brokencrystal
February 15th, 2008, 08:05 AM
fowlers@eMachines:~$ dmesg | tail -25
[ 261.264805] usb 3-4: configuration #1 chosen from 1 choice
[ 310.889340] usb 3-4: USB disconnect, address 4
[ 316.998433] hub 2-1:1.0: port 3 disabled by hub (EMI?), re-enabling...
[ 316.998445] usb 2-1.3: USB disconnect, address 3
[ 317.070369] usb 2-1.3: new low speed USB device using ohci_hcd and address 4
[ 317.177406] usb 2-1.3: configuration #1 chosen from 1 choice
[ 317.184627] input: Logitech Optical USB Mouse as /class/input/input6
[ 317.184713] input: USB HID v1.10 Mouse [Logitech Optical USB Mouse] on usb-0000:00:13.1-1.3
[ 321.738970] usb 2-1.2: new full speed USB device using ohci_hcd and address 5
[ 321.838873] usb 2-1.2: not running at top speed; connect to a high speed hub
[ 321.856005] usb 2-1.2: rejected 1 configuration due to insufficient available bus power
[ 321.856015] usb 2-1.2: no configuration chosen from 1 choice
[ 328.955848] usb 2-1.2: new config #1 exceeds power limit by 400mA
[ 362.939159] usb 2-1.2: USB disconnect, address 5
[ 374.802825] usb 3-1: new high speed USB device using ehci_hcd and address 5
[ 374.942891] usb 3-1: configuration #1 chosen from 1 choice
[ 399.208052] usb 3-1: USB disconnect, address 5
[ 415.849404] hub 2-1:1.0: port 3 disabled by hub (EMI?), re-enabling...
[ 415.849418] usb 2-1.3: USB disconnect, address 4
[ 415.926250] usb 2-1.3: new low speed USB device using ohci_hcd and address 6
[ 416.033291] usb 2-1.3: configuration #1 chosen from 1 choice
[ 416.043625] input: Logitech Optical USB Mouse as /class/input/input7
[ 416.043709] input: USB HID v1.10 Mouse [Logitech Optical USB Mouse] on usb-0000:00:13.1-1.3
[ 522.090542] usb 3-5: new high speed USB device using ehci_hcd and address 6
[ 522.231808] usb 3-5: configuration #1 chosen from 1 choice
fowlers@eMachines:~$
brokencrystal
February 15th, 2008, 05:29 PM
Try removing all of your other USB devices (even the mouse if you have an old PS/2 mouse) then post again. It looks like your hub may be drawing too much current causing it to shut down.
Also note that I assume the Zune is on Bus 3-Device-6 but dmesg doesn't show enumeration by the kernel. So you would either need to load a module (sudo modprobe mszune, for example) or check for a newer kernel with support for it. You will have to do some research to see if a newer kernel (such as 2.6.24) has built-in support for it.
Also post differences between (dmesg, lsusb, lsmod) using Virtual Box and Ubuntu-only.
You might need to file a bug/feature request for Virtual Box on this matter, but search to see if it has already been posted.
I think the reason for the surge was when I tried to plug the Zune into my keyboard's built-in USB 1.1 hub. Here is with the mouse and the hub that is built into the keyboard both unplugged:
fowlers@eMachines:~$ lsmod
Module Size Used by
ipv6 273892 10
af_packet 24840 2
binfmt_misc 12936 1
rfcomm 42136 2
l2cap 26240 11 rfcomm
bluetooth 57060 4 rfcomm,l2cap
vboxdrv 60208 0
ppdev 10244 0
acpi_cpufreq 10568 0
cpufreq_stats 7232 0
cpufreq_powersave 2688 0
cpufreq_conservative 8072 0
cpufreq_ondemand 9612 2
freq_table 5792 3 acpi_cpufreq,cpufreq_stats,cpufreq_ondemand
cpufreq_userspace 5280 0
container 5504 0
ac 6148 0
button 8976 0
video 18060 0
sbs 19592 0
dock 10656 0
battery 11012 0
lp 12580 0
snd_hda_intel 263840 1
snd_pcm_oss 44672 0
snd_mixer_oss 17664 1 snd_pcm_oss
snd_pcm 80388 2 snd_hda_intel,snd_pcm_oss
snd_seq_dummy 4740 0
snd_seq_oss 33152 0
snd_seq_midi 9600 0
snd_rawmidi 25728 1 snd_seq_midi
snd_seq_midi_event 8448 2 snd_seq_oss,snd_seq_midi
snd_seq 53232 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_mid i_event
sg 36764 0
snd_timer 24324 2 snd_pcm,snd_seq
snd_seq_device 9228 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi ,snd_seq
sd_mod 30336 0
psmouse 39952 0
serio_raw 8068 0
pcspkr 4224 0
parport_pc 37412 1
parport 37448 3 ppdev,lp,parport_pc
snd 54660 11 snd_hda_intel,snd_pcm_oss,snd_mixer_oss,snd_pcm,sn d_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_de vice
soundcore 8800 1 snd
fglrx 1476940 20
snd_page_alloc 11400 2 snd_hda_intel,snd_pcm
i2c_piix4 9740 0
i2c_core 26112 1 i2c_piix4
shpchp 34580 0
ati_agp 10124 0
agpgart 35016 2 fglrx,ati_agp
pci_hotplug 32704 1 shpchp
evdev 11136 3
ext3 133896 1
jbd 60456 1 ext3
mbcache 9732 1 ext3
ide_disk 18560 3
ide_cd 32672 0
cdrom 37536 1 ide_cd
usbhid 29536 0
hid 28928 1 usbhid
usb_storage 73024 0
ata_generic 8452 0
libusual 18448 1 usb_storage
8139too 27776 0
atiixp 7056 0 [permanent]
ide_core 116804 4 ide_disk,ide_cd,usb_storage,atiixp
sata_sil 12168 0
libata 125168 2 ata_generic,sata_sil
scsi_mod 147084 4 sg,sd_mod,usb_storage,libata
8139cp 25088 0
mii 6528 2 8139too,8139cp
ehci_hcd 36492 0
ohci_hcd 22916 0
usbcore 138632 6 usbhid,usb_storage,libusual,ehci_hcd,ohci_hcd
thermal 14344 0
processor 32072 2 acpi_cpufreq,thermal
fan 5764 0
fuse 47124 1
apparmor 40728 0
commoncap 8320 1 apparmor
fowlers@eMachines:~$
fowlers@eMachines:~$ lsusb
Bus 003 Device 011: ID 045e:0710 Microsoft Corp.
