vratojr
October 23rd, 2011, 09:27 AM
Hello, I have a USB WIFI key plugged to a 3m USB cable extension. The key worked perfectly during the installation of Ubuntu 11.10 64bit but, after reboot it stops working.
lsusb
Bus 001 Device 006: ID 1435:0711 Wistron NeWeb UR055G 802.11bgThis is the output I get:
dmesg:
[62973.868040] usb 1-6: new high speed USB device number 8 using ehci_hcd
[62974.116042] usb 1-6: reset high speed USB device number 8 using ehci_hcd
...
[62974.250024] ieee80211 phy3: Selected rate control algorithm 'minstrel_ht'
[62974.251186] zd1211rw 1-6:1.0: phy3
[62974.356966] usb 1-6: USB control request for firmware upload failed. Error number -71
[62974.356979] usb 1-6: Could not upload firmware code uph. Error number -71But the error code shifts from 71 to 110 to 29
lshw -C network:
*-network DISABLED
description: Wireless interface
physical id: 1
bus info: usb@1:6
logical name: wlan0
serial: 00:10:a7:2e:ce:e9
capabilities: ethernet physical wireless
configuration: broadcast=yes driver=zd1211rw driverversion=3.0.0-12-generic firmware=N/A link=no multicast=yes wireless=IEEE 802.11bg
While this is the output I get if I use the key without the extension cable (and works perfectly):
dmesg
[62812.848038] usb 1-10: reset high speed USB device number 7 using ehci_hcd
....
[62812.982194] ieee80211 phy2: Selected rate control algorithm 'minstrel_ht'
[62812.983523] zd1211rw 1-10:1.0: phy2
[62813.127055] zd1211rw 1-10:1.0: firmware version 4605
[62813.167054] zd1211rw 1-10:1.0: zd1211 chip 1435:0711 v4330 high 00-10-a7 AL2230_RF pa0 g----
lshw -C network:
*-network
description: Wireless interface
physical id: 1
bus info: usb@1:10
logical name: wlan0
serial: 00:10:a7:2e:ce:e9
capabilities: ethernet physical wireless
configuration: broadcast=yes driver=zd1211rw driverversion=3.0.0-12-generic firmware=4605 ip=5.236.27.75 link=yes multicast=yes wireless=IEEE 802.11bg
lsusb
Bus 001 Device 006: ID 1435:0711 Wistron NeWeb UR055G 802.11bgThis is the output I get:
dmesg:
[62973.868040] usb 1-6: new high speed USB device number 8 using ehci_hcd
[62974.116042] usb 1-6: reset high speed USB device number 8 using ehci_hcd
...
[62974.250024] ieee80211 phy3: Selected rate control algorithm 'minstrel_ht'
[62974.251186] zd1211rw 1-6:1.0: phy3
[62974.356966] usb 1-6: USB control request for firmware upload failed. Error number -71
[62974.356979] usb 1-6: Could not upload firmware code uph. Error number -71But the error code shifts from 71 to 110 to 29
lshw -C network:
*-network DISABLED
description: Wireless interface
physical id: 1
bus info: usb@1:6
logical name: wlan0
serial: 00:10:a7:2e:ce:e9
capabilities: ethernet physical wireless
configuration: broadcast=yes driver=zd1211rw driverversion=3.0.0-12-generic firmware=N/A link=no multicast=yes wireless=IEEE 802.11bg
While this is the output I get if I use the key without the extension cable (and works perfectly):
dmesg
[62812.848038] usb 1-10: reset high speed USB device number 7 using ehci_hcd
....
[62812.982194] ieee80211 phy2: Selected rate control algorithm 'minstrel_ht'
[62812.983523] zd1211rw 1-10:1.0: phy2
[62813.127055] zd1211rw 1-10:1.0: firmware version 4605
[62813.167054] zd1211rw 1-10:1.0: zd1211 chip 1435:0711 v4330 high 00-10-a7 AL2230_RF pa0 g----
lshw -C network:
*-network
description: Wireless interface
physical id: 1
bus info: usb@1:10
logical name: wlan0
serial: 00:10:a7:2e:ce:e9
capabilities: ethernet physical wireless
configuration: broadcast=yes driver=zd1211rw driverversion=3.0.0-12-generic firmware=4605 ip=5.236.27.75 link=yes multicast=yes wireless=IEEE 802.11bg