saz
March 21st, 2009, 10:30 AM
Hi there!
I used to use wireless, but now I have the possibility to use cable.
But for some reason I can't get it to work, not in arch, gentoo, knoppix (livecd) or ubuntu (livecd).
It always times out when trying to get an IP... And on dmesg I always get the same "forcedeth: eth0: no link during initialization" error.. :-(
ethtool
[sa@Feio ~]$ sudo ethtool eth0
Settings for eth0:
Supported ports: [ MII ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Advertised auto-negotiation: Yes
Speed: Unknown! (65535)
Duplex: Unknown! (255)
Port: MII
PHYAD: 19
Transceiver: external
Auto-negotiation: on
Supports Wake-on: g
Wake-on: d
Link detected: no
route
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
192.168.0.1 * 255.255.255.0 U 0 0 0 eth0
default 192.168.0.1 0.0.0.0 UG 0 0 0 eth0
dmesg
forcedeth 0000:00:11.0: irq 758 for MSI/MSI-X
eth0: no link during initialization.
ifconfig
[sa@Feio ~]$ ifconfig -a
eth0 Link encap:Ethernet HWaddr 00:1A:92:83:1D:8D
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:22 Base address:0x4000
hope you can help!
I used to use wireless, but now I have the possibility to use cable.
But for some reason I can't get it to work, not in arch, gentoo, knoppix (livecd) or ubuntu (livecd).
It always times out when trying to get an IP... And on dmesg I always get the same "forcedeth: eth0: no link during initialization" error.. :-(
ethtool
[sa@Feio ~]$ sudo ethtool eth0
Settings for eth0:
Supported ports: [ MII ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Advertised auto-negotiation: Yes
Speed: Unknown! (65535)
Duplex: Unknown! (255)
Port: MII
PHYAD: 19
Transceiver: external
Auto-negotiation: on
Supports Wake-on: g
Wake-on: d
Link detected: no
route
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
192.168.0.1 * 255.255.255.0 U 0 0 0 eth0
default 192.168.0.1 0.0.0.0 UG 0 0 0 eth0
dmesg
forcedeth 0000:00:11.0: irq 758 for MSI/MSI-X
eth0: no link during initialization.
ifconfig
[sa@Feio ~]$ ifconfig -a
eth0 Link encap:Ethernet HWaddr 00:1A:92:83:1D:8D
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:22 Base address:0x4000
hope you can help!