PDA

View Full Version : [ubuntu] SiS900 PCI Fast Ethernet Connection Problem



tchaikovsky88
October 11th, 2010, 09:29 PM
Hey,
i just installed ubuntu 10.04 with a new motherboard. All hardware is doing just fine except my integrated lan network device (SiS900) witch doesn't connect to the network.

I had to plug in another pci lan card to access internet, and i could be ok with that solution, but i would like to activate the WOL capabilities of my board so i'm hopping anyone comes up with a solution since it looks to me like an hardware configuration issue.



root@xxxx:~# ifconfig
eth0 Link encap:Ethernet HWaddr 00:10:4b:bc:84:55
inet addr:192.170.1.149 Bcast:192.170.1.255 Mask:255.255.255.0
inet6 addr: fe80::210:4bff:febc:8455/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:4579 errors:0 dropped:0 overruns:0 frame:0
TX packets:836 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1579204 (1.5 MB) TX bytes:116019 (116.0 KB)
Interrupt:17 Base address:0x8f80

eth1 Link encap:Ethernet HWaddr 00:0b:6a:a4:20:09
inet6 addr: fe80::20b:6aff:fea4:2009/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:340 errors:0 dropped:0 overruns:0 frame:0
TX packets:13 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:35537 (35.5 KB) TX bytes:2862 (2.8 KB)
Interrupt:19 Base address:0xd400

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:8 errors:0 dropped:0 overruns:0 frame:0
TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:480 (480.0 B) TX bytes:480 (480.0 B)





root@scooby:~# dmesg | grep eth0
[ 1.108364] eth0: SiS 900 PCI Fast Ethernet at 0xd400, IRQ 19, 00:0b:6a:a4:20:09
[ 23.652281] udev: renamed network interface eth1 to eth0
[ 23.654006] udev: renamed network interface eth0_rename to eth1
[ 25.194570] eth0: setting full-duplex.
[ 35.264059] eth0: no IPv6 routers present

root@scooby:~# dmesg | grep eth1
[ 23.652281] udev: renamed network interface eth1 to eth0
[ 23.654006] udev: renamed network interface eth0_rename to eth1
[ 27.185005] eth1: Media Link On 100mbps full-duplex
[ 35.760051] eth1: no IPv6 routers present

*Why is udev renaming my devices?




root@xxxx:~# ethtool eth0
Settings for eth0:
Supported ports: [ TP MII ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Link partner advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
Link partner advertised pause frame use: No
Link partner advertised auto-negotiation: Yes
Speed: 100Mb/s
Duplex: Full
Port: MII
PHYAD: 24
Transceiver: internal
Auto-negotiation: on
Current message level: 0x00000001 (1)
Link detected: yes

root@xxxx:~# ethtool eth1
Settings for eth1:
Supported ports: [ TP MII ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Link partner advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
Link partner advertised pause frame use: No
Link partner advertised auto-negotiation: Yes
Speed: 100Mb/s
Duplex: Full
Port: MII
PHYAD: 1
Transceiver: internal
Auto-negotiation: on
Supports Wake-on: pg
Wake-on: d
Current message level: 0x000000c5 (197)
Link detected: yes