nrune
May 20th, 2008, 10:05 PM
Well mythbuntu has installed beautifully and runs well I have a major problem however.
amd 64
eVGA 6200LE 256MB PCI-E Nvidia e-GeForce with TV/out
Asus A8R-MX/S
1 ddr2 ram
hauppauge pvr150
I have the video to go to svideo out and works really well until I click watch live tv. Then I get a black screen, and no key pressed will bring any kind of menu or response to the screen. When I unplug the svideo cable from the 6200le nvidia card nothing changes on the screen. I plugged in a monitor to the vga port and it did not have any signal so I am not sure where the problem is.
Dmesg is rather disturbing with a segfault.
[ 36.847206] Linux video capture interface: v2.00
[ 37.037473] nvidia: module license 'NVIDIA' taints kernel.
[ 37.395885] ivtv: Start initialization, version 1.1.0
[ 37.395993] ivtv0: Initializing card #0
[ 37.395996] ivtv0: Autodetected Hauppauge card (cx23416 based)
[ 37.416114] ACPI: PCI Interrupt 0000:02:11.0[A] -> GSI 18 (level, low) -> IRQ 18
[ 37.463809] lirc_dev: IR Remote Control driver registered, at major 61
[ 37.516309] tveeprom 0-0050: Hauppauge model 26552, rev F0A3, serial# 8919043
[ 37.516313] tveeprom 0-0050: tuner model is TCL MFNM05-4 (idx 103, type 43)
[ 37.516315] tveeprom 0-0050: TV standards NTSC(M) (eeprom 0x08)
[ 37.516317] tveeprom 0-0050: audio processor is CX25843 (idx 37)
[ 37.516319] tveeprom 0-0050: decoder processor is CX25843 (idx 30)
[ 37.516321] tveeprom 0-0050: has radio, has no IR receiver, has no IR transmitter
[ 37.516324] ivtv0: Autodetected Hauppauge WinTV PVR-150
[ 37.592643] tuner 0-0043: chip found @ 0x86 (ivtv i2c driver #0)
[ 37.592661] tda9887 0-0043: tda988[5/6/7] found @ 0x43 (tuner)
[ 37.592663] tuner 0-0043: type set to tda9887
[ 37.595634] tuner 0-0061: chip found @ 0xc2 (ivtv i2c driver #0)
[ 37.610677]
[ 37.610680] lirc_atiusb: USB remote driver for LIRC $Revision: 1.61 $
[ 37.610682] lirc_atiusb: Paul Miller <pmiller9@users.sourceforge.net>
[ 37.623223] input: Generic X-Box pad as /devices/pci0000:00/0000:00:1c.1/usb2/2-2/2-2:1.0/input/input6
[ 37.633474] usbcore: registered new interface driver xpad
[ 37.633480] /build/buildd/linux-2.6.24/drivers/input/joystick/xpad.c: X-Box pad driver:v0.0.6
[ 37.657394] lirc_atiusb[3]: inbound endpoint not found
[ 37.657412] usbcore: registered new interface driver lirc_atiusb
[ 37.679686] cx25840 0-0044: cx25843-24 found @ 0x88 (ivtv i2c driver #0)
[ 37.693733] wm8775 0-001b: chip found @ 0x36 (ivtv i2c driver #0)
[ 37.701513] tuner-simple 0-0061: type set to 43 (Philips NTSC MK3 (FM1236MK3 or FM1236/F))
[ 37.701516] tuner 0-0061: type set to Philips NTSC MK3 (F
[ 37.701840] ivtv0: Registered device video0 for encoder MPG (4096 kB)
[ 37.701853] ivtv0: Registered device video32 for encoder YUV (2048 kB)
[ 37.701866] ivtv0: Registered device vbi0 for encoder VBI (1024 kB)
[ 37.701878] ivtv0: Registered device video24 for encoder PCM (320 kB)
[ 37.701894] ivtv0: Registered device radio0 for encoder radio
[ 37.701897] ivtv0: Initialized card #0: Hauppauge WinTV PVR-150
[ 37.701909] ivtv: End initialization
[ 37.702642] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 18 (level, low) -> IRQ 18
[ 37.702649] PCI: Setting latency timer of device 0000:01:00.0 to 64
[ 37.702807] NVRM: loading NVIDIA UNIX x86_64 Kernel Module 169.12 Thu Feb 14 17:51:09 PST 2008
[ 37.704126] ACPI: PCI Interrupt 0000:00:1d.0[C] -> GSI 22 (level, low) -> IRQ 22
[ 39.236037] lp0: using parport0 (interrupt-driven).
[ 39.505527] Adding 3012148k swap on /dev/hda5. Priority:-1 extents:1 across:3012148k
[ 40.212194] EXT3 FS on hda1, internal journal
[ 41.779041] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 44.206111] No dock devices found.