Bus 003 Device 003: ID 058f:6377 Alcor Micro Corp.
Bus 003 Device 001: ID 0000:0000
Bus 002 Device 001: ID 0000:0000
Bus 001 Device 001: ID 0000:0000
fowlers@eMachines:~$ dmesg
[ 0.000000] Linux version 2.6.22-14-generic (buildd@terranova) (gcc version 4.1.3 20070929 (prerelease) (Ubuntu 4.1.2-16ubuntu2)) #1 SMP Tue Feb 12 07:42:25 UTC 2008 (Ubuntu 2.6.22-14.52-generic)
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000007ef60000 (usable)
[ 0.000000] BIOS-e820: 000000007ef60000 - 000000007f004000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000007f004000 - 000000007fd90000 (usable)
[ 0.000000] BIOS-e820: 000000007fd90000 - 000000007fd98000 (reserved)
[ 0.000000] BIOS-e820: 000000007fd98000 - 000000007fe2e000 (usable)
[ 0.000000] BIOS-e820: 000000007fe2e000 - 000000007fe32000 (reserved)
[ 0.000000] BIOS-e820: 000000007fe32000 - 000000007feab000 (usable)
[ 0.000000] BIOS-e820: 000000007feab000 - 000000007feef000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000007feef000 - 000000007fef1000 (usable)
[ 0.000000] BIOS-e820: 000000007fef1000 - 000000007feff000 (ACPI data)
[ 0.000000] BIOS-e820: 000000007feff000 - 000000007ff00000 (usable)
[ 0.000000] BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
[ 0.000000] 1151MB HIGHMEM available.
[ 0.000000] 896MB LOWMEM available.
[ 0.000000] found SMP MP-table at 000fe860
[ 0.000000] Entering add_active_range(0, 0, 524032) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 229376
[ 0.000000] HighMem 229376 -> 524032
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 524032
[ 0.000000] On node 0 totalpages: 524032
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 1760 pages used for memmap
[ 0.000000] Normal zone: 223520 pages, LIFO batch:31
[ 0.000000] HighMem zone: 2302 pages used for memmap
[ 0.000000] HighMem zone: 292354 pages, LIFO batch:31
[ 0.000000] DMI 2.4 present.
[ 0.000000] ACPI: RSDP signature @ 0xC00FE020 checksum 0
[ 0.000000] ACPI: RSDP 000FE020, 0014 (r0 GATEWA)
[ 0.000000] ACPI: RSDT 7FEFE038, 0048 (r1 GATEWA SYSTEM 7E8 1000013)
[ 0.000000] ACPI: FACP 7FEFD000, 0074 (r1 GATEWA SYSTEM 7E8 MSFT 1000013)
[ 0.000000] ACPI: DSDT 7FEF9000, 3918 (r1 GATEWA SYSTEM 7E8 MSFT 1000013)
[ 0.000000] ACPI: FACS 7FEAB000, 0040
[ 0.000000] ACPI: APIC 7FEF8000, 0084 (r1 GATEWA SYSTEM 7E8 MSFT 1000013)
[ 0.000000] ACPI: MCFG 7FEF7000, 003C (r1 GATEWA SYSTEM 7E8 MSFT 1000013)
[ 0.000000] ACPI: SSDT 7FEF6000, 01B4 (r1 GATEWA SYSTEM 7E8 MSFT 1000013)
[ 0.000000] ACPI: SSDT 7FEF5000, 0175 (r1 GATEWA SYSTEM 7E8 MSFT 1000013)
[ 0.000000] ACPI: SSDT 7FEF4000, 0175 (r1 GATEWA SYSTEM 7E8 MSFT 1000013)
[ 0.000000] ACPI: SSDT 7FEF3000, 0175 (r1 GATEWA SYSTEM 7E8 MSFT 1000013)
[ 0.000000] ACPI: SSDT 7FEF2000, 0175 (r1 GATEWA SYSTEM 7E8 MSFT 1000013)
[ 0.000000] ACPI: SLIC 7FEF1000, 0176 (r1 GATEWA SYSTEM 7E8 MSFT 1000013)
[ 0.000000] ATI board detected. Disabling timer routing over 8254.
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 15:6 APIC version 20
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] Processor #1 15:6 APIC version 20
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x01] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] disabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 4, version 33, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 21 low level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 80000000 (gap: 7ff00000:80080000)
[ 0.000000] Built 1 zonelists. Total pages: 519938
[ 0.000000] Kernel command line: root=UUID=b064cdc5-3d6e-4493-8797-79fe9d63b3b9 ro quiet splash
[ 0.000000] mapped APIC to ffffd000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffc000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Detected 3000.654 MHz processor.
