strider3700
October 10th, 2011, 08:20 AM
I've been using an arduino mega for awhile now and it connects just fine when I plug it in. it's dmesg is
[10721.471787] usb 5-1: new full speed USB device using ohci_hcd and address 66
[10721.710252] ftdi_sio 5-1:1.0: FTDI USB Serial Device converter detected
[10721.710313] usb 5-1: Detected FT232RL
[10721.710319] usb 5-1: Number of endpoints 2
[10721.710324] usb 5-1: Endpoint 1 MaxPacketSize 64
[10721.710329] usb 5-1: Endpoint 2 MaxPacketSize 64
[10721.710333] usb 5-1: Setting MaxPacketSize 64
[10721.712115] usb 5-1: FTDI USB Serial Device converter now attached to ttyUSB0
and it shows up in lsusb as
Bus 005 Device 066: ID 0403:6001 Future Technology Devices International, Ltd FT232 USB-Serial (UART) IC
now if I attach the ethernet shield to the mega and then plug it in it doesn't show up in lsusb. and here is the error message in dmesg
[10987.600132] usb 5-1: new full speed USB device using ohci_hcd and address 67
[10987.750158] usb 5-1: device descriptor read/64, error -62
[10988.011789] usb 5-1: device descriptor read/64, error -62
[10988.290173] usb 5-1: new full speed USB device using ohci_hcd and address 68
[10988.441802] usb 5-1: device descriptor read/64, error -62
[10988.700137] usb 5-1: device descriptor read/64, error -62
[10988.981796] usb 5-1: new full speed USB device using ohci_hcd and address 69
[10989.401784] usb 5-1: device not accepting address 69, error -62
[10989.551788] usb 5-1: new full speed USB device using ohci_hcd and address 70
[10989.970119] usb 5-1: device not accepting address 70, error -62
[10989.970192] hub 5-0:1.0: unable to enumerate USB device on port 1
I can't figure out what device "descriptor read/64, error -62" means or even where to start figuring this out. Any suggestions?
[10721.471787] usb 5-1: new full speed USB device using ohci_hcd and address 66
[10721.710252] ftdi_sio 5-1:1.0: FTDI USB Serial Device converter detected
[10721.710313] usb 5-1: Detected FT232RL
[10721.710319] usb 5-1: Number of endpoints 2
[10721.710324] usb 5-1: Endpoint 1 MaxPacketSize 64
[10721.710329] usb 5-1: Endpoint 2 MaxPacketSize 64
[10721.710333] usb 5-1: Setting MaxPacketSize 64
[10721.712115] usb 5-1: FTDI USB Serial Device converter now attached to ttyUSB0
and it shows up in lsusb as
Bus 005 Device 066: ID 0403:6001 Future Technology Devices International, Ltd FT232 USB-Serial (UART) IC
now if I attach the ethernet shield to the mega and then plug it in it doesn't show up in lsusb. and here is the error message in dmesg
[10987.600132] usb 5-1: new full speed USB device using ohci_hcd and address 67
[10987.750158] usb 5-1: device descriptor read/64, error -62
[10988.011789] usb 5-1: device descriptor read/64, error -62
[10988.290173] usb 5-1: new full speed USB device using ohci_hcd and address 68
[10988.441802] usb 5-1: device descriptor read/64, error -62
[10988.700137] usb 5-1: device descriptor read/64, error -62
[10988.981796] usb 5-1: new full speed USB device using ohci_hcd and address 69
[10989.401784] usb 5-1: device not accepting address 69, error -62
[10989.551788] usb 5-1: new full speed USB device using ohci_hcd and address 70
[10989.970119] usb 5-1: device not accepting address 70, error -62
[10989.970192] hub 5-0:1.0: unable to enumerate USB device on port 1
I can't figure out what device "descriptor read/64, error -62" means or even where to start figuring this out. Any suggestions?