survient
April 25th, 2008, 04:15 PM
Each time I try to burn in gnomebaker I get the following errors:
wodim: No write mode specified.
wodim: Asuming -tao mode.
wodim: Future versions of wodim may have different drive dependent defaults.
scsidev: '/dev/hdb'
devname: '/dev/hdb'
scsibus: -2 target: -2 lun: -2
Linux sg driver version: 3.5.27
Wodim version: 1.1.6
SCSI buffer size: 64512
Beginning DMA speed test. Set CDR_NODMATEST environment variable if device
communication breaks or freezes immediately after that.
TOC Type: 3 = CD-ROM XA mode 2
Device type : Removable CD-ROM
Version : 0
Response Format: 2
Capabilities :
Vendor_info : 'TSSTcorp'
Identification : 'CD-R/RW TS-H292C'
Revision : 'HP01'
Device seems to be: Generic mmc CD-RW.
Current: 0x0009 (CD-R)
Profile: 0x000A (CD-RW)
Profile: 0x0009 (CD-R) (current)
Profile: 0x0008 (CD-ROM)
Using generic SCSI-3/mmc CD-R/CD-RW driver (mmc_cdr).
Driver flags : MMC-3 SWABAUDIO BURNFREE
Supported modes: TAO PACKET SAO SAO/R96R RAW/R16 RAW/R96R
Drive buf size : 1016064 = 992 KB
FIFO size : 12582912 = 12288 KB
Speed set to 1411 KB/s
4 seconds. 3 seconds. 2 seconds. 1 seconds. 0 seconds. Operation starts.
Waiting for reader process to fill input buffer ... input buffer ready.
Performing OPC...
Errno: 0 (Success), send opc scsi sendcmd: no error
CDB: 54 01 00 00 00 00 00 00 00 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 03 00 00 00 00 0A 00 00 00 00 73 03 00 00
Sense Key: 0x3 Medium Error, Segment 0
Sense Code: 0x73 Qual 0x03 (power calibration area error) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 0.308s timeout 60s
wodim: OPC failed.
Writing time: 4.428s
BURN-Free was never needed.
wodim: fifo had 192 puts and 0 gets.
wodim: fifo was 0 times empty and 0 times full, min fill was 100%.
Any ideas?
wodim: No write mode specified.
wodim: Asuming -tao mode.
wodim: Future versions of wodim may have different drive dependent defaults.
scsidev: '/dev/hdb'
devname: '/dev/hdb'
scsibus: -2 target: -2 lun: -2
Linux sg driver version: 3.5.27
Wodim version: 1.1.6
SCSI buffer size: 64512
Beginning DMA speed test. Set CDR_NODMATEST environment variable if device
communication breaks or freezes immediately after that.
TOC Type: 3 = CD-ROM XA mode 2
Device type : Removable CD-ROM
Version : 0
Response Format: 2
Capabilities :
Vendor_info : 'TSSTcorp'
Identification : 'CD-R/RW TS-H292C'
Revision : 'HP01'
Device seems to be: Generic mmc CD-RW.
Current: 0x0009 (CD-R)
Profile: 0x000A (CD-RW)
Profile: 0x0009 (CD-R) (current)
Profile: 0x0008 (CD-ROM)
Using generic SCSI-3/mmc CD-R/CD-RW driver (mmc_cdr).
Driver flags : MMC-3 SWABAUDIO BURNFREE
Supported modes: TAO PACKET SAO SAO/R96R RAW/R16 RAW/R96R
Drive buf size : 1016064 = 992 KB
FIFO size : 12582912 = 12288 KB
Speed set to 1411 KB/s
4 seconds. 3 seconds. 2 seconds. 1 seconds. 0 seconds. Operation starts.
Waiting for reader process to fill input buffer ... input buffer ready.
Performing OPC...
Errno: 0 (Success), send opc scsi sendcmd: no error
CDB: 54 01 00 00 00 00 00 00 00 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 03 00 00 00 00 0A 00 00 00 00 73 03 00 00
Sense Key: 0x3 Medium Error, Segment 0
Sense Code: 0x73 Qual 0x03 (power calibration area error) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 0.308s timeout 60s
wodim: OPC failed.
Writing time: 4.428s
BURN-Free was never needed.
wodim: fifo had 192 puts and 0 gets.
wodim: fifo was 0 times empty and 0 times full, min fill was 100%.
Any ideas?