[ 44.662879] powernow-k8: Found 1 AMD Athlon(tm) 64 Processor 3700+ processors (1 cpu cores) (version 2.20.00)
[ 44.662913] powernow-k8: 0 : fid 0xe (2200 MHz), vid 0x8
[ 44.662915] powernow-k8: 1 : fid 0xc (2000 MHz), vid 0xa
[ 44.662916] powernow-k8: 2 : fid 0xa (1800 MHz), vid 0xc
[ 44.662918] powernow-k8: 3 : fid 0x2 (1000 MHz), vid 0x12
[ 46.558045] NET: Registered protocol family 10
[ 46.558539] lo: Disabled Privacy Extensions
[ 53.937103] Marking TSC unstable due to cpufreq changes
[ 53.941010] Time: acpi_pm clocksource has been installed.
[ 54.104490] Clocksource tsc unstable (delta = -201134949 ns)
[ 54.721620] ivtv0: Loaded v4l-cx2341x-enc.fw firmware (376836 bytes)
[ 54.811145] ivtv0: Encoder revision: 0x02060039
[ 57.518190] cx25840 0-0044: loaded v4l-cx25840.fw firmware (16382 bytes)
[ 58.855213] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 60.482803] uli526x: eth0 NIC Link is Down
[ 60.803931] lirc_serial: auto-detected active high receiver
[ 60.803935] lirc_dev: lirc_register_plugin: sample_rate: 0
[ 66.728796] uli526x: eth0 NIC Link is Up 100 Mbps Full duplex
[ 66.729538] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 68.936412] NET: Registered protocol family 17
[ 76.456445] eth0: no IPv6 routers present
[ 202.483629] mythfrontend.re[6522]: segfault at 9eeba0 rip 9eeba0 rsp 43ba6d88 error 15
[ 341.211396] mythtv-setup.re[6878]: segfault at 128 rip 7f3a728336fa rsp 432ef470 error 4
[ 756.398138] mythfrontend.re[7459]: segfault at 9fccb0 rip 9fccb0 rsp 43e3dd88 error 15
[ 842.462728] mythfrontend.re[7752]: segfault at 9e5780 rip 9e5780 rsp 446e5d88 error 15
Help?
Additional info:
Glxgears and glxinfo looks great direct render etc. Don't think the problem is with the 6200le I feel like the video is going elsewhere besides svideo, but I am not sure where or how. Any ideas?
Mike
amd 64
eVGA 6200LE 256MB PCI-E Nvidia e-GeForce with TV/out
Asus A8R-MX/S
1 ddr2 ram
hauppauge pvr150
I have the video to go to svideo out and works really well until I click watch live tv. Then I get a black screen, and no key pressed will bring any kind of menu or response to the screen. When I unplug the svideo cable from the 6200le nvidia card nothing changes on the screen. I plugged in a monitor to the vga port and it did not have any signal so I am not sure where the problem is.
Dmesg is rather disturbing with a segfault.
[ 36.847206] Linux video capture interface: v2.00
[ 37.037473] nvidia: module license 'NVIDIA' taints kernel.
[ 37.395885] ivtv: Start initialization, version 1.1.0
[ 37.395993] ivtv0: Initializing card #0
[ 37.395996] ivtv0: Autodetected Hauppauge card (cx23416 based)
[ 37.416114] ACPI: PCI Interrupt 0000:02:11.0[A] -> GSI 18 (level, low) -> IRQ 18
[ 37.463809] lirc_dev: IR Remote Control driver registered, at major 61
[ 37.516309] tveeprom 0-0050: Hauppauge model 26552, rev F0A3, serial# 8919043
[ 37.516313] tveeprom 0-0050: tuner model is TCL MFNM05-4 (idx 103, type 43)
[ 37.516315] tveeprom 0-0050: TV standards NTSC(M) (eeprom 0x08)
[ 37.516317] tveeprom 0-0050: audio processor is CX25843 (idx 37)
[ 37.516319] tveeprom 0-0050: decoder processor is CX25843 (idx 30)
[ 37.516321] tveeprom 0-0050: has radio, has no IR receiver, has no IR transmitter
[ 37.516324] ivtv0: Autodetected Hauppauge WinTV PVR-150
[ 37.592643] tuner 0-0043: chip found @ 0x86 (ivtv i2c driver #0)
[ 37.592661] tda9887 0-0043: tda988[5/6/7] found @ 0x43 (tuner)
[ 37.592663] tuner 0-0043: type set to tda9887
[ 37.595634] tuner 0-0061: chip found @ 0xc2 (ivtv i2c driver #0)
[ 37.610677]
[ 37.610680] lirc_atiusb: USB remote driver for LIRC $Revision: 1.61 $