[ 36.588341] Console: colour VGA+ 80x25
[ 36.588987] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 36.589506] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 36.686849] Memory: 2065600k/2096128k available (2015k kernel code, 28176k reserved, 915k data, 364k init, 1177592k highmem)
[ 36.686859] virtual kernel memory layout:
[ 36.686860] fixmap : 0xfff4d000 - 0xfffff000 ( 712 kB)
[ 36.686861] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 36.686863] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
[ 36.686864] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
[ 36.686865] .init : 0xc03e3000 - 0xc043e000 ( 364 kB)
[ 36.686866] .data : 0xc02f7e86 - 0xc03dce84 ( 915 kB)
[ 36.686867] .text : 0xc0100000 - 0xc02f7e86 (2015 kB)
[ 36.686870] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 36.686923] SLUB: Genslabs=22, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1
[ 36.766885] Calibrating delay using timer specific routine.. 6007.46 BogoMIPS (lpj=12014938)
[ 36.766922] Security Framework v1.0.0 initialized
[ 36.766929] SELinux: Disabled at boot.
[ 36.766943] Mount-cache hash table entries: 512
[ 36.767109] CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e59d 00000000 00000001
[ 36.767118] monitor/mwait feature present.
[ 36.767120] using mwait in idle threads.
[ 36.767128] CPU: Trace cache: 12K uops, L1 D cache: 16K
[ 36.767131] CPU: L2 cache: 2048K
[ 36.767134] CPU: Physical Processor ID: 0
[ 36.767136] CPU: After all inits, caps: bfebfbff 20100000 00000000 0000b180 0000e59d 00000000 00000001
[ 36.767150] Compat vDSO mapped to ffffe000.
[ 36.767168] Checking 'hlt' instruction... OK.
[ 36.783026] SMP alternatives: switching to UP code
[ 36.783642] Early unpacking initramfs... done
[ 37.067474] ACPI: Core revision 20070126
[ 37.067523] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
[ 37.079830] CPU0: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 05
[ 37.079849] SMP alternatives: switching to SMP code
[ 37.079968] Booting processor 1/1 eip 3000
[ 37.090267] Initializing CPU#1
[ 37.170526] Calibrating delay using timer specific routine.. 6000.71 BogoMIPS (lpj=12001439)
[ 37.170537] CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e59d 00000000 00000001
[ 37.170544] monitor/mwait feature present.
[ 37.170551] CPU: Trace cache: 12K uops, L1 D cache: 16K
[ 37.170555] CPU: L2 cache: 2048K
[ 37.170557] CPU: Physical Processor ID: 0
[ 37.170560] CPU: After all inits, caps: bfebfbff 20100000 00000000 0000b180 0000e59d 00000000 00000001
[ 37.171123] CPU1: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 05
[ 37.171168] Total of 2 processors activated (12008.18 BogoMIPS).
[ 37.171340] ENABLING IO-APIC IRQs
[ 37.171544] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 37.211246] ..MP-BIOS bug: 8254 timer not connected to IO-APIC
[ 37.211301] ...trying to set up timer (IRQ0) through the 8259A ... failed.
[ 37.211304] ...trying to set up timer as Virtual Wire IRQ... works.
[ 37.358480] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[ 37.378481] Brought up 2 CPUs
[ 37.424581] migration_cost=7
[ 37.424769] Booting paravirtualized kernel on bare hardware
[ 37.424858] Time: 11:55:41 Date: 01/15/108
[ 37.424884] NET: Registered protocol family 16
[ 37.424981] EISA bus registered
[ 37.424987] ACPI: bus type pci registered
[ 37.427924] PCI: Using configuration type 1
[ 37.427926] Setting up standard PCI resources
[ 37.446782] ACPI: EC: Look up EC in DSDT
[ 37.449679] ACPI: Interpreter enabled
[ 37.449683] ACPI: (supports S0 S1 S3 S4 S5)
[ 37.449706] ACPI: Using IOAPIC for interrupt routing
[ 37.454379] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 37.454389] PCI: Probing PCI hardware (bus 00)
[ 37.455872] PCI: Transparent bridge - 0000:00:14.4
[ 37.455920] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 37.456102] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB2_._PRT]
[ 37.456243] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
[ 37.459229] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 37.459335] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 37.459437] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 37.459538] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 37.459639] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 37.459739] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 37.459840] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 37.459941] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 37.460040] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 37.460051] pnp: PnP ACPI init
[ 37.460060] ACPI: bus type pnp registered
[ 37.462298] pnp: PnP ACPI: found 10 devices
[ 37.462301] ACPI: ACPI bus type pnp unregistered
[ 37.462306] PnPBIOS: Disabled by ACPI PNP
[ 37.462367] PCI: Using ACPI for IRQ routing
[ 37.462371] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 37.462475] NET: Registered protocol family 8
[ 37.462478] NET: Registered protocol family 20
[ 37.462545] pnp: 00:06: ioport range 0x400-0x4cf has been reserved
[ 37.462548] pnp: 00:06: ioport range 0x4d0-0x4d1 has been reserved
[ 37.462555] pnp: 00:07: iomem range 0x0-0x9ffff could not be reserved
[ 37.462558] pnp: 00:07: iomem range 0xec000-0xfffff could not be reserved
[ 37.462561] pnp: 00:07: iomem range 0x100000-0x7fffffff could not be reserved
[ 37.462565] pnp: 00:07: iomem range 0xe0000000-0xefffffff has been reserved
[ 37.466308] Time: tsc clocksource has been installed.
