drewdlephone
April 21st, 2008, 03:07 PM
Hey all. I know there are many how-tos on this subject, and I have gone over all of them, and am at a halt here. The two pieces of software required to make the Tascam work, the ALSA firmware and the usx2yloader, are both updated to the newest versions (1.0.15 & 0.1b, respectively), and yet I can't get an initialization to go through. When I type:
usx2yloader
I get this output:
usx2yloader: no usx2y compatible cards found
I'm also having an issue with bus support. I know my motherboard is working fine from a USB standpoint, as I've tested with other devices and had success. But every time I try the initialization command, the bus number on the card changes. So whereas I was at /002/002 when I first tried it, I was at 002/003 afterwards. Here's the output from both the audio card query and lsusb.
drew@GiR:~$ lsusb
Bus 003 Device 001: ID 0000:0000
Bus 002 Device 002: ID 058f:9360 Alcor Micro Corp. 8-in-1 Media Card Reader
Bus 002 Device 001: ID 0000:0000
Bus 001 Device 006: ID 1604:8007 Tascam US-122 Audio/Midi Interface
Bus 001 Device 001: ID 0000:0000
drew@GiR:~$ cat /proc/asound/cards
0 [IXP ]: ATIIXP - ATI IXP
ATI IXP rev 2 with ALC658D at 0xfe02a000, irq 22
1 [USX2Y ]: USB US-X2Y - TASCAM US-X2Y
TASCAM US-X2Y (1604:8007 if 0 at 001/006)
I had this working under Gutsy no problem; I followed the Community Documentation on getting it working, both times with success. So I'm at a bit of a loss here. Especially considering the system sees it under CAT as a USX2Y card, but the initializer says I don't have a compatible card. Anyone have any experience with this?
usx2yloader
I get this output:
usx2yloader: no usx2y compatible cards found
I'm also having an issue with bus support. I know my motherboard is working fine from a USB standpoint, as I've tested with other devices and had success. But every time I try the initialization command, the bus number on the card changes. So whereas I was at /002/002 when I first tried it, I was at 002/003 afterwards. Here's the output from both the audio card query and lsusb.
drew@GiR:~$ lsusb
Bus 003 Device 001: ID 0000:0000
Bus 002 Device 002: ID 058f:9360 Alcor Micro Corp. 8-in-1 Media Card Reader
Bus 002 Device 001: ID 0000:0000
Bus 001 Device 006: ID 1604:8007 Tascam US-122 Audio/Midi Interface
Bus 001 Device 001: ID 0000:0000
drew@GiR:~$ cat /proc/asound/cards
0 [IXP ]: ATIIXP - ATI IXP
ATI IXP rev 2 with ALC658D at 0xfe02a000, irq 22
1 [USX2Y ]: USB US-X2Y - TASCAM US-X2Y
TASCAM US-X2Y (1604:8007 if 0 at 001/006)
I had this working under Gutsy no problem; I followed the Community Documentation on getting it working, both times with success. So I'm at a bit of a loss here. Especially considering the system sees it under CAT as a USX2Y card, but the initializer says I don't have a compatible card. Anyone have any experience with this?