SCSI emulation for USB Mass Storage devices
[55127.003346] usb-storage: device found at 5
[55127.003358] usb-storage: waiting for device to settle before scanning
[55132.000389] usb-storage: device scan complete
[55132.001998] scsi 4:0:0:0: Direct-Access ST980815 A D PQ: 0 ANSI: 2 CCS
[55132.054898] sd 4:0:0:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
[55132.057217] sd 4:0:0:0: [sdb] Write Protect is off
[55132.057230] sd 4:0:0:0: [sdb] Mode Sense: 00 38 00 00
[55132.057251] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[55132.060750] sd 4:0:0:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
[55132.062765] sd 4:0:0:0: [sdb] Write Protect is off
[55132.062777] sd 4:0:0:0: [sdb] Mode Sense: 00 38 00 00
[55132.062783] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[55132.067669] sdb: unknown partition table
[55132.087338] sd 4:0:0:0: [sdb] Attached SCSI disk
[55132.088320] sd 4:0:0:0: Attached scsi generic sg2 type 0
[55155.204177] usb 5-4: USB disconnect, address 5