oneguynick
May 24th, 2006, 07:18 AM
Software
Make sure you are running the latest versions of firmware for the Treo 650. I happen to have an unlocked edition so this is very easy to fix from PalmOne. I recommend going with the latest but this isnt a deal breaker. I am going to assume this from a total newbie position as yes, you can use pppd or wvdial from CLI. For our test we will be using Ubuntu 6.06 and Gnome-ppp. To enable “tethered” mode on the Treo you maybe lucky and dial #*83843733. I was unable with GSM and Cingular and instead used this software which works wonderfully. If anything they also officially support Linux. Sweet!
http://mobile-stream.com/usbmodem.html
Hardware
The hotsync USB cable will be all that is needed. I have problems in the past plugging into an external USB hub so keep that in mind.
Installing Software
I downloaded the USB Treo program and explored the zip file. I extracted the PRC to a SD-Card
PALM\LAUNCHERS
and reinserted into the Treo. There was the program. I clicked enable USB modem and plugged the USB hotsync cable in. At this point I
apt-get install gnome-ppp
and waited for that to finish. Check dmesg for ttyACM0 to ensure that the kernel did pickup the hotplug device.
Gnome-PPP Settings
Before we can even start on that portion of the install lets enable a few LCP options we will need to ensure the connection stays put.
sudo vi /etc/ppp/options
Find in the conf file:
lcp-echo-failure 4 and change it to... lcp-echo-failure 0
Next run Gnome-PPP from your applications menu. The settings most important here will be the username and password:
u: WAP@CINGULARGPRS.COM
p: CINGULAR1
Also for the phone number put: *99***1#
The final dialog box should look like this:
http://i39.photobucket.com/albums/e192/oneguynick/Screenshot-GNOME20PPP.png
Lets digg into some of the options you may need to check to ensure this is transparent:
Init Strings needed:
http://i39.photobucket.com/albums/e192/oneguynick/Screenshot-Init20Strings.png
Setup Dialog Box 1:
http://i39.photobucket.com/albums/e192/oneguynick/Screenshot-Setup.png
Setup Dialog Box 2:
http://i39.photobucket.com/albums/e192/oneguynick/Screenshot-Setup-1.png
After all is said and done. Click connect! You should see the gnome-ppp dock itself and lights start flashing. Something to keep in mind is that if your default route is pointing to eth0/wifi0 you will need to pull those interfaces down before the ppp0 can take over. Enjoy!
Make sure you are running the latest versions of firmware for the Treo 650. I happen to have an unlocked edition so this is very easy to fix from PalmOne. I recommend going with the latest but this isnt a deal breaker. I am going to assume this from a total newbie position as yes, you can use pppd or wvdial from CLI. For our test we will be using Ubuntu 6.06 and Gnome-ppp. To enable “tethered” mode on the Treo you maybe lucky and dial #*83843733. I was unable with GSM and Cingular and instead used this software which works wonderfully. If anything they also officially support Linux. Sweet!
http://mobile-stream.com/usbmodem.html
Hardware
The hotsync USB cable will be all that is needed. I have problems in the past plugging into an external USB hub so keep that in mind.
Installing Software
I downloaded the USB Treo program and explored the zip file. I extracted the PRC to a SD-Card
PALM\LAUNCHERS
and reinserted into the Treo. There was the program. I clicked enable USB modem and plugged the USB hotsync cable in. At this point I
apt-get install gnome-ppp
and waited for that to finish. Check dmesg for ttyACM0 to ensure that the kernel did pickup the hotplug device.
Gnome-PPP Settings
Before we can even start on that portion of the install lets enable a few LCP options we will need to ensure the connection stays put.
sudo vi /etc/ppp/options
Find in the conf file:
lcp-echo-failure 4 and change it to... lcp-echo-failure 0
Next run Gnome-PPP from your applications menu. The settings most important here will be the username and password:
u: WAP@CINGULARGPRS.COM
p: CINGULAR1
Also for the phone number put: *99***1#
The final dialog box should look like this:
http://i39.photobucket.com/albums/e192/oneguynick/Screenshot-GNOME20PPP.png
Lets digg into some of the options you may need to check to ensure this is transparent:
Init Strings needed:
http://i39.photobucket.com/albums/e192/oneguynick/Screenshot-Init20Strings.png
Setup Dialog Box 1:
http://i39.photobucket.com/albums/e192/oneguynick/Screenshot-Setup.png
Setup Dialog Box 2:
http://i39.photobucket.com/albums/e192/oneguynick/Screenshot-Setup-1.png
After all is said and done. Click connect! You should see the gnome-ppp dock itself and lights start flashing. Something to keep in mind is that if your default route is pointing to eth0/wifi0 you will need to pull those interfaces down before the ppp0 can take over. Enjoy!