[ 37.492948] PCI: Bridge: 0000:00:02.0
[ 37.492952] IO window: 2000-2fff
[ 37.492957] MEM window: a0100000-a01fffff
[ 37.492961] PREFETCH window: 80000000-9fffffff
[ 37.492965] PCI: Bridge: 0000:00:14.4
[ 37.492969] IO window: 1000-1fff
[ 37.492977] MEM window: a0000000-a00fffff
[ 37.492982] PREFETCH window: disabled.
[ 37.493002] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 37.493014] PCI: Setting latency timer of device 0000:00:14.4 to 64
[ 37.493025] NET: Registered protocol family 2
[ 37.538383] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 37.538477] TCP established hash table entries: 131072 (order: 8, 1572864 bytes)
[ 37.539399] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 37.539714] TCP: Hash tables configured (established 131072 bind 65536)
[ 37.539717] TCP reno registered
[ 37.550548] checking if image is initramfs... it is
[ 37.993868] Switched to high resolution mode on CPU 0
[ 37.993951] Switched to high resolution mode on CPU 1
[ 38.112563] Freeing initrd memory: 7052k freed
[ 38.113196] audit: initializing netlink socket (disabled)
[ 38.113213] audit(1203076541.116:1): initialized
[ 38.113323] highmem bounce pool size: 64 pages
[ 38.115727] VFS: Disk quotas dquot_6.5.1
[ 38.115792] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 38.115902] io scheduler noop registered
[ 38.115905] io scheduler anticipatory registered
[ 38.115908] io scheduler deadline registered
[ 38.115924] io scheduler cfq registered (default)
[ 38.115940] PCI: MSI quirk detected. MSI deactivated.
[ 38.115965] Boot video device is 0000:01:00.0
[ 38.116056] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 38.116097] assign_interrupt_mode Found MSI capability
[ 38.116100] Allocate Port Service[0000:00:02.0:pcie00]
[ 38.116272] isapnp: Scanning for PnP cards...
[ 38.467639] isapnp: No Plug & Play device found
[ 38.495327] Real Time Clock Driver v1.12ac
[ 38.495439] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 38.495579] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 38.496341] 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 38.497111] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 38.497333] input: Macintosh mouse button emulation as /class/input/input0
[ 38.497418] PNP: PS/2 Controller [PNP0303:KBC0] at 0x60,0x64 irq 1
[ 38.497421] PNP: PS/2 controller doesn't have AUX irq; using default 12
[ 38.500246] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 38.500254] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 38.500437] mice: PS/2 mouse device common for all mice
[ 38.500572] EISA: Probing bus 0 at eisa.0
[ 38.500582] Cannot allocate resource for EISA slot 1
[ 38.500585] Cannot allocate resource for EISA slot 2
[ 38.500587] Cannot allocate resource for EISA slot 3
[ 38.500615] EISA: Detected 0 cards.
[ 38.500710] TCP cubic registered
[ 38.500722] NET: Registered protocol family 1
[ 38.500746] Using IPI No-Shortcut mode
[ 38.500921] Magic number: 12:158:934
[ 38.501375] Freeing unused kernel memory: 364k freed
[ 38.518932] input: AT Translated Set 2 keyboard as /class/input/input1
[ 39.856019] AppArmor: AppArmor initialized<5>audit(1203076542.616:2): type=1505 info="AppArmor initialized" pid=1194
[ 39.864430] fuse init (API version 7.8)
[ 39.869377] Failure registering capabilities with primary security module.
[ 39.910457] ACPI: Processor [CPU0] (supports 8 throttling states)
[ 39.910543] ACPI: Processor [CPU1] (supports 8 throttling states)
[ 39.910558] ACPI Exception (processor_core-0783): AE_NOT_FOUND, Processor Device is not present [20070126]
[ 39.910572] ACPI Exception (processor_core-0783): AE_NOT_FOUND, Processor Device is not present [20070126]
[ 40.514311] usbcore: registered new interface driver usbfs
[ 40.514349] usbcore: registered new interface driver hub
[ 40.514388] usbcore: registered new device driver usb
[ 40.515451] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[ 40.515491] PCI: Enabling device 0000:00:13.0 (0000 -> 0002)
[ 40.515507] ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> IRQ 16
[ 40.515526] ohci_hcd 0000:00:13.0: OHCI Host Controller
[ 40.515726] ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1
[ 40.515750] ohci_hcd 0000:00:13.0: irq 16, io mem 0xa0204000
[ 40.584755] usb usb1: configuration #1 chosen from 1 choice
[ 40.584807] hub 1-0:1.0: USB hub found
[ 40.584826] hub 1-0:1.0: 4 ports detected
[ 40.600920] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[ 40.616166] SCSI subsystem initialized
[ 40.623965] libata version 2.21 loaded.
[ 40.658542] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 40.658551] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 40.687863] PCI: Enabling device 0000:00:13.1 (0000 -> 0002)
[ 40.687875] ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 19 (level, low) -> IRQ 16
[ 40.687898] ohci_hcd 0000:00:13.1: OHCI Host Controller
[ 40.687936] ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 2
[ 40.687958] ohci_hcd 0000:00:13.1: irq 16, io mem 0xa0205000
[ 40.747726] usb usb2: configuration #1 chosen from 1 choice
[ 40.747771] hub 2-0:1.0: USB hub found
[ 40.747785] hub 2-0:1.0: 4 ports detected
[ 40.851831] PCI: Enabling device 0000:00:13.2 (0000 -> 0002)
[ 40.851840] ACPI: PCI Interrupt 0000:00:13.2[A] -> GSI 19 (level, low) -> IRQ 16
[ 40.851859] ehci_hcd 0000:00:13.2: EHCI Host Controller
[ 40.851897] ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 3
[ 40.851958] ehci_hcd 0000:00:13.2: irq 16, io mem 0xa0206000
[ 40.851974] ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 40.852079] usb usb3: configuration #1 chosen from 1 choice
[ 40.852121] hub 3-0:1.0: USB hub found
[ 40.852132] hub 3-0:1.0: 8 ports detected
[ 40.955726] 8139cp 0000:02:02.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip
[ 40.955735] 8139cp 0000:02:02.0: Try the "8139too" driver instead.
