PDA

View Full Version : Blluetooth properties glib error



youoh
June 8th, 2010, 06:56 AM
i could not connect my keyboard so i'm writing with onboard


bluetooth-properties
** Message: adding killswitch idx 0 state 1
** Message: killswitch 0 is 1
** Message: killswitches state 1

(bluetooth-properties:4184): GLib-GObject-WARNING **: cannot register existing type `BluetoothClient'

(bluetooth-properties:4184): GLib-CRITICAL **: g_once_init_leave: assertion `initialization_value != 0' failed


some terminal guru's the who can help me to connect my keyboard there

Kevbert
June 8th, 2010, 04:35 PM
Looks like bluetooth is non-responsive. If I plug in my bluetooth USB dongle the Applet stays greyed out and yet I can turn bluetooth on and off. Clicking on Preferences and Set up new device do nothing. PC can see phone though:


~$ hcitool scan
Scanning ...
00:1E:DC:86:44:2D K800i
~$ sudo hcitool info 00:1E:DC:86:44:2D
Requesting information ...
BD Address: 00:1E:DC:86:44:2D
Device Name: K800i
LMP Version: 2.0 (0x3) LMP Subversion: 0x520
Manufacturer: ST Microelectronics (48)
Features: 0xff 0xe9 0x8d 0xfe 0x9b 0xe9 0x00 0x00
<3-slot packets> <5-slot packets> <encryption> <slot offset>
<timing accuracy> <role switch> <hold mode> <sniff mode>
<park state> <SCO link> <HV3 packets> <u-law log> <A-law log>
<CVSD> <power control> <transparent SCO> <broadcast encrypt>
<EDR ACL 2 Mbps> <EDR ACL 3 Mbps> <enhanced iscan>
<interlaced iscan> <interlaced pscan> <inquiry with RSSI>
<extended SCO> <EV4 packets> <EV5 packets> <AFH cap. slave>
<AFH class. slave> <3-slot EDR ACL> <5-slot EDR ACL>
<AFH cap. master> <EDR eSCO 2 Mbps> <EDR eSCO 3 Mbps>
<3-slot EDR eSCO>
~$
I read somewhere the one or two old bluetooth packages were no longer supported. It may be that we need to wait for new packages.
Xsession-errors:

(bluetooth-properties:2043): GLib-GObject-WARNING **: cannot register existing type `BluetoothClient'

(bluetooth-properties:2043): GLib-CRITICAL **: g_once_init_leave: assertion `initialization_value != 0' failed

(bluetooth-properties:2045): Unique-DBus-WARNING **: Error while sending message: Did not receive a reply. Possible causes include: the remote application did not send a reply, the message bus security policy blocked the reply, the reply timeout expired, or the network connection was broken.

(bluetooth-properties:2047): Unique-DBus-WARNING **: Error while sending message: Did not receive a reply. Possible causes include: the remote application did not send a reply, the message bus security policy blocked the reply, the reply timeout expired, or the network connection was broken.

(bluetooth-wizard:2050): GLib-GObject-WARNING **: cannot register existing type `BluetoothClient'

(bluetooth-wizard:2050): GLib-CRITICAL **: g_once_init_leave: assertion `initialization_value != 0' failed
** Message: RFKILL event: idx 1 type 2 op 2 soft 1 hard 0

** Message: updating killswitch status 1
** Message: killswitch 1 is 0
** Message: killswitches state 0
** Message: killswitch 1 is 0
** Message: killswitches state 0
** Message: RFKILL event: idx 1 type 2 op 2 soft 0 hard 0

** Message: updating killswitch status 1
** Message: killswitch 1 is 1
** Message: killswitches state 1
** Message: killswitch 1 is 1
** Message: killswitches state 1

(bluetooth-wizard:2052): Unique-DBus-WARNING **: Error while sending message: Did not receive a reply. Possible causes include: the remote application did not send a reply, the message bus security policy blocked the reply, the reply timeout expired, or the network connection was broken.