[ 37.610682] lirc_atiusb: Paul Miller <pmiller9@users.sourceforge.net>
[ 37.623223] input: Generic X-Box pad as /devices/pci0000:00/0000:00:1c.1/usb2/2-2/2-2:1.0/input/input6
[ 37.633474] usbcore: registered new interface driver xpad
[ 37.633480] /build/buildd/linux-2.6.24/drivers/input/joystick/xpad.c: X-Box pad driver:v0.0.6
[ 37.657394] lirc_atiusb[3]: inbound endpoint not found
[ 37.657412] usbcore: registered new interface driver lirc_atiusb
[ 37.679686] cx25840 0-0044: cx25843-24 found @ 0x88 (ivtv i2c driver #0)
[ 37.693733] wm8775 0-001b: chip found @ 0x36 (ivtv i2c driver #0)
[ 37.701513] tuner-simple 0-0061: type set to 43 (Philips NTSC MK3 (FM1236MK3 or FM1236/F))
[ 37.701516] tuner 0-0061: type set to Philips NTSC MK3 (F
[ 37.701840] ivtv0: Registered device video0 for encoder MPG (4096 kB)
[ 37.701853] ivtv0: Registered device video32 for encoder YUV (2048 kB)
[ 37.701866] ivtv0: Registered device vbi0 for encoder VBI (1024 kB)
[ 37.701878] ivtv0: Registered device video24 for encoder PCM (320 kB)
[ 37.701894] ivtv0: Registered device radio0 for encoder radio
[ 37.701897] ivtv0: Initialized card #0: Hauppauge WinTV PVR-150
[ 37.701909] ivtv: End initialization
[ 37.702642] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 18 (level, low) -> IRQ 18
[ 37.702649] PCI: Setting latency timer of device 0000:01:00.0 to 64
[ 37.702807] NVRM: loading NVIDIA UNIX x86_64 Kernel Module 169.12 Thu Feb 14 17:51:09 PST 2008
[ 37.704126] ACPI: PCI Interrupt 0000:00:1d.0[C] -> GSI 22 (level, low) -> IRQ 22
[ 39.236037] lp0: using parport0 (interrupt-driven).
[ 39.505527] Adding 3012148k swap on /dev/hda5. Priority:-1 extents:1 across:3012148k
[ 40.212194] EXT3 FS on hda1, internal journal
[ 41.779041] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 44.206111] No dock devices found.
[ 44.662879] powernow-k8: Found 1 AMD Athlon(tm) 64 Processor 3700+ processors (1 cpu cores) (version 2.20.00)
[ 44.662913] powernow-k8: 0 : fid 0xe (2200 MHz), vid 0x8
[ 44.662915] powernow-k8: 1 : fid 0xc (2000 MHz), vid 0xa
[ 44.662916] powernow-k8: 2 : fid 0xa (1800 MHz), vid 0xc
[ 44.662918] powernow-k8: 3 : fid 0x2 (1000 MHz), vid 0x12
[ 46.558045] NET: Registered protocol family 10
[ 46.558539] lo: Disabled Privacy Extensions
[ 53.937103] Marking TSC unstable due to cpufreq changes
[ 53.941010] Time: acpi_pm clocksource has been installed.
[ 54.104490] Clocksource tsc unstable (delta = -201134949 ns)
[ 54.721620] ivtv0: Loaded v4l-cx2341x-enc.fw firmware (376836 bytes)
[ 54.811145] ivtv0: Encoder revision: 0x02060039
[ 57.518190] cx25840 0-0044: loaded v4l-cx25840.fw firmware (16382 bytes)
[ 58.855213] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 60.482803] uli526x: eth0 NIC Link is Down
[ 60.803931] lirc_serial: auto-detected active high receiver
[ 60.803935] lirc_dev: lirc_register_plugin: sample_rate: 0
[ 66.728796] uli526x: eth0 NIC Link is Up 100 Mbps Full duplex
[ 66.729538] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 68.936412] NET: Registered protocol family 17
[ 76.456445] eth0: no IPv6 routers present
[ 202.483629] mythfrontend.re[6522]: segfault at 9eeba0 rip 9eeba0 rsp 43ba6d88 error 15
[ 341.211396] mythtv-setup.re[6878]: segfault at 128 rip 7f3a728336fa rsp 432ef470 error 4
[ 756.398138] mythfrontend.re[7459]: segfault at 9fccb0 rip 9fccb0 rsp 43e3dd88 error 15
[ 842.462728] mythfrontend.re[7752]: segfault at 9e5780 rip 9e5780 rsp 446e5d88 error 15
Help?
Additional info:
Glxgears and glxinfo looks great direct render etc. Don't think the problem is with the 6200le I feel like the video is going elsewhere besides svideo, but I am not sure where or how. Any ideas?
Mike