[ 40.958426] 8139too Fast Ethernet driver 0.9.28
[ 40.958491] ACPI: PCI Interrupt 0000:02:02.0[A] -> GSI 21 (level, low) -> IRQ 21
[ 40.958508] PCI: Setting latency timer of device 0000:02:02.0 to 64
[ 40.959270] eth0: RealTek RTL8139 at 0xf8846000, 00:19:d1:52:85:ca, IRQ 21
[ 40.959274] eth0: Identified 8139 chip type 'RTL-8101'
[ 40.959400] sata_sil 0000:00:11.0: version 2.2
[ 40.959472] ACPI: PCI Interrupt 0000:00:11.0[A] -> GSI 23 (level, low) -> IRQ 17
[ 40.959494] PCI: Setting latency timer of device 0000:00:11.0 to 64
[ 40.959580] scsi0 : sata_sil
[ 40.959850] scsi1 : sata_sil
[ 40.959904] ata1: SATA max UDMA/100 cmd 0xf8844680 ctl 0xf884468a bmdma 0xf8844600 irq 17
[ 40.959911] ata2: SATA max UDMA/100 cmd 0xf88446c0 ctl 0xf88446ca bmdma 0xf8844608 irq 17
[ 41.271198] ata1: SATA link down (SStatus 0 SControl 310)
[ 41.582941] ata2: SATA link down (SStatus 0 SControl 310)
[ 41.583037] ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 22 (level, low) -> IRQ 18
[ 41.583059] PCI: Setting latency timer of device 0000:00:12.0 to 64
[ 41.583107] scsi2 : sata_sil
[ 41.583173] scsi3 : sata_sil
[ 41.583221] ata3: SATA max UDMA/100 cmd 0xf8868480 ctl 0xf886848a bmdma 0xf8868400 irq 18
[ 41.583228] ata4: SATA max UDMA/100 cmd 0xf88684c0 ctl 0xf88684ca bmdma 0xf8868408 irq 18
[ 41.586955] usb 3-7: new high speed USB device using ehci_hcd and address 3
[ 41.721031] usb 3-7: configuration #1 chosen from 1 choice
[ 41.894696] ata3: SATA link down (SStatus 0 SControl 310)
[ 42.022595] usb 2-1: new full speed USB device using ohci_hcd and address 2
[ 42.206432] ata4: SATA link down (SStatus 0 SControl 310)
[ 42.206510] ATIIXP: IDE controller at PCI slot 0000:00:14.1
[ 42.206545] ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 19
[ 42.206561] ATIIXP: chipset revision 128
[ 42.206565] ATIIXP: not 100% native mode: will probe irqs later
[ 42.206578] ide0: BM-DMA at 0x3000-0x3007, BIOS settings: hda:DMA, hdb:pio
[ 42.206599] ide1: BM-DMA at 0x3008-0x300f, BIOS settings: hdc:DMA, hdd:pio
[ 42.206614] Probing IDE interface ide0...
[ 42.223381] usb 2-1: configuration #1 chosen from 1 choice
[ 42.225309] hub 2-1:1.0: USB hub found
[ 42.227251] hub 2-1:1.0: 4 ports detected
[ 42.494640] hda: Hitachi HDS721616PLAT80, ATA DISK drive
[ 42.550956] usb 2-1.3: new low speed USB device using ohci_hcd and address 3
[ 42.656970] usb 2-1.3: configuration #1 chosen from 1 choice
[ 42.662868] usbcore: registered new interface driver libusual
[ 42.669385] Initializing USB Mass Storage driver...
[ 42.669469] scsi4 : SCSI emulation for USB Mass Storage devices
[ 42.669532] usb-storage: device found at 3
[ 42.669535] usb-storage: waiting for device to settle before scanning
[ 42.669557] usbcore: registered new interface driver usb-storage
[ 42.669562] USB Mass Storage support registered.
[ 42.675562] usbcore: registered new interface driver hiddev
[ 42.680031] input: Logitech Optical USB Mouse as /class/input/input2
[ 42.680065] input: USB HID v1.10 Mouse [Logitech Optical USB Mouse] on usb-0000:00:13.1-1.3
[ 42.680082] usbcore: registered new interface driver usbhid
[ 42.680088] /build/buildd/linux-source-2.6.22-2.6.22/drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[ 43.165667] hda: selected mode 0x45
[ 43.165893] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 43.182192] Probing IDE interface ide1...
[ 43.917471] hdc: TSSTcorpCD/DVDW TS-H652D, ATAPI CD/DVD-ROM drive
[ 44.588505] hdc: selected mode 0x42
[ 44.588931] ide1 at 0x170-0x177,0x376 on irq 15
[ 44.607119] hda: max request size: 512KiB
[ 44.607316] hda: 321672960 sectors (164696 MB) w/7384KiB Cache, CHS=20023/255/63, UDMA(100)
[ 44.607516] hda: cache flushes supported
[ 44.607570] hda:<6>hdc: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
[ 44.609923] Uniform CD-ROM driver Revision: 3.20
[ 44.617622] hda1 hda2 < hda5 >
[ 44.796581] Attempting manual resume
[ 44.796586] swsusp: Resume From Partition 3:5
[ 44.796588] PM: Checking swsusp image.
[ 44.796723] PM: Resume from disk failed.
[ 44.835918] kjournald starting. Commit interval 5 seconds
[ 44.835932] EXT3-fs: mounted filesystem with ordered data mode.
[ 47.662161] usb-storage: device scan complete
[ 47.662765] scsi 4:0:0:0: Direct-Access Generic USB SD Reader 1.00 PQ: 0 ANSI: 0
[ 47.663392] scsi 4:0:0:1: Direct-Access Generic USB CF Reader 1.01 PQ: 0 ANSI: 0
[ 47.664017] scsi 4:0:0:2: Direct-Access Generic USB SM Reader 1.02 PQ: 0 ANSI: 0
[ 47.664515] scsi 4:0:0:3: Direct-Access Generic USB MS Reader 1.03 PQ: 0 ANSI: 0
[ 50.459314] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 50.549126] Linux agpgart interface v0.102 (c) Dave Jones
[ 50.570711] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 50.779387] piix4_smbus 0000:00:14.0: Found 0000:00:14.0 device
[ 51.141604] fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
[ 51.179120] [fglrx] Maximum main memory to use for locked dma buffers: 1898 MBytes.
[ 51.179178] [fglrx] ASYNCIO init succeed!
[ 51.180598] [fglrx] PAT is enabled successfully!
[ 51.180656] [fglrx] module loaded - fglrx 8.45.4 [Jan 16 2008] on minor 0
[ 51.425101] parport_pc 00:08: reported by Plug and Play ACPI
[ 51.425142] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE,EPP]
[ 51.465095] input: PC Speaker as /class/input/input3
[ 51.560232] sd 4:0:0:0: [sda] Attached SCSI removable disk
[ 51.561324] sd 4:0:0:1: [sdb] Attached SCSI removable disk
[ 51.562274] sd 4:0:0:2: [sdc] Attached SCSI removable disk
[ 51.563148] sd 4:0:0:3: [sdd] Attached SCSI removable disk
[ 51.586820] sd 4:0:0:0: Attached scsi generic sg0 type 0
[ 51.587057] sd 4:0:0:1: Attached scsi generic sg1 type 0
[ 51.587290] sd 4:0:0:2: Attached scsi generic sg2 type 0
[ 51.587525] sd 4:0:0:3: Attached scsi generic sg3 type 0
[ 51.966384] ACPI: PCI Interrupt 0000:00:14.2[A] -> GSI 16 (level, low) -> IRQ 19
[ 53.122837] lp0: using parport0 (interrupt-driven).
[ 53.169092] Adding 1309256k swap on /dev/hda5. Priority:-1 extents:1 across:1309256k
[ 53.527303] EXT3 FS on hda1, internal journal
[ 54.507844] No dock devices found.
[ 54.605804] input: Power Button (FF) as /class/input/input4
[ 54.605834] ACPI: Power Button (FF) [PWRF]
[ 54.605895] input: Power Button (CM) as /class/input/input5
[ 54.605931] ACPI: Power Button (CM) [PWRB]
[ 55.768941] ppdev: user-space parallel port driver
[ 55.944691] audit(1203076559.427:3): type=1503 operation="inode_permission" requested_mask="a" denied_mask="a" name="/dev/tty" pid=4885 profile="/usr/sbin/cupsd"
[ 56.024695] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[ 56.024702] apm: disabled - APM is not SMP safe.
[ 56.086530] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
[ 56.743656] vboxdrv: Trying to deactivate the NMI watchdog permanently...
[ 56.743665] vboxdrv: Successfully done.
[ 56.746391] vboxdrv: Successfully loaded version 1.5.4 (interface 0x00050002).
[ 57.096249] Failure registering capabilities with primary security module.
[ 57.296882] Bluetooth: Core ver 2.11
[ 57.297086] NET: Registered protocol family 31
[ 57.297092] Bluetooth: HCI device and connection manager initialized
[ 57.297098] Bluetooth: HCI socket layer initialized
[ 57.316207] Bluetooth: L2CAP ver 2.8
[ 57.316215] Bluetooth: L2CAP socket layer initialized
[ 57.353506] Bluetooth: RFCOMM socket layer initialized
[ 57.353691] Bluetooth: RFCOMM TTY layer initialized
[ 57.353698] Bluetooth: RFCOMM ver 1.8
[ 60.049153] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 18 (level, low) -> IRQ 20
[ 61.543775] NET: Registered protocol family 17
[ 64.052376] [fglrx] Reserve Block - 0 offset = 0X0 length = 0X40000
[ 64.052382] [fglrx] Reserve Block - 1 offset = 0X7fc0000 length = 0X40000
[ 64.236156] [fglrx] interrupt source 20008000 successfully enabled
[ 64.236163] [fglrx] enable ID = 0x00000004
[ 64.236176] [fglrx] Receive enable interrupt message with irqEnableMask: 20008000
[ 64.236771] [fglrx] interrupt source 10000000 successfully enabled
[ 64.236775] [fglrx] enable ID = 0x00000005
[ 64.236781] [fglrx] Receive enable interrupt message with irqEnableMask: 10000000
[ 64.499259] NET: Registered protocol family 10
[ 64.499609] lo: Disabled Privacy Extensions
[ 69.029215] hda-intel: Invalid position buffer, using LPIB read method instead.
[ 70.578044] [fglrx:firegl_free_mutex] *ERROR* mutex id 0x00000003 not found in mutex list
[ 70.639310] [fglrx:firegl_free_mutex] *ERROR* mutex id 0x00000002 not found in mutex list
[ 70.690652] [fglrx:firegl_free_mutex] *ERROR* mutex id 0x00000002 not found in mutex list
[ 70.745869] [fglrx:firegl_free_mutex] *ERROR* mutex id 0x00000002 not found in mutex list
[ 70.841933] [fglrx:firegl_free_mutex] *ERROR* mutex id 0x00000002 not found in mutex list
[ 75.079578] eth0: no IPv6 routers present
[ 261.123678] usb 3-4: new high speed USB device using ehci_hcd and address 4
[ 261.264805] usb 3-4: configuration #1 chosen from 1 choice
[ 310.889340] usb 3-4: USB disconnect, address 4
[ 316.998433] hub 2-1:1.0: port 3 disabled by hub (EMI?), re-enabling...
[ 316.998445] usb 2-1.3: USB disconnect, address 3
[ 317.070369] usb 2-1.3: new low speed USB device using ohci_hcd and address 4
[ 317.177406] usb 2-1.3: configuration #1 chosen from 1 choice
[ 317.184627] input: Logitech Optical USB Mouse as /class/input/input6
[ 317.184713] input: USB HID v1.10 Mouse [Logitech Optical USB Mouse] on usb-0000:00:13.1-1.3
[ 321.738970] usb 2-1.2: new full speed USB device using ohci_hcd and address 5
[ 321.838873] usb 2-1.2: not running at top speed; connect to a high speed hub
[ 321.856005] usb 2-1.2: rejected 1 configuration due to insufficient available bus power
[ 321.856015] usb 2-1.2: no configuration chosen from 1 choice
[ 328.955848] usb 2-1.2: new config #1 exceeds power limit by 400mA
[ 362.939159] usb 2-1.2: USB disconnect, address 5
[ 374.802825] usb 3-1: new high speed USB device using ehci_hcd and address 5
[ 374.942891] usb 3-1: configuration #1 chosen from 1 choice
[ 399.208052] usb 3-1: USB disconnect, address 5
[ 415.849404] hub 2-1:1.0: port 3 disabled by hub (EMI?), re-enabling...
[ 415.849418] usb 2-1.3: USB disconnect, address 4
[ 415.926250] usb 2-1.3: new low speed USB device using ohci_hcd and address 6
[ 416.033291] usb 2-1.3: configuration #1 chosen from 1 choice
[ 416.043625] input: Logitech Optical USB Mouse as /class/input/input7
[ 416.043709] input: USB HID v1.10 Mouse [Logitech Optical USB Mouse] on usb-0000:00:13.1-1.3
[ 522.090542] usb 3-5: new high speed USB device using ehci_hcd and address 6
[ 522.231808] usb 3-5: configuration #1 chosen from 1 choice
[ 1161.292530] usb 3-7: reset high speed USB device using ehci_hcd and address 3
[ 1161.425968] scsi5 : SCSI emulation for USB Mass Storage devices
[ 1161.426054] usb-storage: device found at 3
[ 1161.426059] usb-storage: waiting for device to settle before scanning
[ 1166.420475] usb-storage: device scan complete
[ 1166.421091] scsi 5:0:0:0: Direct-Access Generic USB SD Reader 1.00 PQ: 0 ANSI: 0
[ 1166.421714] scsi 5:0:0:1: Direct-Access Generic USB CF Reader 1.01 PQ: 0 ANSI: 0
[ 1166.422337] scsi 5:0:0:2: Direct-Access Generic USB SM Reader 1.02 PQ: 0 ANSI: 0
[ 1166.422961] scsi 5:0:0:3: Direct-Access Generic USB MS Reader 1.03 PQ: 0 ANSI: 0
[ 1166.424692] sd 5:0:0:0: [sda] Attached SCSI removable disk
[ 1166.424767] sd 5:0:0:0: Attached scsi generic sg0 type 0
[ 1166.426389] sd 5:0:0:1: [sdb] Attached SCSI removable disk
[ 1166.426461] sd 5:0:0:1: Attached scsi generic sg1 type 0
[ 1166.428253] sd 5:0:0:2: [sdc] Attached SCSI removable disk
[ 1166.428341] sd 5:0:0:2: Attached scsi generic sg2 type 0
[ 1166.430098] sd 5:0:0:3: [sdd] Attached SCSI removable disk
[ 1166.430169] sd 5:0:0:3: Attached scsi generic sg3 type 0
[ 1821.103793] usb 3-5: USB disconnect, address 6
[ 1842.424285] usb 3-5: new high speed USB device using ehci_hcd and address 7
[ 1842.566403] usb 3-5: configuration #1 chosen from 1 choice
[ 1880.658631] usb 3-5: USB disconnect, address 7
[ 1886.104598] usb 3-6: new high speed USB device using ehci_hcd and address 8
[ 1886.244834] usb 3-6: configuration #1 chosen from 1 choice
[ 1965.188020] usb 3-6: reset high speed USB device using ehci_hcd and address 8
[33281.959701] usb 3-6: USB disconnect, address 8
[33284.474759] usb 3-6: new high speed USB device using ehci_hcd and address 9
[33284.616020] usb 3-6: configuration #1 chosen from 1 choice
[33312.958910] usb 2-1: USB disconnect, address 2
[33312.958918] usb 2-1.3: USB disconnect, address 6
[33321.659608] usb 3-6: USB disconnect, address 9
[33377.167049] usb 2-2: new full speed USB device using ohci_hcd and address 7
[33377.367433] usb 2-2: configuration #1 chosen from 1 choice
[33377.369357] hub 2-2:1.0: USB hub found
[33377.371299] hub 2-2:1.0: 4 ports detected
[33377.698986] usb 2-2.3: new low speed USB device using ohci_hcd and address 8
[33377.809024] usb 2-2.3: configuration #1 chosen from 1 choice
[33377.816281] input: Logitech Optical USB Mouse as /class/input/input8
[33377.816366] input: USB HID v1.10 Mouse [Logitech Optical USB Mouse] on usb-0000:00:13.1-2.3
[33424.190269] usb 2-2: USB disconnect, address 7
[33424.190277] usb 2-2.3: USB disconnect, address 8
[33488.915788] usb 3-5: new high speed USB device using ehci_hcd and address 11
[33489.056971] usb 3-5: configuration #1 chosen from 1 choice
[33591.667872] usb 1-2: new full speed USB device using ohci_hcd and address 2
[33591.868809] usb 1-2: configuration #1 chosen from 1 choice
[33591.870729] hub 1-2:1.0: USB hub found
[33591.872669] hub 1-2:1.0: 4 ports detected
[33592.196357] usb 1-2.3: new low speed USB device using ohci_hcd and address 3
[33592.303409] usb 1-2.3: configuration #1 chosen from 1 choice
[33592.310662] input: Logitech Optical USB Mouse as /class/input/input9
[33592.310744] input: USB HID v1.10 Mouse [Logitech Optical USB Mouse] on usb-0000:00:13.0-2.3
[34008.585220] usb 1-2: USB disconnect, address 2
[34008.585229] usb 1-2.3: USB disconnect, address 3
[34014.410361] usb 3-5: USB disconnect, address 11
[34017.092449] usb 3-5: new high speed USB device using ehci_hcd and address 13
[34017.233548] usb 3-5: configuration #1 chosen from 1 choice
[34028.283312] usb 2-2: new full speed USB device using ohci_hcd and address 9
[34028.484247] usb 2-2: configuration #1 chosen from 1 choice
[34028.486163] hub 2-2:1.0: USB hub found
[34028.488106] hub 2-2:1.0: 4 ports detected
[34028.812796] usb 2-2.3: new low speed USB device using ohci_hcd and address 10
[34028.917837] usb 2-2.3: configuration #1 chosen from 1 choice
[34028.925106] input: Logitech Optical USB Mouse as /class/input/input10
[34028.925189] input: USB HID v1.10 Mouse [Logitech Optical USB Mouse] on usb-0000:00:13.1-2.3
[34086.975264] usb 2-2: USB disconnect, address 9
[34086.975273] usb 2-2.3: USB disconnect, address 10
[34103.457912] usb 1-2: new full speed USB device using ohci_hcd and address 4
[34103.658850] usb 1-2: configuration #1 chosen from 1 choice
[34103.660769] hub 1-2:1.0: USB hub found
[34103.662712] hub 1-2:1.0: 4 ports detected
[34103.986404] usb 1-2.3: new low speed USB device using ohci_hcd and address 5
[34104.093478] usb 1-2.3: configuration #1 chosen from 1 choice
[34104.100659] input: Logitech Optical USB Mouse as /class/input/input11
[34104.100748] input: USB HID v1.10 Mouse [Logitech Optical USB Mouse] on usb-0000:00:13.0-2.3
[34124.333977] usb 1-2: USB disconnect, address 4
[34124.333985] usb 1-2.3: USB disconnect, address 5
[34126.280907] usb 3-5: USB disconnect, address 13
[34130.044238] usb 3-5: new high speed USB device using ehci_hcd and address 16
[34130.184474] usb 3-5: configuration #1 chosen from 1 choice
[34139.040859] usb 1-2: new full speed USB device using ohci_hcd and address 6
[34139.241798] usb 1-2: configuration #1 chosen from 1 choice
[34139.243714] hub 1-2:1.0: USB hub found
[34139.245658] hub 1-2:1.0: 4 ports detected
[34139.570343] usb 1-2.3: new low speed USB device using ohci_hcd and address 7
[34139.676396] usb 1-2.3: configuration #1 chosen from 1 choice
[34139.683665] input: Logitech Optical USB Mouse as /class/input/input12
[34139.683746] input: USB HID v1.10 Mouse [Logitech Optical USB Mouse] on usb-0000:00:13.0-2.3
[34240.600946] usb 1-2: USB disconnect, address 6
[34240.600954] usb 1-2.3: USB disconnect, address 7
[34242.614227] usb 3-5: USB disconnect, address 16
[34246.145388] usb 3-5: new high speed USB device using ehci_hcd and address 18
[34246.285600] usb 3-5: configuration #1 chosen from 1 choice
fowlers@eMachines:~$
brokencrystal
February 15th, 2008, 05:36 PM
When I plug the Zune into the front side USB port, then unplug it, then plug it into the other front side USB port, this is what I get:
[34658.656509] usb 3-6: new high speed USB device using ehci_hcd and address 20
[34658.797706] usb 3-6: configuration #1 chosen from 1 choice
[34689.213270] usb 3-6: USB disconnect, address 20
[34692.073220] usb 3-5: new high speed USB device using ehci_hcd and address 21
[34692.214309] usb 3-5: configuration #1 chosen from 1 choice
[34713.149789] usb 3-5: USB disconnect, address 21
vBulletin® v3.8.7, Copyright ©2000-2012, vBulletin Solutions, Inc.